Search Documents

To reduce the possibility of injury to operators and damage to equipment caused by collision of mining vehicles during coal loading. Approach An energy-absorbing bumper was developed and tested underground on a continuous miner. How It Works The bumper, a long box-like weldment backed by five energy absorbers, is attached to a continuous mining machine by a hinge behind the cab. See Figure 1. When a shuttle car collides with the bumper, or when it is otherwise struck, the energy absorbers are compressed. This absorbs and dissipates part of the kinetic energy of the colliding vehicle, thereby reducing or eliminating its destructive effects. Each energy absorber consists of two chambers separated by a freely-moving piston. One chamber (Figure 2) contains hydraulic fluid. The second chamber contains a gas. When a collision causes the absorber to compress, the hydraulic fluid in the first chamber is forced past a metering pin and through an orifice. The hydraulic fluid then pushes against the piston, compressing the gas in the second chamber.

Jan 1, 1978

By M. M. Tilman

The Bureau of Mines conducted research to determine whether it is possible to substantially improve the fatigue resistance of lead sheet by means of surface coatings. Five types of coatings were applied to unalloyed chemical lead sheet. Flexural tests revealed that the best fatigue resistance was obtained with coatings of vacuum grease. Vacuum-grease coatings on unalloyed lead sheet resulted in fatigue resistance at least as good as that of the fatigue-resistant alloy Pb-0.04 Ca. Coated lead sheet was also tested in short-time tensile tests and in tensile creep tests. Tensile and yield strengths were increased by several of the coatings with only moderate loss of ductility. Creep resistance was also improved in varying degrees by most of the coatings. The Bureau also conducted research on the effectiveness of noise barriers by using sheet lead in combination with other materials. Noise barriers consisting of continuous-cast sheet lead with gypsum board were found to be effective and relatively inexpensive barriers.

Jan 1, 1978

Significantly reduce respirable dust exposures of longwall shearer operators when cutting out at the headgate. Approach As a result of Bureau research, a ventilation curtain is recommended to be mounted between the stage loader and the coal rib to more effectively prevent the ventilation air from blowing across the shearer drum as it cuts out at the headgate. Some mine operators already employ this method of reducing dust, but a vast majority do not. How It Works One source of extreme concentrations of respirable dust for longwall shearer operators is the shearer headgate drum as it cuts through into the headgate entry. As the drum cuts into the entry, it is exposed to the primary ventilation airstream. The high velocity air passes through and over the rotating drum, picking up large quantities of dust.

Jan 1, 1982

By S. E. Khalafalla

The Bureau of Mines has used colloidal solutions of magnetite in a magnetic field to segregate nonmagnetic materials such as nonferrous scrap metals and to concentrate precious minerals. Conventional magnetic separation relies on the inherent magnetic susceptibility of the material to be separated and may be designated as magnetic separation of the first kind the medium of separation rather than the separated particles are made magnetizable, a new system of gravity separation results. In this new magnetic separation of the second kind, a magnetic fluid rather than air or water acts as the separation medium. The same force that attracts magnetic objects in separations of the first kind also attracts the entire separation medium in separations of the second kind, thereby creating a reactionary force of equal magnitude in the opposite direction. This force, sometimes called the levitation force, can be made to segregate nonmagnetic particles in a flowing stream according to their specific gravity. The technique has been applied to segregate nonferrous metals from automobile and appliance shredders and mixed scraps. The system has also been used to upgrade diamondiferous jig concentrates from certain river gravels in order to facilitate the sorting and recovery of their diamond content.

Jan 1, 1981

Provide a portable crushing capability to keep conveyor haulage close to the working face and permit more efficient and safer ore handling in low headroom, hardrock mines. Approach A readily portable jaw crusher is used which meets machine size, feed rock size, product size, and throughput requirements for low headroom, hardrock mines. How It Works The crusher is mounted on wheels to expedite frequent moves and to allow crushing of mined rock or ore near the working face. The crushed product is then placed on conveyor belts that are ex-tended as the crusher is moved. Keeping crushing and conveyor haulage near the face minimizes the haulage distances for trucks and loaders. Loading and haulage of run-of-mine ore is frequently the highest operational cost in underground mines. These costs can be significantly reduced by use of a belt conveyor, which is a common practice in coal and other soft mineral mines. The new low-profile hard rock crusher gives the same advantage of extensive belt haulage capabilities to low headroom, hardrock mines. The low-profile crusher will accept feed up to 30 inches when operating under 11 feet of headroom. The headroom required for crusher operation was reduced by tilting the jaws, feeding the crusher horizontally, and placing the eccentric shaft at the back or in a horizontal plane with the jaws. Material is fed by an

Jan 1, 1981

Reduce shaft sinking costs and workers exposure to mechanical hazards, drill dust, blast dangers, and fumes. Approach Replace drilling and blasting by using a large, cab-mounted impact breaker suspended from the bottom work deck of the galloway. How It Works The pneumatically actuated impact breaker is positioned by an articulated boom con-trolled from an operators cab. The breaker delivers 2,000 ft-lb blows that fragment the rock at the shaft bottom. Mucking is accomplished by a backhoe bucket on an articulated boom mounted on the cab. See photograph. The mucked material can be removed either by dumping into a previously drilled borehole or by being lifted out in a muck bucket as shown in the drawing. Positioning of the breaker, rotating the cab around its vertical axis, and moving the cab support frame around the perimeter of the shaft are all controlled by one joystick. Separate controls position the mucker boom, which can be swung horizontally through a 180° degree arc towards either side of the cab. Because the cab can be rotated to any position around its vertical axis, and can also be moved in a horizontal circle around the shaft, virtually any position on the bottom of the shaft can be reached by the breaker and mucker.

Jan 1, 1981

Reduce the noise levels to which operators of double-drum longwall shearers are exposed without compromising the operational effectiveness of the shearer. The Problem Noise produced by double-drum longwall shearers can be harmful to machine operators. Typical noise levels at the lead-drum operator position range from 100 to 105 dBA, and Federal noise regulations allow only one to two hours of exposure per shift at these levels. Noise radiated by the shearer cutting drum is the primary contributor to the overall noise level. However, test of a noise-controlled cutting drum developed by the Bureau of Mines reduced the operator noise level to 95 dBA, thereby increasing the allowable operating time to four hours per shift. Approach The key design aspect of the noise-controlled shearer drum is its reduced vibration-al response to coal-cutting forces. Laboratory studies have shown that these forces are concentrated in the low-frequency region (500 Hz and below). Since the cylindrical core and the cantilevered I plate-like helix of the standard shearer drum are easily excited by these forces (natural vibration frequencies be-

Jan 1, 1985

By J. H. Perkins

The Bureau of Mines has conducted desorption work on fine coal particles at near atmospheric pressure. An apparatus Iris been developed that uses a capacitance manometer to measure desorption of methane from coal particles up to, 2 inches in diameter and pressures up to 1,000 psi. This will make it possible to duplicate the desorption process as it occurs in its natural underground environment.

Jan 1, 1969

Provide an accurate, simple, alternative means of evaluating the safety of mine electrical ground systems which has little or no negative impact on mine productivity. The Traditional Evaluation Method The Code of Federal Regulations requires all mines to safely ground their power systems to earth. Effective earth grounding reduces shock hazards to mine workers operating electrical equipment, protects equipment from damage by voltage transients, and provides a means of detecting and locating ground faults. Once an earth ground bed has been constructed, its level of resistance has traditionally been used to gauge the safety of the entire grounding system. Bed resistance measurements are normally performed using a ?fall of potential? technique with a current return electrode placed at a remote location, If the resistance measured is acceptably low, then the bed is assumed safe.

Jan 1, 1985

By R. E. Collom

The spontaneous explosion of charges of nitroglycerin placed in deep wells situated in parts of the Ranger and Caddo fields of North Texas has aroused considerable inquiry among operators end others as to the probable agency, or combination of conditions, which causes the explosion.The method now followed, under certain physical conditions of a well, of setting a charge of nitroglycerin and allowing it to explode spontaneously was discovered locally by accident. In certain deep wells where formations, overlying productive strata, cave upon withdrawal of casing, it has been the practice to fire the shot electrically. In some of these operations the electric wires are broken or the firing system is otherwise deranged by pulling casing or the caving of hole prior to the time for firing. Sucn accidents make it necessary for the driller carefully to clean cavings out of the hole to a depth close to the top of the charge, after which in the normal practice, an attempt is made to fire the charge by dropping a ""jack-squib"", fitted with a fuse and detonator, down the well. Mr. R. L, Fowler, production manager for the Pierce Oil Corporation, reports that a delayed shot was thus successfully tired through four feet of caved material lying on top of the nitroglycerin shells.When a shot destined to be fired electrically fails, because of the above mentioned accidental conditions to the electric firing system, much time is required for the driller to run casing into the hole and clean out caved material. It was during the time of such uncompleted operations that the spontaneous explosions first noted took place. Having noted these spontaneous explosions the well shooters now intentionally place a charge in deep holes, which because of probable caves would otherwise have to be tired electrically, and wait for the charge to go off. No detonators are placed with the charge.

May 1, 1920

By Francis R. Redfern

Newton's method of solving a nonlinear equation is employed to develop a least-squares acoustic emission source location method in which the spatial residuals of the location equations are minimized. These residuals, related to the distances from the least-squares source location perpendicular to the surfaces described by the location equations, permit location error to be estimated to first order along the spatial axes. The solutions obtained by this method are the best spatial solutions to the location equations in the least-squares sense. Also presented is a procedure by which the geometrical control of a transducer array can be evaluated using the rate of change of source location with fractional velocity change.

Jan 1, 1982

By H. B. Freeman, E. J. Gleim

During the 12 months ended July 1, 1931, engineers of the Bureau of Mines examined electrical equipment in 80 bituminous-coal mines. The purpose of these examinations was to ascertain the condition of such equipment with respect to possible hazards of gas and dust ignitions, also of shock. Although only 3 of the 80 were being worked with open lights and therefore did not use explosion-proof equipment, there were others where electric cap lamps were used by the men but where it was apparently assumed that conditions as to gas and dust did not require equipment designed to give protection against ignitions. Early in its history the United States Bureau of Mines originated certain standards covering the construction and testing of electrical equipment in order to minimize the dangers of ignitions from exposed electric sparks and flashes ; accordingly, it is comparatively easy to determine wherein a machine built to these standards falls short of continuing to meet them if damaged or neglected. Many so-called flame-proof and dust-proof machines, however, have not been built to any standard comparable with that developed by the Bureau of Mines. In addition, certain machines have parts which pass Bureau of Mines tests, but do not satisfy the full requirements in other respects, and others make no pretense of inclosing the spark-producing parts. It is not uncommon to find two or more of these various types in the same mine with " permissible " machines, the type that has been built to conform to the Bureau of Mines standard. Consequently, inspection of nonpermissible machines becomes somewhat difficult without a standard of comparison. Because of its unprotected condition obviously open-type electrical equipment must be used with great care, if at all, in a mine where precautionary measures are adopted in guarding against gas and dust ignition. The unsafe nature of such equipment is widely recognized. For that reason it is to be installed only where there is no likelihood of gas being present. It is not apparent to some, however, why flame-proof and dust-proof equipment and equipment having tested parts should not be regarded in the same light as permissible equipment.

Jan 1, 1932

By L. W. Higley

Particulates generated in electric furnace (EF) steelmaking constitute approximately 1 to 2 pct of the charge. This flue dust is a rich source of zinc (values are substantially higher than in ore), but although there are several processes for recovering the metal, none are considered economic in the United States. This report reviews extraction technology and presents results of Bureau of Mines reduction-volatilization tests on pelletized EF dusts which achieved high recoveries of zinc. The data are sufficiently encouraging to warrant consideration of EF dusts as raw material for primary zinc smelters.

Jan 1, 1977

By R. C. Buehl

[Improvements in refractories for high-temperature service have made possible the use of higher temperature in many processes. Consequently, it sometimes is desirable to use gases heated above 1,600° F., and for moderate rates of gas flow, there gases can be heaters best with pebble heaters. Pebble heaters of the stationary-bed type in which the chanber was lined with mullite brick and pebbles of pure alumina served as the heat-exchange medium have been used recently to heat the air blown into an experimental blast furnace4/ These pebble heaters worked well and made it possible to use air temperature up to 2,500° F. at the tuyere of the furnace. Since little has been published on this type of gas heater, a review of the construction on employed and operating data should assist in selecting applications and designing units.]

Jan 1, 1953

Measure the leakage through individual crosscut stoppings quickly and economically so that the worst ones can be identified and repaired. (Typically 60 to 80% of the air supplied to a mine short circuits before reaching a working face.) Approach Most of the leakage through a permanent stop-ping is channeled through two windows in a temporary stopping, and air velocities through the windows are measured; leakage is determined from a formula. How It Works A temporary stopping made of plastic brattice is erected in the same cross cut as the permanent stopping, either upstream or downstream. The brattice is fastened to the roof, bottom, and ribs of the entry with spads. Normal leakage of brattice was allowed for in deriving formula, and does not effect results. For best accuracy the brattice and the stopping should be separated by a distance of one hydraulic diameter.

Jan 1, 1979

By J. C. Edwards

The Bureau of Mines developed a mathematical model that decribes the interaction of an automated breathing and metabolic simulator, or lung, with a self-contained· self-rescuer that is supplied compressed oxygen. The model can be used to predict the gas partial volumes of 0z, Nz, and COz in the lung and in the self-rescuer breathing bag for a prescribed metabolic state that characterizes the lung. Nonlinear rate equations are used to describe the temporal evolution of the gas partial volumes. A numerical procedure was established with a FORTRAN computer program to solve these equations, which correspond to a given metabolic state. Examples are presented of applications of the model to predict bag volume and bag oxygen concentration changes with time when the bag is controlled by an automated breathing simulator. Under certain restrictive conditions, the model equations can also be used to analytically pre-dict the time required for the bag to reach a maximum or minimum volume. The model equation in this latter case was extended to transi-tions between metabolic states, with transitions described as exponential growth or decay processes.

Jan 1, 1985

1.1 Bituminous-Coal and Lignite Dust. - Carboniferous material having a volatile ratio of 12 percent or more by weight and a fineness such that the material passes through a No. 20 sieve. 1.2 Active Underground Workings. - Underground places in which men are required to be or to pass through in the performance of normal mining operations for the production of coal. 1.3 Working Areas. - Underground areas where bituminous coal and lignite are mined, specifically: (a) Face. - The solid surface of the unbroken portion of the coalbed at the advancing end of the working place. (b) Face Area. - The working area inby the last open crosscut in an entry or a room, including the pillar being extracted or longwall being mined. (c) Room. - A place abutting an entry or airway where coal has been mined and extending from the entry or airway to a face. (d) Crosscut (Breakthrough). - Passageways or openings cut through a pillar to connect adjacent entries or rooms. 1.4 Entry. - Underground haulageways, travelways, and airways, except working areas as defined in section 1.3. (a) Active Entry. - An entry in which coal is being mined from a portion thereof or from connected sections. (b) Parallel Entry. - Usually an intake airway parallel to the haulageway. (c) Back Entry. - Usually a return airway parallel to the haulageway.

Jan 1, 1960

The object of this program was to extend the capabilities of visual paging systems both in size and function. The system developed uses the mine pager phone line for communication, monitoring, and remote control. A central station, using a mini-computer, transmits signals by phase inversion modulation of a 16,384 Hz carrier to as many as 999 remote units. The remote unit addressed returns an echo to indicate that it is functioning and, in the case of monitor units, to convey the monitor data. Magnetically latched display discs, which can be seen from both sides when posted, are used for visual paging. Lists of the addresses of posted pages, unanswered pages, and non-echoing units are prepared by the central station computer. The system was designed to be intrinsically safe and should operate for three months on a 12-volt lantern battery.

Jan 10, 1980

By Joseph A. Sutton

The prospect of utilizing bacteria in mining and metallurgical processes introduces a new and challenging area of investigation. Elements of bacteriology and metallurgy are discussed in connection with possible areas where biological science might be applied in extractive metallurgy. Bacteria may prove important in the selective separation of metals from ores and metallurgical solutions, the production of sulfur from gypsum or pyrites, and the production of sulfuric acid from elemental sulfur. A series of reports concerning the experimental applications of bacteria on minerals and metallic ores will follow this paper. For several years the Bureau of Mines has been investigating the action of bacteria in the oxidation of sulfide minerals and their potential uses in metallurgical processes. Primary attention has been given to the possible utilization of certain strains of autotrophic bacteria that live in industrial leaching solutions or fractures of mineral outcrops. The purpose of this paper is to acquaint the mining and metallurgical engineer with micro-organisms and some of their possible applications in the field of extractive metallurgy.

Jan 1, 1961

By George M. Lucich

This report describes a sensitive, proportional temperature controller developed by the Bureau of Mines that is useful in the temperature range from 40 to 400° C with an accuracy of ±0.10 C. A temperature controller of this kind is potentially useful for regulating temperatures in air chambers, liquid baths, furnaces, and reaction vessels, and for other applications. This instrument was developed to control the duration and temperature of the heating cycle of a charcoal-filled adsorber that is part of a special helium analyzer used by the Bureau. The controller was made from commercially available parts, and can be easily modified to provide continuous temperature control. The circuit is solid state and employs no electromechanical devices. Over a 2-year period of use as a component of the special helium analyzer, this temperature controller performed successfully and required no maintenance.

Jan 1, 1979