Search Documents

By Robert E. Johnson

THE MILDEST recession of the postwar period ended in the first months of 1961, and the economy climbed steadily during the remainder of the year. The Federal Reserve Board (FRB) Index of Industrial Production climbed from a low point of 102 (1957=100) in February to 115 in December, a rise of 12.5 percent. But economic activity for the year as a whole was only 1.5 percent higher than the 1960 level, as measured by real gross national product (GNP). Although activity increased throughout 1961, much of it was merely regaining ground lost in the decline during the second half of 1960 and the first months of 1961. The FRB index did not re ain the July 1960 high of 110 until June of 1961. Mineral fuels did not fully share in the economic recovery. The (FRB) crude oil and natural gas index rose only 5 percent between February and December. Although the index of monthly coal production increased 11.5 percent during the year, the February level was so low that total production for the year was the lowest since 1954. Total production of energy measured in Btu's was up slightly (1 percent) during the ear. Coal production was down; production of crude oil and natural gas was up. Calculated consumption paralleled production-total up slightly, coal lower, and crude oil and natural gas higher. The most interesting product developments were in coke and residual fuel oil. Sales of coke showed a sharper drop than steel

Jan 1, 1962

By Joseph E. Chilton, Robert J. Timko, Charles D. Taylor

No regular monitoring of methane is required in areas of gassy coal mines outby the mining face. Methane ignitions that have occurred in mine outby areas indicate the need to provide better protection to workers. Handheld methane monitors are now used by some miners to make periodic measurements of methane at the working face. The IYONI II gas detector which is incorporated into a miner’s cap lamp and worn on a miner’s helmet can continuously provide an alarm signal whenever methane levels exceed a set level. Tests were conducted to evaluate the performance characteristics of this methane detector by measuring response times with methane gas supplied through a calibration fixture or adaptor. Other response time tests were performed with the detector in an environmental test box. Performance was also evaluated in a full scale test gallery where face methane emission and underground ventilation were simulated. Procedures for calibration by response time measurement of the IYONI II detector have been developed. In limited testing, the IYONI II detector was found to reliably detect the presence of 1 percent by volume methane.

By Ivette E. Torres

The series summarizing the prices of the major nonferrous metals on the stock exchanges of the United States and the United Kingdom (London Metal Exchange) has been continued this year in tables 22 and 23. Time constraints have prohibited preparation of other price information that has appeared in this study in previous years. Users are urged to consult the 1993 U. S. Bureau of Mines publication Metal Prices in the United States through 1992, which gives an analysis of historical price series and trends, or the 1993 edition of Mineral Commodity Summaries for current U.S. prices on non fuel commodities, and to utilize U.S. Department of Energy sources for information on fuel material costs.

Jan 1, 1994

By B. J. Scheiner

The Bureau of Mines investigated an electrolytic technique for oxidizing ore slurried with brine to determine its effectiveness in extracting mercury from ores. Optimization experiments conducted on a 2.5-pound-mercury-per-ton ore resulted in 95 percent mercury extraction with operating conditions of 30° C, a current density of 0.5 ampere per square inch, and a treatment time of 3.5 hours. Corresponding power consumption amounted to 38 kilowatt-hours per ton of ore treated. Amenability experiments conducted on 62 different mercury ores resulted in 90 to 99 percent mercury dissolution from ores containing 0.6 to 20 pounds of mercury per ton of ore, Treatment time ranged from 1 to 7 hours in 4-to 20-percent sodium chloride solutions, and power consumption was in the range of 10 to 50 kilowatt-hours per ton of ore. Pilot mill experiments in a 100-to 200-pound-per-hour extraction plant have been in progress to quantify power and reagent requirements. These data will be reported in a subsequent publication.

Jan 1, 1973

By R. V. Ramani, C. B. Manula, A. Owili-Eger

ANALYTICAL PRESSURE - VOLUME COMPUTATIONS FOR THE MINE PROTOTYPE A new coal mine is projected, with entrance by slope 1,500 feet long. Nine main entries will be standard for development, five as intake and four as return. One return shaft is planned near the slope bottom, and an intake shaft and portal are planned 5,000 feet north of the slope bottom. The slope will have an area of 150 square feet and a perimeter of 55 feet. A belt and supply track will be within the slope. The return shaft will be circular with a diameter of 18 feet and will be 500 feet deep with an escapeway. Two hundred feet of the shaft and 500 feet of the slope will be concrete lined. Select the fan to operate five units per shift and drive the 5,000 feet to a proposed new portal, using the slope for an intake. Two main splits are planned with the maximum of three units on any split. The amount of air desired at each unit is 25,000 c.f.m; a shop at the slope bottom will require 10,000 c.f.m. In the solution of this or any similar problem, the first step is to determine the resistance factors. CALCULATION OF R FACTORS Slope area = 150 sq. ft.; Perimeter = 55 feet; Length = 1,500 feet. The friction factor K must be established. Five hundred feet of the slope is smooth lined, moderately obstructed by belt; K = 35. The remaining 1000 feet is in sedimentary rock and moderately obstructed; K = 85.

Jan 1, 1975

By James M. Spear

The U.S. Bureau of Mines and the U.S. Geological Survey conducted a mineral survey of the Black Butte RARE (I area during the summer of 1981. The study area encompasses 17,800 acres [27.8 sq mi (7,233 ha)] along the course of the Black Butte River, 13 mi (22 km) southeast of Covello, California. No mineral deposits were identified by the U.S. Bureau of Mines during this survey. Assay results of samples taken in this area indicate only trace amounts of manganese, chromium, and nickel. No radioactive or fluorescent minerals were detected. No oil and gas, coal, or geothermal leases have been recorded for the study area.

Jan 1, 1982

By R. A. Beall

Homogeneous zirconium-alloy ingots have been cast on a production basis by the consumable-electrode arc-melting process at the Northwest Electrodevelopment Experiment Station, Bureau of Mines, Albany, Oreg. This paper describes the various methods used to introduce alloying materials into the ingot and evaluates 1 each method by the degree of homogeneity of resulting ingots, as determined in tests on sections cut from the ingots. As many as 30 or more ingots, each 6 to 10 inches in diameter and weighing 300 to 500 pounds, were melted, using each method; and, as most of them subsequently were fabricated to strip 0.1 inch thick, the test results are considered to be representative of production practice. Ingot homogeneity has been considered more difficult to achieve in arc-melting practice than by methods where the molten metal is poured into molds and the addition can be stirred into the total mass of metal before casting. Owing to the unique requirements of consumable-electrode arc melting the addition can be made only to that part of the total mass of the ingot that is molten at one time. Observation of the flowlines in 500-pound ingots produced at Albany indicates that the molten pool has a maximum depth about equal to the ingot diameter. The weight of metal molten at one time is, therefore, not over 100 pounds. Characteristically, the arc-melting process is conducive to segregation, which can be overcome, at least partly, by adding the alloy constituents almost continuously during casting.

Jan 1, 1956

By Clyde E. Eilliams

In recent ye.ars much intere,t has been centered on the possibility of pro­ducing alumina from clq, a.nd proposed methods tor the recove:r,v of alumina are appearing constantly in parent lit,erature, As a good· grade of clay contains from 30 t<> 40 per cent of al"WDina, the prospect of tecovering it is alluring, al though obviously ditfieul t. A patent typical of m projected thermal processes is that 0£ Paul Migu.et, (U, S, Patent No, l,376,563) entitled nprocess for the preparation of pure alkaline alu:ninates.'' Re proposes to prepare alkaline a.luminate by fusing clay, lime, and acrap iron with a reducing aget in the electric furnAce, thereby reducing the silica a.r.d formin1s calcium alumina.te and ferrostlicon, The calcium aluminate, being lighter, would. float on top substantially free from foreign oxides, It could. then be tapped ott, cooledf ana later crushed and leached with aodium carbonate solution to torm, by double decomposition, sodium aluminate, and calcium carbonte. The fonMr is soluble and yields readily aluminum hydroxicie. 'l'he ferrosilicon wo'Uld be r,covered as such and sold at a profit.

Aug 1, 1922

By R. C. Hickman

"INTRODUCTION The most productive area of the eastern Virginia pyrite belt lies to the north of the village of Mineral., in Louisa County. The largest producers of pyrite ore in the area were the Armenius, Boyd Smith, and the Sulphur mines.The Boyd Smith mine started production about 1890 and operated more or less continuously until 1922, when competition from the Gulf States and Spain closed the pyrite mines in Virginia. There are no reliable records of production or value of minerals produced.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the most effective utilization of our mineral resources to the end that they take the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, Oliver C. Palston, chief, analyzes samples and performs beneficiation tests.The project was under the immediate supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch, Bureau of Mines.LOCATIONThe Boyd Smith property is reached from Mineral, Va., by traveling north on State Route 522 about 2-1/2 miles. An unsurfaced road, winding in a northwesterly direction, loads to the Boyd Smith headframe, which is about half a mile from State Route 522 (fig. 1). The tract comprises 181 acres."

Aug 1, 1947

By A. A. Berk

In the course of a study of the formation of external deposits on tubes in water-tube boilers it became desirable to determine the sulfur dioxide (SO2) and sulfur trioxide (SO3) in the Due gases. Determinations made by the A.S.M.E. method for SO2 and SO3 in gaseous products of combustion did not give accurate results. It was found that minute quantities of copper, present in the flue gases from the coal in use, caused oxidation of sulfite in the absorption bottle and that the carbon dioxide (CO2) in the flue gases caused high values for SO2. The A.S.M.E. test procedure was revised to prevent oxidation of sulfite in the absorption bottle and to allow for the effect of CO2; subsequent analyses of flue gases produced reliable results. The revised procedure is described.

Jan 1, 1950

By R. Barany

The heats of formation at 298.15° K of calcium tungstate, calcium molybdate, and magnesium molybdate were determined by solution calorimetry. For the heats of formation from the elements, the values obtained were calcium tungstate, -402.4 ± 0.5 kcal/mole, calcium molybdate, -369.5 ± 0.3 kcal/mole, -334.8 ± 0.2 kcal/mole. For the heats of formation from the oxides J the values obtained were calcium tungstate, -49.2 ± 0.4 kcal/mole, calcium molybdate, -39.6 ± 0.1 kcal/mole, and magnesium molybdate, -12.9 [ ] 0.1 kcal/mole.

Jan 1, 1962

By T. O. Llewellyn

Laboratory batch and semicontinuous studies showed the feasibility of using methylene bromide and trichloroethylene in heavy liquid cyclone concentration of a Nevada brucite ore. Cyclone tests of minus 20- plus 200-mesh material at specific gravities of 2.42 and 2.44 recovered 71.6 to 74.9 percent of the MgO at grades of 95.5 and 95.4, respectively. Neither increasing the feed pulp density from 5 to 25 percent solids, nor varying feed pressures from 25 to 60 psig had any apparent effect on the heavy liquid separation.

Jan 1, 1971

By W. L. Staker

Alternatives were developed to the conventional ammoniacal carbonate leaching-steam stripping procedure for recovering copper as an oxide from contaminated scrap metal. By entraining air bubbles in the leach solution, the copper dissolution rate was increased to 1.5 g/in2 of copper surface per hour, compared to 0.5 g/in2/hr produced by conventional agitation in stirred tanks. Using entrained nitrogen gas bubbles for agitation in conjunction with powdered sulfur not only resulted in rapid dissolution but also simultaneous precipitation of the copper from solution as a high-grade cuprous sulfide.

Jan 1, 1971

Minimize the risk of conveyor belt fires in underground coal mines by improving the accuracy of and means by which flammability data are acquired. Approach Develop a large, laboratory-scale flammability test for mine conveyor belting that realistically assesses its fire resistance. Background A conveyor belt fire in an underground coal mine is a serious threat to life and property. To minimize the risk of belt fires, the U.S. Code of Federal Regulations (CFR) for underground coal mines requires approved fire-resistant belting. Despite this precaution, about 25% of the reportable underground coal mine fires from 1983 through 1988 involved conveyor belting. In several instances, hundreds of feet of belting were destroyed. The current flammability test for fire-resistant belting is specified in 30 CFR, Part 18.65 and is conducted by (be Mine Safety and Health Administration (MSHA). The small-scale test is performed in a 21-in-cubical chamber with 6-in-long by 1/2-in-wide belt samples. To evaluate the flammability of conveyor belting under more realistic conditions, the U.S. Bureau of Mines conducted large-scale fire tests of belting. The large-scale data were then utilized in the development of an improved laboratory-scale flame test for fire-resistant belting.

Jan 1, 1991

By R. V. Ramani, C. B. Manula, A. Owili-Eger

Network analysis of mine ventilation systems is not new, having been traced back to 1854. A Committee Report (1970) has also reported the extensive work done in this respect in the United Kingdom, Japan, U.S.S.R., South Africa, United States, and other countries. Wang, et al (1970) developed a computer program which is an improvement over the earlier one developed by Wang et al (1967). The program has been recently modified and extended to include methane emission features by Owili-Eger (1973). This computer program incorporates all the novel features of the earlier programs. These include the capabilities of mesh selection, free splitting, internal or external fans, natural ventilation pressure and fixed quantity branches. The program is written in Fortran IV and, in effect, is an experimental mine in which many ideas can be tried out. The computer produces, besides the input data and certain computational data, the quantities and head losses in the branches, the head losses to be adjusted in the fixed quantity branches and the fan operating point. The last named program, hereafter to be referred to as the PSU/MVS, is presented in Appendix I. The application of this program is demonstrated in this manual through a series of selected examples. Application of the methane generator program is not included here as a detailed report on the subject is available elsewhere (Ramani et al, 1975).

Jan 1, 1975

Remotely monitor overburden response to longwall mining using time domain reflectometry (TDR) and a combination of hardware and software, as part of the U.S. Bureau of Mines (USBM) program to characterize subsidence. Background TDR was developed in the 1960&apos;s as a method to locate, discontinuities in coaxial transmission cables. In this method, voltage pulses sent along a cable are reflected by cable defects. The pulse reflections are used to determine the type and magnitude of the defects. The TDR concept was extended to material property measurement by embedding cables into particular materials and evaluating the cable&apos;s dielectric behavior as material properties were modified. This technique was adapted by the USBM in 1978 for use in monitoring rock movement during underground mining. The same concept is utilized today. A coaxial cable is grouted into a rock mass that is expected to deform. Progressive rock movement causes the cable to deform, as shown in figure 1, and changes to occur in the cable&apos;s electrical properties, which then produce changes in TDR reflection signatures. The technology has advanced to the point where it is now possible to distinguish shear deformation from tensile deformation and to quantify rock mass displacements by analyzing the TDR signatures.

Jan 1, 1995

By Deno Pappas, Gregory Molinda, Eric Bauer, Christopher Mark, Daniel Babich

Groundfalls are much more likely to occur in coal mine intersections than in entries. NIOSH is using the experience of U.S. coal mines to determine the factors which influence intersection instability and provide guidelines for the safe excavation and support of intersections. Detailed field investigations have resulted in a database of U.S. coal mines containing 12 mines and 639 roof falls so far. By using the roof fall rate as the outcome variable, correlations between roof geology (CMRR), intersection span, and roof support have been established. Case studies have indicated that replacing 3- way intersections with 4-way intersections may not reduce the total number of roof falls. Additionally, the size of intersection spans tend to decrease with lower (weaker) CMRR. Protocols have been established for the collections of roof bolt parameters. The performance of individual roof bolts can now be tracked with roof fall rate.

By Charles L. Kimbell

The final tables of this chapter, tables 25-50, extend and expand the statistical series on production that was started in the 1963 edition of the Area Reports: International Volume of the Minerals Yearbook and that was subsequently updated and expanded in the 1965 and 1967-90 editions. Continuing the practice started in 1989, a column has been included in each of these tables providing a 5-year average for 1987-91, inclusive. This should provide a clearer picture more rapidly of the role of each major producer over the 5-year period. The listing order of major producers, however, continued to be, as in past years, in descending order of rank in the year of review, 1991. This group of tables now includes each of the crude minerals that ranked from? 1st to 19th in 1983 terms of value of their output (as well as four others of lesser rank). These 23 crude mineral commodities accounted for 93 % of the estimated value of world crude mineral production in 1983. In addition, world output of five key downstream products-aluminum, steel, cement, nitrogen in ammonia, and refined oil-is included because of their significance as products.

Jan 1, 1993

By Robert L. Marovelli

The thermal conductivities of six rocks were measured by the transient line source method over the temperature range of -850 to 1,500° F. Close-fitting ceramic probes were used in 0.065-inch-diameter holes drilled through 5-to 6-inch-thick rock specimens. Taconite, granite, quartzite, and basalt were used in the tests. The method yields absolute data and is applicable to both laboratory and in situ measurements.

Jan 1, 1965

By Terry S. Cory

This report covers magnetic field strength measurements vs range and frequency in low-medium coal mines. Both quasi-conductor-free and conductor-proximity areas were investigated. The program covered 5 mines, 4 seams, 6 measurement sets, and 3 geographic areas. The results have been summarized in terms of maximum communication range expected per seam and noise condition. Scatter gain is further explored as a simple measure of energy coupled to conductors.

Jan 6, 1978