Search Documents

By Howard E. Parkinson

An environment monitoring and communication system has been installed in the Bruceton Mine, and research is under way to improve mine safety. Standard day-to-day mine communications are available, along with additional systems installed to permit experimentation with wireless radio, through-the-earth phones, along-the-roof paging, and mine face machinery communications. Research is continuing and the essential concepts for a dependable whole mine communication system, providing simple environment monitoring, improved day-to-day communications and post-disaster communications, will be demonstrated in a larger mine with about 900 feet of overburden.

Promote safer and more efficient mine operations by providing communications between personnel located anywhere in the mine. Approach A radio communications system was designed which takes advantage of existing mine wiring such as telephone lines or electric power cables. The existing wiring distributes radio signals throughout the mine, making communications possible between roving miners, vehicle operators, dispatchers, and other personnel. How It Works Research has shown that medium frequency (MF) signals (300 KHZ-3 MHZ) can couple onto and re-radiate from nearby conductors. This effect is known as parasitic coupling and re-radiation. In a mine, these conductors include electric power cables, control lines, telephone lines, trolley lines, as well as metal water and air pipes Since all underground mines require these conductors for normal operations, the necessary network already exists and expands automatically as the mine is developed. A radio communication system has been developed that uses the parasitic coupling and re-radiation characteristic of MF. Using this system, whole mine radio coverage can be achieved without the need to install or maintain communication lines. The system consists of mobile transceivers for roving personnel and vehicles, and fixed-location base radio stations and repeaters.

Jan 1, 1982

By G. G. Morgis, J. J. Forbes

"INTRODUCTION The greatly diversified and increased uses of beryllium and its con& pounds in recent years have focused attention on the health hazards incident thereto. The Bureau of Mines has a fundamental interest in safety and the elimination or reduction of health hazards in the mineral and allied industries, and it recognizes that serious hazards are inherent in the production and use of beryllium and its compounds. This circular presents a review of the literature pertaining to such health hazards but does not describe original research by Bureau personnel. Most of the bibliography has boon either quoted in part or abstracted in an effort to present information in a comprehensive and readable form.In reviewing the literature, differences of opinions wore recognized in the writings of the respective authors, but no attempt was made to evaluate such differences. This presentation was devoted strictly to reporting without editorial comment.SUMMARYAlthough beryllium was known to industry for about 150 years, its toxicity did not present any serious problems in the United States until the advent of World War II, when the increased use of this element and its compounds brought to light several toxicologic reactions occurring primarily in the lungs and skin of workers handling it. The pulmonary effects, characterized as acute pnoumonitis and chronic pulmonary granulomatosis in beryllium workers, are far more serious than the dermatological manifestations.The addition of beryllium to the list of toxic industrial metals has boon so recent that there is still some confusion in the clinical picture. Data on magnitudes of exposure likely to be responsible for the production of disease are not yet adequate. There appears to be no relation between the severity of exposure and the development of cases some of those having had severe exposure have not developed a reaction, whereas those having a slight exposure in some instances have developed a response."

Jul 1, 1950

By B. Dimitriades

Experimental work has been done to refine and to confirm an analytical procedure by which gas-liquid chromatographic (GLC) spectra are interpreted from retention time data alone. The rationale of this spectra interpretation technique involves whether or not a given peak invariably represents the same component or component mixture; if not, what factors influence changes in peak identifications. To answer these questions, peak-identification procedures, based mainly on the use of subtractive columns, were developed and applied to interpret GLC spectra of several exhaust (and fuel) samples.

Jan 1, 1972

By Robert C. Gabler

The extraction of metals from coal ash was investigated by the Bureau of Mines in an effort to produce a more environmentally acceptable waste and offset waste disposal costs with recovered metal values. The research was conducted in two steps: determination of the parameters that affect extraction of metals from coal ash and development of extraction-recovery procedures. Data obtained indicate that the major parameter affecting the extraction of metals from coal ash is the calcium content of the ash. Other parameters such as furnace type and operating temperature had much smaller effects on metal extraction. Two procedures were studied for metal extraction: an acid leach procedure for high-calcium ashes and a lime sinter-acid leach procedure for low-calcium ashes. An alumina product was recovered that, with sufficient washing, meets Hall cell specifications. The leach residues pass the EPA EP Toxicity Test and are thus nonhazardous wastes available for a variety of uses.

Jan 1, 1983

By Robert F. Holub

The Bureau of Mines has made a study of the magnitude of the variations of radon daughter mixtures, with the objective of determining whether these variations reflect the existing physical conditions in uranium mine atmospheres or if they are merely random or systematic errors. To accomplish this, many data have been plotted using a triangular graphing technique which shows that plateout affects RaA more than RaB or RaC, and that it is impossible to find simple correlations between working level ratios, radon daughter mixtures, and age.

Jan 1, 1978

By David R. Forshey

This Bureau of Mines report presents a quantitative theoretical analysis of a coupled gasdynamics-heat release system involving the kinetics of water condensation in and behind the rarefaction wave in a shock tube using the method of characteristics. The merger of characteristics to form a shock wave is included.

Jan 1, 1977

By A. L. Engel

This report describes laboratory-scale experimental treatment of six base-metal ore samples taken by engineers of the Bureau of Mines, Region II, while investigating ore deposits in California and Nevada. The information is of interest in developing the mining districts represented or when similar ores from other sources are being studied. Simple treatment methods were employed as far as possible. More complex treatments also were tried when necessary. The possibilities and limitations of the methods applied to the several ores are shown by the data herein reported.

Jan 1, 1960

To improve mining safety and efficiency by providing a practical way of detecting faults and channel sands that disturb coal seams. Approach A seismic system using a shallow blasthole has been developed and tested. How It Works A small shock is caused in a shallow hole, sending seismic waves through the ground. These waves are reflected from the top of the coal seam, acid are detected by a line of geophones on the earth's surface. Dampening of the seismic signals by channel sands and other discontinuities in the seam is detected and recorded. See Figure 1. The seismic shock wave can be produced by exploding small charges, dropping a weight, firing a gas gun, or actuating a vibrator. Depending on the soil cover, the shock is usually generated in shallow vertical holes about 10 feet deep. Hole depth depends on the soil mantle thickness because it is preferable that the seismic shock originate below that layer.

Jan 1, 1976

By K. D. Luxbacher

Understanding methane emissions in underground coal mines is critical for a safe and productive mine. In addition to reasonable estimation of initial coalbed reservoir parameters, it is also crucial that changes in effective stress due to mining and pore pressure reduction are taken into account due to their effects on porosity and permeability. Primary parameters for estimation of emissions or modeling of the mining environment for this purpose are porosity and permeability which can change dramatically as a result of stress redistribution associated with mining and gas desorption from a large coal volume. These parameters affect the emission rates and ventilation requirements, as well as water inflow into the working environment. Stopping leakage, on the other hand, is a secondary stress dependent factor in estimation of emissions, as convergence of the roof and floor strata, compromising the integrity of the stopping, may result in leakage, making prediction of ventilation requirements difficult. This paper aims to examine the effects of porosity and permeability changes of the coal seam on methane emissions in an underground continuous miner section. The models were developed and executed in a dynamic fashion to simulate an advancing section. Through this process, the changes of effective stress in coal, particularly their change paths, on porosity and permeability were incorporated into the models and methane emissions, concentrations, air requirements, water inflow and possible leakage from the stoppings were investigated using a conventional coalbed methane reservoir model.

Jan 1, 2009

Provide a simple and effective means of measuring mining-induced pressure changes in coal mine roof and pillars. Approach Develop a reliable, easy to fabricate and install borehole instrument which measures mining-induced pressure changes in pillars and in the mine roof. Ground pressures are monitored through use of aluminum platens coupled with d copper flat jack. How It Works The Bureau's instrument measures mining-induced pressure changes by transmitting strata pressure through the aluminum platens to an oil-filled borehole platened flat jack (BPF). Pressure in the flat jack is displayed on a gage located outside of the borehole. The instrument is in-stalled in the borehole by inflating the flat jack using a hand-held hydraulic pump. In addition, the platens have been designed to allow up to three BPFs to be installed in a single borehole, thus permitting pressure change measurements in more than one direction from a single borehole. Installation pressure is calculated on the basis of the estimated pressure exerted by the overburden and the percent of recovery after intial mining has

Jan 1, 1986

By C. W. Davis

"A copper-palladium-gold-silver ore is being mined at Salt Chuck, Prince of Wales Island, Alaska, from which a concentrate is produced that contains 40 to 50 per cent copper, and considerable amounts of palladium, gold and silver. There has been much difficulty in obtaining assays for palladium, gold and silver from the mine, smelter, sampler, and umpire that check within reasonable limits. While the results for copper content have not been unusual, the results for palladium have varied as much as 0c8 oz. on 3 oz. material, results for gold differed by 0.1 oz. on 1.6 oz. materials, and for a silver content of 7 oz., results differed by as much as 4.0 oz.The Bureau of Mines was requested to determine the causes of variation in the results of the different assayers, and to develop a satisfactory procedure for analyzing such ore.Three samples of concentrate were received for analysis, two small lots that had previously been assayed by the various laboratories, and one large sample. The large sample was dried and ground in a ball mill, put through a 150-mesh screen, and then returned to the ball mill for thorough mixing. The small samples were ground to pass a 150-mesh screen and then mixed on a mixing wheel.The large sample (No. 1) was analyzed by five different procedures, one of the small samples (No.2) by three procedures, and the other (No. 3) by two procedures (the two small samples being too small for further tests). The different procedures tried and the results obtained arc presented below. The samples of concentrate were from ore mimed and milled by the Alaska palladium Co. at Salt Chuck."

Feb 1, 1926

Develop a down-hole replaceable diamond core bit that will reduce overall drilling costs and increase total available drilling time per hole. Approach A one-piece diamond core drill bit of unique geometric shape has been designed, fabricated and field tested. The bit can be withdrawn (or replaced) from the bottom of the well-bore without removing the drill rods from the hole, saving a significant amount of non-productive drilling time. How It Works The replaceable bit system consists of two basic subsystems: the removable core bit, and the equipment necessary to replace the wornout bit without pulling the drill rods out of the hole. The geometric configuration of the bit is that of a one-piece diamond studded cutting element created by "slicing off" two parallel sides of a conventional diamond cone bit. This geometric configuration, along with some minor modifications to the outer core barrel, allows the bit to be rotated in two planes and, with the retraction-insertion tools, raised or lowered through the interior of the drill rods using a conventional wire-line system. For example, to retrieve the bit, a retraction tool is lowered through the drill rods using a conventional wire-line system and at the hole bottom, the tool automatically orients itself within the outer core barrel.

Jan 1, 1981

By Rollien R. Wells

THERE are two recognized methods of recording the state of the metallurgical art. One involves delineation of individual advances reported in the literature. This approach is used effectively in the excellent annual reviews published by some of the leading technical journals and in the technology sections of the individual commodity chapters in this volume. In an effort to more clearly indicate the current trend of metallurgical research and development, the authors of this chapter chose the method of discussing generally selected items of interest brought to their attention during 1959. Since technology cannot be confined by dates on a calendar, most of the items mentioned have been in the process of development for several years. No attempt was made to identify the sources of information used here. Material was drawn from many sources : Nonconfidential correspondence and conversations with authorities of the metallurgical fraternity, papers delivered at technical meetings, and articles noted in the technical press, including particularly Engineering and Mining Journal, Metal Progress, Journal of Metals, Mining Engineering, Industrial and Engineering Chemistry, Chemical Engineering, Chemical and Engineering News, Chemical Week, Materials in Design Engineering, Review of Metal Literature, the Canadian Mining and Metallurgical Bulletin, the Mining Journal (British), and the Journal of the Institute of Metals (British).

Jan 1, 1960

By Manuel Gomez

Prediction models were constructed for seam elevation, overburden, and sodium concentration for a lignite deposit in Ward County; N. Dak. These models were developed by mathematical-statistical techniques using surface coordinates as independent variables to permit interpolation between drill holes. The results suggest that sodium concentration in lignite may be predicted in advance of mining. This information is helpful to mine planning, specifically, in scheduling production to deliver a uniform product to existing powerplants.

Jan 1, 1970

By M. D. Schlesinger

Mercury exists in coal in minute quantities, but the large tonnages of coal consumed could represent relatively large amounts of mercury entering the environment. Limits have now been placed on the emission of mercury, and it is important that reliable analytical methods be available to the chemist. The Bureau of Mines has evaluated analytical techniques used by a number of laboratories; most used vapor phase atomic absorption as the final detection method. Neutron activation was used by some of the laboratories. All of the methods described could be applied, but they require careful manipulation to prevent loss or mercury contamination. In the samples analyzed the mercury content ranged between 0.05±0.01 and 0.4l±0.06 part per million.

Jan 1, 1972

By Michael J. Sapko, Eugene M. Bazala, Eric S. Weiss, Kenneth L. Cashdollar

The data presented in this report are the results, to date, of an ongoing Pittsburgh Research Center Disaster5Prevention research program on the explosion hazards associated with blasting operations in noncoal mines. Laboratory and experimental mine tests have shown that oil shale and sulfide ore dusts can be ignited given the proper predispersed dust concentrations, particle size, and kerogen or sulfur content. Methane (CH) gas may also4be present in deep oil shale formations and can pose a significant added hazard to underground blasting operations. The most common explosive used for blasting in oil shale had been ANFO, a combination of ammonium nitrate and fuel oil; blasting in sulfide ore had used ANFO and/or dynamites. Tests conducted at the cannon gallery at Lake Lynn Laboratory near Fair chance, Fayette County, PA, provided a means of evaluating the relative incendivity characteristics of new and existing explosive products. Three explosives—a pumpable emulsion-ANFO blend, a packaged water gel, and an emulsion blasting agent—exhibited low-incendive qualities compared with other more highly incendive products such as ANFO and some dynamites. Based on the data collected during numerous full-scale blasts in oil shale and sulfide ore mines, the low-incendive products significantly reduced or eliminated the ignition hazards while at the same time providing effective fragmentation of the rock. Based on the positive results from the gallery and field testing, low-incendive explosives, coupled with good blasting procedures, show promise in reducing dust and/or gas ignitions associated with blasting operations in oil shale and sulfide ore mining applications.

By Richard L. Unger

Equipment is the primary cause of injury in 11% of all mining accidents and a secondary cause in another 10%. Purchasers should select new equipment carefully to ensure that the machine incorporates good ergonomic design criteria that maximize the safety of their mine workers. One potential problem area is the workstation-the control center of the machine. Safety problems often occur when the workstation provides insufficient clearance or visibility to the operator or has controls that are difficult to reach. This is especially true for underground mines, where confined space is an issue. In reclined or stooped postures, operators will have less strength and agility and often experience reduced visibility. We have conducted and published much research in Human Factors design of mining machine workstations. This information is currently being compiled into a series of Human Factors design recommendation reports. The reposts dl cover many topics, including workstation layout, control design, seating, and visibility. Each topic has a list of basic or first principles of design. Understanding these principles is the key to designing or purchasing a workstation that is both safe and efficient. Following is a sampling of these main topics and first principles.

Aug 1, 1996

By James P. Rider, Jeanne A. Zimmer, Andrew B. Cecala, Robert J. Timko, Earle H. Andrews

Many different types of structures and materials have been used to build mineral processing facilities over the past few decades. Although the structure type and building material were not viewed as significant factors affecting the health of employees in these facilities when they were built, the National Institute for Occupational Safety and Health performed an evaluation to determine to what extent building types could impact respirable dust and noise levels. This report discusses the evaluation of three different types of product sizing silica sand structures: a masonry design, a steel-sided design, and an open structure design. The data obtained in this study indicate that the open structure design (no walls) was superior from both a dust and noise (health) standpoint compared to the other two structures. The open structure design should also be beneficial from a cost standpoint because of lower material and construction costs. Companies and design engineers should consider this open design when building new mineral processing facilities in climates where it could be applicable. Some companies may also want to consider modifying existing structures with a more open design to further reduce dust and noise levels. As the trend continues in lowering allowable dust levels for federal health standards in the U.S. mining industry, the open structure design may be an approach for some companies to consider for their operations.

Jan 11, 2006

By Seth C. Schaefer

The Bureau of Mines investigated thermodynamic properties of Mn304 (manganomanganic oxide) and Mn203 (manganese sesquioxide). The standard Gibbs energies of formation (?Gf°) of Mn304 and Mn203 from their lower oxides were determined with high-temperature galvanic cells using stabilized Zr02 (zirconia) as the electrolyte. Potential measurements were obtained for the cell Pt, MnO, Mn304//Zr0 2//02(g, 0.0112 atm), Pt, with the overall cell reaction 6Mn0(c) + 02(g, 0.0112 atm) = 2Mn304(c), where- 02 refers to indicated partial pressure of oxygen at the reference electrode. Similar measurements were obtained for the cell Pt, Mn304, Mn203//ZrO2//02(g, 0.0115 atm), Pt, with the overall cell reaction 4Mn304(c) + 02(g, 0.0115 atm) = 6Mn203(c). Equilibrium oxygen pressures for the Mn0-Mn304-02 and Mn304-Mn203-02 systems were measured and may be expressed for the respective systems as [23,400 109 P02 T + 11.91 (764.9 - 1,208.6 K) and log p02 = - 11,957 + 9.66 T (968.6 - 1,208.2 K),] where pressure (p02) is in atmospheres and temperature (T) is in kelvins. Standard thermodynamic properties of Mn304 and Mn203 were derived from these measurements and auxiliary thermodynamic data from the literature.

Jan 1, 1982