Search Documents

By J. E. Pahlman

One of the goals of the Bureau of Mines is to develop metallurgical pro-cesses that conserve energy and/or that take advantage of abundant domestic energy sources. Western lignites and subbituminous coals can be used for firing pellet induration and metallization furnaces. However, the refractory linings of these furnaces must be able to withstand attack from corrosive alkali metal oxides present in the ash of many of the low-rank fossil fuels. The Bureau of Mines conducted dynamic and static slag tests on high-alumina and alumina-silica refractories to determine their resistance to lignite ash slags. The investigations showed that increased alkali content in the lignite ash caused increased corrosion and erosion of the tested refractories. The degree of corrosion decreased with increasing alumina content, with the 99-percent-alumina refractories having the highest resistance. In general, the matrix phase was attacked preferentially to the alumina grains. Also, porosity reduction and tar impregnation enhanced the corrosion and erosion resistance. The 90-to 99-percent-alumina refractories are recommended for use as furnace linings in alkali slag environments.

Jan 1, 1979

By H. A. Tucker

This Bureau of Mines investigation was conducted to determine the appropriate quantities of rare-earth methals (REM) in the form of silicides to add to an alloy steel for the purpose of increasing toughness and ductility. The work was conducted in a vacuum induction furnace with the rare-earth additions required to deoxidize and desulfurize a simulated basic oxygen furnace (BOF) vacuum-degassed steel initially containing 0.013 to 0.016 percent sulfur. The product proved to be as good or better than the best basic electric furnace steel of the same composition made by the steel industry. Twenty-three experimental heats of 5 Ni-Cr-Mo-V steel were made, cast into 50-1b ingots, and hot-worked in a press and a rolling mill to ½ inch plates which were then heat-treated to 130/150 ksi4 yield strength. Impact and tension tests showed that the addition of 0.025 to 0.100 percent, or ½ to 2 lb per ton, respectively, of rare-earth metals when compounded with silicon were appropriate for increasing toughness and ductility. These quantities resulted in retained cerium contents between 0.014 to 0.025 percent, and increased the Charpy V-notch energy absorption and the percent reduction of area significantly as compared with base heats at the same sulfur content levels. All the test heats, including those with additions of REH of as much as 4 lb/ton, had greater Charpy V-notch energy absorption values than the base composition could have developed at the starting sulfur range of 0.013-0.016 wt pct.

Jan 1, 1968

By G. V. Sullivan

This report describes an investigation by the Bureau of Mines of flotation techniques for the recovery of chromite from fine-grained disseminated ores. Reported work on the concentration of chromiferous materials shows that flotation has been applied almost exclusively to slime-free pulps. Therefore, chromium recoveries that could be obtained by flotation were related to the amount of slime rejected. However, results of recent studies by the Bureau of Mines showed that des liming is not a requisite to selective concentration of chromite. Laboratory-scale tests on seven ore types from the more important chromium-bearing areas of the Pacific Northwest showed flotation to be technically feasible for treatment of all but one of the samples. Concentrate grades were affected more by the composition of the chromite mineral than by the grade or character of the ore. Test results from three of the samples showed that, without prior desliming of the pulp, 78 to 91 percent of the chromium could be recovered in concentrates of 90 percent or more chromite; two samples responded to similar treatment, resulting in concentrates of more than 80 percent chromite with recoveries of 85 and 89 percent chromium. One sample of mill products, subjected to severe weathering, required removal of the primary slime to obtain a concentrate of 65 percent chromite with only 75 percent chromium recovery.

Jan 1, 1960

To develop and design a bit that will rapidly drill smooth and precise instrumentation holes in soft rock. Approach Use a one-piece bit made by combining a drag bit and a diamond bit. Because a smooth-walled borehole with a precise diameter is needed for borehole pressure cells (BPC) and other borehole instruments, a diamond bit is usually used. However, diamond bit drilling is slow, and the bit will tend to bind when squeezing ground is encountered. On the other hand, the drag bit will cut faster, but the walls of the drill hole will be rough and the diameter will not be as precise. The combination will provide a bit which penetrates as rapidly as a drag bit, but retains the smooth-wall and precise borehole diameter of a diamond bit. How It Works A three-foot-length of EW-size drill rod is centered in a diamond bit by welding it to three equally-positioned spacers at each end of the bit. A drag bit is attached to the EW rod with a standard EW-to-drag bit adapter as shown in the diagram. Three equally-spaced diamond inserts are set to the desired hole size and welded to the diamond bit barrel behind the crown. These inserts increase the smoothness and precision of the hole by cut-ting away any hole closure. Three equally-spaced shims are set approximately 0.020-inch under the overall insert diameter size and welded to the rear of the diamond bit barrel. The combination bit should be used on a diamond drill with either water, mist or air as the coolant.

Jan 1, 1982

By Jack C. White

Studies were made to determine the character and distribution of the copper lost in copper mill tailings. Acid soluble (oxide) and acid insoluble (sulfide) copper were determined for heavy-liquid sink and float products of screen-sized fractions from 12 copper mill tailings. In most of the tailings studied, the coarse-size fractions are higher in copper grade than the respective bulk tailings, high in sulfide copper, and low in oxide copper. Oxide copper occurs predominantly in the minus 325-mesh "slimes." Microscopic examination of heavy-liquid sink products indicated that recovery of liberated copper sulfide minerals is complete in most mills, and that copper minerals not being recovered are locked with gangue particles. Additional copper could probably be recovered from most tailings by size classification, scavenger froth flotation of the coarse fraction, and regrinding of the concentrate to achieve liberation of the locked sulfides.

Jan 1, 1971

By J. G. Walters

The method for predicting coke strength developed at Steinkohlenberg-bauverein, Germany, in which experimental parameters are readily determined by small-scale laboratory tests, was found to be applicable to cokes produced from industrially used blends of American coals. Predicted 1-inch ASTM tumbler indices for four industrial blends were found to be in excellent agreement with the experimentally determined values. The laboratory determined prediction parameters include the proximate analysis of the coal the size consist of the coal, and Ruhr dilatometer test data.

Jan 1, 1971

By John Nagy

The Bureau of Mines examined explosion development in a closed spherical vessel, mathematically correlating flame travel, pressure, and time with parameters defining the reaction. The model assumes that burnt and unburnt zones are separated by a thin, radially moving flame front. Isothermal and adiabatic systems are considered. Correlation with gas and dust explosion data is better for the adiabatic system, but the isothermal development is simpler and in reasonably good agreement. Interpretation of the explosion phenomena is facilitated by expressing the rate of mole change in the flame front in terms of elementary parameters. This expression is developed by examining the components of spatial-flame velocity.

Jan 1, 1969

To perform comprehensive economic evaluations on both existing and proposed mineral operations. Approach A comprehensive computer model was developed which is capable of evaluating the economics of an entire mineral recovery operation, including exploration, acquisition, infrastructure, mining, milling, smelting, refining, transportation, taxation, and return of and on capital. How it Works The MINSIM (MINe SIMulator) economic evaluation concept was developed by the Bureau of Mines in 1967. The initial versions used a continuous discounted cash flow rate-of-return (DCFROR) to measure the effect of changes in expected revenues and costs. Subsequent enhancements to the program have expanded and strengthened MINSIM, especially the addition of an option which determines total production cost (i.e., the commodity selling price that a mineral recovery operation would require in order to obtain a target rate of return), an expanded capacity for evaluating by-products from a mineral property, and significantly broadened taxation determining capabilities. The MINSIM computer program uses essentially the same procedures and calculations that are performed in a manual economic evaluation, although the program accomplishes its tasks much more rapidly and accurately, An experienced mineral economist may require a week to evaluate a single mining operation with the same detail and consistency provided by MINSIM in a matter of seconds of computer time.

Jan 1, 1983

By Gregory P. Cole, Jeffrey Shawn Peterson

The Pittsburgh Research center3 conducted research to study and improve electrical fault detection on coal mine direct-current (dc) trolley systems. A suspended trolley line delivers power at voltages of 300 or 600 V dc to the haulage equipment and other loads. Roof falls or other accidents may force the trolley line down so that an electrical fault current may flow between the trolley line and rail. This fault current could result in localized heating, arcing, and perhaps fire. Such faults are not always preventable by the existing circuit protection because the current magnitude is well below typical operating levels of the trolley system. The research discussed in this report studies the applicability of computerized signal analysis techniques to solve this problem. Tests were conducted at cooperating coal mines. Measurements were taken during normal loading of the trolley system (light, intermediate, and heavy traffic), during induced fault conditions (arcing and bolted faults), and during transitions between the two. These data were then used to train and test a microprocessor-based fault detection algorithm. Later, field tests of the detection algorithm found that it correctly classified the state of the trolley system greater than 95% of the time.

Jan 1, 1997

By C. D. Litton

Submicrometer particle concentrations and average particle sizes were monitored for four full-scale sealed coal fires in the multiple-entry section of the Bruceton Experimental Mine. The data from these tests indicate that there exists a very good correlation between the submicrometer particle concentrations and the maximum temperatures measured within the coalbed. As the maximum coalbed temperature decreases with time after sealing, the submicrometer particle concentrations show a corresponding reduction. This particle-temperature correlation is in sharp contrast to the gas concentration data obtained, for which essentially no correlation exists with the measured coal-bed temperatures. The results of these full-scale tests indicate that the measurement of submicrometer particle concentrations may be a more realistic approach to determining the status of underground sealed fire areas.

Jan 1, 1981

To quickly and more reliably measure the alignment and deflection of mine guides used to run skips and cages into a mine shaft. The Problem Conventional mine guide alignment measuring systems require the use of a plumb bob and tape measure. This method is not only laborious, but it is time consuming as well. Approach Aware of the drawbacks of the current measuring method, the Bureau of Mines designed a self-contained instrument system that can accurately perform vertical guide alignment and deflection measurements by remote control. How It Works The Bureau-developed instrumentation system, called the Guide Alignment Measuring System (GAMS), is based on conventional mechanical electronics using inclinometers and displacement transducers. The instrumentation system is attached to an operating skip or cage where it functions as a completely self-contained measurement system, operating in conjunction with nor-mal travel of the skip or cage. An on-board tape recorder or a mini-computer with memory can be used to record all telemetry.

Jan 1, 1987

To clean coal mine air by developing a low-cost scrubber suitable for belt transfer and similar applications. Approach Design a scrubber operated by water only, with no moving parts. Use conventional water spray nozzles located within a duct to both move and clean the air. Use a droplet eliminator to get the water droplets and mist back out of the airstream. How It Works Conventional scrubbers require a mechanical fan driven by either an electric or a hydraulic motor. They also require water sprays and some type of scrubbing mechanism. The water powered scrubber, however, offers higher reliability over conventional scrubbers since it utilizes the water sprays to both move the air and scrub the particulate from the air. Conventional water spray nozzles are placed near one end of a rectangular duct open at both ends. The sprays are directed towards the far end of the duct where a stationary wave blade water droplet eliminator is located. Movement of the water spray droplets coming from the nozzles generates (by momentum transfer) an air movement In the same direction as the sprays. The volume of air moved Is primarily a function of the duct cross-section size, water pressure and water

Jan 1, 1981

By James J. Olson

The Bureau of Mines recorded peak particle-velocity levels and vibration frequencies to determine the nature and intensity of ground vibrations for tunnel blast rounds at the NORAD Complex, Colorado Springs, Colo. Previous Bureau of Mines studies in quarries and underground mines had shown that scaling (dividing) the distance from the blast by the square root of the charge weight removed the effect of the various charge weights on vibration amplitudes. The analysis of variance tests performed on the NORAD vibration data, however, indicated that the cube rather than square root scaling exponent grouped the data more effectively. The empirical propagation equation, V = 560 (D/w1/3)-2.04, where V is the maximum peak particle velocity in inches per second, D is the distance from the blast in feet, and W is the zero-delay charge weight in pounds described the attenuation, with distance, of the particle velocities from the tunnel blasts in the Pikes Peak Granite of the NORAD Complex.

Jan 1, 1972

By James P. Bennett

To improve construction materials for emerging chemical and metallurgical technologies, the Bureau of Mines is investigating the acid resistance of ceramic materials. In the study described here, eight commercial ceramic materials comprising two red shale, two fire clay, a silica, a silicon carbide, a carbon, and a high-alumina brick were evaluated. Samples were exposed to 20 wt-pct HC1 at 50° C for 110 days. The test apparatus designed to evaluate the materials is described. Changes in chemical and mineralogical composition, cold crushing strength, volume, and weight, and leach rates of AI, Ca, Fe, K, Mg, Na, Si, and Ti ions were monitored. In general, the statistically significant physical property changes that occurred were small. In many cases, no changes were detected.

Jan 1, 1982

By S. J. Hussey

A jig tailing with gold content ranging from 0.33 to 0.43 oz/ton was leached in weak cyanide solution with extractions of up to 97 pct in 24 hours. By countercurrent batch leaching studies and laboratory pilot plant operation, minus 10- plus 20-mesh and minus 6- plus 16-mesh coconut carbon were loaded to 700 oz/ton of Au. Minor silver in the ore reported in the carbon in amounts of up to 100 oz/ton. Gold adsorption rate data and an equilibrium adsorption curve for minus 10- plus 20-mesh carbon at ambient temperatures were developed and used in the successful application of a cascade design theory. The work was performed as a part of the overall Bureau of Mines research effort to help maintain an adequate domestic supply of metals by making improvements in mineral-processing technology.

Jan 1, 1979

By John J. McClelland, Gerald T. Homce, John R. Thalimer

The U.S. Bureau of Mines has investigated the early detection of insulation failure in squirrel cage induction motors for the past 4 years. Research was done using a sophisticated empirical data-modeling technique based on values calculated from a motor's voltage and current phasors. This technique produces two polynomial equations that calculate the insulation leakage current and power. These models were implemented in a prototype system that monitors six motors on a continuous miner for insulation leakage. These insulation leakage values are used to anticipate insulation failure. The system consists of a motor-data-system for each motor on the machine and a control computer located away from the miner. Each motor-data-system consists of an analog interface to the motor's voltages and currents, a single-board computer that reads digitized data and calculates voltage and current phasors, and a bus node that interfaces the single-board computer with the rest of the system by way of a serial bus system. Using this bus system, the control computer requests and receives phasor data from the motor-data-systems. From these data the control computer calculates and displays two deterioration values for each motor, for leakage current and power, using Bureau-developed models. These values are stored in a data base from which the user can display graphs of each motor's deterioration values over time.

Jan 1, 1992

Improve transmission of data from an underground mine monitoring system to a remote, mass-data storage system. Background Instrumentation systems in underground mines must operate under environmental extremes of dust and humidity, local electromagnetic/radio frequency (EM/RF) interference fields, and potentially explosive atmospheres. During a recent roof-bolt study performed by the Bureau of Mines, it was necessary to transmit a large quantity of data to a data storage system. Conventional wire cable transmission presented several limitations which often required special electrical isolation or physical protection. Because conventional wire cable presented certain problems, the Bureau of Mines investigated alternative means of data transmission. The research investigation led to the selection of fiber optic cable for data transmission applications. The fiber optic method of data transmission offers several advantages: ? Since the transmission medium consists of light waves, it is safe to use in gassy mines. Where applicable, MSHA permissibility standards for peripheral devices must be met. ? It is lightweight and rugged. ? It can operate up to 131000 feet (4km) without repeaters and without EM/RF field interference.

Jan 1, 1986

By R. L. Grayson, S. S. Peng

"Research has been conducted during the past year on a study to correlate respirable coal mine dust characteristics with worker positions and coal seams. The first characteristic of respirable coal mine dust which has been addressed in the correlation study is respirable dust mass concentration. In fulfillment of this objective, two mines operating in different coal seams have been selected for respirable dust mass sampling on both longwall panels and continuous mining sections. At present, sampling has been completed on the longwall panel operating in the first mine, and one half of the planned sampling has been accomplished on the continuous mining section.The first mine sampled is operating in the Pittsburgh coal seam. The average mining height is approximately 78"" with an average of 8"" of bottom shale being mined. The mine is primarily a longwall mine, and continuous mining machines are used to support the longwall.Figure 1 shows the layout of the longwall panel which was sampled. Intake air is coursed via the track heading up to the headgate area. The air splits at the headgate. Approximately 20,000-30,000 cubic feet of air per minute (CFM) is used to ventilate the longwall face and about 5,000-10,000 CFM is routed down the belt entry. Substantial leakage across the gob was noted during the sampling period. An average of 1800 CFM per 100 feet of face leaked through the shields into the gob from #1 shield to #112 shield. A substantial amount of leakage also occurred between the #1 shield and the solid rib of the headgate development panel. The path of the air used to ventilate the panel is shown with arrows in Figure 1. Direction of air flow was opposite to the coal moving direction on the armored face conveyor.A double-drum ranging shearer is used on the face to cut a 30-inch web of coal. Normal practice is to cut from the tailgate to headgate with the leading drum raised and the tail drum lowered for cutting bottom. After reaching the headgate, the shearer is reversed and both drums are lowered for a clean-up pass. The last 40 feet of face on the tailgate is cut on the clean-up pass.The shearer is equipped with 2 banks of 4 water sprays each and 2 large sprays on the headgate end and 1 bank of 4 sprays on the tailgate end. Additionally, sprays are located above bits on the cutting drums. Actual cutting speed was approximately 14-18 feet per minute, depending on conditions.The cross sectional area for air flow on the face was approximately 60 square feet before a pass was mined and 80 square feet after a pass was mined but before the shields were advanced. The cross sectional area at the shearer was about 35 square feet.The condition of both the tailgate and headgate of the panel was good with no signs of significant roof problems. The roof conditions along the face during the sampling period were variable. At times, as much as 3 feet of drawslate fell from the roof for a span of as much as 40 shields. Generally, however, relatively local areas of falling roof were encoun-tered, usually limited to a 10-20 shield span when appearing.Ten days were spent gathering respirable dust samples on the longwall panel. Mine Safety Appliance (MSA) sampling units equipped with 10-mm nylon cyclones, pre-weighed MSA PVC filters, and constant-flow DuPont pumps were used to obtain thesamples. The pumps were calibrated at a 2 liters-per-minute flow rate. The 10-mm cyclone was selected for classifying total dust into the desired respirable fraction in order to obtain ""legally defined"" respirable dust samples for detailed physical characterization."

Jan 1, 1988

To rapidly and dependably locate shorts and opens in mining equipment power cables. Approach: The approximate locations of faults are found using a sound pulse echo, then the faults are exactly located with one of two probes. How It Works: To approximately locate u fault in shielded or unshielded cable, the cable is disconnected from the mine power center, and connected to the sound pulse generator. The generator is also connected to the ground conductor of the cable. When the generator is energized, electrical pulses are transmitted, and each moves along the conductor until it reaches a fault. When a pulse reaches the fault an echo returns to the instrument, either a positive pulse if the fault is an open, or a negative pulse if the fault is a short. See Figure 1. The further along the cable the first fault is from the instrument, the longer it takes for the echo to return. The instrument automatically measures the time and calculates the distance. The distance in feet is shown on an illuminated digital display.

Jan 1, 1976

By A. W. Effinger

The Bureau of Mines used regression analysis and applied statistical methods in an effort to rationalize the results of an experiment examining the effects of certain variables on carbon deposition in a reservoir for thermal recovery of petroleum. Although none of the 15 trials of the original experiment resulted in the response of weight-percent of carbon regarded by the experimenter as adequate, values calculated using canonical analysis in two trials yielded responses 33 and 54 percent higher than the minimum acceptable figure. The actual responses differed by less than 3 and 6 percent, respectively, from the predicted responses. Methods are described for defining a path of increasing response based on the minimum point and the response surfaces and for defining a set of values for the parameters in question, which result in increased response, A detailed explanation of the mathematical process used in this analysis is presented in the appendix for ease in computer programing the technique.

Jan 1, 1970