Search Documents

By Lloyd A. Morley, Robert Stefanko

In the context of the following report, an hazardous location can be described as any industrial area in/which flammable or explosive gases, vapors, and dusts can be encountered. When electrical apparatus is used in such hazardous atmospheres, the chance of a dust or gas ignition is ever present. Consequently, in an effort to reduce the ignition hazard, several protection systems have been devised. Such systems are termed electrical hazard reduction techniques. The most widely accepted and used of these, the explosion-proof enclosure, is the principal subject of this report. However, other techniques are briefly mentioned. Hazard reduction techniques used in coal mine atmospheres (which can contain methane, coal dust, and air mixtures) are classified as Group I. The explosion-proof enclosure commonly used in mines is defined by the USBM Schedule 2G as a device that can contain internal explosions of methane-air mixtures without undergoing damage or excessive distortion and without an ignition of a surrounding methane-air mixture or discharge of flame. (100) Internationally, the definition remains the same except the words "discharge of flame" are not present. (4,5,31,42,52,76,102) The latter description often refers to flame-roof enclosure construction, but the terms "flameproof: and "explosion-proof" commonly have the same connotation. These enclosures which may not be vapor tight, are distinguished by heavy-wall cast or welded construction and bolted or threaded close fitting flanges. Explosion-proof enclosure techniques have been utilized in U.S.

Jan 1, 1974

By D. G. Lee

Diesel particulate matter (DPM) often contains small amounts of metal as a minor component but this metal may contribute to adverse health effects. Knowledge of the mechanism for particle formation as well as the size preference of the trace metals is critical to understanding the potential for health concerns. To achieve this, the size and the composition of each particle should be optimally measured at the same time. Single particle mass spectrometer (SPMS) would be the best tool for this objective. In this paper, we therefore will introduce new findings about the mechanism and distribution of the trace metals in DPM, derived from a study where an SPMS was used to analyze freshly emitted DPM. KEY WORDS : Single particle mass spectroscopy, Diesel particulate matter, Characterization, Metal contents

Jan 1, 2006

By A. R. T. Dennues

"INTRODUCTION There are presented in this report the results of limited studies by the Bureau of Mines of the firedamp safety of some powder-powered tools proposed for use underground in coal mines. This study was made to obtain general information and specific technical data for a cable splicer and some rail punches now commercially available, the aim being to keep abreast of developments and to anticipate hazards.ACKNOWLEDGMENTSAcknowledgments are made to the Mine Safety Appliances Co., Pittsburgh, Pa., for supplying equipment for these tests, and to the Pittsburgh Coal Co. for making possible observations of the use of these tools in coal mines.The assistance of other members of the Explosives Division is acknowledged: J. E. Crawshaw, for examination of ammunition and, propellant powders; H. L. Wilson, for analyses of the natural gas used in the gallery and Jerome C. P. Weinheimer and Martin Bashel, for conducting the gallery tests.GENERALDescriptions of the DevicesPowder-powered tools of the type tested utilize the energy of charge of,propellant powder accomplish tasks. They are essentially small guns adapted to special work. Of the family of such tools now commercially available from one manufacturer, two have been proposed for use underground in coal mines, namely a cable splicer known as model TI and two models of rail punch known as R40 and R60. These tools employ blank-cartridge ammunition and special projectiles to accomplish the work indicated by these descriptive names."

Jul 1, 1947

By Arnold B. Hubbard

This report describes a method of concentrating the insoluble organic material (kerogen) in a rich Colorado oil shale without any apparent alteration of its original chemical form. The method involved treating finely pulverized shale with dilute acetic acid at room temperature to remove the carbonates, which act as a cementing agent for the shale, and cause the shale particles to partly disintegrate into the organic and inorganic components. The acid-treated shale then was centrifuged in different liquid mediums ranging from 1.4 to 1.15 gravity to effect a mechanical separation. From a Colorado oil shale containing 48.0 percent ash, kerogen concentrates containing 43.3 to 8.7 percent ash were obtained. The carbon:hydrogen ratios of the kerogen in the original shale and the different concentrates were essentially the same. The oil:kerogen ratios calculated from Fischer assays of the above samples were essentially the same, regardless of the organic or inorganic contents. This was also true of the assay water:kerogen ratios of the same samples. These data indicate that no significant change occurred in the kerogen during the concentration process.

Jan 1, 1952

By R. W. Freedman

The gas chromatographic method, devised by the Bureau of Mines for analyzing routine mine air samples, was compared with the infrared method used for confirmatory determination of methane in mine air. While maintaining the specificity of the infrared method for methane determination, the gas chromatographic method is more precise, much more rapidly performed, and more convenient.

Jan 1, 1968

By David F. Smith

[The U. S. Bureau of Mines at its Pittsburgh Experiment Station is frequently called upon to determine by laboratory tests the explosibility of suspensions in air of various dusts encountered in mines and elsewhere. Not all dusts which are combustible or contain combustible material will form explosive mixtures with air under ordinary conditions of temperature and pressure. They may not be highly combustible enough. They may contain a considerable amount of inert or non-combustible material or, the dust particles may not, be fine enough to form explosive mixtures. A knowledge off the chemical composition of a dust together with a determination of the size of the particles often gives valuable indications. But in many cases actual explosibility tests are necessary. Such a case is evidently that of powdered soap, whose explosibility hazard the Bureau was recently called upon to determine, Although an explosion which occurred in a soap plant as early as 1890 was attributed4 to powdered soap, it is apparent, due to the great number of inquiries received by the Bureau, that the hazard presented by powdered soap has not been at all generally appreciated. To the writers' knowledge, no extensive investigation of the explosibility of powdered soaps has been made. It is only recently that pure powdered soap has been manufactured on a large scale. The familiar "soap powder" in the past was usually a mixture of soap with a relatively large quantity of sodium carbonate. Often it contained large amounts of moisture and abrasive material. Even a highly combustible dust when mixed with large quantities of inert dust will not form explosive mixtures with air. Pure powdered soap, however, presents a different aspect. Pure soap is formed by combination of alkali (incombustible material) with fatty acid (combustible material). Toilet soap fray also contain a certain amount of glycerin and essential oil winch, being combustible influence the explosibility]

Jan 1, 1928

By Alex C. Smith, Thomas P. Mucho, John B. Walsh, Alden Ozment, Michael R. Thibou, Michael A. Trevits

The National Institute for Occupational Safety and Health (NIOSH), with US Foam Technologies, Inc. and On Site Gas Systems, Inc., conducted research on the remote application of extinguishing agents with the intent of improving deployment strategies to limit miner exposure and to help ensure the best possible outcome during a mine fire. Full-scale in-mine were conducted at the NIOSH Lake Lynn Experimental Mine to determine the flow characteristics, stability and fire-suppression capability of gas-enhanced foam. The in-mine experimental work was designed to evaluate movement of gas-enhanced foam through mine workings closely simulating an underground coal mine environment and how long gas-enhanced foam would remain stable. This paper presents results of the experiments and provides valuable insight into mine fire deployment strategies for gas-enhanced foam technology.

By W. P. Yant, C. E. Traubert

"INTRODUCTION Canister-type gas masks have become an essential part of the equipment of many industries, not only for use in emergencies, but also in performing normal operations of industrial processes and procedures, particularly where ventilation is not practically or economically feasible. They are also used widely for enhancing safety of operations which previous to the development of gas masks had been performed in harmful atmospheres.Since the inception of industrial gas masks the Bureau of Mines has been actively engaged in endeavoring to increase the efficiency and safety of these devices, and this bureau has become a source of advice to manufacturers in producing devices of good quality and to industry in the proper selection and use of these devices. In order to give first-hand information and keep current with the demands and needs of industry it is necessary to perform investi-gations from time to time. This report deals with tests of certain types of commercial gas-mask canisters for protection against mercury vapor.TYPES OF CANISTERS EXAMINEDThis investigation included tests of the following types of canisters:(a) Gas-mask canister filled with 725 c.c. of granular activated charcoal, 8 to 14 mesh, and of a quality used in gas masks which meet the Bureau of Mines approval requirements 4 for protection against organic vapors."

Oct 1, 1932

By Robert P. Vinson

The Bureau of Mines investigated the presence and extent of methane accumulations in mine roof cavities using a full-scale mine model. Methane was released at a constant rate into the roof of a cavity built onto a 700-ft wind tunnel. Two box-shaped roof cavities were used in the study: one had a volume of 114.7 cu ft; and the other had a volume of 57.3 cu ft. Methane concentration was measured at 28 sampling points in the cavities using 21 different combinations of gas emission rates and air velocities. Brattice hung in the cavity helped reduce methane concentrations without auxiliary ventilation. It was also found that the effective ventilation rate increased by a factor of 40 in the large cavity and by a factor of 20 in the small cavity when air velocity was increased from 100 to 600 fpm.

Jan 1, 1978

By Martin H. Stanezyk

The Bureau of Mines investigated leaching of selected copper sulfide minerals and a composite of impure flotation concentrates at elevated temperatures and pressures with ammoniacal solutions. Copper 1 (tractions of 96 percent were obtained by leaching chalcopyrite at 75° C under oxidizing conditions for 60 minutes. An extraction of 99 percent of the copper contained in the composite concentrate was obtained by leaching the product for 90 minutes at 75° C. In tests of bornite, chalcocite, and covellite, 90 to 97 percent of the copper was extracted at 20° C provided an 8-hour reaction period was used. At 75° C essentially complete dissolution of the copper from these three minerals was accomplished in 60 minutes. Additions of ammonium sulfate to the leach solutions were required to obtain high-percentage extractions of the copper from bornite, chalcocite, and covellite. Although ammonium sulfate was not required when digesting chalcopyrite, copper extraction was enhanced and less free ammonia was required when ammonium sulfate was added to the leach pulps. The chemistry of leaching copper minerals was studied. It was C, termined that chalcocite altered to covellite as one step in the dissolution When leaching iron-bearing copper sulfides, hydrated iron oxide formed on the mineral surfaces, indicating that a diffusion process prevailed. No evidence of covellite was detected.

Jan 1, 1966

By J. E. Gebhardt

External control of the electrochemical potential of a bed of mineral particles has been investigated by the Bureau of Mines as a method for controlling particle inter-action with organic collectors and thus, flotation response. A cylindrically shaped, 200-to 300-g bed of sulfide mineral particles was used as the working electrode to examine the potential distribution in the bed. The dissolved oxygen concentration of the electrolyte had a significant effect on the potential profile across the mineral bed. Low oxygen levels were necessary to achieve uniform electrochemical potential distributions. Flotation separation of a chalcocite-pyrite mineral mixture by controlled potential was achieved using ethylxanthate, but the flotation behavior of chalcocite and pyrite from the mixture does not follow the flotation behavior of the individual minerals. That is, the presence of another sulfide mineral alters the flotation behavior with ethylxan-thate. Galvanic interaction due to mineral-to-mineral contact between chalcocite and pyrite contributes to differences in the recovery. Chalcocite dissolution products had a deleterious effect on pyrite flotation by activating flotation below -0.1 V (saturated calomel electrode) and depressing flotation above -0.1 V. Pyrite dissolution products had no effect on chalcocite flotation.

Jan 1, 1985

By Adam K. Smith

Over-exposure to noise remains a widespread, serious health hazard in the U.S. mining industry despite 25 years of regulation. Most other categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. In order to reduce cases of Noise Induced Hearing Loss (NIHL) in the mining industry, retrofit acoustic treatments and controls are being developed to subdue noise at the source. The Mine Safety and Health Administration (MSHA) coal noise sample data collected from 2000 to 2005 has determined that continuous mining machines rank first among all mining equipment whose operators exceed 100% noise dosage. The continuous mining machine conveyor, used to move coal from the cutting face to the rear of the machine, has been identified as a dominant noise source. A dual sprocket conveyor chain was tested as a potential solution. Sound power level measurements conducted at the Pittsburgh Research Laboratory (PRL) accredited reverberation chamber showed a 3 dB reduction in the A-weighted sound power level when the dual sprocket chain was implemented. Underground results show an 8-hour Time Weighted Average (TWA8 hrs) reduction a 3 dB for continuous mining machine operators. Utilizing this newly developed noise control, along with previously proven controls, provides continuous mining machine operators an opportunity to be within the MSHA-Permissible Exposure Limit (MSHA-PEL).

Jan 1, 2009

By John J. Sammarco

This U.S. Bureau of Mines report describes the research effort and results for a computer-assisted appendage control system of a Joy 14CM continuous mining machine. The cutter head (shear), gathering head, conveyor, and stabilizer jack are the appendages. Positional control of each appendage is accomplished by specifying the desired position to the appendage control computer, which uses appendage position sensor data. Appendage movement is actuated until the desired position is attained as determined by control algorithms. A description of the sensors, mechanical and electrical interfaces, data acquisition and control (DAC) system, experimental method to determine appendage response characteristics (range of motion, start and stop delay times, and movement rates), and their application to the position control loop algorithms are presented. Also, the test results for the shear in an unloaded (free space) and loaded (cutting) condition of the shear are presented.

Jan 1, 1991

By S. M. Molloy

The postwar demand for insulating material such as mineral wool, in-creased in proportion to the rapid construction of new buildings, placing an enormous burden on the existing mineral-wool industry both in known sources of raw materials and in available plant facilities. In view of the increased demand on the industry, the Bureau of Mines in its Mississippi Valley Experiment Station" Rolla, Mo., undertook an investigation to aid the industry by establishing resources of raw materials through actual laboratory wool-blowing tests and by developing certain methods for evaluating the physical proper-ties of a mineral wool. As material was received from the public, laboratory-evaluation technique had to be developed, the results of which would reflect in the mineral-wool-industry standards. The methods of testing used by the mineral-wool industry, not only would have required a pilot-plant installation capable of producing a large tonnage of mineral wool, but each wool-blowing campaign would have been very expensive and necessitated considerable personnel and equipment. The present laboratory wool-blowing equipment can produce as high as eight wool-blowing campaigns a day. The nature, simplicity, and size of the physical testing equipment permit testing as small a sample of wool as 25 grams and give information as reasonably accurate as in a 40-pound bag of wool. The purpose of this report is to describe the laboratory method of production and the evaluation of the physical properties of small quantities of mineral wool. Considerable work has already been done, and the interest of the public and industry is measured in the number of samples being submitted for testing.

Jan 1, 1948

By H. L. Gibbs

Many factors contributed to the decision to build a radiochemical laboratory at the Salt Lake City Metallurgy Research Center to investigate the application of radioactive isotopes and chemical compounds in extractive metallurgy. These reasons included the notable success achieved in biological sciences with radioisotopes, the development of reliable instruments and methods for identifying the isotopes and measuring their activities, and the commercial availability of radioisotopes in a variety of forms and known activities. The paramount reason, however, was the realization that better methods were needed for guiding and quantifying research to resolve the complex extractive metallurgy problems under study at the Research Center. This is the first of a series of reports describing the application of radioisotopes and radioactivity techniques in extractive metallurgy. The report includes a discussion of licensing and safety requirements, a general description of the laboratory and the methods used, a definition of the nature and scope of the research program, and a synopsis of the more important problems studied. Subsequent reports will concern radioactive techniques for solving specific problems in mineral dressing, hydrometallurgy, and pyrometallurgy.

Jan 1, 1960

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

3. Application of Proposed Revised Standards 57.11-50 to Mines Surveyed 3.1 Subparagraph (a) 1 "Each mine shall have at least two separate and properly maintained escapeways from each working place to the surface which are so positioned that physical or environmental damage to one will not lessen the effective¬ness of the other, and which meet the requirements of travelways and man hoisting standards These escape¬ways shall reach to within 1000 feet horizontally or 300 feet vertically of each working place " 3. 1. 1 Discussion This section will deal with the 1000 and 300 feet distance requirements, Section 3. 5 will deal with the "environmental damage" provisions. During the course of the mine surveys, it became obvious that one mine's 1000 foot distance was nowhere near equal to another' s --not in the actual distance but in the time required to traverse that distance. This -Ls true for the 300-foot requirement as well. The most obvious example is that one could traverse down a 300-foot raise much faster than climbing up the same distance. The temptation is strong to recommend that the distance requirement be changed to travel times instead. However, this approach would unfortunately lead to a lot of subjective evaluations. Having a time requirement for an entire mine evacuation (Subparagraph 6) is one thing, time requirements and the requisite inspection proce¬dures for each working place are quite another.

Jan 1, 1976

By Irving Hartmann, Bernard Lewis, John Nagy, H. P. Greenwald, H. C. Howarth

"ORIGIN OF INVESTIGATIONThe Federal Mine Safety Code for Bituminous Coal and Lignite Mines of the United States, July 24J 1946, contains the following provisions with regard to rock dusting: Article VI. - Section 2. Rock dusting.(a) All mines, except those mines or those locations in a mine which are too wet or too high in incombustible content to propagate an explosion, shall be rock-dusted to within 80 feet of the faces of rooms and entries; however, if the mine or any part of it is wet but becomes dry, the mine or portion of the mine so affected shall be rock-dusted as ·soon as it becomes dry. (b) In mines partially rock-dusted or in mines that are required to start rock dusting, haulageways and parallel entries connected thereto by open crosscuts shall be rock-dusted. Back entries shall be rock-dusted for at least 1,000 feet outby the junction with the first active entry. Inby this junction, the rooms, entries, and crosscuts shall be rock-dusted by generalized rock dusting as provided for in section 2(a).(c) Where rock dust is applied, it shall be distributed upon the top, floor, and sides of all open places and maintained in such quantity that the incombustible content of the mine dust will not be less than 65 percent. In trackless entries and air courses, protection in lieu of generalized rock dusting may be had by using bags filled with rock dust, if they are placed at regular intervals and staggered as described in Bureau of Mines Report of Investigations 3411."

Feb 1, 1948

By H. W. Wainwright

1. A schematic diagram and a description of the apparatus are presented. 2. Five runs were made using gas having a hydrogen-carbon monoxide ratio of about 2:1 and sulfur concentrations ranging from nil to 1.53 grains per 100 std. c.f. 3. At constant space velocity of synthesis gas the product of the sulfur concentration and days of operation, with conversion of H2 + CO above 97 percent, was constant. With a gas containing 0.04 grain of sulfur ac carbonyl sulfide per 100 std, cu. ft ,, the conversion of H2 + CO remained over 97 percent for 40 days. During that time the heating value of the product gas (on a C02-free basis) remained relatively constant at 940 B .t .u. per c.f., based on dry gas measured at 600 F. and 30 inches Hg.

Jan 1, 1954

By Lynn L. Rethi, Barbara Fotta

Recent employment figures (taken from the Mine Safety and Health Administration's database) indicate that the number of independent contractor' employees working in the coal mining industry has doubled over the past ten years. As their numbers increase, they become a more visible segment of the industry. [ ] Increased exposure to mining hazards has also brought an increase in the number of fatalities involving independent contractor workers. One gauge that is traditionally used to evaluate the overall safety of an entity is the "number of fatalities." Over the five-year period from 1985-89, 27 independent contractor employees were fatally injured while working on coal mine property. This number increased to 45 fatalities during the subsequent five-year period from 1990-94. Nearly half of these fatalities (47%) were due to accidents involving powered haulage (See Table); 13% were electrical accidents; and 9% were machinery accidents. Combined, these three accident classifications accounted for 69% of all coal nine independent contractor fatalities. Information taken from fatality data is an important piece of the safety puzzle; however, other variables need to he examined in order to better define contributing factors associated with accidents. More specifically, information on trends in fatal and nonfatal accident and injury data is necessary before deciding what approach should be used to improve safety. In order to implement appropriate safety strategies, it is important for safety practitioners to examine all available lost time accident and injury information. The following coal industry data sites specific and present trends of independent contractor employees working in underground locations at coal mines, surface areas of underground coal mines, surface coal mines, and preparation plants. The data compares employment and accidents for time periods at the beginning and the end of a ten-year span from 1985 to 1994. Because the number of incidents involving independent contractors in certain accident categories during any one year may be small, three-year totals are used; the first three years (1985-87) of the ten-year period are compared with the last three years (1992-94). [ ]

By J. B. Gayle

This investigation was conducted by the Federal Bureau of Mines to compare the selectivities of diverse flotation reagents and also of flotation and float-sink methods of separation. Flotation tests, using sodium chloride, an alcohol-type frothing agent, and a kerosine-pine oil mixture as reagents, were made on seven coking-coal samples representing four different beds. The results indicated equivalent selectivities relative to sulfur rejection when entrapment effects were minimized by recleaning the various products. Selectivities relative to ash rejection were also equivalent for some coals; for others, the selectivities of the reagents tended to increase in the order sodium chloride, alcohol-type frother, and kerosine-pine oil. Float-sink tests on these same coals generally gave results indicating better selectivities than those obtained in flotation tests at comparable levels of recovery.

Jan 1, 1960