Search Documents

By A. R. Taylor

Using solution calorimetry, the following heats of reaction were determined: (1) NaCN(c) + 1/Cu20(c) + 129H20(l) ? CuCN(c) + NaOH?128.5H2O ?H = -13.44±0.10 kcal/mole, (2) HCN(2) + NaOH?128.5H20 ? NaCN(c) + 129.5H20(l) ? = -2.52±0.02 kcal/mole. From these reactions, the heats of formation for CuCN(c) and HCN(2) were calculated to be 22.7±0.4 kcal/mole and 24.9±0.4 kcal/mole, respectively. Reaction 2 was made to check the consistency of literature values for heats of formation of HCN and NaCN. Adiabatic calorimetric measurements between 10° and 400° K showed the entropy and heat capacity of CuCN(c) to be 21.51±0.06 eu and 14.58±0.04 cal/mole deg, respectively, at 298° K. A broad anomaly in the heat capacity was found in the temperature range 285°-320° K. The heat of transition associated with this anomaly was less than 1 cal/mole, the sensitivity of the measurements.

Jan 1, 1971

By John A. Breslin

Size distributions and concentrations of particulates emitted from diesel engine exhausts were measured with cascade impactors. Samples were taken from the exhaust of two types of engines using three types of fuel and operating under five different engine speed and load conditions. The measured mass median diameters of the diesel particulates were typically about 0.3 um. There was no significant difference in mass median diameter between engines or fuels and only a slight dependence on operating mode. Concentration measurements ranged from 14.2 to 250.9 mg/cu m, and calculated mass outputs, from 64 to 10,000 mg/min. Significant differences in mass output were found between engines, fuels, and especially between different operating modes. The quantity of clean dilution air that would be required to reduce the particulate mass concentration below the 2.0 mg/cu m respirable dust standard for coal mines was greater than the dilution air required to meet the standards for noxious gases for both engines tested.

Jan 1, 1976

By T. J. Ballard

The Union Copper mine is in the Gold Hill district; Rowan and Cabarrus Counties, N. C. The mine was discovered in 1799 and first worked as a gold mine; but copper was encountered at depth, and the property became an important producer of copper. It is estimated that the mine produced 5,000,000 pounds of copper before operations were discontinued in 1907. As part of the strategic minerals program, the Bureau of Mines conducted a development project on the property from July 1943 to November 1943. Eight diamond-drill holes totaling 2,500 linear feet were drilled to delineate the ore body. Analyses 205 core samples were made. Tabulations of sample analyses and drill-hole logs are presented in this report.

Jan 1, 1948

By J. R. Hauger, P. A. Romans, W. J. Niebuhr

With suitable instrumentation and techniques it is possible to determine the presence of tantalum in columbium to 20 ppm . This paper discusses the selection of X- ray spectrographic instrumentation and describes a technique for accomplishing the low level determination of tantalum . An ion- exchange method of separating tantalum from columbium is also described .

Jan 1, 1964

By J. J. Drost

The feasibility of basic oxygen furnace (BOF) offgas heat recuperation by preheating scrap was investigated on a pilot plant scale by the Bureau of Mines. In this study, offgases generated during the oxygen blowing of a molten pig iron and scrap charge were passed through a static bed of shredded auto scrap. Scrap quantities varying from 100 to 180 pounds and representing from 22 to 40 percent of the 450-pound BOF metallic charge were preheated in this manner. Average scrap bed temperatures of 1,650° F for 100 pounds of scrap and 1,150° F for 180 pounds of scrap have been achieved during the blows. As compared to cold scrap used in the normal BOF practice, it was found that by preheating scrap, usage could be increased by 43 percent. The thermal energy recovered by this preheating method can account for up to 44 percent of the energy necessary to melt the scrap.

Jan 1, 1974

By W. R. Huff

This report describes the development and operation by the Bureau of Mines of a pilot plant designed for using high-volatile A bituminous coal-in-water suspensions as a source of preheated coal and superheated steam in the pressure gasification of coal with oxygen. Figure 1 on page 2 is a block diagram of the integrated gasification process, in which a total of 70 tons of coal was fed from slurry and gasified. The present work included (1) development of equipment and methods both for mixing pulverized coal and water to produce slurry and for pumping and metering the slurry at gasification pressure; (2) development of equipment for heating the flowing slurry and, because slurry that can be pumped produces more steam than is necessary as a gasification reactant, developing equipment for removing and metering the excess steam; and (3) demonstration of the process under actual gasifier operating conditions, at a coal rate of about 800 pounds per hour and gasification pressures in the range 100 to 300 pounds per square inch gage. By using the forced-convection principle, a flow of slurry made from a caking, high-volatile A bituminous coal can be continuously heated to 600° F. in a coil-type heater. The flow rate and concentration of the slurry and the temperature gradient along the length of the heating coil must be closely controlled. In a radiant-type heater, involuntary reductions in flow rate, even momentary, can lead to coking and plugging of the heater coil.

Jan 1, 1961

By D. A. Lucero, J. E. Brockmann, L. A. Mondy, K. L. Rubow, D. J. Rader

"Department of Mechanical Engineering, University of Minnesota, Minneapolis, MNExperimental and correlated stage responses (the fraction of particles entering an impactor that are collected on a stage) are presented for the Andersen Mark III and Marple personal cascade impactors. The impactors were operated upright and fully assembled so that interstage interference and wall losses could be properly studied. The observed stage responses showed maxima that fell significantly short of unity, meaning that a monodisperse aerosol is never collected exclusuvely on one stage, but is distributed among several stages and internal losses. Correlations for the stage responses are presented so that the experimental results can be used to determine size distributions with available data-inversion algorithms. Simulations with log-normal distributions show significant differences between dpa50 histograms and the more accurate distributions that result by taking the response functions into account.Cascade impactors are widely used for the measurement of aerosol size distributions; their ruggedness and simplicity of operation make them an attractive choice for a variety of environments. In one common application, the aerosol of interest is drawn through the impactor, and the amount deposited on each stage is determined gravimetrically. The primary objective is to extract as much information as possible about the initial size distribution from the resulting set of weights. Unfortunately, the reconstruction of contin-uous size distributions from finite data sets is an ill-posed problem. Not surprisingly, a variety of such reconstruction techniques are presently in use; the success of each method depends on the particular nature of the aerosol sample and the instrument response.Inversion of impactor data by any of these techniques requires that the response functions for each stage be known. The stage response function gives the fraction of particles entering the impactor that deposits on that stage. Values of the response function range from zero to one, and depend on impactor operating conditions (e.g., geometry, flow rate, and gas properties) and particle properties (e.g., diameter, density, and shape factor). As interstage interferences and particle losses will affect each stage's response, experimental determination of stage responses should be made for fully assembled impactors. Unfortunately, impactor stage response functions are rarely reported; rather, single-stage efficiency curves are given that provide an incomplete description of impactor performance.This paper presents experimental stage responses for two fully assembled cascade impactors: the Andersen Mark III and Marple personal impactors (model 298, Andersen Samplers, Inc., Atlanta, Ga.). These calibrations were performed with monodisperse liquid droplets for both impactors and also with monodisperse solid spheres for the Marple personal impactor. The calibration results for the Mark 111 impactor presented here have been previously reported in the response-function format (Rader et al., 1989). The calibration results for the Marple personal impactor, however, were originally presented in the single-stage efficiency for¬mat (Rubow et al., 1987) and have been reanalyzed in this work. Losses within both impactors are considered, and their treat¬ment within data inversion techniques is dis¬cussed. In addition, correlations for each impactor's response functions are presented so that these calibration results can be easily included in data-inversion algorithms. Size distribution inversions using these response correlations are compared with the standard cut-point method for two lognormal test dis¬tributions."

Mar 1, 1992

By Daniel R. Babich, Jeffrey R. Vipperman, Eric R. Bauer

Prolonged exposure to loud noise can cause permanent damage to the auditory nerve and/or its sensory components. Despite regulations and efforts by government and industry to reduce noise-induced hearing loss (NIHL), it is still a problem in the U.S. coal mining industry. The Mine Safety and Health Administration noise standard (30 CFR3 62), which was enacted in September 2000, is aimed at reducing NIHL in the mining industry. To address NIHL in various aspects of coal mining and provide the necessary information to effectively implement control technologies, the National Institute for Occupational Safety and Health conducted a cross-sectional survey of noise sources and worker noise exposures. Noise surveys consisting of full-shift worker noise exposure (dose) determination, time-motion studies (task observations), and equipment and/or area noise profiling were completed in 8 underground coal mines, 10 surface coal mines, and 8 coal preparation plants. The studies revealed that more than 40% of all workers monitored were subject to noise exposures above 90 dBA TWA8. A summary of these studies is presented, their application to administrative and engineering controls is discussed, and exposure reduction methods are reviewed.

Jan 12, 2006

By Paul T. Allsman

This paper gives the cost and describes the mining of 55 tons of nickel-bearing rock by hand methods from a prospect in southern Nevada, June 15, 1937, by the Mining Division of the Bureau of Mines. The geology, mineralogy, and problems related to future development also are discussed briefly. The main object was to obtain a 55-ton sample within the limited period during which funds were available; little time was available to make a first-hand detailed study of the possibility of commercial ore deposits being found. The sample was desired by the Metallurgical Division of the Bureau for experimental purposes at the Electro-Metallurgical Station at Boulder City, Nev. The term "ore" is used loosely in the following discussion to designate dike material containing nickel and copper, without consideration of its commercial value. ACKNOLEDGMENTS Material concerning the geology and mineralogy of the prospect and district as obtained from Geological Survey publications by Bancroft3/and Longwell4/.

Jan 1, 1938

By P. T. Brooks

This Bureau of Mines study describes a process for recovering nickel, cobalt, molybdenum, and chromium contained in complex waste superalloy grindings that, for lack of an economical domestic recovery process, are being largely marketed abroad. The process, devised by laboratory scale operations, includes scrap preparation, dissolution of metallics in hot chlorinated acidic liquor, carbon adsorption, three successive solvent extraction separations, and selective chemical precipitations. Nearly 90 percent of the nickel, cobalt, molybdenum, and chromium were separated and recovered as oxides, carbonates, and basic sulfate products.

Jan 1, 1969

By Charles Vaught, Warren G. Lacefield, Ronald D. Wasielewski, Philip K. Berger, Henry P. Cole, John V. Haley, Shannon L. Price

A comprehensive review of published research was carried out to identify methods for teaching and assessing critical but nonroutine skills needed for coping with emergency situations. Computerized searches of the relevant data bases were carried out, along with identification of relevant articles and materials by personal contact with experts in many fields. The citations listed in this bibliography resulted from this systematic literature search and review. The computer searches and an analysis of this literature are described in technical report 1. Specific methods for assessing critical skills proficiency in aviation, medicine, organization management, the military, and other industrial/ technical workplaces were described. The potential application of these methods for teaching and assessing (1) critical first aid and (2) self-rescue and escape skills to underground coal miners in annual refresher training was explored. Research and development activities that may improve mine health and safety training were suggested. Most of the entries in this bibliography were assembled in 1984 through 1985. Study of these materials contributed to the completion of the project research that followed. This later work is reported in the project technical report 2 and the final report. This bibliography is most useful when combined with examination of technical reports 1 and 2 and the final project report.

Jan 7, 1988

By Natalie A. Sapola, Knox Van Dyke, Jean Rabovsky, Vincent Castranova, William H. Pailes, Melanie McPeek, Deloris J. Judy

"INTRODCJCTJONPlatelet activating factor (PAF) is a glycerophospholipid (1-0-alkyl-2-acctyl-sn-glycerol-3-phosphoryl choline) which has been shown to mediate a broad range of biological activities. 1·3 Its pulmonary actions include contraction of pulmonary tissue,4 secretion of leukotrienes from leukocytcs,5 airway constriction,6 pulmonary edema,7 and enhanced migration of neutrophils into the airspaces of thelungs.8-9PAF can be released from several different cell types, such as, basophils, neutrophils and alveolar macrophages, in response to a variety of particulates or membrane stimulants which include zymosan, calcium ionophore, phorbol esters, chemotactic agents, and endotoxin. 1~1 3 Therefore, PAF may play an important role in the development of pneumoconioses by mediating pulmonary responses of lung cells to a variety of occupational dusts. To investigate this possibility, we determined the effects of P AF on several physiological parameters of neutrophils, alveolar macrophages, and alveolar type Il epithelial cells.METHODSIsolation of CellsNeutrophils were isolated from human blood by dextran settling and centrifugal elutriation.14 Isolated neutrophils (93% pure) were resuspended in HEPES-buffered medium (145 mM NaCl, 5 mM KCI, 10 mM HEPES, 5 mM glucose, and 1 mM CaC12; pH = 7.4). Cell number and volume were determined with an electronic cell counter equipped with a sizing attachment.Rat alveolar macrophages were obtained by pulmonary lavage with ea2+, Mg2+-free Hanks balanced salts solution. 15 Alveolar macrophages (94% pure) were resuspended in HEPES-buffered medium, counted, and sized electronically.Rat alveolar type Il cells were isolated by enzymatic digestion for 35 minutes at 37°C with 40 µ/ml type I elastasc and 0.1 % collagenase and purified by centrifugal elutriation. 16.17 Type Il cells (92 % pure) were resuspended in HEPES-buffered medium for measurement of membrane potential, oxygen consumption, and trypan blue exclusion. Type Il pneumocytcs were resuspended in 0.1 M NaCl plus 0.05 M HEPES (pH = 7.8) to measure cytochrome P450-dependent activities and aggregation. Cell size and number were determined electronically."

Jan 1, 1990

By G. L. Hundley

An anhydrous chlorination process has been developed by the Bureau of Mines for the production of copper, ferric oxide, and sulfur from chalcopyrite. The first part of the process is a chlorination step in which elemental sulfur and a mixture of iron-copper chlorides are produced. This paper describes the second step of the process in which the copper and iron chlorides are reacted with oxygen to selectively convert the iron chloride to ferric oxide and chlorine leaving the copper in the chloride form. The chlorides are pulverized and dropped countercurrent to a flow of oxygen in a vertical 20-cm-diam. reactor at 800° C. By leaching with brine, the copper chloride may be separated from the insoluble iron oxide and reduced to copper powder by electrowinning. It has been demonstrated that 70 to 80 pct of the iron can be converted to oxide in a single-stage operation with a chlorine content in the offgas of 80 pct. After removal of the oxygen, this chlorine could be recycled to the chlorination step. A two-stage operation will convert 98 to 99 pct of the iron in the mixture to insoluble oxides. The offgas from the second stage contains 70 pct chlorine.

Jan 1, 1974

By Philip G. Freeman

The growth-promoting properties of coal-derived humus were tested by a variety of bioassay methods. Humate materials used included leonardite, a form of naturally oxidized lignite, and humic acids extracted from leonardite. It was found that the greatest effects were evident when water-soluble humic acid was applied to excised root tips. No significant short-term effect was noted when water-soluble humic acid was applied to stem or coleoptile sections. Root initiation was promoted in bean stems when high concentrations of coal-derived humate were applied. Gross weight of tomato plants was increased by up to 40 percent when coal-derived humates were added in concentrations of 101 to 104 ppm to the nutrient in a hydroponic growth test of 6 weeks' duration. It is concluded that coal-derived humate promotes the uptake of minerals, specifically iron, by serving as a metal chelate.

Jan 1, 1968

By C. R. Stephan, N. B. Greninger, S. J. Luzik

The U.S. Bureau of Mines conducted explosion tests on various full-scale cementitious bulkheads used in abandoned mine areas to evaluate the ability of the bulkheads to withstand gas explosion over-pressures of 20 psig. Tests were performed on 120-ft2 solid-concrete-block seals of varying thicknesses and designs. Of the seven solid-concrete-block seals tested, only the standard-type seal, having a 16-in thickness, keyed at the floor and ribs, all joints mortared, wedged at the roof, and a center pilaster, maintained its integrity when subjected to a 20-psig pressure wave. After being subjected to repeated explosions, the standard seal only showed a small hairline crack and had an air leakage of 87 ft3/min at a pressure differential of 1 in H2O. Tests were performed on cementitious foam seals of varying thicknesses and compressive strengths. Explosion tests have shown that 200-psi strength, 4- and 8-ft-thick seals can withstand a 20-psig pressure wave. At a pressure differential of 1 in H20, no air leakage was detected through the 200-psi, 8-ft-thick foam seal.

Jan 1, 1991

By Howard D. Jacobs

A bulk sample of oxidized taconite taken from the western Mesabi Range was evaluated by the Bureau of Mines using the Bureau-developed selective flocculation-desliming-cationic (or anionic) flotation process. The raw ore sample containing 32.3 pct Fe was treated by both cationic and anionic flotation. Using the cationic system the concentrates averaged. 37.2 wt-pct of the feed and contained 62.8 pct Fe and 4.7 pet Si02 with an iron recovery of 72.3 pet. With the anionic system, concentrates averaged 37.7 wt-pet of the feed and contained 63.0 pct Fe and 5.3 pct 8i02 with an iron recovery of 73.5 pct. A comparison of reagent costs showed that the cationic process cost 144.1 cents per long ton of crude ore and the anionic process 178.7 cents per long ton of crude ore. Reclaimed water comprised 86 pct of the total water requirement for anionic flotation and 88 pct for cationic flotation. The ore used in this study was one of three samples representing about 3.25 billion tons of oxidized taconite containing from 32 to 36 pct feed iron. Previous study had indicated that selective flocculation-desliming-cationic flotation would produce concentrates from the other two samples of 61.7 pct Fe and 5.1 pct Si02 at 67-pct Fe recovery, and 63.5 pct Fe and 4.3 pet Si02 at 8S-pct Fe recovery. By developing a successful treatment for these ores, the Bureau has insured the availability of technology for processing an amount of raw iron ore which, by itself, would supply U.S iron needs for 50 to 75 years at expected consumption rates.

Jan 1, 1981

Aid mine operators as well as mine inspectors in making quick but sufficiently accurate measurements of the rock dust content of coal/rock dust mixtures. The Problem Past research has shown that accumulations of volatile coal dust in underground coal mines can be rendered non-explosive by dilution with chemically inert rock dust (usually limestone). Consequently, rock dusting is required by law in U.S. underground coal mines. However, mine officials and inspectors have no quick and reliable means to determine whether enough rock dust has been applied to achieve a mixture that is in compliance with the law. Even the compliance tests used by the Mine Safety and Health Administration (MSHA) are slow and involved. MSHA assures that a mine has been rock dusted adequately by collecting samples from rock dusted areas of the mine and sending the samples to a laboratory for analyses of the inert-dust content. The analyses may not be completed for more than two weeks, during which time the mine in question might be inadequately protected against coal dust explosions. To solve this problem, the Bureau of Mines devised a quick, simple and reliable device that can immediately determine the rock-dust content of a mixture of coal and rock dust.

Jan 1, 1985

By Radford Schantz

In 1990, the Bureau of Mines (BOM) conducted a mineral investigation of the mines and prospects in the East Mojave National Scenic Area (EMNSA). San Bernardino County. California During field work. BOM identified 701 mines and prospects in EMNSA for which the geology, mineral resources, and mining history were compiled and summarized. Analytical results for 1.188 rock samples collected are tabulated. Total value of identified resources in EMNSA is $5.0 billion. Twenty-four mines and prospects were deemed profitable under current economic conditions. Development could generate considerable economic benefits to San Bernardino County. Potential economic benefits from mining the deposits were evaluated under the following access restrictions for EMNSA: 1) fun access, 2) HR 3460, and 3) S 11/HR 780. Under the full access scenario, cumulative mine revenues are $3.0 billion, cumulative personal earnings at mines and supporting industries are $0.94 billion, and annual jobs at mines and supporting industries are 2,379. Under HR 3460, mine revenues, personal earnings, and annual jobs are $2.9 billion. $0.88 billion, and 2,165, respectively. Under S 11/HR 780, mine revenues, personal earnings, and annual jobs are $1.0 billion, $0.32 billion, and 936, respectively.

Jan 1, 1990

By R. W. Huber

The successful development of a titanium prototype of the 81-mm. mortar base plate for the Army Ordnance Corps is outlined in this report. Information is presented dealing with forming, forging, and machining, welding and assembly techniques, and design changes relative to this prototype. INTRODUCTION The work of the Federal Bureau of Mines in making ductile titanium available2/ has resulted in the establishment of a new industry. Owing to its strategic importance and the combination of low density and high strength, titanium has received considerable attention as a structural metal. Titanium's favorable strength-to-weight ratio is of particular importance to the Army Ordnance for equipment that is transported by airplane or by foot soldiers.

Jan 1, 1956

By E. C. Baker

The Bureau of Mines estimated the economic feasibility of investing in a directional hole methane drainage project in the Pittsburgh coalbed for 5 yr in advance of mining. This report estimates the capital investment and operating cost of recovering 325 MMft3 of methane gas per year and the selling price of approximately 317 MMft3 of gas per year. The labor, equipment, and supply requirements were determined from those of a previous directional hole drilled at the Emerald Mine, near Waynesburg, PA. The cost of equipment, materials, services, and labor are in third quarter 1982 dollars. They were obtained from vendors, contractors, and the U.S. Department of Labor. Findings indicate a total capital investment of $1,381,160. Annual operating cost amounted to $167,690. At a wellhead price of $2.05 per thousand cubic feet, the sale of approximately 317 MMft3 of gas per year results in a rate of return on investment of approximately 25 pet.

Jan 1, 1984