Search Documents

By Irving Hartmann

Modern mechanized mining with high-speed machines, multiple-entry systems, multiple blasting, high-velocity air currents, and rapid haulage has brought many economic benefits and has on the whole enhanced safety in the coal-mining industry. It has, however, also introduced some added hazards, the control of which requires concerted effort and ingenuity. Mechanized mining has greatly increased the production and dissemination of fine coal seam or in mine entries. Use of high-speed machines has increased the probability of formation of incendive sparks, which are produced by frictional contact between moving metals and certain mineral substances in the coal seam or in the adjoining rock strata. In gassy seams rapid extraction of coal has increased the rate of gas evolution. These facts have made more urgent the need of preventing the ignition of coal dust and the development of widespread mine explosions. The ignition hazard can be controlled best by eliminating all potential igniting sources and by careful attention to ventilation designed to prevent accumulation of gas capable of triggering a coal-dust explosion. Frictional spark ignition by mining machines and suggested safeguards are discussed in a recent publication. Extensive research and long experience have shown conclusively that the propagation of coal-dust flames can be arrested and the development of widespread explosions prevented by properly applied, generalized rock dusting.

Jan 1, 1956

By A. Wahab Khair

"This paper deals with the description of the capabilities of a unique rotary coal cutting simulator which has been designed and fabricated at West Virginia University. It operates under the simulated mining conditions with in-situ stresses (horizontal and vertical stresses) being applied to a coal block of 18 in. x 15 in . x 6 in located in a suitably designed confining chamber. Cutting drum rotation can be varied from 1 to 40 rpm with the capability of stopping the drum after a predetermined number of rotations. Tests can be performed with four different bit angles, 15, 30, 45 and 60 degrees . A maximum of seven bits could be used in seven different orbits. Various cutting depths up to a maximum of 4 in. is possible.Monitoring devices constitute, Linear Variable Differential Transformers (LVDTs), pressure transducers, cascade Impactors, flow meters, flow controls and drum cutting speed. LVDTs are used to monitor the displacement of the coal block as well as the depth of cut. Pressure transducers are used to monitor the changes in pressure, both due to the thrust and due, to the intermittent cutting nature of the rotary cutting. Flow controls will be used to run the drum at a set rpm between 1 and 40 and to provide a different rate of advance. All the above mentioned devices can be operated and monitored by a fully automated control system. Six-stage cascade impactors are used to determine the mass distribution of dust along the rotation path of the drum. The fracture size, shape and Intensity can be studied by optical microscopy and the dust entrainment by using high speed photography.This equipment will basically be used to study the fracture mechanism in coal, associated with operating and in-situ parameters and further relate It to dust generation and entrainment In underground coal mines."

Jan 1, 1988

By Victor J. Lynch

The Andover-Sulphur Hill mines are 12 miles northeast of Andover and 5 miles southeast of Newton, in Sussex County, N.J. The property is situated on the Lehigh Valley and Hudson River Railroad and half a mile east of U.S. Highway 206. It is connected with the main highway by a hard-surfaced county road. (See fig. 1.) Howard J. Hewitt of Lafayette, N.J., has under lease the Sulphur Hill tract, consisting of 28 acres, and has an option on the Tar Hill tract of 106 acres. The Tar Hill property adjoins the Sulphur Hill on the northeast. (See fig. 2.) The Andover-Sulphur Hill property is owned by the Lenape Corp. of Andover, N.J., while the Tar Hill tract is owned by the Crane Iron Co. of Phillipsburg, N.J. These mines produced iron ore during a period of about 100 years but have not been operated since 1880. Zinc and lead sulfides occur mixed with iron ores in the lower workings of the old mines. A diamond-drilling program was recommended to determine the extent of the sulfide mineralization in depth and also to explore further the iron-ore deposits on the property. The project was started October 6, 1942, and finished November 25, 1942.

Dec 1, 1947

By W. P. Yant

Canister-type gas masks have become an essential part of the equipment of many industries not only for use in emergencies, but also in performing normal operations of industrial processes and procedures, particularly where ventilation is not practically or economically feasible. They are also used widely for enhancing safety of operations which previous to the development of gas masks had been performed in harmful atmospheres. Since the inception of industrial gas masks the Bureau of Mines has been actively engaged in endeavoring to increase the efficiency and safety of these devices and this bureau has become a source of advice to manufacturers in producing devices of good quality and to industry in the proper selection and use of these devices. In order to give first-hand information and keep current with the demands and needs of industry it is necessary to perform investigations from time to time. This report deals with tests of certain types of commercial gas-mask canisters for protection against mercury vapor.

Jan 1, 1932

By Alla D. Mah

The energies of combustion of zirconium carbide and hafnium carbide were measured by combustion calorimetry and the heats of combustion and formation. of zirconium carbide and hafnium carbide were derived . The results are-- ZrC AH298.15 ( combustion) = -308.60 ± 0.55 kcal /mole , AH298.15 ( formation) -47.0 ± 0.6 kcal /mole , AH298.15 = HfC (combustion ) = -306.08 ± 0.20 kcal/mole , AH298.15 ( formation) -52.3 ± 0.4 kcal /mole . = INTRODUCTION This report contains the results of calorimetric measurements to obtain the heats of formation of zirconium carbide ( ZrC) and hafnium carbide ( HfC) . The work was conducted as part of a Bureau of Mines program for determining the heats of formation of oxides , carbides , and nitrides by combustion calorimetry . Combustion calorimetry is one of the most precise calorimetric techniques . The chief obstacle to obtaining accurate heat of formation values for carbides , and the chief reason for the variation in the results of different investigators , is the lack of purity of the carbide samples . Corrections for impurities always involve assumptions which lead to uncertainties . In general , a large impurity correction is accompanied by a large uncertainty in the final result .

Jan 1, 1964

By M. J. Brnich

The purpose of this U.S. Bureau of Mines study was to assess the ability of trainees to don an unfamiliar self-contained self-rescuer (SCSR) after having become familiar with how to put on a different type of apparatus. Prepractice instruction was the same for all individuals learning to put on a device: a step-by-step, hands-on talk-through using the "3+3" method. Subjects were assigned to groups that had their initial donning instruction delivered on either the Draeger OXY-SR60B or the CSE SR-100. Trainees' performances were then evaluated using the other model. Donning trials were analyzed using a number of measures. It was found that SCSR design had a moderate influence upon how well the donning task transferred.

Jan 1, 2010

By M. G. Zabetakis

At ordinary temperatures and pressures methyl ethyl ketone (MEK)-air mixtures containing between 2.0 and 11 vol.-pct. MEK and methyl isobutyl ketone (MIBK)-air mixtures containing between 1.5 and 7.5 vol.-pct. MIBK are flammable. However, MEK-bromochloromethane (BCM)-air mixtures containing at least 6.2 vol.-pct. BCM and MIBK-BCM-air mixtures containing at least 7.0 vol.-pct. BCM are nonflammable. Also, MEK-BCM-air and MIBK-BCM-air mixtures containing less than 18.7 vol.-pct. oxygen are nonflammable. To assure the formation of nonflammable mixtures when mixed with air, MEK-BCM vapor mixtures must contain at least 1.6 vol. BCM per volume MEK, and MIBK-BCM vapor mixtures must contain at least 2.8 vol. BCM per volume of MIBK; these quantities of BCM would be produced by liquid mixtures containing 55 vol.-pct. BCM in the first case and 60 vol.-pct. in the second. An MIBK-BCM-trimethylene chlorobromide mixture containing equal volumes of each liquid forms nonflammable mixtures with air at ordinary temperatures and pressures. The same is true of a liquid mixture containing 34.6 pct. (liquid volume) BCM, 34.b pct. perchloroethylene, 15.4 pct. MIBK, 7.7 pct. toluene, 3.85 pct. ethyl amyl ketone, and 3.85 pct. trimethylene bromide.

Jan 1, 1960

This report summarizes the work performed by the Bureau of Mines on the development of analytical procedures for determining metallic and interstitial impurities in high-purity tungsten. Fourteen published methods and seven unpublished methods are briefly described. Carbon, hydrogen, nitrogen, and oxygen, in microgram to higher quantity levels, can be determined by several methods. Trace levels of 29 metallic impurity elements can be determined by optical spectrography, X-ray spectrography, and other instrumental methods.

Jan 1, 1968

By Foster Fraas

Review of the literature on solid solutions discloses that the relation between composition and magnetic susceptibility is not linear . Recalculation using a transformation of composition values to parameter v values provides for a linear relation with the magnetic susceptibility to the 1/2 power . Application to minerals is illustrated by the olivine and enstentite series .

Jan 1, 1964

By Suresh K. Bhatt, Gary L. Mowrey, Timothy R. Rehak, David K. Ingram

Coal and nonmetal mining used about 4.3 billion pounds of explosives and blasting agents during 2001 in the United States. A major part of this consumption was related to surface mining. Mine Safety and Health Administration accident data indicate that flyrock and lack of blast area security were the primary causes of blasting-related injuries in surface mining. Fatal injuries due to lack of blast area security were primarily caused by failure to clear blast area or inadequate access control to the blast area. At a coal mine, a neighbor walked into the blast area and was fatally injured. The blaster could not see the victim entering the blast area from the firing station. In another case, a passenger in a vehicle was fatally injured by flyrock because highway traffic was not monitored during the blast. In another example, a dozer operator entered a blast area due to lack of access control. Several fatalities resulted from using inadequate or no blasting shelter. A crane operator was fatally injured while standing in the open about 120 ft from the blast site. In another instance, a helper, standing about 150 ft away from the edge of a blast, was fatally injured by flyrock. In a limestone mine an equipment operator was fatally injured while guarding access roads in a pickup truck. This paper briefly describes six representative fatalities due to flyrock and lack of blast area security in coal and nonmetal mines. Several mines were visited to collect information relative to working practices aimed at mitigating blasting hazards. Salient information obtained through these visits is presented.

By C. L. Klingman

In extracting helium from natural gas at Bureau of Mines helium plants, a continuous analysis of the helium content of inlet and outlet gas streams is required to determine extraction efficiency. An analyzer, using established principles of gas chromatography to effect the analysis, has been developed by the Bureau of Mines to meet this need. It will record the helium content of inlet or discharge gases from helium-extraction plants every five minutes, continuously, without the attendance of an operator. A 25-inch column of activated charcoal is used as a partitioning agent; nitrogen is the carrier gas; and a hot-wire, thermal-conductivity cell is the detector. A 1.0 mv, strip chart indicates the unbalance of the detector cell, Sample size is 0.37 cc, and carrier gas flow rate is 75 cc, per minute. Significant improvements in helium extraction have been demonstrated by using the chromatograph in three helium-extraction plants.

Jan 1, 1961

By W. E. Wallace, B. L. Razzaboni, P. Bolsaitis, M. J. Keane

"Therma1 and chemical treatment of respirable size silica dusts samples is shown to induce marked changes in their hemolytic activity. The cytotoxicity of crystalline a-quartz (Min-U-Sil), and fumed silica (Cab-0- Sil) particles, as measured by a hemolytic activity protocol, is decreased by calcination and can be related to the dehydroxylation of the surface. The hemolytic activity of P-cristobalite particles of respirable dust si7.e was also determined and found to be lower than that of a-quartz. The change in the surface structure resulting from thermal treatment is detectable by photo-acoustic infrared spectroscopy and zeta-potential measurements. The absorption band in the 3200-4000 cm-1 frequency region of both Cab-0-Sil and MinU- Sil disappears upon heat treatment while a sharp band, identified with single silanol groups, at 3750 cm-1 increases in intensity. The zeta potential-pH profile, in the pH range of 4.0-7 .0, of the calcined, siloxane surfaced particles is more negative than that of material with a silanol surface.The cytotoxicity of the crystalline and fumed silica dusts was also found to be strongly dependent on particle size. Fumed silica of large surface area (small particle size) exhibits an initial increase in hemolytic activity upon calcination. This result confirms other experimental observations pointing to a particle size of maximum toxicity. INTRODOCTIONThe toxicity of silica and other mineral particles, as manifested by their role in inducing pneumoconiosis, fibrosis, silicosis and other pulmonary disorders is largely traceable to the characteristics of particle surfaces and to particle morphology. The great wealth of data on the physical and chemical properties of silica is still insufficient for a comprehensive understanding of the specific parameters to be associated with fibrogenic activity and, correspondingly, with the optimum means for characterizing and quantifying the toxicity of dusts, and the design of possible preventive or therapeutic methods.The great diversity of parameters that have been proposed and tested for correlation with cytotoxicity suggest that more than one mechanism may be involved in the fibrotic activity of silica particles. The crystalline structure of the material (more active tridymite versus less active crisobalite and passive stishovite), freshly formed surfaces and free radicals associated therewith, silicic acid adsorbed onto silica surfaces, the concentration of hydroxyl groups at silica surfaces, particle size and morphology, among other properties, have been investigated and found to conelate in tests of cytotoxicity."

Jan 1, 1990

By M. C. Irani

The Bureau of Mines has designed and put into operation a fail-safe control system for use in underground coal mines equipped with methane drainage pipelines. This control system can detect certain unsafe conditions and respond by automatically shutting off the flow of methane from the degasification borehole to the drainage pipeline. Methane flow is shut off when the methane content in the return airways reaches a predetermined level (typically 1.5 pct), when the methane drainage pipeline is ruptured by roof fall, or when there is an electric power failure. The fail-safe control system was designed using commercially available components and a methane analyzer system previously developed by the Bureau. The fail-safe system consists of a unit that combines a shutoff valve and pneumatic valve actuator, and electronic and mechanical equipment designed to detect hazards and effect shutdown. The fail-safe control system was designed to meet regulatory requirements issued by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, and State regulatory bodies for the safe operation of underground methane pipelines used for mine degasification. MSHA has inspected and tested this system and permitted its use in two mines. The Bureau installed the fail-safe system in two working coal mines, where successful performance has been demonstrated.

Jan 1, 1979

By P. W. Jeran, S. J. Pepperney, M. C. Irani, F. F. Kopsch

The Bureau of Mines has designed and put into operation a fail-safe control system for use in underground coal mines equipped with methane drainage pipelines. This control system can detect certain unsafe conditions and respond by automatically shutting off the flow of methane from the degasification borehole to the drainage pipeline. Methane flow is shut off when the methane content in the return airways reaches a predetermined level (typically 1.5 pct), when the methane drainage pipeline is ruptured by roof fall, or when there is an electric power failure. The fail-safe control system was designed using commercially available components and a methane analyzer system previously developed by the Bureau. The fail-safe system consists of a unit that combines a shutoff valve and pneumatic valve actuator, and electronic and mechanical equipment designed to detect hazards and effect shutdown. The fail-safe control system was designed to meet regulatory requirements issued by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, and State regulatory bodies for the safe operation of underground methane pipelines used for mine degasification. MSHA has inspected and tested this system and permitted its use in two mines. The Bureau installed the fail-safe system in two working coal mines, where successful performance has been demonstrated.

Jan 1, 1980

Reduce costs of surface mine reclamation by improving bulldozer operating efficiency. Approach A draft power indicating system helps bulldozer operators adjust blade height and other controls for maximum load movement, by continuously indicating the rate at which work is being done. How It Works This system continuously measures both the push of the blade against the overburden, and the true ground velocity of the bulldozer. It multiplies those quantities to determine the real work rate of the machine. The system consists of a velocity sensor, a blade load sensor, processing circuits, and a work-rate indicator. The processing circuits include an analog multiplier which has an output signal representing the draft power (velocity x load = power). The draft power, or pushing power is a measurement of the work rate at that moment.

Jan 1, 1979

By N. E. Hanna

An important goal in the development of coal mining explosives has been to improve their safety characteristics through suitable formulation. In the United States no systematic effort to establish factors influencing the incendivity to firedamp and to coal dust of explosives through research was made until the last decade. In consequence, American permissible explosives underwent only very slight modifications and many remained substantially the same as in the early years. As part of a long range program for increasing the safety of permissible explosives, the Bureau of Mines undertook to determine how the amounts and particle sizes of the principal constituents of these explosives affect their incendivity. It was found that an increase in the relative amount of sodium chloride and a decrease in its particle size significantly decreased the incendivity of our permissible explosives to firedamp (7-9).6 This is in agreement with findings reported by Dolan (4) for compositions of nitroglycerin and salt. One important result of the work at the Bruceton station has been the recent introduction of salt-formulated permissibles by several explosives manufacturers. This paper describes a statistically designed experiment for studying the effects of the particle size of ammonium nitrate and the type of carbonaceous materials used on the incendivity of permissible explosives. Interest in these particular effects goes back as far as the first formulations of coal mine explosives, around 1910 in the United States and even earlier in Great Britain and other countries. Although it is well established that fine

Jan 1, 1961

By H. H. Schrenk

There are several well-recognized procedures for controlling exposure to hazardous atmospheres in industry. They include (a) substitution of less toxic material, (b) enclosure of processes, (c) wet methods, (d) local exhaust, (e) general ventilation, and (f) use of respiratory protective devices. In addition to their employment as a control measure in occupational exposures, respiratory protective devices also are essential in emergencies that may arise from failure or improper use of other control equipment. Respiratory protective devices usually are employed to supplement other methods of control, as temporary expedients, or when other methods are not readily applicable or practicable. It seems reasonable to assume, however, that where respirators are used consideration has been given to the factors involved and that the devices can provide satisfactory protection if used properly. Their use should not be arrived at simply by a process of elimination of other methods that are more difficult to apply.

Jan 1, 1943

By I. Iwasaki

In recent years the rapid depletion of high-grade iron ores and the demand by blast furnace operators for increasingly low-silica ores have stimulated interest in flotation studies of low-grade iron ores, such as wash-ore tailings and oxidized taconites. Four processes have been reported for the flotation separation of these iron ores--anionic and cationic collection of the iron oxides, cationic collection of siliceous gangue, and anionic collection of activated siliceous gangue (5).5/ The effectiveness of any one method, however, depends largely on the mineralogical composition and on the physical structure of the sample; hence, a comprehensive study of the floatability of the individual minerals occurring in these materials is essential. A review of the literature shows that the floatability of hematite and magnetite has been frequently investigated, whereas very little corresponding information is available for goethite, or for its more earthy form, limonite, both of which are abundant in the Mesabi and Cuyuna ores (19). The purpose of this investigation was to formulate general information on the floatability of goethite. Vacuum flotation, contact angle measurement, and simplified flotation tests using a modified Hallimond tube were used. The experimental results were correlated with the electrokinetic properties of goethite as determined by streaming potential measurement. The results were used to interpret the batch flotation tests made on an artificial mixture of quartz and goethite.

Jan 1, 1960

By Ellsworth R. Spencer

A lightweight fiberglass feed leg for hand-held pneumatic percussion rock drills has been fabricated and tested by the Bureau of Mines. Its lighter weight facilitates easier handling of the rock drill apparatus, thereby reducing the potential for back injury to the driller and in- creasing drilling productivity. Current hand-held feed leg drills of the same class are 50 pct heavier than the Bureau-devised feed leg drill, which is comprised of a reduced-noise drill and the fiberglass feed leg. In-mine tests of the fiberglass leg showed that its performance and cost are comparable to those of standard aluminum feed legs.

Jan 1, 1985

Objective: To enable mine operators and mine inspectors to make quick and accurate measurements of the explosible nature of coal and rock dust mixtures.

Jul 1, 2008