Search Documents

By K. Robert Dorman

This Bureau of Mines report describes laboratory and field experimentation in building mine ventilation stoppings, air-door frames, and fan bulkheads with a civil construction technique. Shotcrete is applied to a free-standing, three-dimensional wire-truss panel, which is easily cut and rapidly erected. In mines where shotcrete equipment is available, this technique should be faster and cheaper than conventional block-and-mortar or monolithic concrete construction.

Jan 1, 1980

By Joseph W. Martin

The Bureau of Mines investigated the backscattering of low-energy gamma rays as a method for rapidly determining the incombustible content of coal mine dust. In this method, 60-kev gamma rays from americium-24l penetrate the dust and are reflected by elements in the dust to a thin crystal scintillation detector. The number of backscattered gamma rays is proportional to the incombustible content. Tests of 40 dry, mine-dust samples containing 50 to 100 percent inert material show an average error of 2 percent. Calibration of the apparatus is necessary for each rock dust to account for variable composition. Results for samples containing more than 6 percent moisture are subject to error, but the values are lower than values obtained by chemical analysis, and thus fall on the safe side. Development of a small portable meter based on the backscatter principle appears feasible. Such a meter would find application within coal mines to check the effectiveness of rock dusting procedures.

Jan 1, 1968

By W. M. Weigel

"The use of sand for the filtration of municipal water supplies is comparatively recent use in this country, although at the present time, most cities of any size that draw their water supply from surface sources use sand filters in their purification system. Not only are sand filters employed to remove sediment and suspended matter, but they also take out most of the bacteria in the water.The first comprehensive research and study of sand for this purpose was probably that of Hazen for the Massachusetts Board of Health in 1891 and 1892, although sand filters had been employed for a considerable time before, specifications for filter sand drawn since then have been largely based on the results of Hazen's work,The general requirements for filter sand are more exacting than for any of the different kinds of sands, except the chemical specifications for glass sand. Filter sand must be uniform in size and within certain limiting sizes. In addition, it must be clean and free from clay and organic matter and of fairly high purity. Early investigations established the fact that an excess of fine materiel increased the friction and decreased the rate of flow through the filter, and that the size of the finer particles rather than the courser, determined the effective size. Also, that large grains tended to cause irregularities in flow in different parts of the bed. There is no requirement as to grain shapes, except that they be not flat or elongated, since, so far as known, either rounded or angular grains are equally efficient.Based on Hazen's investigations, two factors are quite generally used to control the average size and uniformity of size of the sand. These are defined as follows: The ""effective size"" of a sand is such that 10 per cent by weight of the seed is finer than this size, end 90 per cent is coarser. It is expressed in millimeters, The ""uniformity coefficient"" is defined as the ratio of the size of grain which has 60 per cent finer than this size to the size which has 10 per cent finer (the ""effective size""). It is evident that the smaller this coefficient, the more uniform is the seed. If all the grains were exactly the same size, the coefficient would be 1."

Jul 1, 1924

By W. H. Eddy

The Bureau of Mines conducted laboratory batch flotation tests and continuous pilot plant flotation tests on a complex calcareous fluorspar ore from Cave-in-Rock, Ill., to determine the technical feasibility of producing commercial-grade concentrates by the sodium fluoride-calcium lignin sulfonate-fatty acid method of concentrating fluorspar previously developed by the Bureau. The continuous flotation tests, treating about 150 pounds of ore per hour, produced fluorspar concentrates assaying 96.4 percent CaF2; 90 percent of the fluorspar was recovered.

Jan 1, 1967

By J. J. Forbes

The investigation of major and minor coal-mine disasters has been a routine function of the Bureau of Mines since its inception in 1910, and the facts obtained during such investigations have been used as a basis for determining the precautions that the personnel of many mines are observing to prevent similar occurrences, The Bureau has conducted extensive research on roof-control problems, but a comprehensive study of fatal roof-fall accidents was not attempted until February 10, 1950, when the policy of investigating all coal-mine fatalities was approved by Bureau of Mines Director James Boyd. The investigations are being conducted by Federal coal-mine inspectors functioning under the provisions of the Coal Mine Inspection and Investigation Act of May 1941, Public Law 49, and reports covering the investigations are distributed to management, the State mine inspection agency, and representatives of the mine workers organization having jurisdiction at the mine. SCOPE AND PURPOSE OF STUDY This study covers the Federal investigation of 263 of the 315 fatalities from falls of roof, face, or rib that were charged to the bituminous-coal industry during the calender year 1950. The number of roof-fall fatalities investigated is recorded by States in table 1.

Jan 1, 1951

By E. S. Leaver

The mineral value in the ores from the Mother Lode mining districts of California is almost entirely gold, Although many mines have produced extremely high-grade ore the usual mill grade averages approximately $7.00 gold per ton. Fully 80 per cent of the gold has been and is now being recovered by amalgamation. Various methods have been introduced to recover the gold that was not obtained by the amalgamation processes. They include vari¬ous kinds of gravity concentration which in some cases were followed by chlorination or cyanidation. The usual practice includes only stamp battery, plate-amalgamation, and vanner concentration. In the very early practice the tails were run to waste through the main drainage streams of the different mining districts. During later years very large storage dumps have been impounded. These old tails, together with those being saved from present mills, furnish the problem discussed in this article. The clean sand portion of these mill tails is amenable to the usual cyanidation. The slime portion contains the major amount of the gold lost, but it also contains 1-1/2 to 3 per cent carbon, which precludes direct cyanidation of this part of these low-grade waste tails. The black carbonaceous slime portion is the particular problem considered in this report.

Jan 1, 1930

By V. B. Dale

This paper is one of a Federal Bureau of Mines series covering the mineral resources of the Nation. It briefly describes most of the tungsten deposits in Cochise, Pima, and Santa Cruz Counties, Ariz. Most of the descriptions are from field examinations by the two senior writers, prior to July 1957. Wolframite first was identified in Arizona in 1896 by W. P. Blake, Territorial Geologist. Tungsten mining began about 1900 in the Little Dragoon deposits of Cochise County, and about 1901 in Las Guijas district of Pima County. The price history of tungsten is an erratic one; consequently, production has been erratic. Prices rise during wars and periods of national preparedness. Production of tungsten ore was stimulated greatly by a Government purchasing program, announced on May 10, 1951, wherein the Government agreed to purchase standard-grade tungsten concentrates at $63 per short ton unit5/ for 5 years or until 1,468,750 units were purchased. This was later increased to 3,000,000 units, and after this amount had been purchased in June 1956, the purchase of an additional 1,500,000 units was authorized. Government purchase, however, was suspended in December 1956 before completion of this latter program, and the price of tungsten concentrates declined sharply. The price had dropped to $15 per short ton unit, duty extra,6/ by the last part of July 1957.

Jan 1, 1960

By Doris M. Hyde

To a greater or lesser extent, the economies of the smaller Caribbean Island countries continued to have common problems. These included unemployment, inflation, foreign exchange shortages, trade deficits, and unstable world prices for their exports. Declining prices for petroleum provided some relief from scarce foreign exchange. Overall, the mineral sector remained stable. The Amerada Hess Corp. crude oil transshipment terminal on St. Lucia was completed during 1981. However, there were no shipments during the year. No official reason was offered for the delay in opening the terminal, but it may have been related to the world surplus of crude oil that occurred in 1981. There has been no further action on the refinery, which was to complete the island's petroleum complex. During the first half of 1981, an announcement was made that a second oil transshipment terminal would be built on St. Lucia. The report indicated that the terminal was to be financed by Saudi Arabia and include underground storage. After the original announcement, no further information was made available. This terminal, like the Hess petroleum complex, may have been temporarily postponed because of the crude oil surplus.

Jan 1, 1983

By Mark R. Stephenson

Everyone knows that mining is a noisy job, but did you know that you are nine times more likely to lose your hearing than someone who works in a quieter job? If unprotected from noise on the job, by age 50, you will probably need hearing aids. Obviously, the best solution is to engineer out the noise, but that isn?t always im­mediately possible. Until mines are quieter, one way you can help save your vital sense of hearing is to use hearing protectors whenever the noise around you is hazardous. Even if you already have some hearing loss, you can use hearing protectors to prevent your hearing from getting worse. When loud noise is present, proper use of hearing protectors will help miners pre-vent most or all noise-induced hearing loss.

Jan 1, 1998

By B. W. Madsen

A nearly dormant copper sulfide pilot-scale experimental leach containing 8.7 tons of are was injected with oxygen to determine its effect on the copper-leaching rate. Prior treatment of the uncrushed 0.25-percent-copper, mine-run stripping material consisted of 461 days of acid ferric sulfate leaching, which extracted 47 percent of the total copper. The permeability of the bed had decreased, and the percolation rate had decreased from an initial 20 gallons to 0.8 gallon per square foot per day. Copper extraction had nearly stopped. After injecting oxygen into the ore column and leaching for 30 days, the percolation rate was increased to 6 gallons per square foot per day. In an additional 298 days of leaching, an additional 40.7 percent of the copper was extracted. The improved leaching after the use of oxygen is attributed to stimulated bacterial action, better oxidation, and increased permeability.

Jan 1, 1975

By John T. Kuo

The miner's seismic source strength can be approximately estimated on the basis of a single force acting in an infinite medium. Because of the uncertain- ty involved in estimating the amount of conversion from mechanical energy to seismic energy, the source strength thus estimated may be in error by as much as a half-order of magnitude. Calculations of wave transmission must take into account geometrical spreading, dissipation of energy by internal friction, and energy partition due to reflection and refraction of waves impinging on inter- faces in the layered earth. Theoretically derived peak-to-peak particle velocities in microinches per second (PIPS) are given for two models ; viz: (i) 50-feet thick and (ii) 100- feet thick 4000 ft/sec layers with Q = 20, overlying a half-space of 10,000 ft/sec material with Q = 5O;for the cases .of a hammer blow and a timber impact, at the frequencies of 50 Hz and 100 Hz. Comparison of the theoretically derived peak-to-peak particle velocity with experimental data taken at the Copper Queen Mine indicates that the theoretical particle velocity may be overestimated. A discussion of the distortion of seismic wavefronts by mine tunnels indicates that it is unfavorable to use a seismic source impact on the floor of the tunnel, since deceptive delays in arrival time are liable to occur at the surface. A program of parallel theoretical and experimental work is required to clarify uncertainties still associated with the nature and strength of the miner's seismic source signal which cannot be resolved within the approximations of this work. Its major components include theoretical investigations of the (1) Wave diffraction and scattering of an impact source on a face of a cylindrical cavity. (2) Impact of an elastic object on an elastic medium.

Jan 1, 1974

By Edward L. McHugh, Charles Sabine, Louis J. Denes, Jami M. Girard, Peter Metes

The Spokane Research Laboratory, National Institute for Occupational Safety and Health, is investigating various remote sensing technologies as possible tools to detect, monitor, and mitigate hazardous situations in surface mines that could lead to catastrophic slope failure. Promising technologies include a field-portable spectro-polarimetric imager and a stationary interferometric radar device. Field tests were conducted of a prototype visible and near-infrared spectro-polarimetric imager (SPI) built at the Carnegie Mellon Research Institute. The SPI employs anacousto-optical tunable filter (AOTF) to control wavelength, a phase retarder to measure polarization signatures, and a digital camera and computer to capture data. Images obtained at the Mountain Pass and Castle Mountain mines in southeastern California showed that the instrument is capable of obtaining hyperspectral images of highwalls, outcrops, hand samples and drill core in the field. We have retrieved spectra from Mountain Pass images that closely match those of bastnaesite and have had some success in classifying images. Although radio frequency noise in the data limited spectral classification of imagery, we project that careful alignment of the AOTF should minimize the noise and greatly improve classification.

By Rees D. Groves

The Bureau of Mines conducted research on reactions of copper sulfide minerals with chlorine in an aqueous system. Selected samples of covellite, chalcopyrite, chalcocite, bornite, and pyrite were leached with aqueous chlorine solutions. The mineral samples were sized on to minus 100- plus 325-mesh, individually mixed with precleaned sand and leached in an enclosed percolation column. Each mineral was leached in stages to achieve about 90 percent mineral dissolution. The chlorine leaching solutions were produced by reacting sodium hypochlorite with hydrochloric acid within the closed system. The study showed that when the mineral dissolution was complete, the reaction products (copper, iron, and sulfur) were in their highest oxidation states and a stoichiometric amount of chlorine was consumed. Although elemental sulfur formed as an intermediate product, it was oxidized to sulfate during the leach.

Jan 1, 1973

By J. J. McClelland

The face area of a continuous mining section of an underground coal mine is the most dangerous area in the mine. Workers there are at nearly twice the risk of death or disabling injury than those in other parts of the mine. Despite extensive training of miners and improved equipment and mining methods, fatality and injury rates have remained constant during the past few years. It is clear that advanced research is necessary to apply new technologies or modify work procedures to solve the continuing problem of the loss of lives and the numerous injuries at the mine face. A U.S. Bureau of Mines research program is developing a Reduced-Exposure Mining System (REMS) that relocates personnel operating the mining machinery at the face away from the hazards to a nearby haven of relative safety. REMS uses proven technologies of computer automation and robotics to help control the operation of the mining machines at the face, while personnel are moved away to a nearby, safe control room. In this protected, well-ventilated environment, they can supervise or control the operation of the machines while viewing what the machine is doing using video and graphic display monitors.

Jan 1, 1994

By R. R. Backer

The Bureau of Mines investigated the typical physical and chemical properties of coal waste materials from the western part of the United States. The results are compared, in so far as possible, with the properties of waste materials from eastern coal operations. The authors found a disparity of mines and preparation plants among western U.S. coal operations and dissimilarities with typical operations in the East. The relatively cleaner product from the predominance of surface mining and the occurrence of thicker seams in the West reduces the amount of coal preparation required and the size of the waste piles. Because of the abundance of land available for waste disposal, many of the piles are low and extended over large areas. New concepts relating statistical shear strength data to liquifaction potential are presented. The somewhat limited data indicates that western coal sludge is coarser with higher permeabilities and shear strengths than the eastern deposits.

Jan 1, 1977

By G. S. Rice

The recommendations of the Bureau of Mines on rock dusting practices are embodied, except in a few details, in the Recommended American Practice for Rock-Dusting Coal Mines to Prevent Coal-Dust Explosions, approved by the American Engineering Standards Committee. December 30, 1925. It is specified that the dust to be used is of a elm that all will pass through a sieve having 20 meshes per linear inch and that 50 per cent or more will pass through a sieve having 200 meshes per linear inch. Thus the coarsest size of dust and the minimum proportion of fine dust are specified, but the specification does not indicate whether a larger proportion of fine dust would be desirable. There have been advocates of the use of that size of rock dust of which the particles would all approach 200-mesh in fineness. Explosion tests were made in the Experimental mine in the earlier period of testing which indicated that the finer rock dust is somewhat more effective under test conditions, but not sufficiently so to Justify the cost of finer grinding of the dust; also there are some disadvantages of finer dust described hereafter.

Jan 1, 1930

By D. A. Reynolds

The Bureau of Mines-American Gas Association survey of the carbonizing properties of American coals was begun in 1929, and has been continued almost without interruption since that time. Upwards of 100 coals have been carbonized at low, medium, and high temperatures in this survey, and about 200 additional coals have been carbonized at high temperatures only. All survey coals were blended with coal of different rank for carbonization at one high temperature (900° C,). During the past few years, 12-high-volatile A coals were blended with Pocahontas No 3 coal from Kimball, McDowell County, W. Va., and in this report the physical properties of the cokes from these high-volatile coals and their blends are compared.

Jan 1, 1949

By W. H. Young, R. L. Anderson

"Physical conditions, such as thickness and character of the coal seam, dip or pitch of the seam, depth of cover, character of roof and overlying strata, mine water, etc., affect the productivity in bituminous-coal mining. Thickness of the coal seam being mined is probably the most important single item that determines whether the output per man per day shall be low or high; however, in strip mining the depth of cover or overburden to be moved is of equal importance.Bituminous coal is mined today from seams of exceedingly variable thickness - less than 2 feet to more than 50 feet; however, a large majority of the mines are producing .coal from seams 3 to 6 feet thick. The average thickness of the coal seams mined in the United States has not changed materially in the past 25 years. The average seam thickness for all bituminous-coal mines was 63 inches in 1920 4/ and 65 inches in 19)45. As thick seams have been exhausted in the older fields, other thick seams, have been opened in the newer fields.Productivity increased from 4 net tons per man per day in 1920 to 5.78 in 1945. This 45 percent increase in productivity resulted from increased mechanization. The percentage of underground production represented by coal cut by machines increased from 61 in 1920 to 91 in 1945 Mechanical loading increased from less than 1 percent of underground production in 1920 to 56 percent in 1945, and strip mining increased from less than 2 percent to 19 percent of the total production during the same period."

Dec 1, 1947

By B. J. Scheiner

The Federal Bureau of Mines has successfully demonstrated an electrooxidation-solvent extraction-carbon adsorption process for recovering molybdenum and rhenium from offgrade concentrates. The flow sequence consists of dissolution of metal values by electrooxidation, liquid-solid separation by thickening, acidification and chlorate ion removal by sulfur dioxide treatment, solvent extraction to concentrate the molybdenum and rhenium, separation of molybdenum and rhenium by carbon adsorption, and metal recovery by crystallization. Molybdenum and rhenium were recovered as ammonium paramolybdate and ammonium perrhenate. Electrolysis of brine-concentrate pulps to generate a hypochlorite oxidizing agent in situ resulted in the dissolution of 98.9 and 99.1 pct of the molybdenum and rhenium, respectively, at an energy consumption of 13.7 kwhr/lb of molybdenum extracted.

Jan 1, 1976

By Donald H. Mullen, Walter R. Storms

"INTRODUCTION The Copper Flat area of the Central mining district, Grant County, N. Mex., has been visited by numerous engineers 4/ of the Bureau of Mines and geologists 5/ of the Federal Geological Survey. In December 1944 the Bureau. 6/ proposed that geophysical work be done in that area in order to locate favorable sites for future company exploratory and development work. This geo-physical work was begun early in 1945 but never fully completed because of insufficient funds. The engineers who made the survey recommended that more work be done, especially to locate the bottom of the Copper Flat laccolith by resistivity-depth surveys. All known minable zinc-lead ore bodies had been found above this laccolith in the Copper Flat mine, but it was thought that other minable ore deposits should occur in favorable limestones beneath it. The geophysicists also recommended core drilling beneath the laccolith.In the summer of 1946, following some mapping by S. G. Lasky of the Federal Geological Survey, funds were appropriated for a Bureau of Mines project in the Copper Flat area. The project was completed in June 1947. 8/"

Apr 1, 1948