Search Documents

By Alan D. Hartman

Instabilities in electric steelmaking furnace arcs cause electrical and acoustical noise, reduce operating efficiency, increase refractory erosion, and increase electrode usage. The U.S. Bureau of Mines is investigating methods to stabilize these arcs. To perform experiments to test new hypotheses, Bureau researchers designed and instrumented an advanced, experimental single-phase furnace. This report describes this furnace, which was equipped with high-speed data acquisition capabilities for electrical, temperature, pressure, and flow-rate measurements; automated atmosphere control; ballistic calorimetry; and view ports for high-speed cinematography. Precise environmental control and accurate data acquisition allow the statistical design of experiments and assignment of rigorous confidence limits when potential furnace or procedural modifications are tested.

Jan 1, 2010

Multiple-seam interactions are a major ground control hazard in many U.S. underground coal mines. In some U.S. coalfields, particularly in central Appalachia and the West, the majority of today’s mines are operating above and/or beneath previously mined seams. The effects of multiple-seam interactions can include roof falls, rib spalling, and floor heave. These can seriously disrupt mining operations and threaten the safety of miners. In early 2006, a West Virginia coal miner was killed by rib roll that occurred in a high-stress zone beneath a remnant structure in an overlying mine. Fortunately, not every multiple-seam situation results in hazardous conditions. Indeed, the vast majority do not. For the past several years, the National Institute for Occupational Safety and Health has been conducting research to develop better techniques for predicting the location and severity of multiple-seam interactions. During this investigation, more than 50 mines were visited across the U.S. coalfields. Nearly 300 case histories were collected and analyzed using multivariate statistical techniques. The study also employed the numerical model LaM2D to estimate the multiple-seam stress, the Analysis of Longwall Pillar Stability (ALPS) and the Analysis of Retreat Mining Pillar Stability (ARMPS) programs to determine pillar stability factors (SFs), and the Coal Mine Roof Rating to measure roof quality. The study focused on the two most common types of multiple-seam interactions: • Undermining, where stress concentrations caused by previous full extraction in an overlying seam is the main concern; and • Overmining, where previous full extraction in an underlying seam can result in stress concentrations and rock damage from subsidence. The study confirmed that overmining is much more difficult than undermining, and isolated remnant pillars cause more problems than gob-solid boundaries. For the first time, however, it was possible to quantify these effects in terms of the equivalent thickness of interburden needed to compensate for them. The study also found that pillar design is a critical component of multiple-seam mine planning. Many of the failed cases involved pillars whose SF seemed inadequate once the multiple-seam stresses were accounted for. Weaker roof was also found to significantly increase the risk of multiple-seam interactions. The most important result of the study is an equation that predicts the critical thickness of the interburden required to minimize the likelihood of a multiple-seam interaction. This equation was incorporated into a step-by-step methodology that allows mine planners to evaluate each potential interaction and take steps to reduce the risk of ground control failure. Such measures could include installing cable bolts or other supplemental support, increasing the pillar size, or changing the mine layout to avoid the remnant structure entirely. These Proceedings also contain several previously published papers that cover other facets of multiple-seam mining research. Two papers describe the LaModel family of software developed by Professor Keith A. Heasley of West Virginia University. The LaModel programs were designed for calculating the stresses and displacements in coal mines or other thin, tabular seams in layered media. The original three-dimensional version of LaModel is essential for detailed analyses of complex multiple-seam scenarios. LaM2D, by contrast, implements a simplified two-dimensional model that is suitable for quick approximations of the multiple-seam stresses and strains. Three additional papers in these Proceedings describe the extensive multiple-seam experience of the Harris Mine, examples of extreme multiple-seam mining from the central Appalachian coalfields, and longwall mine experiences in Pennsylvania, West Virginia, and Utah. The final paper reports on a numerical modeling study that provided some insight into the mechanics of multiple-seam mining.

Jan 5, 2007

By Benjamin W. Haynes

Cement kiln dust (CKD) produced in the contiguous United States and Hawaii was characterized as part of the Bureau of Mines' program in minerals environmental technology. The mineralogical and chemical composition was determined for 113 CKD samples from 102 plants that normally send CKD waste to landfill. Characterization included the determination of 28 elements, 7 anion species, carbon dioxide, noncarbonate carbon, and chemically bound water. Mercury was determined in 15 samples. Interelement correlation coefficients were determined for 23 elements, 5 anions, CO2, noncarbonate carbon, and chemically bound water. To assess the hazardous waste potential of CKD, the U.S. Environmental Protection Agency Extraction Procedure (EP) toxicity test was performed on all 113 CKD samples. All but one sample were in compliance with the test; the noncomplying sample slightly exceeded the EP toxicity test criterion for lead.

Jan 1, 1982

By T. C. Atchison

This report describes a mobile laboratory designed and constructed by the Bureau of Mines in 1950 to meet the needs of an experimental blasting research program. The laboratory has facilities for making; film recordings of 16 simultaneous transient electrical signals over a broad range of amplitude, frequency, and duration. The signals are recorded with specially designed oscilloscopes and high-speed drum cameras. Each of the 16 channels records on a separate strip of 35-millimeter film by using interchangeable input units, transducers having different sensitivities and output impedances can be accommodated. The laboratory can be used to record both steady-state and transient phenomena originating as electrical voltages or capable of being converted to electrical voltages by appropriate transducers. Thus, the laboratory can, be used in studying various types of vibration problems or high-speed phenomena, such as ground and building vibrations, machinery vibrations, airborne vibrations, electrical-circuit switching phenomena, millisecond timing, and seismic phenomena occurring when rock is broken by explosives.

Jan 1, 1956

By J. W. Miller

This report deals with upgrading of the coal reserves of Raleigh County, VI. Va., to metallurgical standards. The data on samples herein correctly show the characteristics of the bed at the point where sampled and are used to indicate the general quality of the bed in the county. The principal results and conclusions are: 1. Raleigh County contains large reserves of high-quality, high-, medium-, and low-volatile coals. 2. The principal beds from which an increased amount of coal is expected to be mined in the future are: The Eagle, Powellton, No. 5 Block, Hernshaw, Fire Creek, and Pocahontas No.6.

Jan 1, 1954

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations No. 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the seventeenth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project, except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes.

Jan 1, 1948

By Jürgen F. Brune, R. Karl Zipf, Michael J. Sapko

Seals are barriers constructed in underground coal mines throughout the United States to isolate abandoned mining panels or groups of panels from the active workings. Historically, mining regulations required seals to withstand a 140-kPa (20-psig) explosion pressure. However, the Mine Improvement and New Emergency Response Act (“MINER Act”) requires the Mine Safety and Health Administration (MSHA) to increase this design standard by the end of 2007. This report provides a sound scientific and engineering justification to recommend a three-tiered explosion pressure design criterion for new seals in coal mines in response to the MINER Act. Much of the information contained in this report also applies to existing seals. Engineers from the National Institute for Occupational Safety and Health (NIOSH) examined seal design criteria and practices used in the United States, Europe, and Australia and then classified seals into their various applications. Next, the engineers considered various kinds of explosive atmospheres that can accumulate within sealed areas and used thermodynamic calculations and simple gas explosion models to estimate worst-case explosion pressures that could impact seals. Three design pressure-time curves were developed for the dynamic structural analysis of new seals under the conditions in which those seals may be used: unmonitored seals where there is a possibility of methane-air detonation or high-pressure nonreactive shock waves and their reflections behind the seal; unmonitored seals with little likelihood of detonation or high-pressure nonreactive shock waves and their reflections; and monitored seals where the amount of potentially explosive methane-air is strictly limited and controlled. Figure 1 is a simple flowchart that illustrates the key decisions in choosing between the monitored or unmonitored seal design approaches and the three design pressure-time curves. For the first condition, an unmonitored seal with an explosion run-up length of more than 50 m (165 ft), the possibility of detonation or high-pressure nonreactive shock waves and their reflections exists. The recommended design pressure-time curve rises to 4.4 MPa (640 psig) and then falls to the 800-kPa (120-psig) constant volume (CV) explosion overpressure. For unmonitored seals with an explosion run-up length of less than 50 m (165 ft), the possibility of detonation or high-pressure nonreactive shock waves and their reflections is less likely. A less severe design pressure-time curve that simply rises to the 800-kPa (120-psig) CV explosion overpressure may be employed. For monitored seals, engineers can use a 345-kPa (50-psig) design pressure-time curve if monitoring can ensure that (1) the maximum length of explosive mix behind a seal does not exceed 5 m (16 ft) and (2) the volume of explosive mix does not exceed 40% of the total sealed volume. Use of this 345-kPa (50-psig) design pressure-time curve requires monitoring and active management of the sealed area atmosphere. These design pressure-time curves apply to new seal design and construction.

Jan 7, 2007

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations No. 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the fifth. The data are accompanied by maps showing the location of holes drilled and deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in Volume I. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion of that area.

Jan 1, 1948

By G. R. Strimbeck

This is a report on experimental work on development of a gasification process operating at near atmospheric pressures and using finely pulverized coal entrained in oxygen and steam. The gasifier was designed by The Babcock and Wilcox Co. in cooperation with engineers of the Bureau of Mines Morgantown station. The test work discussed in this report covers the first 34 tests made in the pilot plant in which a strongly coking Sewickley-bed coal, ground to either 70 or 90 percent through a 200-mesh screen, was used.

Jan 1, 1954

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigations beginning with No. 4251, of which this is the third. The data are accompanied by maps showing the location of holes drilled and deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township-map. The description of each half township is followed by a description of each deposit developed in that half township.

Jan 1, 1948

By Franklin D. Cooper

The value of nonfuel mineral raw materials produced in the United States in 1978 was $20 billion. In 1979, total value increased to an estimated $24 billion, up 20% from 1978. Of the principal metallic ores produced in 1979, about half showed increased quantitative output and all showed increased value per ton compared with that of 1978. Most nonmetallic commodities showed increases in quantitative output and in average value per ton. Because of its decreasing share of the world market, the domestic mineral industry's concerns were the increasing costs of capital, labor, and energy; withdrawals of public lands from mining; and the increasing cost of environmental regulations that tended to deter or delay investment in the Nation's capacity for producing essential minerals.

Jan 1, 1980

By Carlton E. Brown

This report contains information on the relation between and precision or reproducibility of counts (light-and dark-field) of the dust in liquid from simultaneous impinger, midget-impinger, electric-precipitator, and filter-paper samples. The impinger was the main sampler used from about 1922 to 1939 by industrial hygienists in the United States for collecting samples of unhygienic dust from the atmospheric environment of workers. The midget-impinger, a small modification of the preceding impinger described in 1937, has been the sampler used most since about 1939. Electric precipitators5/6/ have been used to a limited extent, mainly by the Bureau of Mines in the laboratory, for obtaining results comparable to impinger results. A filter-paper sampler for obtaining results comparable to impinger results has been described by Brown. All these samplers have a high collecting efficiency for particles larger than 1 micron in diameter revealed by the usual light-field counting procedure. However, their collecting efficiencies are quite variable for the smaller particles revealed by the dark-field counting procedure used in this study. Published information on the relation between the results of these samplers is limited and scattered. Summaries of some of this information are given in this report along with some previously unpublished information.

Jan 1, 1949

By John W. Walkiewicz

The U.S. Bureau of Mines has conducted studies to utilize rapid microwave heating to stress fracture ore samples. Iron ores containing hematite, magnetite, and goethite were subjected to microwave energy in batch operations at 3 kW and heated to average maximum temperatures between 840 and 940 °C. Standard Bond grindability tests showed that microwave heating reduced the work index of iron ores by 10 to 24 pct. In a microwave chamber designed to simulate a continuous throughput operation at 3 kW, the grindability of a taconite ore was improved by 13 pct at a bulk temperature of 197 °C. Because stress cracking occurred at a lower temperature, less energy was consumed. To further improve the economics of microwave fracturing, higher powers up to 16 kW were used to rapidly heat samples to relatively low temperatures in a continuous, belt-fed applicator. A significant improvement of grindability was obtained with a larger rod mill feed size in comparison to a minus 6-mesh Bond feed.

Jan 1, 2010

By Manuel Gomez

Published experimental coke data from a pilot plant slot-type oven were examined by statistical regression analysis. Quantitative relationships were found to exist between the coking rate, bulk density, and fine grinding of the coal, sole-oven expansion, volatile matter, moisture, ash, and carbon con-tent of the coal and coke parameters indicative of size and strength. Regression equations developed from coke data were shown to yield computed values that were in good agreement with experimental results for 11 coke properties. Prediction equations developed were evaluated with an independent set of data. Present results indicate that the variables cited undergo much interaction and the sum of these interactions determines coke size and strength.

Jan 1, 1967

By John E. Hamak

The U.S. Bureau of Mines estimates the identified helium resources of the United States at 630 Bcf as of December 31, 1990. This includes 295 Bcf of demonstrated reserves, 87 Bcf of demonstrated marginal reserves, and 42 Bcf of demonstrated subeconomic resources. The identified resources include 161 Bcf of helium in inferred and marginal reserves and 45 Bcf in inferred subeconomic resources. The identified helium resources contained on Federal lands are approximately 170 Bcf, including 32 Bcf in underground storage in the Cliffside Gasfield near Amarillo, TX. In addition to the identified helium resources, undiscovered helium resources in the United States are estimated at a most likely volume of 103 Bcf, with a maximum volume of 259 Bcf and a minimum volume of 41 Bcf. Also reported are 43 Bcf of helium in nonconventional and low-helium-content natural gases. Current extraction of helium in the United States occurs mostly from natural gases produced from the Hugoton gas area in Kansas, Oklahoma, and Texas, and the Riley Ridge area in southwest Wyoming. Helium extracted from natural gas in the United States in 1990 was 2.5 Bef. If current trends continue, some shortfalls in helium supply may occur in about 5 to 10 years.

Jan 1, 1993

By G. S. Rice, R. V. Wheeler

"In September 1923, a proposal was made through official diplomatic channels by the British Safety in Mines Research Board to the United States Bureau of Mines for ""closer cooperation between the two countries in investigations into the causes and means of prevention of mining dangers."" This proposal was cordially accepted by the Bureau of Mines and was officially approved.In the spring of 1924 cooperation was .formally begun. It contemplated, as stated officially, ""full exchanges of information, a joint program of research, and periodic exchange of personnel so as to assure concordant results. By making the resources of both organizations available it will hasten the attainment of results, will secure better: checks for, accuracy, and in the end will save money for both by avoiding duplication and repetition.""This joint work has been carried-on successfully since that time and has developed valuable results, reports on which have been issued from time to time. The progress report which follows gives the results of the studies and work carried on in 1929.During 1929 all the phases of our cooperative research, begun in previous years, have developed normally. The exchange of formal monthly reports on all programs of mutual interest has been continued and has proved an invaluable, means of maintaining contact between the investigators of both organizations. There has been no diminution in the exchange of routine progress reports on specific subjects or in direct correspondence. The interchange of personnel has been maintained, and we can say that the mutual benefits to be derived from this form of cooperation are so great as to be difficult to overestimate. It leads to an appreciation of methods of research and modes of thought in the interpretation of results obtainable in no other way, and engenders a frankness and intimacy which must continuously enhance the value of future cooperation.Dr. S. R. Katz, who was assigned for service with the Safety in Mines Research Board in April, 1928, returned to America in May, 1929. During his stay in England he completed, in cooperation with members of the board's staff, the equipment of a gas-mask laboratory and designed and tested a new form of gas-mask canister. A publication of the Safety in Mines Research Board dealing with this investigation has been prepared and approved and will .be .issued in the near future. In additions Dr. Katz imparted to those with whom he was associated much of his knowledge and technique regarding his particular subjects. He delivered two lectures to the board's staff, the subjects be ""Gas Masks"" and ""The Intensity of Odors"", and gave papers before the Midland Institute of 'lining Engineers and the Birmingham University Mining Society on the subject of ""Industrial Gas Masks""."

Jun 1, 1930

By W. H. Frederic, F. H. Gibson, R. F. Abernethy

This publication contains the quantitative values for phosphorus , chlorine , sodium , and potassium in United States coals . The samples tested were taken from commercial shipments and have been selected to represent the principal coal producing areas of the country . Due to combining the analytical results from two separate surveys , values for the four elements are not available for all samples .

Jan 1, 1965

By Roy E. Peterson

The Bureau of Mines conducted an investigation to produce metallized pellets from domestic iron ore superconcentrates using lignite and subbituminous coal as reductants. Feed materials for the metallizing process consisted of commercially indurated iron oxide pellets and green pellets prepared from upgraded domestic concentrates with graphite or limestone as internal additives. Durability of the green pellets during metallization was investigated in tests conducted in a 7-inch-ID rotating drum furnace. Test results indicated that the major cause of pellet disintegration with the concentrates used was the tumbling action during reduction rather than forces generated within the pellets. In larger scale tests made in a 34-inch-ID by 35-foot-long kiln, the previously indurated pellets were metallized with lignite at 1,030° C with little disintegration. A 96-percent level of metallization was obtained in pellets having an average compressive strength of 420 lb. In subsequent, similar tests using green pellets containing graphite or limestone, pellet disintegration was more severe, with 10 to 40 percent of the feed being lost as dust. The surviving pellets had metallizations ranging from 88.3 to 94.4 percent and compressive strengths ranging from 60 to 68 lb.

Jan 1, 1976

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. This paper is a continuation of a series made in cooperation with the Coordinating Fuel Research (CPR) Committee of the Coordinating Research Council (CRC), Inc. The first of this series of reports presented data on motor gasolines sold during the winter of 1935-36, and succeeding reports described motor gasolines sold during the summers and winters to and including the summer of 1941. No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-43, the semiannual reports were resumed.

Jan 1, 1949

By James A. Wasson

This Bureau of Mines report summarizes the application of pilot flooding in the evaluation of a potential waterflood project. Aspects of pilot flooding discussed include choice of pilot location, confined and unconfined waterfloods, operational precautions, and comparison of predicted with observed performance. Summaries of published methods of pilot flood data analysis for determination of full-scale waterflood feasibility are presented and their use illustrated for example pilot flood data.

Jan 1, 1974