Search Documents

By F. W. Penn

An aircraft auxiliary power unit (APU) was used as an exhaust source for evaluation and refinement of sampling and analytical procedures for gas turbine engines. The unit was also used to determine the emission characteristics of APU's in service and to study the effect of fuel composition and combustor design on exhaust emissions. Carbon monoxide, carbon dioxide, oxides of nitrogen, hydrocarbons, aldehydes, particulate loading, and odor were measured at engine operating modes representing the duty cycle encountered in airline operation. Analyses showed good repeatability, and adequate sensitivity was attained in these experiments. Smoke opacity measurements were not taken owing to the lack of a high-sensitivity smokemeter. Results showed that the minimum emission levels occurred with the standard combustor and Jet A fuel. Emission rates were highly dependent on test mode, but emission patterns as a function of test mode were similar for all fuels and combustors tested. A comparison of three identical design production combustors showed a variation in average emission rates of less than 5 pct.

Jan 1, 1973

By P. D. Bergman

To assess the efficacy and economics of producing power from coal, four open-cycle magnetohydrodynamic (MHD) processing schemes were selected for study. Each involved a different mode of coal combustion and level of gas cleanliness. The options considered were: (1) coal burned in a slagging combustor; (2) suspension gasification with slag removal prior to combustion; (3) parallel cyclone combustors, one operating fuel rich and the other operating with excess air; and (4) suspension gasification by the hot exhaust gases from the MHO duct with ash removed prior to combustion. Option 1 has the highest ash content in the combustion plasma and as a result would have the greatest operational difficulties associated with it. Options 2 and 4 have the cleanest MHD combustion plasma. For coal priced at $4/ton, the power generating cost of option 4,11.78 mills/Kw-hr, is the highest, with Option 1, at 9.04 mills/kW-hr the lowest. These costs may be compared with a conventional power cost of 9.92 mills/kW-hr for the late seventies. Capital costs of three of the four options were competitive with those of conventional thermal power plants employing stack gas S02 cleanup systems. Option 2 has the most favorable combination of operating characteristics and power cost. It was concluded that a clean, high-temperature working fluid can probably be produced from coal without leading to depressed system efficiencies and exorbitant capital costs.

Jan 1, 1973

Provide d comprehensive source of up-to-date information about technology for revegetating coal mined lands. Approach A great deal of activity and research in the field of coal mine revegetation has been reported in technical literature, both before and after the passage of Public Law 95-87, the Surface Mining Control and Ruclamation Act of 1977 (SMCRA). This information is widely scattered throughout books, scientific journals, periodicals, Government reports, and other sources, and there has been a need to develop a method of accessing it quickly and efficiently. At the request of the Office of Surface Mining Reclamation and Enforcement which promulgates and enforces regulations implementing the act, the Bureau of Mines has prepared a document that identifies literature relevant to coal mine revegetation. Most of the literature available on this subject has been published during the past 15 years. To tap this reservoir of information, 14 data bases were accessed from DIALOG SDI (Selective Dissemination of Information) Service using three keyword combinations (surface mining and reclamation, strip mining and reclamation, and revegetation). This procedure generated over 7,000 listings. The U.S. Department of Energy's ENERGY data base was selected from the 14 DIALOG bases, both for its large number of listings and for its broad coverage of literature. This data base contains all the unclassified information that passes through the Technical Information Center of the Department of Energy, including reports, journal articles, conferences, patents, books, monographs, theses, and engineering materials relating to energy development.

Jan 1, 1986

By M. V. Potter

"In nearly all fields of investigation, research laboratories and routine testing laboratories encounter problems in which the primary determinations involved in the study require the measurement of mechanical vibrations or motions. These vibrations,may be of an oscillatory nature covering frequencies from a few cycles per second up to hundreds of Kilocycles per second, or they may be more or less uniform study nations occurring at rather slow rates. In electrical, or mechanical methods. In the optical case the to cause the deflection of a light beam such that the motion of the mechanican system of the beam can be determined, then by direct the by direct observation on a suitable scale or by recording it’s the electrical methods the motions can be made to changes in resistance, capacity or inductance proportion to the mechanical displacement or electromagnetic means can used to generate directly a voltage that will be porpertuial to the instantaneous vicinity of the vibrations. Other devices are used in a special instance, also but in any cause the electrical methods produce a current that is an electrical counterpart of the mechanical motion, and the motion can then be studied by direct measurements of the current or by recording the current on suitable recording meters or oscillography. Mechanical methods are used in some instance but are generally not as convenient nor as flexible as the optical and electrical methods."

Feb 1, 1943

By K. L. Kreamalmyer, A. B. Neeham

The Alice mine is one of several zinc deposits in Ozark and Howell Counties, Missouri. It was selected as the first to be investigated by the Bureau of Mines in an effort to demonstrate reserves of sulfide ore under the shallow carbonate ores from which all production of the district had come up to World War II. The property was worked first about 1890 and was most productive prior to 1900. Its output was the bulk of the district’s total up to 1940, which is believed to have been about 85,000 tons of washed and sorted ore carrying 17 to 36 percent zinc. The firm of Doane & Ives owned and operated the Alice on a scale of a few to 25 tons a day from 1940 to 1946. An open pit about 300 feet long, 250 feet wide, and 30 to 50 feet deep comprises the mine working. Numerous old drifts and shafts in the walls and bottom of the pit are now inaccessible. The ore consists of zinc and iron minerals replacing and filling openings in dolomite. Sulfides are absent or scarce to a depth of 40 to 50 feet; smithsonite was the chief ore mineral in the oxidized zone. The individual ore bodies are irregular in size, shape, and zinc content, and “horses” of waste occur within the pit. The Bureau of Mines recommended churn drilling to test the depth, extent, and richness of the zinc sulfide ore. Four holes were drilled by a private company and seven by the Bureau in and around the pit; several penetrated considerable thicknesses of material containing a few to 10 percent (metallic) zinc in the form of sphalerite.

May 1, 1947

By F. D. Osgood, A. C. Fieldner, W. A. Selvig

In connection with investigations being conducted by the Bureau of Mines regarding pulmonary disease which is prevalent among metal miners in certain districts , a large number of rock- dust samples have been collected , and have been examined in the Bureau's laboratories . The earlier work has been described in Bureau of Mines Technical Paper 105 , " Pulmonary disease among miners in the Joplin district , Missouri , and its relation to rock dust in mines " by A. J. Lanza and Edwin Higgins , 1915 , and in Bureau of Mines Bulletin 132 , " Siliceous dust in relation to pulmonary disease among miners in the Joplin district , Missouri , " by Edwin Higgins , A.J. Lanza , F.B.Laney , and Geo . S. Rice , 1919. The methods of collecting and examining dust samples have been greatly improved during the investigation , much valuable information having been made available by similar investigations conducted by the Miners ! Phthisis Prevention Committee , Union of South Africa . The latter are described in the " General report of the Miners ' Phthisis Prevention Committee , Johannesburg, Union of South Africa , 1916 " , and " Final report of the Miners ' Phthisis Prevention Committee , Johannesburg, Union of South Africa , 1919. " The investigations by the Bureau of Mines and the South African committee show that by prolonged inhalation of air containing minute particles of sharp and insoluble rock dust , the lungs retain sufficient dust particles to cause decided injury to the lung tissue , the injured lung becoming very susceptible to the development of tuberculosis .

May 1, 1920

By G. E. McClelland

As part of its mission to assure an adequate domestic supply of metals essential to the Nation's welfare, the U.S. Department of the Interior, Bureau of Mines, investigated a particle agglomeration technique as a means for improving the flow of leaching solution through heaps of clayey or finely crushed, low-grade, gold-silver ores. Bench-and pilot-scale experiments showed that the percolation rate of cyanide leaching solution was markedly enhanced by mixing the ore with a portland cement binder, moistening the mixture, and mechanically agglomerating and aging the feed prior to heap building and leaching. The rate of gold and silver recovery markedly increased because of the increased, uniform percolation of leaching solution through the agglomerated feed. The use of concentrated cyanide solution instead of water during the agglomeration procedure decreased the leaching time required to obtain maximum recovery. Results of bench-and pilot-scale experiments are discussed.

Jan 1, 1981

By John Henderson

If you missed this year?s Texas State Holmes Safety Association meeting, you missed a great one. On January 23 & 24, 2009, we held the meeting that was rescheduled when Hurricane Ike threatened Corpus Christi in September 2008. Sixty-five persons from across the state attended the meeting held at the Holiday Inn Emerald Beach. The weather was 82 degrees, and the sky was clear and perfect for a safety meeting. Evaluations submitted by the attendees gave the presentations, the networking, and even the food top marks. There were eight councils represented; Big Country, Central Texas, Costal Bend, Heart of Texas, Hill Country, North Texas and North Central. Presentations included Workplace Examinations, Emergency Preparedness, Screen Safety, Contractor Responsibilities, Powered Haulage, Supervising for Safety, and Basic Inspections of Slings and Rigging. Mr. Edward Lopez, SC MSHA District Manager, gave the State of the District Address.

Jan 1, 2009

By Isaac A. Zlochower, Michael J. Sapko, Ronald S. Conti

This paper describes a U.S. Bureau of Mines investigation of large-scale coal dust explosions in an experimental mine using a high speed electro pneumatic mechanism for the rapid grab-sampling of gases and dusts. This technique enables the monitoring of pyrolysis and charring in fuel dust particles, and the collection of gaseous combustion products, in both large and small-scale explosions. Data obtained from full-scale dust explosion tests at the Bureau of Mines Lake Lynn Test facility show the following: Rapid sampling appears to "freeze" the burned gas compositions at the flame temperature values. Gas samples taken entirely in the flame zone consist of pyrolysis and combustion products with very low residual oxygen. The particles collected in the flame zone show signs of extensive pyrolysis and charring. Measurements of gas concentrations and particle flame temperatures suggest that char burning may have occurred in the flame zone.

By Margaret R. Egan

The U.S. Bureau of Mines investigated the product-of-combustion (POC) characteristics of combustible materials used in typical coal mining operations in a series of experiments conducted in an intermediate-scale fire tunnel. The materials examined include wood cribs, transformer fluid, coal, conveyor belting, brattice cloth, and ventilation ducting. Smoke and toxic gases evolved from burning materials contribute to panic conditions and hinder escape. Smoke irritates and obscures vision, while toxic gases physically debilitate and disorient the victims. However, POC emissions may be used for early warning fire detection. POC levels will vary not only between materials but also between stages of combustion and the conditions in which they are burning. This report summarizes the POC characteristics of each material and evaluates their effectiveness for early warning mine fire detection. Results show that smoke was the POC most readily detected from the smoldering materials tested.

By Daniel N. Tallman

To provide technology for achieving more efficient water filtration systems for the mineral industry, the Bureau of Mines performed demon-stration filtration tests at three iron ore mines and one steel mill. A comparison of equivalently sized magnesium oxide (MgO) and sand filters showed that MgO had a higher capacity and could operate at higher fil-tration rates than sand. In demonstration tests when alum (AlK(S04)2) was the coagulant, suspended solids breakthrough occurred even though the pressure across the filter (head loss) was 7 psig or less. Under these circumstances, the MgO demonstrated 20 to 100 pct greater filtra-tion capacity, defined in terms of the volume of water filtered before breakthrough. When an organic floccu1ant was used at one location, head loss was the run-limiting factor; the filters essentially plugged with-out any solids breakthrough.

Jan 1, 1985

By Richard O. Kneisley

Microseismic activity observed in both the laboratory and underground indicates that a quiet period, associated with the closure of existing fractures and strongly influenced by coal seam microstructure, occurs prior to coal bumps. Field studies conclude that coal mine bumps occur against a background of this so-called microseismic calm. This Bureau of Mines report summarizes microseismic activity associated with face bumps and floor bursts in a deep, western U.S. coal mine. Results conclude that while bumps are often accompanied by panel-wide increases in microseismic activity, bumps are not only preceded by a localized decrease in activity, but occur within these quiet zones. The results of this study concluded that microseismic activity may be applicable to the global detection of potential bump-prone zones, but that future studies are necessary to confirm these findings and to improve the techniques for evaluating stress control effectiveness.

Jan 1, 1989

By G. B. Atkinson

Properties of catalysts prepared from intermetallic compound precursors were investigated by the Bureau of Mines as part of its mission to decrease U.S. dependence on foreign sources for scarce catalytic materials, such as nickel, cobalt, and chromium. Methods were developed whereby catalysts with surface areas of 30 to 40 m2/g were prepared from intermetallic compounds. Activity of these catalysts for the methanation reaction and methanol synthesis was deter-mined using a fixed-bed, single-pass, flow-through reactor. Catalysts prepared from rare-earth-nickel intermetallics had specific activity for methanation that was five times greater than that of commercial catalysts and were equal to or better than commercial catalysts with regard to sulfur tolerance. Under identical reaction conditions, catalysts prepared from thorium-copper intermetallics produced more than 10 times as much methanol as a commercial low-pressure catalyst and exhibited a high degree of catalytic stability.

Jan 1, 1982

By C. E. Jordan

The Bureau of Mines conducted laboratory studies on methods to increase the recovery of brine from slime produced by operating potash plants. The slime was comprised of 80 percent brine saturated with KCl and NaCl, and 20 percent solids. A variety of settling techniques, filtration methods, continuous centrifugation, and novel processing techniques were investigated. Vacuum filtration recovered 6S percent of the brine at 47 gallons of brine per square foot per day. Pressure filtration, on the other hand, recovered 74 percent of the brine at 40.9 gallons of brine per square foot per day. Centrifugation in a 6-inch-diameter continuous decanter-type separator resulted in 42 percent recovery of the brine at a treatment rate of 542 gallons of brine per day. Vertical drains proved to be the most promising novel debrining technique investigated. With this method, 45 percent of the brine was recovered in 3 days.

Jan 1, 1977

By Tye J. Lasich

This project involved modeling rock masses with varying Rock Mass Rating (RMR) values to determine the degree of instability that develops around an underground opening as a function of RMR. The modeling was performed using Itasca?s UDEC distinct element software, which allows explicit modeling of blocks of rock and how they interact with each other. The analyses included three different orientations of the joint sets, four different joint spacings and three different values of joint strength, which combine for a total of 36 different combinations of model parameters. Two different modes of behavior were observed: local failure of area immediately surrounding the roof and sides of the opening, and deep-seated failure extending a large distance beyond the opening. Quantification of the size of the unstable area that developed provides numerical validation of empirical guidelines used in design of ground support and instrumented monitoring systems.

Jan 1, 2005

By G. R. Hopkins

"Summary An apparent decline in fuel efficiency at refineries, which first became came evident in 1930 and continued through 1933, was checked in 1933 when the average amount of heat needed to refine a barrel of crude oil amounted to 660,000 B.t.u. This compares with an average requirement of 692,000 B.t.u. In 1932 and with a low of 639,000 B.t.u. in 1929. (See fig. 1.) The improvement in fuel economy in 1933 probably was closely related to the increase of 5 per cent in crude runs to stills. As much of the fuel burned at refineries is utilized for purposes other than under crude-oil stills and in relatively stable amounts, it is evident that a material increase in crude runs will usually reflected in a decrease in average fuel requirements. Another factor which has influences fuel economy at refineries in the past is the trend in cracking, a refining process requiring more than the average expenditure of heat. In 1933 production of gasoline by cracking increased slightly, but no appreciable rise in heat requirements resulted as an equivalent amount of fuel was saved in improved technique, particularly in the field of heat exchange.Since the beginning of the refining industry, the transition in fuels has been from solid to liquid to gaseous; in other words, the leadership was first held by coal, then passed to oil, and is now held by gas. In 1933, 54.7 percent of the total heat units generated came from gas, 39.0 percent from oil (including acid sludge), and 6.3 percent from coal and coke. The principal change in the relative importance of the various refinery fuels in recent years has been the rapid growth in consumption of refinery or still gas at the expense of all the other common fuels. Still gas owes its ascendency to its cheapness and availability, and probably it would have become the primary refinery fuel years ago if recovery methods had been perfected. The relative importance of coal showed a small increase in 1933, the first gain recorded since these surveys were inaugurated in 1925. The increase in use of coal was undoubtedly due to increased operations at plants using it,"

Feb 1, 1935

By A. J. Miscoe, W. M. McKewan

A unique machine for inducing bending fatigue in wire ropes was built at the U.S. Bureau of Mimes' Pittsburgh Research Center. This machine can produce nine levels of degradation through repetitive cycling of long samples of wire ropes of the types used in the mining industry. This report provides an analysis of the results of the first wire rope to be fatigued on this machine. These results have indicated that as a wire rope accumulates bending cycles, its strength first decreases because of wear and then in- creases due to cold working of the wires. As the amount of cold working increases, more and more of the embrittled wires break and the strength of the rope decreases rapidly. In this test, application of several of the regulatory retirement criteria to various sections of the rope suggests that there may be some inconsistency among them.

Jan 1, 1993

By Barbara Fotta, Lynn Rethi

Within the Mine Safety and Health Administration's (MSHA's) classification of metallnonmetal (MAM) mining, the number of independent contractor' employees has increased significantly in recent years. In 1985 independent contractor employee hours reported to MSHA accounted for 4.5% of all M/NM mining employee hours (excluding office workers); by 1994 that proportion had doubled to 9.0%. As a result, these workers now account for an increasingly significant proportion of fatal and nonfatal mining accidents. According to MSHA's statistics, annually computed fatality incidence rates (the number of fatalities per 200,000 employee hours) for independent contractors working in M/NM mining are consistently higher than those for operator employees. Over the five-year period from 1990 through 1994, 53 independent contractor employees were fatally injured while working on M/NM mine property (See Table 1). More than one third of these fatalities (36%) were due to accidents involving powered haulage; 21% were machinery accidents; and 11% percent were falling material accidents. Combined, these three accident classifications accounted for 68% of all independent contractor fatalities occurring on M/NM mine property during these years. Clearly, current efforts to increase the safety of the mining workforce must also address the safety of the independent contractor employee. This report is a preliminary attempt to identify trends in the employment and safety of independent contractor workers by identifying which segments of M/NM mining are experiencing the greatest increases in the number of independent contractor employees and by examining changes in the rates and types of accidents in which these employees are involved. The employment and accident data used in this report were obtained from the MSHA database. [ ]

By George H. Ashley

Character The bituminous coals of Pennsylvania range from low volatile to high volatile, but are all low moisture coals The coals are of three types caking of coking, noncaking or splint, and cannel The percentage of volatile matter in all kinds changes from low at the east to high at the west This change is thought to be due to the pies sure and folding to which the coals along with the other rocks have been subjected In the Broad Top field, and in Somerset, Cambric, Clearfield, Centre, and other counties to the northeast, most coals contain from 3 to 5 times as much fixed carbon as volatile matter, the fixed carbon ranging from 67 to 75 per cent, and the volatile mattes from 16 to 24 per cent These coals are classed as lovol coals In the line of counties just west of those listed the coals are of the medium volatile class (midvols) This includes the famous Connellsville coking coal Still farther west, covering most of Washing ton and Westmoreland counties, and the counties to the north of them are high volatile coals of gas coals (hivols) This is discussed in Part I on the geology of the coals of Pennsylvania, where is given in isocaib map Cannel coals ale found in many par is of the bituminous coal field of Pennsylvania, but in particular in Beaver Butler, Armstrong, Indiana, and Clear field counties The cannels of Beaver and Butler. counties are typical high volatile cannels, many of which have been used in times past for oil distillation The cannels of Armstrong and Indiana counties are medium volatile cannels, and while main taming the physical character of cannels, have no more volatile neat ten than the coals around them The cannels of Clearfield County tie low volatile Splint coals of noncakmg coals are not abundant in Pennsylvania. The Sharon coal, formerly mined in Mercer County, was a noncaking or splint or block coal, and was formerly used in the raw state in non smelting Uses STEAM COAL Practically all of the coals of Pennsylvania are steam coals, though many coals in the Commonwealth, because of high ash, are not good steam coals The coal of the Pittsburgh district has long been famous

Jan 1, 1928

By T. H. Ueng, S. D. Thompson, Y. J. Wang

"INTRODUCTION There is considerable interest among mining companies and government agencies in finding new ways to better control the generation and dispersion of respirable coal dust. Mine face ventilation generally has been considered the most effective tool for lowering the concentrations of respirable dust. Unfortunately, only a limited amount of research has been undertaken to determine the relationships between the various face ventilation parameters and the dust dispersion patterns. If these relationships are better understood, more efficient ways of controlling dust generation and dispersion may be evident. A practical and economical way to gain more in-depth understanding of these relationships is through scale model studies. Past research (1, 2, 3) has substantiated that scale models can be successfully used in studying ventilation parameters provided that geometric, kinematic, and dynamic similitues are maintained.To better understand face ventilation and dust dispersion, a 1/5 scale model of a room and pillar mine face was constructed. This model was then used to conduct experimental investigation on two ventilation parameters. The parameters which were examined included the line brattice distance from the face and the air quantity. The values of these parameters were varied in numerous experiments so that their effects on dust dispersion could be measured.The experiments of this study were unique in two ways. First, two different substances were used to simulate the respirable coal dust. Experiments were conducted with a tracer gas (methane) serving as the dust simulation substance. They were then repeated with an actual dust (Arizona Road Dust) replacing methane as the dust simulating substance. In previous scale model studies, the dust simulation substance has been limited to a tracer gas such as methane. The validity of using a tracer gas to simulate dust is not clearly known yet. The other unique thing about these experiments was the number of points measured for methane (or dust) concentration. Twenty five points in a grid arrangement were measured during each experiment of this study. The number of points measured for concentration in other studies has generally been very small (often 2 to 4). It is difficult to obtain an accurate assessment of how the ventilation parameters are effecting dust dispersion when only 2 to 4 points are measured."

Mar 1, 1989