Search Documents

By A. F. Collings

The processing of heavy mineral concentrates can be enhanced by the use of power ultrasound to clean their surfaces of oxidation products and fine coatings, mainly through the large, but very localized forces, produced by cavitation. Results are presented of the application of power ultrasound to remove coatings from the surfaces of mineral sand concentrates in order to improve the sharpness of their high-tension separation and, in some cases, the quality of the low iron components such as zircon. Improvements of 10–15% in recovery and up to 20% in grade compared to unsonicated material were achieved in a single stage laboratory high-tension separation. Cavitation also ensures that a fresh, clean surface is presented to leachants during the leaching of suspended solids. At the same time, the effect of cavitation and the shearing effect of the sound wave passing over the solids ensure that the saturated boundary layer is kept to a minimum if not completely removed. This application of power ultrasound helps to speed up leaching processes as applied to the removal of excess alumino-silicate contaminants in some ilmenite. Keywords: Ultrasound, power ultrasound, heavy minerals, processing.

Jan 1, 2003

Mineral sand beneficiation plants comprise a complex combination of electrostatic, magnetic and gravity based separation techniques. These are combined and replicated in ways that provide the most efficient and cost effective separation of the valuable components. On line instrumentation has been developed at the JKMRC (eg. conductor/non-conductor(CNC) ) to measure the properties of the dry plant process streams. This paper provides results from the recent development of a novel low cost mass flow meter and discusses their combined use with the CNC instrumentation for the control of dry separation circuits.

Jan 1, 2003

By C. A. Rawlins

In an underground mine the ingress of heat can generally be attributed to two sources (Rock exposure and artificial mechanisms). The heat load relating rock exposure is subdivided into stoping [~40%] and haulages [~20%]. Rock is exposed to the ambient air and as a mine increases in depth the VRT (Virgin Rock Temperature) increases which leads to more heat ingress underground. To counter the heat ingress, especially in low-seam stoping areas of a deep level mine, air is, a) cooled artificially, b) the amount of rock exposed is reduced in the back areas of a stope by backfill applications, and c) ventilation air is used more efficiently. The heat reduction within a stope due to placed backfill could amount to ~50% for operations mining at a mean rock breaking depth of about 4500 mbc (metres below collar). Unfortunately, due to backfill transport methods, the physical fluid properties and application methods adopted, additional heat is induced into the air. The heat ingress due to backfill application could amount to as much as 25% of the overall in-stope heat load. This heat influx, seen as a negative aspect of backfill operations, is nevertheless overshadowed by the overall in-mine heat load reduction capability of about 20% attainable. The in-stope benefit [~50%] attainable from backfill operations could be increased with the incorporation of a heat exchange (cooling) methodology to offset the additional heat ingress into the surrounding air of a deep underground mine.

Jan 1, 2003

By I. R. Firth, D. L. Taylor

Metal mining operations, in particular gold mining operations, use intensive ore control procedures in order to manage the extraction of ore zones from benches containing both ore and waste material. Typical grade control procedures rely on blast hole samples to indicate ore grade. Statistical techniques and geological controls are then used to create two-dimensional polygons, which indicate zones of material designated as ore. These ore-polygons are calculated using pre-blast material locations and are generally not corrected for rock movement caused by blasting. This lack of correction appears to exacerbate the material mischaracterization problem of sending ore to the waste dump and/or waste to the mill. One Nevada gold mining company has estimated that this could be a $10 million per year problem for their operations. Using a simplified vector field algorithm, a method of taking point movement data and interpolating post-blast positions for all nodes in a polygon has been developed. Currently working in 2-dimentions (X-Y), this algorithm utilizes the movement vectors calculated from pre-and post-blast positions of targets placed in a blast, to generate a spatial transformation function for any point on the bench. This transformation is then applied to the nodes of the ore-polygons to produce modified dig lines ore polygons reflecting distortion and movement resulting from the blast. The method as implemented uses common mine planning routines and is performed using the Surpac software suite. The method may be adapted to use any pre-and post-blast point movement data available, and most mine planning suites include the simple interpolation algorithms used. Keywords: Blast movement; Ore control; Open pit blasting; Grade control

Jan 1, 2003

By Kurt R. P Petersen

This paper discusses the current approaches to modelling the DMS cyclone within the De Beers group. Current efforts are split into short term value-adding process understanding and longer term semi-fundamental analysis of separation mechanisms. To date, the basic applied approach has yielded significant value to the group, enabling operators to focus on simple diagnostic measures to control their process. The more involved modelling approach has given rise to a new understanding of the separation field, in particular that the high density gradients within a cyclone are highly localised, indicating that separation of medium to heavy density material takes place low in the cone. The model has proven to be conceptually robust, but still requires further development and validation to become a complete modelling and simulation tool for De Beers.

Jan 1, 2006

By M. L. Baharani

Looking for an idyllic paradise that has investment and business potential as spectacular as the stunning views of mountains, the rich Ganesh Himal zinc-lead deposit exposed between 4,050 m and 5,000 m is the answer. Arising from the sea floor in a span of 55 million years, the enchanting Himalayas had remained one of the most potent factors influencing the Asian region. The challenges of the mighty Himalayas notwithstanding, it continues to provide opportunities for the humankind in optimum usage of the natural resources and sustainable development. Optimal management of natural resources in mountain areas through decision support tools offered by remote sensing will go a long way in realization of the Ganesh Himal Zinc-Lead Project. The authors have a real life endeavor spanning over 37 years in developing a mining industry in a mountainous region of Nepal and an attempt to integrate with the development of other natural attributes of the region. With rapid acceleration of science and technology, humankind has acquired power to transform his environment countless ways and on an unprecedented scale. While mineral resources are the pillars on which we have built industry and infrastructure, industrial countries in the North have been in the forefront of technological advancements, the developed countries of the South have been at the receiving end of exploitation of mineral resources worldwide. A relationship with natural environment, re-crafted by the civilizing impulse, to meet human demands are upcoming challenges for management of natural resource in sustainable manner for a livable world.

Jan 1, 2008

By P. He

Abstract This paper introduces the test results of dark-gray calcium-shale, discusses the infection of strength characteristic and deformation characteristic due to the angle between structural planes. Keywords calcium-shale, failure form, strength, deformation characteristic, structural planes. Zusammenfassung: basier auf der Anwendung von Problematik des Felsenbauprojektes und Beschaffenheit Felsen unter Beaugnshme auf den Zustand des Druckes von einzeler Welle legt dieser Text dar, wie der Winkel der Schichtstrukturflaeche des schwarzgrau kalziumhaltigen Schieferblocks auf die Zerstoerungs-, Intensitaets- und Deformationseigenschaften einwirkt. Schluesselwoerter: schwarzgrau kalziumhaltigen Schiefer, Zerstoerungseigenschften, Intensitaetseigenschften, Deformationseigenschaften, Flaeche dar Schichtstruktur. Résumé – En fonction de la configuration du massif rocheux sous l’état de la contrainte de pression axiale simple et de la pratique de l’ingénierie de roches, le présent article fait la déscription concernant l’influence de l’inclinaison ? de la couche de structure stratifiée du bloc de schiste calcaire gris noir sur ses caractéristiques de destruction, sa spécificité de résistance ainsi que sa nature de déformation. Mot clés – Schiste calcaire gris noir, Caractéristiques de destruction, Spécificité de résistance, Nature de déformation, Couche de structure stratifiée

Jan 1, 2003

By J. Lux, B. Clermont

Magotteaux, with the co-operation of Anglo Platinum, has erected a fully instrumented pilot plant at Frank concentrator, which is being used to study the influence of a variety of grinding parameters. This paper will discuss only the influence of mill speed and pulp density on secondary stage grinding. A Ø0.82 x1 m open circuit mill was used with reclaimed Merensky tailings as feed. The conclusions apply to this pilot plant but further investigation needs to be done to verify whether the same trends will be applicable to a large industrial-scale mill.

Jan 1, 2004

By A. Aitio

Sustainable development is one of the central themes of the work of the World Health Organization; chemical safety is one of its important components. For more than 25 years, WHO has had specialized units for assisting member countries in dealing with their problems in chemical safety. For one of the units involved, International Programme on Chemical Safety, a reorientation is in progress to make best use of existing resources, and to prioritise the work to optimally correspond to the needs of the member countries. The risk assessment work of IPCS, and specifically, the work on chromium and chromium compounds, are discussed.

Jan 1, 2004

By M. Hermanus

1. INTRODUCTION It gives me great pleasure to extend my warmest greetings to everyone attending the 30th International Conference of Safety in Mines Research Institutes. I would also like to bid a special welcome to all of the international delegates who have travelled to Johannesburg to take part in what surely be a most rewarding session of deliberations. As you come together over next four days, you will have a wonderful opportunity to exchange ideas and information on strategies and practices for the implementation of sustainable patterns of development. The objectives of this meeting are both timely and far-reaching, as countries around the globe work towards the sustainable use of the world resources. Each of you brings a high level of expertise to these deliberations. I know that you will make the most of this opportunity to address the challenges and opportunities to highlight the most innovative and technologically efficient methods of social protection in order to ensure an increase in the quality of life, health, safety and living environment for the peoples of the Africa. Our country, although endowed with an immense and diverse array of mineral deposits, is perhaps best known in the mining industry for the fact that it is the world’s biggest producer of gold. Although South African gold production has declined over the past years and the industry faces serious problems, it is a myth that the South African industry is moribund. There is a new energy coursing through the South African producers which will ensure their powerful presence for many years to come, based not only on their domestic production but also and probably increasingly on their external operations. Africa features prominently in the latter category.

Jan 1, 2003

By R. Strydom, J. H. Selby

Published information is available on the radiological impacts of disposing of zircon sand in a landfill. Zircon flour by virtue of its finer particle size presents a different set of issues during disposal. This paper describes two options for disposal of such fine grained materials – namely incorporation into concrete aggregates and agglomeration by addition of cement. The study considers the radiological exposure of the public from such disposal methods and concludes that these options are viable alternatives for the safe disposal of waste zircon flour. The disposal of zircon into concrete aggregates at a rate of 10 per cent produces a sufficiently low effect to allow such aggregates to be used in building foundations or other such mass concrete applications. The use of cement agglomeration methods will also provide a safe method of landfill disposal provided at least 20 cm of soil cover is included.

Jan 1, 2003

By G Njowa

Mineral resource evaluation and estimation process is not an exact science; however it depends on the knowledge and experience of the competent person and his ability to apply his mind, make reasonable assumptions, interpretations and exercise sound judgment in the mineral resource estimation process. The mineral resource evaluation results in a mineral resource statement are disclosed to investors. The minerals industry is presently undergoing rapid changes in legislation governing the public reporting of mineral assets. It has gone through different phases of development with respect to the reporting of mineral resources and mineral reserves (mineral assets). In the past no reporting was done and currently mineral assets are reported as a supplementary section that briefly describes the mineral asset termed ?the mineral reserve and mineral resource statement?. The current industry trend appears to be going towards recognition and disclosure of the mineral assets on to the balance sheet. This paper explores the salient issues behind the mineral resources and mineral reserve statement of vein and reef deposits published in the public domain. It also highlights the potential misleading consequences of these issues and which filter through to the valuation of these particular mineral assets. The creation of reporting standards in the minerals industry has made significant inroads in standardizing and consolidating the interpretation and understanding of the different classification categories in the industry in an effort to promote common interpretation towards these salient issues.

Jan 1, 2008

By S. J. Frank

The development of feedforward semi-empirical control models for furnaces and the evaluation of mass balances are based on plant data. The models can only be as good as the data and it is therefore required to know the inherent uncertainty associated with the plant data. This uncertainty stems mainly from the fact that the slag, alloy or dust, have a distributed nature that depends on the degree of mixedness. It is commonly accepted that melts from open bath furnaces are well-mixed, and submerged arc furnaces less so. The impact of this assumption is significant, as a reasonably homogeneous melt could be represented by one sample only. As so much of metallurgical control depends on the assay information of the alloy and slag melts from furnaces, it was decided to characterise the possible variation in melt chemistry and temperature. Sampling campaigns and continuous temperature measurement of the melts were performed for different alloy and slag taps at a major ferrochrome producer. Both a submerged arc furnace and open arc furnace are evaluated in this way, by way of comparison. The slags of both open arc and submerged arc furnaces were found to be of similar degrees of homogeneity, with much spatial variance in the reducible iron and chromium oxides. However, it was found that the alloy melts deriving from open arc furnaces were significantly less homogeneous than the alloy derived from submerged arc furnace alloy production. The compositional variance could be related to the furnace operating conditions and it affects both metallurgical accounting and process control. In all cases it was found that the variance in melt solute components are larger than can be ascribed to analysis instrument error. It will be shown how this predetermined variance in melt composition could be included in process modelling and control.

Jan 1, 2004

By I T. Tshabalala

In typical conventional narrow vein stoping operations, the use of temporary support components to offer some support to workers, whilst the permanent and generally more elaborate support system gets installed or constructed, still results in injuries to people. The authors wishes to explore the probability and practicality of making use of new generation support products to make the support operations safer as well as enhance productivity in the stope face. This paper will examine the use of Autorock Drills as a means to drill roof support holes and install appropriate support components into these holes, as well as the application of ?Thin Spray Liners?, commonly called TSL?s as an additional means of creating a safer operating environment. The installation of netting as a means of roof protection and other support aspects such as cemented roof-bolts will also be explored. These proposed items are envisaged to improve the safety of our people and reduce production down time and increase production and productivity.

Jan 1, 2008

By S. Matsuyama, S. Tomita, H. Kawahara, G. Deguchi

A proper management system of coal mine methane gas associated with underground mining activities is essential for the mine safety due to its nature of explosion. Optimum design of the mine ventilation and gas drainage need accurate prediction of gas flow rate emitted by mining activities. Permeability to gas, which is affected by stress conditions of surrounding rock mass, governs the emission rate of the gases. JCOAL has developed a three dimensional FEM simulation program named Mine Gas Flow 3D (MGF-3D). MGF-3D is designed to predict the volume of methane gas emitted from surrounding coal and rock seams based on stress distribution and permeability change which are determined by 3D stress analysis. In MGF-3D, stress change and/or expansion of fractured zone affected by mining is calculated at the first and then gas emission into roadways and longwall panels under the determined stress conditions is calculated using Darcy’s law. MGF-3D also can set up a number of pre-drainage holes and estimate drainage gas volume from each hole. This function makes MGF-3D remarkable program. These simulations for gas emission can contribute to mine gas utilization plan. Comparison between actual measurement of gas emission in the underground mine and simulation results has been performed and availability for the mine safety and problems with MGF-3D are discussed in this report.

Jan 1, 2003

By Jeffrey C. Hillman

The need to recruit locally produced engineers by the South African Mining Industry led to the Engineering Faculty at the University of the Witwatersrand developing a number of academic bridging initiatives for educationally disadvantaged students. The graduation rate achieved during the initial five years of operation by the most successful of these programmes has been on a par with that of al other students but the performance of subsequent intakes has declined to such an extent that the continuance of this scheme could now be at risk. One reason for this reduction in throughput is that many of the applicants for the increasing number of mining bursaries have been more interested in the bursary than the profession and have either failed or dropped out due to a lack of application and motivation. This will have serious consequences for both Wits and the Industry if it continues and some method of identifying unsuitable or suspect applicants needs to be introduced as a mater of urgency. It is recommended that an introductory course be set up at a working mine that would be run under the auspices of Wits, as a joint venture with industry, and include a level of academic input that would provide both bridging needs and certain first year credits. The final form of this course will require extensive consultation with al parties but needs to be completed before the end of 1996. It is further recommended that the advertising and promotion of mining careers be expanded and much improved.

Jan 1, 1996

By A. Lane

The socio economic risks of mining in South Africa have been emerging for some time now, and have been brought into sharp relief by recent events in the platinum sector. The slow pace of social upliftment in the country has lead to widespread social unrest with consequent calls for different forms of resource nationalism. Fundamentally, the key stakeholders are not fully aligned, and are not engaging productively. This poses significant above-the-ground risk to mining companies. Measuring social impact, deploying inclusive solutions and engaging effectively with stakeholders are three ways in which mining companies can mitigate this risk.

Jan 1, 2012

By Baruch Grinbaum, Edwin Bwalya, Robert Minango, Deogratias Bukunkwe

Solvent extraction of Cu from acidic leach, using an oxime extractant, e.g. LIX 984 or Acorga is a well known and established process. As the process advances, Cu is extracted to the solvent and is replaced by H+ in the aqueous phase. At high acidity the distribution coefficient of Cu between the solvent and the aqueous phase decreases, and eventually relatively high concentration of Cu remains in the raffinate, regardless of the number of equilibrium stages. In many processes this phenomenon is immaterial, as the raffinate returns to the leaching and no copper is lost. But when the copper raffinate is used for processing of additional metals, minimal concentration of Cu in the raffinate is essential for an effective process. The recommended process includes three steps: 1. SX-1: Standard extraction of Cu with oxime. The resulting raffinate contains about 6-8 g/L Cu and 50 g/L H2SO4. 2. SX-N: Extraction of most of the acid into an amine-based solvent, and stripping it with a base, e.g. aqueous ammonia, caustic, Na2CO3 etc. The extraction removes no metals, but decreases the concentration of acid from 50 to 10 g/L. 3. SX-2: Extraction of the neutralized solution once more with oxime, to remove the residual copper. Such a process enables one to get down to 100-150 ppm Cu in the final raffinate. This process was developed and tested in the R&D facility in Chambishi Metals plc, by a joint team of Chambishi & Bateman, using Cognis LIX 984N and real solutions from the plant. In the laboratory scale, the equilibrium isotherms for SX-1, SX-2 and the neutralization were developed. Computer simulation of the results showed that the optimal configuration is two stages for both extraction and stripping for SX-1. For SX-2 2-3 stages of extraction and two stages of stripping are needed. The stripping stages may be common to both SX-1 and SX-2. The neutralization of SX1 raffinate was tested both by conventional precipitation with lime and by extraction with Alamine based solvent extraction and stripping with a solution of 10% NaOH. For the SX-N only one stage was needed for both the extraction and stripping. The bench scale pilot plant was run for both SX-1 & SX-2. The results were very similar to the simulated ones, and the configuration of 2E2S for SX-1 and 3E=2S for SX-2 delivered the required raffinate with less than 150 ppm Cu.

Jan 1, 2005

By Janet M. Epps

The international climate regulating environmental management in mining is rapidly evolving through the combined influences of the development of international guidelines, resolutions, protocols, treaties and conventions; the influences of the international lending and aid institutions who seek a consistent but constantly evolving standard of environmental performance from their clients; the legal precedents being developed in courts al over the world; and the activities of multinational countries who tend to rapidly upgrade technological performance through their international activities (particularly influencing developing countries). In this rapidly evolving regulatory environment, the more 'models' available to this international pool of resource materials that demonstrate practical. cost-effective and (most desirably) incentive based regulatory mechanisms, the better will be the eventual body of 'international standards' we will al have to work with. Australia can make a significant contribution to this process, however, it has only been on the margin of this dynamic, North American and European led process, up to this time. It is in the Australian minerals and energy industry's best interest to take an active part in the evolution and direction of this process.

Jan 1, 1996

By S. Sakurai, N. Shimizu

The stability of slopes is a crucial problem not only in open pit mines, but also in civil engineering situations. The deformational behaviour of slopes is in general monitored during/after the excavation by carrying out field measurements where displacement measurements are commonly adopted. In monitoring the slope stability it should be emphasized that the measurement results must be properly interpreted so as to assess whether the slopes are stable or become unstable in the future. In order to interpret the data, back analysis is extremely useful. In this paper a slope stability monitoring system is described. It consists of displacement measurements by GPS, and a back analysis of measured data. The use of GPS has a great advantage, because of the fact that continuous displacement measurements with high accuracy for a large extent of concerned area can be easily achieved. On the other hand, the back analysis can reveal the mechanical characteristics of the ground, which make it possible to assess the stability of slopes quantitatively.

Jan 1, 2006