Search Documents

A study was conducted by the Bureau of Mines to evaluate natural gas as an automotive fuel and to provide guidelines for optimum engine adjustments for low exhaust emissions. The study was conducted using a single-cylinder engine, a multicylinder engine, and a total of eight vehicles. Results from single-cylinder engine tests showed that the light-load, lean-limit misfire region for natural gas begins at an air-fuel ratio between 150 and 160 pct of stoichiometric. Changes in ignition timing significantly influenced emissions of nitrogen oxides and hydrocarbons, but had little effect on carbon monoxide emission. Low emissions can be achieved with current-design engines by adjustment of engine parameters, but only with heavy penalty to engine performance. Emissions from vehicles fueled with natural gas are virtually unaffected by ambient temperature change within the range 20° to 100° F. The organic emissions from engines fueled with natural gas were estimated to be 22 to 25 pct as reactive as the emissions produced using gasoline. Levels of exhaust emissions from vehicles fueled with natural gas were unchanged over 10,000 miles of normal driving.

Jan 1, 1973

Most laboratory sealant studies were carried out in 2.0 inch I.D. Plexiglas tubes of 9.0 inches height containing 4.0 to 4.5 inches reconstructed soil from an 0-8 or 8-16 inch soil horizon at the Lanse site. (When soil was used from the Kato site, the top soil horizon was approximately 0-4 inches. The 4-8 inch horizon was somewhat comparable to the Lanse 8-16 inch horizon.) A 20 mesh Saran or steel screen was placed over the rubber stopper with a bottom drain to a 100 ml measuring cylinder. In some earlier experiments a 1/2 inch bed of 1/4 inch pea-gravel was then added, but in later experiments this was eliminated as it showed no particular utility. Field soil samples collected by a shovel were stored in sealed containers and sieved through a 4 mesh screen just before use. (Moisture content was typically about 25% for A horizon soil and about 20% for B horizon soil.) The sieved soil minus roots was then added in increments of about 1 1/4 inches. Compaction was effected by dropping a weighted ramrod (1-7/8 inches O.D,) five times from a height of two inches. If about twenty tamps were used or if the soil columns were rapped vigorously while water-logged, compaction was high with no detectable percolation. Freezing such samples would then usually cause very slow percolation, e.g. 1-2 ml/day. Using this as a standard procedure, percolation flows were usually stablized after two to three days to rates of about 100 to 200 ml/hour. Percolate was recycled carefully to minimize disturbance of the soil surface. When percolation flows were about 100 to 200 ml/hour, various additives (sealants) were introduced to the moist column in two to three increments to maintain a slight head. Additive concentrations were usually 2-1/2% with some at 5% in earlier experiments. Typical use of 40 ml of 2-1/2% additive corresponds to 4400 lbs/acre. When no more additive was present as supernatent liquid, water washes of about 15 ml were then used several times followed by special additives as needed. More water washes were then used to maintain a head of about 1/2 inch. Percolate was collected in 100 ml cylinders to measure percolation rates in ml/hr. Turbid percolate was evaporated to determine amount of eluted latex. Percolate was sometimes checked for pH by Pan-pH Indicator Paper9,10 reading in 0.5 units. Surface tension measurements were sometimes made by a DuNouy tensiometer10 in experiments using a surfactant for pretreatment.

Jan 1, 1972

By R. A. Kearns

To enable the mining industry to be kept informed as to the availability of equipment developed by mining equipment manufacturers in their constant endeavor to keep a step ahead of changes in mining techniques, the Bureau of Mines periodically issues lists of equipment approved subsequent to the last previous listing. The present list covers those approvals issued during calendar years 1953 and 1954. It supplements Bulletin 543, Permissible Mine Equipment Approved to January 1, 1953. The procedure established in Bulletin 543 of numbering items in each category consecutively to indicate the chronological order of the approvals has been continued in this circular. Information on approvals issued later than January 1, 1955 may be obtained by referring to Coal Age, a monthly magazine issued by the McGraw-Hill Publishing Co.

Jan 1, 1955

By W. H. Kerns

The Simon & Coles manganese deposit in Sherman Valley, Bedford County, Pa., was investigated by the Bureau of Mines during the fall of 1942. Two churn-drill holes; 65 and 75 feet deep were bored, and 8 channel samples were taken. Manganese occurs at this property in the form of psilomelane and manganiferous iron as replacement of the red sandy shale of the Much Chunk-formation. Two cars of manganese ore had been shipped by the owners in 1940, of which one averaged 10.9 percent manganese and the other 21.3 percent manganese. One car of hand-sorted manganese ore that averaged-45 percent manganese was shipped in 1942.

Jan 1, 1948

By R. G. Meara, O&apos

The land-pebble district of Florida, which in 1928 supplied 96.7 per cent of the phosphate production of that State and 82 per cent of the domestic requirements of the United States, is centered in Polk and Hillsboro Counties about 30 miles east of Tampa The deposits are unconsolidated sediments occurring as beds of phosphate matrix overlain by a mantle of barren sands and clays. The matrix consists of a mixture of Sand (quartz grains), clay, and phosphate rock in which the coarsest sand is much finer than the coarsest phosphate; that is, the sand is segregated in the fine material. Before the introduction of classifiers the concentration consisted of log washing, and screening at about 20-mesh, which was usually the finest size that could be taken to maintain commercial grade, 66 per cent B. P. L. (bone phosphate of limey or more. When classifiers were introduced some of the fines that had escaped at the head of the washery and some of the minus 20-mesh material isolated during the rushing and formerly lost supplied the feed.

Jan 1, 1931

By Boyd Guthtrie

[Methods of distilling topped crude oils and distillates under vacuum, accompanied by good fractionation, have taken a place of major importance in the refining industry. In the refining of petroleum products it is generally desirable to produce a distillate of good quality, and this objective is attained by fractionation of a high degree. The laboratory and commercial practice have proved chat by varying the amount of fractionation the quality of the distillate car be changed, and refiners are cognizant of the advantages of good fractionation. Distillation-under high vacuum, however, is a relatively new practice in petroleum refining, and only during the last few years has there boon an indication that that this method ray become a general practice in the industry. Vacuum distillation offers many advantages over older methods of distilling petroleum products. Vacuum combined with steam distillation, for example, is replacing straight-stream distillation because the quality of the products of vacuum and, steam distillation surpasses that of those produced by straight-steam distillation. Although the injection of varying amounts of steam in a vacuum unit is common practice, the amount of steam used is becoming less as the vacuum within the unit is increased. This report describes tie construction of a visible-action laboratory batch still and fractioning; column and. gives curtain data pertaining to the operation of the apparatus under vacuum for the production. of lubricating distillates. The apparatus was designed and built to produce lubricating distillates under as nearly ideal conditions as possible, in order that a subsequent study of the characteristics of the distillates could be made.]

Jan 1, 1932

By Douglas A. Crum

The Taylor's friction circle method for slope stability analysis can be extended to incorporate multiple circles defining the slip surface in a failure mechanism so that it is a workable method for bearing capacity calculations of foundations and rotational failures of retaining walls and similar structures. The U.S. Bureau of Mines has further extended the multiple-circle method to include friction in the material strength and to utilize computational schemes such that this method can be programmed with optimization capabilities rather than being used as a graphical or semigraphical method. Some examples are given that demonstrate ultimate bearing capacity calculations of embedded foundations with eccentric loads and nearby slopes.

Jan 1, 2010

By William J. Campbell

The purpose of this investigation by the Federal Bureau of Mines was to design and construct a fluorescent X-ray spectrograph for dynamic rate studies of selective oxidation in molten metals and to establish basic principles for interpretation of data obtained by this method. An X-ray spectrograph was constructed in which the sample holder is a resistance wound furnace; it was operated up to 800° C. in oxidizing atmospheres. No difficulties were experienced with the cooling or heating systems nor with the protective layer of mica around the X-ray tube window, even though the oxidizing surface of the metal is only 0.5 inch from the X-ray tube window, Means are provided for heating under controlled atmospheres for selected time? temperature cycles.

Jan 1, 1961

By James S. Browning

Heavy liquids have been used to separate minerals of different specific gravities for many years.4 5 6 7 8 9/ The method permits substantially quantitative evaluation of a variety of minerals and requires much less time than the usual methods of chemical analysis. This Bureau of Mines investigation was conducted to determine the applicability of heavy liquid mineral separation to the evaluation of certain spodumene and kyanite ores, prepared mixtures, and plant products. After careful standardization of the particular mineral and associated gangue, estimates of chemical analyses could be obtained from results of heavy liquid separations.

Jan 1, 1960

By E. G. Noble

The effects of HBr concentration and temperature on the solubility and hydration state of AlBr3,' CoBr2, PbBr2, MnBr2, KBr, and NaBr were investigated by the Bureau of Mines. Saturated aqueous solutions of the AI, Pb, K, and Na bromides were sparged with HBr gas at 20°, 40°, and 60° C, and saturated solutions of Co and Mn bromides were sparged at 20° C. Increased HBr concentration caused decreased salt solubility because of the common ion effect for all the investigated bromides except PbBr2. Aqueous solubilities at 20° C were, in percent, 51.7 for AlBr3, 53.2 for CoBr2, 1.1 for PbBr2, 59.6 for MnBr2' 39.5 for KBr, and 47.4 for NaBr. At 60° C, the solubilities were, in percent, 53.3 for AlBr3, 2.2 for PbBr2' 46.0 for KBr, and 53.8 for NaBr. Solubilities in solutions sparged to HBr saturation at 20° C were, in percent, 0.5 for AlBr3, 42.0 for CoBr2, 32.2 for PbBr2, 21.0 for MnBr2, 0.6 for KBr, and 0.3 for NaBr. At 60° C, the solubilities at HBr saturation were, in percent, 1.8 for AlBr3, 41.4 for PbBr2, 1.3 for KBr, and 0.4 for NaBr. CoBr2 precipitated out to a minimum solubility of 27.2 pct at 28.7-pct-HBr concentration. Further increases in HBr concentration increased CoBr2 solubility because of the formation of bromide complexes. PbBr2 in-creased in solubility as HBr concentration increased.

Jan 1, 1988

By H. M. Smith

The production of oil during the early development of new oil fields is usually accompanied by large quantities of natural gas. Since in most fields gas under pressure is the main source of the energy causing the oil to move through the sands into the wells and thence to the surface, coincident production of natural gas will continue as long as present-day producing methods are used. Generally the use of this gas is restricted, since markets are not readily available. Consequently, a large portion of the gas produced is often wasted by being blown into the air. The magnitude of gas waste is well brought out in the following statement by Miller: Only a few outstanding examples need be cited to show the enormous production of gas that accompanies the discovery of new sources. In April, 1927, the Ventura field produced approximately 210,000,000 cubic feet of gas a day; and during the summer of 1927 Alamitos Heights reached a peak gas production of 102,000,000 cubic feet a day; on December 1, 1928, as a result of the summer's deeper drilling in the Long Beach field, surplus gas production amounted to 125,000,000 cubic feet a day. It is estimated that in January, 1929, the Santa Fe Springs field will have a daily gas production of 387,000,000 cubic feet from the recently discovered Buckbee oil zone. Of this amount 274,000,000 cubic feet a day will be the surplus above the amount required for field and plant fuel, taken out by utility corporations, and that used in repressuring the Meyer sand which lies above the Buckbee zone. Another example of the waste of large volumes of gas is in the Turner Valley field of Canada, 6 where 250,000,000 cubic feet of gas is being burned daily in flambeaus, as there is no present outlet except at prohibitive cost.

Jan 1, 1931

By J. B. Gayle

Oven widths for experimental and commercial slot-type ovens differ appreably in most instances; the experimental ovens usually ranging from 10 to 14 inches and the commercial units from 14 to 21 inches. Application of results obtained with experimental ovens to commercial practice thus requires major extrapolations. A critical survey of the literature indicated that sufficient information about the effects of variations in oven width on the carbonizing process is not available to permit such extrapolations to be made with any considerable degree of confidence.

Jan 1, 1960

By Danqing Xu, A. W. Khair

"This paper presents a laboratory simulation of regrinding and resulting dust generation. An Automated Rotary Coal Cutting Simulator (ARCCS) was modified to conduct regrinding experiment. In order to estimate the effects of coal properties and operating parameters on regrinding and dust generation, an orthogonal fractional factorial experimental design was implemented in regrinding experiment. Marple personal cascade impactors, Series 290, were used to measure dust concentration during experiment. Three types of coal seams, namely, Waynesburg, Pittsburgh, and Lower Kittanning, were used to represent different coal properties. Experimental results and complete parametric analysis were presented.In a rotary cutting system, all the broken coal and part of the remaining coal from previous cutting cycles must be transported through part or entire circumference of the cutting drum. This transportation of already recovered coal through the cutting zone of rotary head makes it a rotary grinder. Some of the coal particles will be subjected to secondary fragmentation or regrinding in the process. The potential effect on dust generation by regrinding is significant because the cutting head utilizes kinetic energy to comminute recov¬ered coal material. The moving bits and bit blocks on the cutting head impact coal particles and transfer some of their kinetic energy to the particles. After obtaining kinetic energy, coal particles are free to impact one another and they also impact the coal seam or cutting head. During impact, high impact force and high internal stress concentration are created in the particles. Kinetic energy is transformed into strain energy. When stored strain energy exceeds allowable strain energy, the particles will break. A great amount of respirable dust will be generated due to impact failure. In reality, regrinding occurs at the same time as primary cutting. The particles to be ground are the result of primary cutting. Both primary cutting and regrinding produce dust. Therefore, it is impossible to separate regrinding from primary cutting. In order to study respirable dust generation by regrinding and analyze the influencing parameters, a laboratory approach was adopted. In this approach, it is possible to study the regrinding separating from primary cutting."

Mar 1, 1992

By Robert W. Freedman, Robert L. Craft, William G. Humphrey

As part of a continuing effort to reduce the weight and bulk of equipment that mining personnel must carry underground, the Bureau of Mines and the Mining Enforcement and Safety Administration (MESA) investigated accurate and convenient gas samplers for use by mine inspectors in sampling mine atmospheres. The samplers are septum-stoppered glass vials commonly used for routine blood sampling. These lightweight, compact samplers yield results comparable with those obtained with conventional bottle samplers of 250-ml nominal capacity.

Jan 1, 1975

By A. J. Kraemer

This report on the physical and chemical properties of crude oils of California is one of a series on the producing districts of the United States. It includes a short discussion of results, tabulated data, and individual analyses of California crudes. Analyses of crude oils from the fields of Fresno, Kern, Los Angeles, Orange, and Ventura Counties have been published in Serials 25952 and 26083. The analyses reported in this paper corer samples that were obtained subsequent to the publication of Serials 2535 and 2608. The samples were obtained by members of the San Francisco office of the Bureau of Mines. The collecting of samples was facilitated by the courtesy of representatives of oil companies in California.

Jan 1, 1927

By J. G. Kirby

According to the Bureau of Mines annual survey, there were 318 petroleum refineries in the United States with a total daily crude throughput capacity of 8,632,390 barrels as of January 1, 1956. Compared with the previous year the total number of refineries declined 8 while the crude throughput capacity increased 211,760 barrels daily. Three refinery districts accounted for 90 percent of the crude-oil capacity increase, the California district 34 percent; the Texas Gulf Coast district, 31 percent; and the Indiana-Illinois-Kentucky district, 25 percent. Decreases in capacity during the year were reported for the East Coast, Appalachian #1, and the Arkansas-Louisiana Inland districts. The capacity of the average refinery to process crude oil increased during 1955 from 25.830 barrels daily to 27,145.

Jan 1, 1956

By Joe N. Magee

As part of the important program of promoting conservation and efficient utilization of petroleum, Bureau of Mines engineers are making studies of secondary oil-recovery projects throughout the United states and publishing reports setting forth the pertinent facts so that others may profit by the experience gained. This report presents the results of a study by engineers of the Bureau of Mines, stationed at Franklin, Pa., of secondary oil recovery in a part of the Cabin Creek field, Kanawha and Boone Counties, W. Va., where natural gas is injected into the reservoir to stimulate oil production. Most oil produced in the Appalachian region at present is obtained from stripper fields in which almost all natural energy has been dissipated. Secondary-recovery methods are used extensively in many oil-producing areas of New York, Pennsylvania, West Virginia, Ohio, and Kentucky for recovering oil not produced by primary-production methods. The part of the Cabin Creek field reported in this study is shown in figure 1 and has been designated by the operator as project 4. In 1944 the developed area of the entire field was approximately 4,200 acres, and the area of project 4 was about 600 acres. In the developed area of the project the oil reservoir is in the Berea sandstone and occurs at 2,914 to 3,410 feet.

Jan 1, 1952

By Richard D. Miller

The helium resources base of the United States was estimated by the Bureau of Mines to be 1,070 Bcf as of January 1, 1985. These resources are divided into four categories in decreasing degree of assurance of their existence: (1) helium in storage and in proved natural gas reserves, 280 Bcf, (2) helium in probable natural gas resources, estimated at 243 Bcf, (3) helium in possible natural gas resources, estimated to be 287 Bcf, and (4) helium in speculative natural gas resources, which makes up the remaining 260 Bcf. These helium resources are further divided into depleting, non-depleting, and stored classifications. The depleting resources are those associated with natural gasfields that are, or will be, produced for the natural gas they contain. Almost all of the helium in potential (probable, possible, and speculative) natural gas resources is included in this classification. These depleting resources are estimated to contain 900 Bcf of the total helium resource base. Helium resources contained in nondepleting natural gas resources, those in shut-in, abandoned, or otherwise nonproducing natural gasfields, are estimated to total 133 Bcf. There is 37 Bcf of helium in storage in the Federal Government-owned Cliffside Gas Field near Amarillo, TX.

Jan 1, 1987

By Paul M. Tyler

Graphite is chemically identical with diamond, both being crystallized allotropic forms of carbon. Graphite obviously differs greatly from diamond in physical properties and is easily recognized by its blackness, its softness (1 to 2 on Mohs' scale), and its slick feel when rubbed between the fingers. Strictly speaking, all graphite is crystalline, but grades in which the individual grains cannot be distinguished with the naked eye are commercially classed as amorphous. Natural mixtures of the two varieties occur in all proportions, and the classification of a given sample as "amorphous" or "crystalline" graphite is based largely upon trade practice. Until recently different varieties of vegetable or animal charcoal, lamp black, soot, gas carbon, and coal ware considered strictly amorphous, but modern examination by X-ray methods indicates that even these materials possess the same internal crystalline structure as graphite, differences in physical properties being perhaps explained by porosity or presence of combined hydrogen or other impurities.

Jan 1, 1941

By Murray Greyson

A number of tests were made with various methanation catalysts in fixed-bed, conventional fluidized-bed, and multiple-feed, fluidized-bed equipment to develop catalysts and processes for methanation of synthesis gas. The results show: 1. Methanation reactions may be carried out in 1-inch, bench-scale equipment at high synthesis-gas throughputs with good temperature control of the reactions if a multiple-feed type of fluidized-bed design is used. 2. Nickel is superior to iron as a catalyst for the methanation of synthesis gas, unless the process is considered in terms of a combined operation that produces both gaseous and liquid products. 3. Techniques of catalyst preparation determine, to a large extent, the process life of nickel catalysts, and these techniques must be thoroughly investigated before any conclusions can be reached. 4. Enough data are available to indicate that the sulfur concentrations in synthesis gas that is used for methanation are extremely critical, and maximum process limits should be carefully evaluated.

Jan 1, 1955