Search Documents

Investigate and demonstrate the possible use of low-density (45-lb/ft3) foam concrete for sealing abandoned mine openings. Although foam concrete has been used in the construction and geotechnical industries for some decades, it has not previously been used in abandoned mint shaft reclamation. Approach A structurally engineered permanent mine seal for an abandoned coal mine shaft, using low-density foam concrete and other appropriate structural materials, was designed by the Bureau and installed at a field site, the No. 22 Shall in Logan County, West Virginia. The field work was conducted by a private contractor under the supervision of the West Virginia AML Section (WV AML). The No. 22 Shaft is situated immediately adjacent to a frequently traveled county road. A few feet away from the shaft is a branch of Pine Creek. On the other side of the road is a railroad line that serves an active mining operation located several miles away. The shaft measures 9.5 by 9 feet in cross section and is about 300 feet deep. It was used at one time as a dewatering shaft and still contains two large-diameter dewatering pipes with steel drive shafts inside them. Before the beginning of the reclamation, the shaft included a concrete cap a few inches thick, with a 4 - by 5-foot access opening covered by a steel grate. The interior of the shaft was quite humid, and considerable flow of water at the bottom of the shaft could clearly be heard from the surface. Methane tests were conducted that showed the shaft to be clear of this gas.

Jan 1, 1992

Metals From Oil Shale. -A Geological Survey News Release in mid-January indicated that a surface sample analysis of oil shale in central Montana found a ton of shale to contain up to 13 pounds of zinc, 2 pounds of nickel, 1.8 pounds of molybdenum, 16 pounds of vanadium oxide, and nearly a quarter pound of selenium. It might be possible to recover some of these metals economically on a byproduct basis. The shale in central Montana was also estimated to contain 180 billion barrels of synthetic crude oil, which compares to estimated oil reserves in the Middle East of 360 billion barrels. Merchant Fleet Dwindles. -The National Maritime Council reports that although the U.S. is the world's largest trading power and that well over 90% of its foreign trade is conducted by shipping, the U.S. fleet is tenth in absolute numbers and less than 5% of its foreign trade is carried on U.S. ships. In 30 years, the U.S. fleet has dwindled from over 4,000 oceangoing vessels to about 600. U.S. ships carry less than 2% of imported iron ore, bauxite, and tungsten, and only 3% of oil imports.

Jan 1, 1981

By Thomas E. Marshall, Timothy Batchler, Anthony T. Iannacchione

As the amount of new fractured surfaces or "damaged rock layers" within roof rock increases, the stability of the rock mass decreases. While direct measurements of this phenomenon are not easily made, there is good circumstantial evidence to support this hypothesis. For example, it is common to observe increased cracks or fractures in the immediate mine roof rock before a roof fall. Likewise, roof drill holes placed in areas that later fail often reveal increased numbers and/or separations of fractures within the rock column through time. And finally, the frequency of microseismic activity, representative of rock fracturing, increases before a roof fall. For this study, more than 700 microseismic emissions were collected from two underground limestone mine roof fall areas in southwestern Pennsylvania. Microseismic events were located and magnitudes determined using the moment magnitude technique. Moment magnitude is based on the event seismic moment, which is a measure of the seismic deformation. The amount of new fracture surface length was calculated based on the stored strain energy within the rock prior to fracture. In the two case studies presented, a significant amount of microseismic activity was observed as much as two days before the first signs of failure in the roof fall areas. Additionally, results from this analysis reveal much about the behavior of strata prone to failure and allows for the construction of hazard maps based on microseismic emissions. The potential use of this technique as a means of anticipating roof falls is analyzed and discussed.

By R. T. Stull, G. A. Bole

Previous Work . The Bureau of Mines reported a survey of bond clays for graphite crucibles at the American Mining Congress which met at St. Louis in November , 1919 *** . The report contained information in regard to : (a) tests carried on to determine the effect of substituting Canadian and Alabama graphites for Ceylon graphite in varying proportions . The data indicated that Alabama graphite is superior to Canadian graphite and further , that Alabama can be substituted for Ceylon graphite to a large measure without lowering the quality of the ware . These tests were made on No. 70 size brass melting crucibles and were carried out under foundry practice . (b ) Tests were reported in which an attempt was made to modify the nature of Alabama graphite by heat treatment so as to resemble Ceylon graphite . Little advantage from the treatment was reported . With this general information as a basis , the experimental work proceeded along two lines : A study of bond clays for steel -melting crucibles and for brass -melting crucibles . Twenty- one sets of standard-size crucibles were made up of a body containing Ceylon graphite as standard , bonded with 21 bond clays . These tests were carried out under foundry practice as were the former tests . Three domestic clays proved to be superior to the standard Klingenberg clay formerly used in brass -melting practice while in the steel - melting industry , 13 domestic clays gave service superior to Klingenberg clay .

Aug 1, 1923

By James J. Olson

The Bureau of Mines recorded and analyzed overpressure levels for three production blasts at the White Pine copper mine, Upper Michigan, to obtain representative data from single-heading blasts in a long, straight haulageway and to estimate the damage potential inherent in production blasts fired in close proximity to underground structures. Commercial pressure gages with a flat response to 1 kHz were used with an FM tape recorder to record the overpressures from one dynamite and two AN-FO (ammonium nitrate-fuel oil), 500-msec production blasts having zero-delay charge weights of about 75 lb (34 kg). The recorded waveforms from the underground blasts (1) were more complex than the typical free-air wave, (2) were of longer duration, and (3) had numerous secondary arrivals due to reflections from the ribs and roof. The waveforms showed that the zero-delay charges produced the only high overpressures. First pulse peak overpressures from the blasts ranged from 0.10 lb/in2 (6.9 X 102 N/m2) at a distance of 471.1 ft (144 m) to a maximum of 1.76 lb/in2 (121.3 X 102 N/m2) at 191,7 ft (58.4m) from the blasts. An analysis of variance of the first pulse overpressures from the three White Pine blasts showed that no statistically significant difference existed among the overpressure levels from the dynamite and AN-FO blasts and that a single equation P = 4.9 x 103 (D /W1 / 3) 2 .15, where P = overpressure in pounds/inch2, D = d-stance from the blast in feet, and W = zero-delay charge weight in pounds, could be used to describe the falloff of overpressure with distance.

Jan 1, 1971

Volumetric measures [ ]

Jan 1, 1962

1. In 2001, a total of 7,131 sand and gravel mining operations reported employment statistics to the Mine Safety and Health Administration (MSHA). Sand and gravel mines comprised 48.8% of all mining operations, the largest percentage of all mining sectors. Sand and gravel mines are distributed throughout all 50 states. The median number of operator employees per sand and gravel mine was 3.0.

Jul 1, 2003

By E. R. Bauer

The U.S. Bureau of Mines is investigating strata interactions associated with mining of multiple coal beds to provide the mining industry with improved methods of planning and developing multiple coalbeds, conserving resources, and increasing the safety of underground coal mining. This study involves analytical predictions and underground observations of longwall development ground control problems at a south-central Pennsylvania coal mine affected by subsidence induced by multiple-seam mining. As predicted, strata interactions were found in upper mine areas mined over lower mine gob. Observations revealed roof deterioration accompanied by excessive water inflows in the first 170 ft after crossing the gob line as mining entered and exited the subsided area (over the lower mine gob). In contrast, superimposed mine areas and areas mined a substantial distance out over the gob showed no signs of interaction with previous lower seam mining, again as predicted.

Jan 1, 2010

1. In 2003, a total of 4,357 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA). The major industrial classifications in stone mining are dimension stone (used for construction purposes), crushed and broken stone (aggregates), cement, and lime. • Stone mines comprised 30.3% of all mining operations. • Mines producing crushed and broken stone (n = 3,412) comprised 78.3% of all stone mining operations.

Feb 1, 2005

By R. R. Schehl

The Bureau of Mines has developed a quantitative Analysis for pyrite in coal by X-ray diffraction that can be accomplished in little more than 1 hour. To minimize the sample analysis time, data processing has been completely computerized with pertinent output information displayed on a VR12 cathode-ray tube display. Use of this computerized system is not only advantageous during the experimental stages of the pyrite analysis project but would also be essential if the X-ray diffraction procedure is accepted as a standard method of analysis.

Jan 1, 1973

By W. S. Landers

Analysis of the size consist of broken coal has been extended in recent years beyond the mere representation of the relative quantities of the various sizes present in a given lot of the material. Fundamental characteristics of the coal related to the process of breakage fix the distribution of sizes, and it has been found by Rosin and Rammler4/ that a relatively simple law-governs this property. Benhett5/ has described a graphical method of expressing the relationship, and by its use considerable simplification in the expression of size distribution is possible.

Jan 1, 1946

By J. H. Perry

The Bureau of Mines is conducting research to determine the effectiveness of long holes in degasifying an area of the Upper Split of the Lower Sunnyside coalbed at Kaiser Steel Co.'s Sunnyside No.1 mine. These holes were drilled from the two outside entries of a section that was closed to mining because of excessive methane emissions. Two holes drilled to 430 and 450 feet produced initial gas flows of 160,000 and 127,000 cfd, respectively. Sixteen days after the completion of the second hole, the total gas production declined to just over 144,000 cfd. In 9 months of degasification, over 35 MMcf of commercial-quality gas has been removed from the coalbed. The combined gas flows declined to 106,000 cfd in the 9-month period. The two holes have reduced face emissions by about 40 pet.

Jan 1, 1978

By N. B. Greninger

The U.S. Bureau of Mines conducted explosion tests on various full-scale cementitious bulkheads used in abandoned mine areas to evaluate the ability of the bulkheads to withstand gas explosion over-pressures of 20 psig. Tests were performed on 120-ft2 solid-concrete-block seals of varying thicknesses and designs. Of the seven solid-concrete-block seals tested, only the standard-type seal, having a 16-in thickness, keyed at the floor and ribs, all joints mortared, wedged at the roof, and a center pilaster, maintained its integrity when subjected to a 20-psig pressure wave. After being subjected to repeated explosions, the standard seal only showed a small hairline crack and had an air leakage of 87 ft3/min at a pressure differential of 1 in H2O. Tests were performed on cementitious foam seals of varying thicknesses and compressive strengths. Explosion tests have shown that 200-psi strength, 4-and 8-ft-thick seals can withstand a 20-psig pressure wave. At a pressure differential of 1 in H20, no air leakage was detected through the 200-psi, 8-ft-thick foam seal.

Jan 1, 2010

By Noel N. Moebs

The Bureau of Mines conducted five reconnaissance magnetometer traverses across a small abandoned chromite mine in the State Line district of Pennsylvania and Maryland to determine the geophysical response of the area. The results indicate that more extensive geophysical surveys of the region might establish some worthwhile guidelines for chromite exploration. While chromite only rarely can be detected directly by magnetic methods, there is a possibility that geophysical signatures in the adjacent host rock could provide some guidelines for further exploration. Prior to 1875, all the chromite produced in the United States came from the State Line district, and the potential for discovering additional podiform deposits could be significant. Virtually no state-of-the-art geuphysical or geochemical studies have been conducted in this district since World War II and sizable areas remain undeveloped and suitable for exploration. While the results reported in this paper are not supported by drilling, it may encourage others to investigate the area more fully for improved methods of detecting subsurface podiform chromite deposits. New theories on the emplacement of ophiolites also could contribute to an assessment of the chromite potential of the serpentinite belt.

Jan 1, 1991

By Barbara J. Halpern

There?s no denying that mining is a male-dominated industry. Yet thanks to technologies developed over the last 20 years, societal changes in sex role stereotyping, individual determi­nation, and the willingness of companies to train women, there are no jobs in mining today where women are not represented. Women are drillers and electricians as well as drivers of heavy equipment and haulpack trucks. They perform jobs ranging from field exploration and metallurgy to clerical and janitorial and warehousing positions, from prospectors and underground blasters to geologists and land reclamation experts, from communicators to legal experts on mining law and more. The Women?s Mining Coalition, founded in 1994 to shepherd responsible legislative mining reform, estimates that 20 percent of the workers in the mining industry are women. Although women are concentrated in clerical and adminis­trative jobs, at least 10 percent are in non-traditional, hardhat jobs, claims the group. There are women in management, but the numbers in senior management remain small, especially in larger companies.

Feb 1, 1998

By N. S. Dalal, V. Castranova, K. Van Dyke, V. Vallyathan

"IntroductionInhalation of crystalline silica is often associated with the development of pulmonary disease (Ziskind et al., 1976). Recently, it has been proposed that freshly sheared silica .may have surface properties that make it more reactive with lung tissue than aged silica, and that this unique reactivity ·of freshly crushed silica enhances its pathogenicity. A recent study in our laboratory strongly supports this theory (Vallyathan, et al., 1988a; 1988b). We found that grinding of silica cleaves bonds in a silica tetrahedral lattice generating reactive free radicals sites on the surface of the silica particles. The presence of surface radicals on freshly ground silica was monitored by electron spin resonance (ESR) spectroscopy. The ESR signal generated from fresh silica in air is characteristic of Si-0 and Si radicals. Evidence, i.e., the ESR signal after the addition of a spin trap (DMPO) and its sensitivity to ethanol, indicates that these silicon-based surface radicals can react with water to form hydroxyl radicals (OH). Results also indicate that these surface radicals make fresh silica more cytotoxic than aged silica; i.e., fresh silica causes more membrane damage as evidenced by hemolysis and lipid peroxidation. Therefore, the presence of reactive sites on the surface of freshly cleaved silica may play a significant role in its pathogenicity.If surface· free radicals are related to cytotoxicity, then screening dusts for the existence of such radicals may predict their relative pathogenicity. Since an ESR spectrometer is not available to many laboratories, the objective of this study was to develop a quick and simple technique to monitor the existence of reactive surface sites on dust. The technique chosen was the measurement of chemiluminescence using a liquid scintillation counter; i.e., an instrument which·would be accessible to most investigators."

Jan 1, 1989

By W. Bruce Montgomery

Manganese oxides occur, with some iron oxides, in small scattered lenses on property controlled by the Columbia Manganese Co. (1943) near Evington, Campbell County, Va. The company mined some manganese ore during 1917 and 1918. A preliminary examination in May 1942 indicated the possibility of finding additional ore. On August 21, 1942, the Bureau of Mines began prospecting to verify the continuity of the ore exposures. Work on this project continued until February 5, 1943. Prospecting and development work included shaft sinking, crosscutting, drifting, trenching, and test-pitting in six separate areas indicating two types of deposits. The most predominant type is a wide brecciated area in which occur lenses or pockets of nodular manganese oxides. The other type is characterized by more of a vein structure, including thin layers of manganese oxides.

Jan 1, 1949

By T. O. Llewellyn

The Bureau of Mines, as part of its goal to develop technology that can conserve domestic mineral resources investigated beneficiation methods for recovering phosphate minerals from two Southern Florida deposits with high magnesium content. Chemical analyses of sized fractions indicated that no coarse pebble concentrate could be produced from either deposit. Conventional fatty acid-fuel oil batch flotation tests on two phosphate samples, analyzing 6.8 and 8.5 pct P205, yielded concentrates containing 28.97 to 29.80 pct P20S at recoveries ranging from 72.4 to 76.9 pct of the flotation feed. The MgO content ranged from 1.20 to 1.36 pct. Bubbling S02 gas through an aqueous concentrate slurry, further reduced the MgO content of these phosphate concentrates to 0.5 and 0.8 pct, but with a concomitant loss in the phosphate recovery. Settling characteristics of slimes from both phosphate samples showed a slow settling rate, which is a typical characteristic of other slimes in the region.

Jan 1, 1981

By J. Gautam, T. Ong, W. E. Wallace, M. Keane, S. Xing, J. Harrison

"INTRODUCTIONOrganics extractable from respirable diesel exhaust soot particles by organic solvents have been known for some time to be direct acting frameshift mutagens in the Ames Salmonella typhimurium histidine reversion assay (Huisingh, et al). Upon deposition in a pulmonary alveolus or respiratory bronchiole, respirable diesel soot particles will contact first the hypophase which is coated by and laden with surfactants. To model interactions of soot and pulmonary surfactant, we dispersed soots in vitro in the primary phospholipid pulmonary surfactant dipalmitoyl glycerophosphorylcholine (lecithin) (DPL) in physiological saline. We have shown that diesel soots dispersed in lecithin surfactant can express mutagenic activity, in the Ames assay system using S. typhimurium TA98, comparable to that expressed by equal amounts of soot extracted by dichloromethane/ dimethylsulfoxide (DCM/DMSO)(Wallace, et al, 1987). Here we report additional data on the same system using additional exhaust soots and also using two other phospholipids, dipalmitoyl glycerophosphoryl ethanolamine (DPPE), and dipalmitoyl phosphatidic acid (DPPA), with different ionic character hydrophilic moieties. A preliminary study of the surfactant dispersed soot in an eucaryotic cell test system also is reported.MATERIALS AND METHODSSoots D4 and D6 were collected at two different times as scrapings from the exhaust pipe of a diesel tractor-trailer immediately after the engine was stopped. Surfactant dispersions were made by ultrasonic probe sonicating 25 mg of commercially obtained DPL, DPPE, or DPPA into 1O ml of O.85% physiological sterile saline (PSS) for 10 min at 40 watts power. For surfactant dispersions, 2.5 mg soot was mixed into 2.5 ml of the appropriate phospholipid dispersion. Mixtures were sonicated by 40 watts sonicator probe for one min, then incubated in the sonicator water bath for 30 min at room temperature; the mixture was then incubated for one hour at 37C while being rotated continuously. Dilution series were made with saline. For solvent extraction, 2.5 mg soot was mixed into 2.5 ml of DCM and incubated in a sonicator water bath for 30 min at room temperature. The sample was then mixed with 2.7 ml DMSO, placed in a dry bath at 45C, and the DCM evaporated under a stream of nitrogen gas until 2.5 ml of liquid remained. Ames salmonella/microsome assay utilizing TA98 for frameshift mutation was used for mutagenicity testing, with and without S9 activation, as described by Ames et al (1975). Unfiltered sample extractions or dispersions were preincubated with tester cells for 90 min at 37C : 0.1 ml of sample was mixed with 0.5 ml of PSS, or of S9 mixture, and 0.1 ml of an overnight TA98 culture incubated samples were then added to 2 ml of top agar supplemented with biotin and a trace amount of histidine, and overlayed onto Vogel-Bonner minimal media plates. After 48 hours incubation at 37C, revertant colonies were counted. Solvent controls were DMSO, DPL, DPPE, DPPA, and saline. Positive controls were trinitrofluorenone (1 ug/plate), for samples not treated with S9, and 2-aminoanthracene for S9 treated samples (2.5 ug/plate). All samples were assayed in duplicate. Sister chromatid exchange (SCE) assay was performed, following Lett, et al (1981), using V79 cells, of Chinese hamster pulmonary fibroblast origin. Stock diesel sample suspensions were made as 10 mg soot/ml DPL suspension, or 20 mg soot/ml in DMSO. Aliquots of these soot preparations were added to 15 ml of culture medium per sample flask to result in concentrations of 25, 50, and 75 ug soot/ml medium. After 12 hours incubation, 200 ul of 25 uM 5-bromodeoxyuridine (BrdU) was added to each flask. After another 35 hours incubation, 200 ul of 10 ug/ml colcemid were added; and the cells were harvested three hours later. Cells were swollen by hypotonic saline, and fixed twice with methanol/acetic acid, and burst on microscope slides. Cells on the slide were stained with Hoechst 33258, exp"

Jan 1, 1990

By A. F. Jolly

As a part of ongoing research into the sulfidation partitioning of selected complex minerals, the U.S. Bureau of Mines conducted research designed to selectively recover Cu from sulfidized chalcopyrite (CuFeS2). Ferric chloride (FeCI3) solutions leached >90 pct of the Cu and <20 pct (sometimes < 10 pct) of the Fe in the sulfidized concentrates. Cupric chloride (CuCI2) leaches were even more selective, solubilizing essentially 100 pct of the Cu and < 5 pct of the Fe. In contrast, leaching non-sulfidized CuFeS2 with either FeCl3 or CuCl2 showed that somewhat more Fe than Cu dissolved. These studies demonstrate that Cu is substantially more leachable from sulfidized CuFeS2 than from nonsulfidized CuFeS2? The Cu-and Fe-bearing constituents generated as sulfidation products, CuS (covellite) and FeS2 (pyrite), respectively, are differentially dissolved. The solubility of Fe from pyrite in sulfidized CuFeS2 is much lower than the solubility of Fe from complex nonsulfidized sulfide where Fe and Cu are bound in the same crystal lattice. Thus, the Cu dissolves selectively, producing a high-Cu filtrate from which Cu can be recovered by cementation or by electrolysis. Flotation of CuS-FeS2 mixtures indicates partitioned phases can be physically separated if effective liberation can be achieved. Magnetic separation tests yielded less promising results.

Jan 1, 1991