Search Documents

By M. A. Mahtab

This report describes the procedures used by the Bureau of Mines for obtaining attitudes of joints surveyed with a borescope in inclined boreholes. An algorithm for computing the dips and azimuths of the observed joints is presented. The algorithm is used to solve an example problem. A computer program based on the algorithm is listed. It is hoped that the procedures described here will be useful in treating large quantities of data obtained from comprehensive borehole surveys.

Jan 1, 1973

By L. A. Neumeier

The Bureau of Mines evaluated the properties and anisotropy in properties of rolled Zn-Cu and Zn-0.12 pct Ti-Cu alloys with various copper additions to 1.25 pct. The alloys were rolled cold and at various hot-rolling temperatures to reductions as high as 92 pct after breakdown rolling. The properties are extremely sensitive to various combinations of composition, rolling temperature, and rolling reduction, Zn-Cu alloys can develop good creep resistance, but they are inferior in that respect to Zn-Ti-Cu alloys. For alloys either with or without the titanium addition, cold-rolling results in recrystallization of the matrix and rejection of copper from solution, causing poor hardness, tensile, and creep properties, but high ductility. Peak tensile strengths develop when the alloys are rolled in the range 320° to 400° F, Best creep resistance for Zn-Cu alloys requires higher rolling temperatures when copper content is increased. Creep resistance is best for Zn-Ti-Cu alloys with about 0.75 to 1.0 pct CU rolled near 480° F. Some copper is soluble in the TiZn15 phase, which forms into "stringers" during rolling. The possible contributions to creep behavior of factors such as distribution of second-phase particles, grain size, and preferred orientation are discussed.

Jan 1, 1970

By W. C. Hudson

"The McLeod sand pits, on the northeast side of the Little Ocmulgee River in Wheeler County, Ga., opposite Lumber City in Telfair Co., were examined by the Bureau of Mines under its war program of Investigation of Critical and Essential Minerals. The pits are about a quarter of a mile above the bridge, which is half a mile above Lumber City. Mrs. A. T. McLeod of Lumber City owns the land, including the pits. The property was inspected by an engineer of the Bureau of nines on March 8, 1945, on recommendation of Capt. Garland Peyton, director, Division of nines, Mining, and Geology of Georgia.The Mcleod pits are at the northwestern extremity of a mile-long series of old pits that were worked from about 1900 until the 1920's. The burning of the spur railroad bridge connecting the pits with the Southern Railway at Lumber City stopped mining operations. The pits on the south-east, or opposite, side of the Glennwood Road from the McLeod pits were first worked by F. L. Hinson and later, in 1921, by Mrs. n. H. Mobley. The glass sand was shipped to Tallapoosa, Ga., and Chattanooga, Tenn., where it was used in the manufacture of bottles for soft drinks. Some of the sand was used as molding and construction material. The sand was mined by hand shoveling it into wheelbarrows, which were unloaded on freight cars. The pits were partly refilled with overburden, so that it is impossible to estimate even roughly the amount of sand excavated.Analyses of samples of glass sand made years age3/ and later in 19404/ roughly check those made by the Bureau of Mines laboratory, except that in the former the iron oxide content usually was greater, attaining a maximum of 0.72 percent.The sand pits are in a valley slightly more than a quarter of a mile wide that lies along the northeast side of the Little Ocmulgee River. The land is either flat or marked by ridges only a few feet high. . A rather thick growth of scrub trees covers most of the valley. The surrounding country consists of gently rolling farm lands. The altitude of the valley is not known, but, judging by its distance from the seashore, it probably is about 200 feet. In addition to the Glennwood highway, which crosses the valley, several old sand roads lead to the pits."

Apr 1, 1946

By Frank G. Horino

This report describes an instrument designed by the Bureau of Mines for quantitatively identifying texture of rock surfaces produced by grinding or extremely rough surfaces beyond the range of commercial surface measuring instruments. The transducer for the instrument is a linear variable differential transformer that converts mechanical motion caused by surface roughness, waviness, and lay to an electrical output. The electrical output is recorded graphically as an X-Y plot of the line traversed on the rock surface. Details of the synthesized device and its calibration are given. The sensitivity of the unit is 2 percent of the scale setting of the amplifier. The horizontal scale is adaptable from ¼ inch to 15 inches of specimen length with a sensitivity of 0.01 inch if a 10 to 1 magnification is used and 0.1 inch if a 1 to 1 magnification is used.

Jan 1, 1968

By D. L. Nussear, W. E. Wallace, N. N. Clark, M. Gautam, G. Hong-Guang

"Results from a study directed towards identifying and measuring the mutagenicity of diesel exhaust particulate matter involved in mining exposures, especially those which may synergistically affect genotoxic hazard, are presented in this paper. Particulate matter emissions from a diesel engine, representative of the ones found in underground mines, were sampled and assayed to determine the genotoxic potential as a function of engine operating conditions. Diesel exhaust was diluted in a multi-tube mini-dilution tunnel and the particulate matter was collected on 70 mm fluorocarbon coated glass fiber filters as well as on 8"" x 10"" hi-volume filters. A six mode steady state duty cycle was used to relate engine operating conditions to the mutagenicity potential.Protocols developed for using a primary component of pulmonary surfactant as a medium for collecting and applying respirable particulate material to cells for mutagenicity testing offer a true representation of in-vivo delivery of such respired aerosols to pulmonary cells and the genetic material within . The surfactant dispersion technique is discussed in this paper. Methods have been developed to sample and assay the diesel soot and diesel soot/mineral dust complexes which would not compromise the surface and physical properties of the particulate material."

Nov 1, 1995

By H. W. Leavenworth

Research was conducted by the Bureau of Mines to develop a technique to grow metallic fibers from a sulfide mineral. In this research, chalcopyrite (CuFeS2) was made sulfur deficient, and the remaining sulfur partitioned to the iron in the mineral to liberate metallic copper, or to the copper to liberate metallic iron. The metals formed on the surface as fibers and in the interior as spherical particles. Fiber growth is very fast. Lengths of 3 to 4 cm form in a matter of minutes, and the diameter of individual fibers is less than 1 µm. The mechanism of fiber growth is explained, and the reactions are reversible as predicted. Copper fibers can be made to grow from the surface at 400° C or to dissolve back onto the solid surface and be replaced by iron fibers at 625° C. Growth and dissolution can also be controlled to form copper/iron duplex fibers.

Jan 1, 1974

By Robert E. Dye

This paper describing the mining methods employed and setting forth prevailing, costs at the property, is one of a series being prepared by the United States Bureau of Mines dealing with properties in various mining districts of the United States and Canada. The Vipond mine is a gold property located at Timmins, Ontario, Canada, and operated by the Vipond Consolidated Mines (Ltd.). For the past fiscal year (ended July 31. 1930) ore was mined and milled at the rate of 310 tons per day, and the value of the bullion produced was $896,397.61.

Jan 1, 1931

By Arnold O. Tanner

The domestic mining industry continued to be strengthened and revitalized in 1989. The healthy conditions and the industry comeback that began in 1987 continued to spread and became more established for many commodities. Relatively comfortable and stable commodity prices, still found predominantly in the metals sector, reinforced other operational factors in bringing vitality to the mining and mineral processing industries. New streamlined business practices, mine and plant modernizations, and the progressive use of new technologies successfully helped lower operating costs and increase efficiency during the past 5 to 7 years. An element common to these three factors of industry renewal and growth was the ever-increasing infusion of and growing dependence on constantly advancing computer technology applications. This trend of increasing computerization was occurring throughout the mining and mineral processing business while it similarly was in most facets of modern business and culture. Some commodities and companies still struggled to outlive sluggish prices and other unstable market conditions or to modernize their businesses, but increases in productivity and profits were more common. A trend toward increased mechanical excavation in nonsoil materials was beginning to surface as a substitute for standard cyclic mine development techniques, such as drill-and-blast and surface shovel-and-truck routines. More continuous mechanical excavation offered the potential for increased production, fewer people at the working face, better ground control, and generally improved safety. The main limitation was rock hardness. The construction industry had already recognized the benefits of tunnel-boring machines for long underground drives and mechanical planers for pavement removal. The Colorado School of Mines held a short course during the year entitled, "Mechanical Excavation Techniques in Mine Development and Production,'" which was at-tended by nearly 100 engineers from 12 countries. The consensus of attendees was that for the most efficient use of these machines and techniques, new mining plans needed to be developed beyond the simple adaptation of those excavators to existing mine plans.1

Jan 1, 1991

By Allen D. Look

Underground fires often prove difficult to control , and a small fire can quickly grow into a large one , endangering life and causing large property damage . Even a small underground fire may produce enough noxious gases to cause suffocation ; therefore , every precaution should be taken to prevent and control such fires . It is ironic that mine fires should be caused when utilizing materials that are in themselves fire - resistant ; yet , cutting and welding of iron and steel are proving to be common causes of underground fires in metal mines . This paper includes 19 examples of underground fires of this nature , and undoubtedly this is only a fraction of the number of similar fires that have occurred in the last few years . This paper will review some metal - mine fires caused by cutting or welding and point out precautions to be taken to prevent other fires from this cause .

Apr 1, 1948

By J. G. Croeni

The high thermal-neutron cross section of gadolinium and the good mechanical and corrosion properties of titanium suggest that alloys of these two metals might be useful as control rod material. To aid in establishing the feasibility of this combination, the Federal Bureau of Mines investigated the titanium-gadolinium system. The results indicate that the system is composed of a single eutectic reaction and a peritectoid reaction involving the alpha-beta transformation of titanium. The eutectic isotherm extends from 1 to 99 pct, gadolinium at 1,240° C. The established eutectic composition is about 95 pct, gadolinium. The peritectoid reaction occurs at 885° C. and extends almost over the entire composition range. Hardness increases slightly with additions of gadolinium, and little change is obtained by heat treatment. Alloys containing less than 10 pct. gadolinium are amenable to extensive cold-working, but alloys having higher percentage of gadolinium content are only moderately cold-workable. All alloys can be hot-worked in iron sheathing at 750° C. Observation indicates that all compositions possess good machinability. Corrosion resistance to water at room temperature is apparently poor, especially in the gadolinium-rich alloys. INTRODUCTION A combination of the good mechanical and corrosion properties of titanium and the variety of thermal-neutron cross sections characteristic of the rare-earth metals suggests that alloys of these metals may be used for control rod materials. For this reason the Bureau of Mines proposed a study of the titanium-gadolinium alloy system, and the Atomic Energy Commission sponsored the investigation.

Jan 1, 1961

By R. S. Dean

The principle of explosive crushing depends upon the fact that an expandable substance contained within the pores of a solid body will disrupt such a body upon expansion. Such expansion may be obtained by the detonation of an explosive or by the sudden release of pressure of a superheated liquid. That this principle of disruption may be applied to minerals rests on the fact that cracks, cleavage planes, and pores exist in all minerals to an extent hardly conceived possible heretofore. Crushing by this method takes advantage of forces applied from within the mineral rather than from forces applied from without. The application of a force from within would appear to be more effective.

Jan 1, 1932

By J. E. Tress

The Bureau of Mines has developed a process to utilize waste heat from electric arc steelmaking furnace gases to preheat the ferrous material charged to the furnace. Four heat exchangers were designed, tested, and operated successfully on 1-ton electric arc furnaces. Briquets and pellets were charged continuously, both countercurrent to the hot furnace offgasses and at ambient temperatures. A comparison of the electrical energy consumed in each situation showed that preheating can lower energy requirements as much as 15.6 percent.

Jan 1, 1975

By Mary A. Barrett

The Bureau of Mines conducted a laboratory-scale investigation of grouting mixtures containing iron or aluminum to determine the existence of health or explosion hazards, due respectively to oxygen depletion or hydrogen emission. Mixtures containing iron created an oxygen deficiency in less than 24 hours and released small amounts of hydrogen; a health hazard could occur but only under extremely unfavorable conditions. Mixtures containing aluminum released little hydrogen and consumed little oxygen; however, if improper on-site mixing yielded high local metallic aluminum concentrations, enough hydrogen might be released to produce an explosive atmosphere in a confined space.

Jan 1, 1969

By D. H. Baker

THIS REPORT presents the technique and equipment used in determining the hardness of titanium sponge. Detailed descriptions are given of the methods used in preparing test samples for chemical analysis and hardness testing, the method of melting and surfacing test ingots, and the technique of reading Brinell-hardness impressions. The arc-melting furnace described, for which engineering drawings are included, will produce from 70 to 90 double-melted buttons each 8 hours of operation. Experimental data are also presented depicting the effect on hardness of the methods of surfacing specimens, temperature of test specimens, and the effect of time at test load. These data show that surfacing of the specimen involves no critical machining operations but that the test surface must be paralleled by a relatively flat surface for contact with the anvil of the Brinell tester. The heating of a specimen to 150° C. during surfacing does not materially affect the results if the ingot is cooled to room temperature before the hardness impressions are made. The optimum time at load appears to be approximately 30 seconds, but load times of as much as 1/ ½ minutes will not cause major errors.

Jan 1, 1959

By D. L. Nussear, W. E. Wallace, N. Clark, M. Gautaum, G. Hong-Guang

"Results of a research effort directed towards identifying and measuring the genotoxic properties of respirable particulate matter involved in mining exposures, especially those which may synergistically affect genotoxic hazard, are presented. Particulate matter emissions from a direct injection diesel engine have been sampled and assayed to determine the genotoxic potential as a function of engine operating conditions. Diesel exhaust from a caterpillar 3304 diesel engine, representative of the ones found in underground mines, rated 100 hp at 2200 rpm is diluted in a multi-tube mini-dilution tunnel and the particulate matter is collected on 70 mm fluorocarbon coated glass fiber filters as well as on S"" x 10"" hi-volume filters. A six mode steady state duty cycle was used to relate engine operating conditions to the genotoxic potential. Results to-date on diesel exhaust have indicated that use of a primary component of pulmonary surfactant as a medium for collecting and applying respirable particulate material to cells for mutagenicity testing offers a true representation of in-vivo delivery of such respired aerosols to pulmonary cells and the genetic material within. Protocols have been developed to sample and assay the diesel soot and diesel soot/mineral dust complexes which would not compromise the surf ace and physical properties of the particulate material. Evidence has been gathered to show that diesel soot expresses mutagenic potential as dispersions in DPL in the Ames tests as well as sister chromatid exchange activity in the animal lung fibroblast ·derived V79 cell line. The results are comparable to the standard solvent extraction procedure. INTRODUCTIONDiesel engines are primarily associated with transportation; however, they are also very common in the work place. Of particular concern is the use of diesel engines in mining operations. Currently there are 1,950 diesel machines working in underground coal mines throughout the country. These units are used in 151 mines encompassing nine different states (MSHA, 1991). It is believed the use of diesel powered equipment has contributed to higher productivity in these mines. However, the exhaust from diesel engines operated in underground mines has been a subject of concern during the past decade because of its suspected relationship with health aspects. The particulate matter generated by the diesel engine is of particular concern."

Mar 1, 1992

By C. C. Merrill

Studies were made to determine the amenability of yttrium to fused-salt electrorefining in a controlled atmosphere. Tests were conducted in a LiCl- YCl3 electrolyte system at 710° C. The major variables studied were the YCl3 content of the electrolyte, from l.7 to 13.4 mol percent, and the initial cathode current density, from 410 to 1,630 amperes per square foot. Vacuum distillation was employed to remove salt from the deposited metal. Metallic impurities, except for lithium, could be reduced to near or below their lower analytical limits, ranging from 10 ppm for Cu to 300 ppm for Ta; reduction of oxygen content, however, was accomplished only in metal produced from electrolytes with 5.4 mol percent YCl3 or less. Initial cathode current density had little effect on the purity of the product.

Jan 1, 1967

By W. E. Dennis

"INTRODUCTION The strategic importance of zinc warranted investigation of the Silver Eagle zinc prospect, which was first examined by an engineer 3/ of the Bureau of Mines in January 1943.From October 12, 1943, to March 16, 1944, the Bureau explored the deposit by trenching, core drilling, and sampling to establish the amount and grade of ore and to test for the presence of sulfide-ore minerals at depth.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director."

Oct 1, 1946

By A. B. Coates

During the last three years the use of ethylene glycol dinitrate4 (E.G.D.) as at low-freeze (L.F.) agent in place of nitropolyglycerin has become common in the manufacture of explosives of the dynamite type. The usual proportion of D. G. D. in the explosive "oil" is 25 per cent; the remainder, 75 per cant, is regular nitroglycerin. These proportions were probably selected as a continuation of the practice of 25 per cent nitropolyglycerin and 75 per cent regular nitroglycerin.

Jan 1, 1929

By H. F. Yancey

A relatively large proportion of the coal produced in the state or Washington, especially in the coking coal areas is of fine size; hence washing by means of coal-washing tables to reduce the ash content is commonly practiced. For this reason the program of research in coal washing conducted jointly by the U. S. Bureau of mines and the College of Mines, University of Washington, has given special attention to the mechanism of the separation of coal from its impurities as affected by the coal-washing table with the object of

Jan 1, 1931

By Bruce K. Cantrell, Stephen W. Stein, David Hassel, Harvey Patashnick

The Mine Safety and Health Administration. Department of Labor, requires coal mine operators to measure compliance with federal re¬spirable dust exposure standards periodically using approved gravi¬metric samplers. However, the gravimetric approach, with its inher¬ent delays, cannot provide dust concentration data quickly enough to allow on-site correction of inadequate dust control strategies or re¬moval of personnel from harmful environments. Furthermore, alleged tampering with dust samples collected to determine compliance with standards prompted the Secretary of Labor to appoint a special Respirable Dust Task Group to study options to improve monitoring and control of respirable coal mine dust. The Mine Safety and Health Administration's Task Group recommended that the U.S. Bureau of Mines develop a fixed-site monitor that would provide continuous information to the mine worker and mine operator regarding dust levels and the status of compliance with the applicable respirable dust standard. In response to the Mine Safety and Health Administration's request, the U.S. Bureau of Mines is investigating several sensor tech¬nologies for continuously monitoring respirable coal mine dust. One of these technologies is the Rupprecht and Patashnick Co. tapered element, oscillating microbalance. The bureau is in the process of investigating the suitability of using this sensor in the high humidity and vibration environment of underground coal mines. Laboratory tests have indicated that, with modification, the sensor can meet the humidity and vibration requirements for underground coal mine use. Currently, the bureau is developing