Search Documents

By S. Okubo, K. Fukui

Empirical equations established for estimating the rock strength of the working face based on the cutting forces of a tunnel boring machines (TBM) are further examined and discussed with respect to the dominant factors affecting TBM performance. Constants in the equations are related to TBM-specific parameters such as excavation (tunnel) diameter, cutter diameter, and cutter distance. The relationship between the constants and the TBM specifications is examined in this study on the basis of data collected at ten tunnels, and it is found that the constants are most strongly influenced by the cutter diameter and tunnel diameter. Zur Schätzung der Gesteinsfestigkeit an der Arbeitsfläche ermittelte empirische Gleichungen, die auf den Schneidekräften von Tunnelbohrmaschinen (TBM) beruhen, wurden weiter im Hinblick auf die vorherrschenden, die Leistung der TBM beeinflussenden Faktoren hin untersucht und diskutiert. In der Gleichung enthaltene Konstanten werden zu den TBM-spezifischen Parametern wie Auschachtungs- (Tunnel) Durchmesser, Schneidendurchmesser und Schachtlänge in Beziehung gesetzt. Die Beziehung zwischen diesen Konstanten und den technischen Daten der TBM wird in dieser Studie auf der Basis der bei 10 Tunnelbauten gesammelten Daten untersucht. Dabei wurde gefunden, dass diese Konstanten am stärksten von den Durchmessern der Schneiden und der Tunnel beeinflusst werden. Cette étude examine et discute les équations empiriques permettant d'estimer la résistance de la roche attaquée aux forces de coupe des tunneliers dans le cadre de l'étude des facteurs dominants affectant les performances des tunneliers. Les constantes de ces équations concernent les paramètres spécifiques des tunneliers comme le diamètre d'excavation (du tunnel), le diamètre du couteau et la distance de coupe. Cette étude examine le rapport entre ces constantes et les caractéristiques techniques des tunneliers d'après des données collectées dans dix tunnels et elle conclut que ces constantes sont principalement influencées par le diamètre du couteau et le diamètre du tunnel.

Jan 1, 2003

By J. L. van Niekerk, J. Gunaselvam

This study investigates the use of appropriate seating systems for the control of whole-body vibration exposure in vehicles used in the SA mining industry. Six suspension seats were tested with six test subjects to determine the most suitable seat for an articulated dump truck based on the EM1 requirement in ISO 7096 (2000) standards. Transmissibility functions were measured in the laboratory using the newly commissioned Dynamic Seat Testing Facility with two excitation levels of 1m/s2 and 2 m/s2 r.m.s. in the 0.5 - 30 Hz frequency range. SEAT values were calculated for two input spectrums, the EM1 input spectrum specified as in ISO 7096:2000 and measured road vibration data measured on a typical articulated dump truck. The averaged SEAT value calculations indicated that not one of the seats will qualify as an ISO 7096 (2000) suspension seat but that it is possible to select a seat that will significantly reduce the vibration the driver will be exposed to.

Jan 1, 2003

By X. B. Zhao, J. G. Cai

The purpose of this paper is to incorporate the dynamic BB model of rock fracture normal behaviour into Universal Distinct Element Code (UDEC), and to conduct UDEC modelling to predict stress wave propagation across rock fractures. With the incorporation of new dynamic model of fractures, the UDEC is improved in the capability of modelling wave propagation across fractures. In this study, the case of normally incident P-wave transmission across a fracture is modelled, and the effect of dynamic normal behaviour of fracture is concentrated on. Wave transmission coefficient for wave transmission across the fracture with the dynamic BB model is obtained for various combinations of fracture dynamic parameters, as well as different wave amplitudes and frequencies.

Jan 1, 2003

By A. Tor, M. Borowski, N. Szlazak, D. Obracaj

This article presents possibilities of reducing methane emission to the atmosphere in working mines in Jastrzebie Coal Company by means of proecological solution. They form a new approach towards the problem of rational and effective use of natural resources both in economical and environmental respect. Power and thermal energy for underground air conditioning in mining excavations are produced from the methane, which is drained out of the mine for safety reasons.

Jan 1, 2003

By Willem Le Roux

The common law requires an employer to take reasonable steps for the safety of employees. In general, the duty of care means that the employer, acting personally or through its employees or agents, must take reasonable care for the safety of its employees (Van Deventer v Workmen?s Compensation Commissioner; 1962 (4) SA 28 T; Oosthuizen v Homegas (Pty) Ltd 1992 (3) SA 463 T).The duty of care includes the provision of safe premises, safe machinery and tools and a safe system of work. The obligation is not an absolute one, but is restricted by the concept of reasonableness. The common law duty may, in certain cases, include the assessment of hazards and risks. 2 International law Great emphasis has been placed in the Western world on the prevention of occupational diseases and injuries. Detailed statutes and regulations govern specific industries in many countries. See, e.g. the Control of Substances Hazardous to Health Regulations of the United Kingdom and various regulations applicable to the use of asbestos and lead, fire protection, mines and quarries, petroleum, etc. Risk management is an important part of managing health and safety. In the United Kingdom, the Management of Health and Safety at Work Regulations, 1999, require every employer to make a ?suitable and sufficient assessment of the risks to health and safety of his employees to which they are exposed whilst they are at work?. The particularity of the assessment is determined by the risk in question.

Jan 1, 2011

By T. Gerritsen, A. Matyas, F. Stober, I. Candy

This paper describes developments in ferro-nickel furnace technology, specifically improvements to cooling methods, furnace controls, and high voltage furnace operating regime. The evolution of these technologies is briefly presented, as context for describing the current state of the art that has enabled ferro-nickel furnace operation at over 75 MW and specific energy consumption of less than 400 kWh/t dry ore. Examples from existing operations are used to illustrate present best practices, and potential future trends are discussed. The paper begins with an overview of the fundamental aspects of pyrometallurgical treatment of lateritic ores that drive ferro-nickel furnace design. Furnace wall cooling methods are related to the requirements resulting from specific furnace process conditions, including slag and metal compositions, as well as arc and bath power. The benefits of high productivity and low specific energy consumption resulting from high voltage (shielded-arc) operating practice are discussed, along with the furnace controls and electrical power train that enable such operation even with captive power generation.

Jan 1, 2004

By M. Olper

The zinc recycling is assuming more and more importance. A lot of zinc secondaries and wastes are ready to be collected and converted to zinc metal. The impurities present in these materials and the technical and economical problems that some traditional ways of treating these materials are facing, call for new technologies. The EZINEX Process, a fully hydrometallurgical process industrially proven to convert oxidised zinc bearing materials directly to zinc cathodes, is an innovative process that can deal with any kind of zinc waste/secondaries in a very powerful way. In this paper the highlights of this process will be shown and discussed to demonstrate the robustness of the process and its economic viability.

Jan 1, 2008

By W. Barthel, B. A. Dippenaar, J. Malan

In its most basic form, the process of sintering is very simple, and has been in use since the turn of the previous century. However, while the basic process is simple, control of the process relies on a number of extremely complex interdependent process parameters and requires a thorough understanding of the effect of these parameters on production capacity and product quality. Further, as with many other processes, the process parameters and hence design details of visually similar installations are highly dependant on the specific feed materials. While the industry trend has been towards an increase of capacity in order to lower unit production cost, typically in Iron ore sintering plants, this approach is not always possible for other commodities because of the scale of operation. This paper seeks firstly to describe some design considerations of sinter plants; secondly, to report on results from testwork performed with a specific series Manganese ore blends; and last, to relate these results to the design of new small-scale Manganese ore sinter plants.

Jan 1, 2004

By S. Sridhar, R. E. Aune, M. Hayashi

Thermophysical properties of silicate melts are strongly structure dependent. It is well known that the viscosities of slags increase with increasing the degree of polymerization of silicate anions. Even the thermodynamic properties of slags are dependent on the types of species and the population of the same in the melt. Thus, a link between the thermophysical and thermochemical properties of silicate melts is logically expected. The present paper elucidates the salient features of Darken?s excess stability approach to the Gibbs energies of solutions as applied to the viscosities of silicate melts. It is demonstrated, that the second derivatives of the viscosities of binary silicate melts with respect to composition indicate a maxima corresponding to the existence of stable compounds in these systems. The concept was successfully applied to the following systems: Al2O3-SiO2, CaO-SiO2, FeO-SiO2, MgO-SiO2and MnO-SiO2. In all the cases, the second derivative plots of viscosities with respect to composition showed peaks corresponding to the metasilicates. The second derivatives of the activation energies of viscous flow with respect to temperature has earlier been shown to reflect the formation of associates/embryos in the homogeneous silicate melts, indicating the readiness of the melt to separate a solid phase. Thermodynamic coupling of thermal diffusivities in the case of the system CaO-Al2O3-SiO2from the laser-flash measurements of these slags as a function of temperature are examined as part of the present study. Densities are estimated from integral molar enthalpies in the case of silicate systems and the results are presented. Keywords: silicate melts, viscosity; activation energy, thermal diffusivity; density

Jan 1, 2004

By Z. Jin, Q. Yun, C. Lu

This paper presents a quantitative assessment model for the assessment of environmental load in gold production, which is based on environmental ecology, Life-Cycle Assessment and technical conditions of gold production in China. This model can make environmental assessment in terms of a set of indexes and quantitative approach by means of artificial neural network, which also improves the theory of Life-Cycle Assessment. Keywords: Artificial neural networks, Environmental load, Assessment, Utility function, Gold production

Jan 1, 2003

By S. Marsland

Reference materials have always been important for validating and controlling analytical methods. They have recently become even more important as quality requirements have become more stringent and customer demands for properly verified and controlled results increase. Clients, especially from the resource exploration industry, demand critical validation of all results reported. Mintek has been producing geological and semi-processed ore references since the early 1970s and recently, due to increase in demand, other manufactures have entered the South African market. This paper describes analytical challenges from the customers? perspective, the customers being metallurgists, mine geologists, environmental scientists and geologists from resource companies. Reference materials with their appropriate use and a good understanding, can aid greatly in building confidence in the results, choosing the right laboratory for a project, deciding which set of results is correct and providing evidence to the customers? clients that the best possible results have been obtained

Jan 1, 2007

By F. Crundwell, A. J. Lathwood

A number of base-metal operations would like to increase production to take advantage of the higher metals prices. In general, this higher production should not be achieved with major operating changes. In hydrometallurgical facilities, leaching and pressure leaching represents one area where upfront limitations may be a bottleneck to the capacity of the entire plant. An assessment of the capacity of the leaching tanks and autoclaves was performed using a predictive model within the AweSym flowsheet simulator. The model is described, and the results of the application of the model to a number of different leaching reactors are presented. It is argued that the leaching number, which relates the residence time, particle size and the leaching rate, is of prime importance. Finally it is shown that there are some unexpected catastrophic events in increasing production capacity without a thorough understanding of the leaching operation.

Jan 1, 2007

By P. Sharma, J. C. W. Fowler

This paper discusses the wind blast / air blast phenomenon, how it is managed in coal mines and how it might best be managed in other underground mines. L'article qui suit a pour objets de décrire le phénomène de tir a l'air comprimé et les méthodes de modération de celui-ci dans les mines de houille, et d'indiquer de quelle manière il pourrait être surmonté dans d'autres mines souterraines. Dieses Seminararbeit diskutiert die Windexplosion / Luftexplosion Phänomen, wie es in Kohlenberg-werken geleitet wird, und wie es am besten in anderen untertage Bergwerken geleitet werden könnte.

Jan 1, 2003

By Deon van Tonder, Bert Van Hege

Comparison of various technologies for uranium recovery from sulphuric acid leach solutions shows that Resin-in-Pulp (RIP) and/or Solvent extraction (SX) based processing routes are usually cost effective (11). A combined RIP-SX recovery-purification route and a CCD-SX recovery-purification route were investigated and optimised. The design basis used for the investigation was a production rate of 200 kg/h U3O8 over a solution concentration range of 40 to 1500 mg/L U3O8. The OPEX for the RIP-SX processing route was found to be sensitive to the variation in uranium concentration in the leach liquor. One of the main drivers for this trend is the leach acid concentration. Conversely, the CAPEX of the CCD-SX processing route was sensitive to the uranium concentration in the leach liquor. The leach acid concentration only affected the OPEX of the CCD-SX processing route modestly, as the bulk of the acid is recovered in a pre-leach circuit. Contrary to expectation, the effect of extractant loss assumptions on the overall processing route economics was found to be modest to insignificant. It should be noted that the CCD-SX processing route OPEX was more sensitive to extractant loss assumptions than the RIP-SX processing route OPEX. Economic optimum wash ratios were determined for the CCD-SX processing route and increased with leach concentration ? the increase in wash ratio was less than proportional. A 5-stage CCD configuration was found optimal over the concentration range investigated.

Jan 1, 2007

By P. Sun

Abstract: From the viewpoint of interaction mechanics of solid and gas, a coupled mathematical model is presented for coal/rock mass deformation and gas leak flow in parallel deformable coal seams. Numerical simulations for the prediction of the safety range of mining of protection layer are performed with experimental data from a mine with potential danger of coal/gas outbursts. Analyses show that the numerical simulation results are consistent with the measured data on the spot. Therefore, the coupled model shows a positive future for applications in a wide range. ZUSAMMENFASSUNG:Von der Veranschaulichung der Abhängigkeit Mechaniker für Körper und Gas, wird ein verbundenes mathematisches Modell für festen coal/rock Deformation und Gasleckstelle Fluß in parallele deformable Kohlenähte dargestellt. Numerische Simulationen für die Vorhersage der Sicherheit Strecke, die Schutzschichtbergbau verwendet, werden mit experimentellen Daten von einer Grube mit möglicher Gefahr der coal/gas Ausbrüche durchgeführt. Analysen zeigen, daß die numerischen Simulation Resultate mit den gemessenen Daten bezüglich des Punktes gleichbleibend sind. Folglich zeigt das verbundene Modell eine positive Zukunft für Anwendungen in einer breiten Strecke. RÉSUMÉ: Du point de vue de la mécanique d'interaction pour le solide et le gaz, un modèle mathématique couplé est présenté pour l'écoulement plein de déformation de coal/rock et de fuite de gaz dans les filons houillers deformable parallèles. Des simulations numériques pour la prévision de la gamme de sûreté employant l'exploitation de couche de protection sont effectuées avec des données expérimentales d'une mine avec le danger potentiel des accès de coal/gas. Les analyses prouvent que les résultats numériques de simulation sont conformés aux données mesurées sur place. Par conséquent, le modèle couplé montre un futur positif pour des applications dans un éventail.

Jan 1, 2003

By E. Wolmarans

Dowding, Reynard and Associates Mineral Projects (DRAMP) was approached by the ARM/Lion Ore JV during July 2006 to conduct a feasibility study and control budget estimate for a new greenfield project for their NKOMATI Nickel mine 45 km east of Machadadorp. The scope included the evaluation and review of previous studies as well as a techno-economic trade-off on four possible comminution circuits ranging from conventional crushing and ball milling to fully autogenous milling. The following document encapsulates the thought process, decisions and the references used in selecting the final comminution route for the new 375 ktpm MMZ concentrator. Apart from the pilot test work performed, design simulations from a number of sources, performance results from a recently commissioned 100 ktpm MMZ concentrator, together with an understanding of the geology and mineralogy of the orebody and possible variations in the characteristics of the orebody over the life of mine were assessed. The results from all the above-mentioned work indicated that it would be possible to treat the MMZ ore at the desired throughputs to the desired grind sizes in a fully autogenous grinding (ABC-type) circuit. Autogenous milling is generally considered to be one of the higher risk milling circuits. This is mainly due to the fact that the ore, which is utilized as the grinding media, could be variable in terms of hardness and mineralogy/geology. Nevertheless, it is a very popular route as the cost benefits, more specifically the operating cost, are normally very attractive. This is especially the case when large low grade orebodies are evaluated. In North/South America, autogenous and semi-autogenous grinding circuits have been successfully employed during the past 20 years on large scale low grade operations. Taking all the above factors into account, the DRA/Nkomati project team recommended an autogenous circuit with the option to add steel to both the primary and secondary mills (if required) for the new operation in order to create the opportunity for significant operating cost savings. One has to bear in mind that all the new design simulations and decisions are based on previous work and potential unknown variations within the orebody will never be fully understood until the pit is operational for some time.

Jan 1, 2009

By N. A. Barcza

This publication records the proceedings of the Tenth International Ferroalloys Congress, INFACON X, and the third INFACON hosted in South Africa. The Proceedings of the previous two South African congresses in 1974 and 1992 serve, as this volume does, as a valuable record of the papers presented at these important events. This publication comes at a time in South Africa?s democratic development where the theme ?Transformation Through Technology? is very appropriate. The ferroalloy industry has played an increasingly significant role in transformation and black economic empowerment in South Africa, particularly through the advancement and sharing of technology. INFACON X plays an important role in this process, and the stakeholders and organisers of this Congress are thankful for the opportunity to hold this event at this time of transformation in our country. The world of ferroalloys, as well as that of the steel and stainless steel industries, has continued to change rapidly. Recent innovations, better use of resources, increased awareness of environmental issues and ongoing efforts to improve occupational health and safety are among the topics addressed at INFACON X and in these Proceedings. The theme of ?Transformation Through Technology? has been chosen to reflect the regional and global developments in the ferroalloy industry, and the crucial role that technology plays. The Proceedings of INFACON X, the first Congress in Southern Africa of the new millenium, represent a milestone in the technical developments in this major global industry. It contains almost eighty papers in twenty Sessions, from authors in twenty countries, covering raw materials, reductants, energy, electrodes, refractories, furnace design, post taphole services, modelling, simulation, control, sensors, fundamental issues and the applications of ferroalloys as related topics. The major ferroalloys, namely ferrochromium and ferromanganese, are covered extensively in many interesting papers. This comes as no surprise, since South Africa is the leading producer of ferrochromium and also plays a major role in the supply of manganese ore and alloys. Papers on ferronickel, silicon and ferrosilicon ensure that all the large-volume ferroalloys are addressed. These Proceedings of refereed papers of high quality will serve the ferroalloy industry for many years to come, as has been the case with previous INFACON events. For the first time in the history of INFACON, the Proceedings will be available both in bound and in a searchable electronic CD-ROM format. We appreciate the time and effort that the authors and referees have devoted to making this publication a really valuable document. Their contributions are recorded for posterity and reflect the advancements they and their colleagues have made to benefit the ferroalloy industry. Without these ongoing improvements, the industry would stagnate and not fulfil its role in the advancement of mankind. All papers included in these Proceedings were peer-reviewed by at least two referees. About 130 referees were sourced internationally to fulfill this function, and their valuable technical and editing inputs are gratefully acknowledged. Finally, I would like to thank the Technical Programme and Publication committees, led by Dr. Lloyd Nelson and Dr. Noël Machingawuta respectively. Without the tireless efforts of these individuals and their Committee members, the technical programme and these Proceedings would not have been the success they certainly are.

Jan 1, 2004

By A. C. Moorgas, J. Divall

This study investigates the feasibility of using waste iron slag, the by-product from a mineral sands processing works, in road construction. The study includes the different options investigated for the treatment of a leachate that is produced during the cooling of the iron slag, prior to processing. It also reviews the reasons for choosing the current treatment option that is being trialed. Cooling the iron slag with water results in the formation of a leachate with a high pH and high sulphide concentration. This leachate can seep into the ground and, over time, it will contaminate the ground water. A system was designed to collect and treat the leachate to prevent contamination of surrounding natural water sources. Numerous leachate treatment options were investigated to find cost effective method of treatment After cooling, the iron slag is passed through an iron recovery plant and the unsaleable product is placed on a dumpsite. Rain percolates through the dumpsite, which can result in the formation of a leachate that can contribute to a contaminated plume. After extensive testwork, it was found that the dumpsite, which was leached of contaminants, could be screened and used as a G5material (specifications in Table II) in road construction. The initial challenge was to establish that this material was environmentally safe for use in this particular application. Approval from the Department of Water Affairs (DWAF) was required for the testwork and then for the long-term use of this material in the construction industry. The following challenge involved establishing a market for the material. Construction companies in the area were reluctant to change to a new product that was not naturally occurring. The economics of this project are extremely sensitive to transport costs and hence only projects within a specified radius can be supplied with the Black Top Gravel (BTG). This project is not are venue generator, but it does save the money that would be required to manage the dump, and it reduces the closure costs.

Jan 1, 2003

By S. Erçayhan, B. Derin, O. Yücel

In the present study, the production of low carbon ferrochromium (LC-FeCr) from chromite concentrates containing 55.09% Cr2O3 and 13.06% Fe via metallothermic process was investigated. For this aim, in the experiments, the aluminothermic reduction method was applied in an open crucible. 10% CrO3 + 10% NaClO3, 15% CrO3 + 5% NaClO3 and 20% CrO3 by weight of concentrate were added to the charge, respectively and the charge was reduced with aluminium. The experiments were done with the additions of 90, 100, 110, 120 and 130% of stoichiometric requirement of aluminium. The highest Cr content in alloys was found as 71.7% at 120% of stoichiometric Al whereas the highest Cr recovery in alloys was found as 71.8% at 130% of stoichiometric Al when the both charge contained 15% CrO3 + 5% NaClO3 by weight of chromite concentrate.

Jan 1, 2004

By R. Zivojinovic, S. Vujic

The structural age of the capital mining machinery, representing a part of the system of the Electric Power Industry of Serbia, has been dictated by the initiation and development of open pit coal mines. For example, the oldest bucket wheel excavators were installed some thirty-four years ago, and the average life of the relevant machinery exceeds twenty-two years. Operation of both capital equipment and machinery has direct effects on economic and business activities of open pit mines, and consequently forced us to make a decision and study thoroughly the problem of establishing the optimum exploitation life of capital mining equipment at the open pit coal mines of the Electric Power Industry of Serbia. The aim of this paper is to define and discuss the relative problems as well as to find out the possible solutions and establish the methodology for estimating the optimum exploitation life of machinery. The study was successfully carried out by a team of scientists engaged from and coordinated by the Department of Computer Science of the Faculty of Mining and Geology, University of Belgrade. This paper presents the key observations covering the subject problem. Keywords: Mining, Opencast exploitation, Coal, Optimization, Exploitation life, Capital machinery, Electric power industry, Dynamic programming.

Jan 1, 2003