Search Documents

By John W. Frey

This paper presents one of a series of digests of foreign mining legis- lation and court decisions, which is being prepared in advance of a general re- port relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws governing the Portuguese overseas possessions, prepared from the best avail- able information in Washington, has been slightly amplified in accordance with suggestions transmitted through the courtesy of the Department of State by Fred Morris Dearing, American Minister at Lisbon.

Nov 1, 1929

By James A. Morgan

FIELD MEASUREMENTS OF NOISE WERE MADE ON THE PERIPHERY OF ENCLOSURES DESIGNED, MANUFACTURED AND INSTALLED BY INDUSTRIAL ACOUSTICS COMPANY, INC. ON THE SECONDARY TACONITE CRUSHER AT THE JACKSON COUNTY IRON COMPANY PLANT IN BLACK RIVER FALLS, WISCONSIN. NOISE REDUCTION ACHIEVED BY THE ENCLOSURES WAS SUFPICIENT TO PERMIT REDUCTION OF CRUSHER ROOM NOISE TO 90 DBA, PROVIDED THAT OTHER SOURCES ARE APPROPRIATELY TREATED AND ACOUSTICAL ABSORPTION IS PROVIDED IN THE CRUSHER ROOM. SECONDARY CRUSHER NOISE WAS REDUCED 10 TO 15 DBA BY THE ENCLOSURES.

Jan 1, 1980

By Robert J. Hundhausen, GEORGE M. GRISMER

This circular describes the methods and costs of deepening the Silver Summit three-compartment shaft in the Coeur d'Alene mining region of Idaho. A noteworthy rate of advance was achieved at this operation by the successful use of a mechanical shaft-mucking machine. The Silver Summit mine is 1 mile west from the town of Osburn, Idaho, via U. S. Highway 10. The adit-level portal of the mine is on the south slope of the Coeur d'Alene River Valley at an altitude of 2,700 feet. The Silver Summit shaft is 6,000 feet from the portal. In past years this shaft had been sunk from the adit level to a depth of 1,500 feet. During 1946 the Polaris Mining Co, deepened it to 3,095 feet. The work was done under a co- operative development agreement between the Silver Summit Mining Co. and the Polaris Mining Co.

Jan 1, 1948

By W. C. Holliman

This report on the characteristics of commercial aviation gasolines presents compilations of inspection test data furnished on their products by manufacturers of commercial grades of aviation gasoline, and special data obtained in Bureau of Mines laboratories on samples of these gasolines. Data and physical samples for the survey were submitted by 15 manufacturers on 18 grade 80, 21 grade 91/98, 22 grade 100/130, and 10 grade 115/145 aviation fuels.

Jan 1, 1948

By N. S. Raymon

As part of an interegency agreement with the Energy Research end Development Administration to develop unproved refractory materials for use in coal gasification processes, the Bureau of Mines reviewed the literature to determine the effect of steam, H2, CO, and CH4 as well as the alkali metal oxides K2O and Na2O on refractory materials. Emphasis was given to the performance of high-alumina castable and fired refractories to conditions expected in coal gasification processes. Approximately 85 references were reviewed with 40 cited in the text. The literature was found to contain little data directly applicable to the selection of refractory lining materials suitable for use under the conditions of temperature, pressure, and gas compositions expected in second generation coal gasification reactors.

Jan 1, 1976

By R. L. Montgomery

Heats of solution of yttrium chloride and oxide in hydrochloric acid were measured by Bureau of Mines researchers. Using the heat of combustion of yttrium mentioned in the literature, the Bureau calculated the heat of formation of yttrium chloride to be -239.16 + 0.50 kcal./mole. The Bureau experiments gave evidence that the heats of solution of yttrium chloride from the literature are mostly too low because of water and/or oxychloride impurities. Heat of combustion of yttrium (8)3/ and its heat of solution in hydrochloric acid (2, 14) have been measured. The earlier heat of solution measurement (2) is unreliable because of possible potassium contamination (4). Heat of solution of yttrium chloride has been measured by three researchers (3, 9, 15), who obtained widely different results. Spedding and Flynn (14) report the heat of formation of yttrium chloride as -232.69 kcal./mole from their solution studies. The present work was designed to check the reported heats of solution of yttrium chloride and to determine the heat of solution of yttrium oxide. The latter measurement would allow the results of solution and combustion data for yttrium to be intercompared.

Jan 1, 1960

By H. J. Heinen

To maximize productivity through improved minerals processing technology, the U.S. Department of the Interior, Bureau of Mines, is investigating particle agglomeration techniques as a means of increasing the percolation rates of leach solutions in heap leaching of clayey gold-silver ores. Simulated heap leach experiments were conducted on 50-pound charges of ore that were contained in 5.5-inch-diameter columns, 5 feet in height. Results indicated that the percolation rate of cyanide leach solution could be enhanced markedly by mixing the ore with controlled amounts of lime, flocculants, and water, and then aging the mixture prior to the column leach step. Experimental results obtained on 20-mesh silver tailings and gold ore crushed to 3/8 inch and to 1 inch showed that it was possible to increase percolation rates as much as 100-fold without sacrificing silver-gold extraction. Larger scale tests conducted in 24-inch-diameter, 16-foot-high columns closely paralleled bench-scale results. By improving percolation leaching, these techniques have the potential of helping to solve environmental problems associated with tailings disposal as well as making an important economic impact on gold-silver recovery operations. Investigations are continuing to develop binders superior to lime for particle agglomeration pretreatment.

Jan 1, 1979

By James W. Townsend

The Vicksburg mining property lies in the southeastern foothills of the Star mining district, Beaver County, Utah (fig. 1). Within a few miles of the Vicksburg mine, lying in a semicircle from south to northwest, are such past producers of lead-silver ores as the Moscow, Hoosier Boy, Red Warrior, Wild. Bill, Harrington-Hickory, and many others. Farther to the north, in the San Francisco district, are the famous Horn Silver and Cactus mines. The formation at the Vicksburg property consists of interbedded limestone, shale, and dolomitic limestone. These beds have been metamorphosed by the intrusion of irregular masses of porphyritic igneous rocks grading from quartz-monzonite to granodiorite. Ore deposition is in north-trending fissures of sheeted zones, contact metamorphic in type. These depositions were subsequently altered to gossan. A preliminary investigation of the Vicksburg property involving surveying, mapping, and sampling was made by W. A. Young and F. H. Gunnell, engineers of the Bureau of Mines, in the fall of 1946. As a result of the investigation, a project was set up to investigate the possibility of ore occurrence at greater depth on the fissures under the mineralized zone by diamond drilling.

Jan 1, 1950

By Oliver Bowles

"Conservation of slateWaste slate is a problem of outstanding importance in the slate industry, for a very large proportion of all slate quarried is thrown on the waste heap. While many uses for waste slate have been found, the demand calls for merely a fraction of the present supply of unused material. If the slate industry is to increase in prosperity, the producer's energy must be directed toward the development of ways and means of reducing waste to the lowest possible point. The Bureau of Mines of the Department of the Interior has devoted much study to this problem and a recent bulletin ** contains a detailed discussion of the waste problem.Attention has recently been directed toward an improved method of cutting slate in quarries, a method that promises to reduce greatly the percentage of waste material. The method has been introduced since that bulletin was published, and this supplementary paper covers the details of the process.A reversion in method,In connection with this new mode of operation history is repeating itself in a very interesting way, for the old quarry bar used years ago with steam drills, and later discarded in favor of the channeling machine .and the hammer drill, has been salvaged from the scrap heap, and again put to active use. The occasion for its employment is an attempt to improve quarry methods by the substitution of drilling for channeling or blasting."

Oct 1, 1923

By Floyd R. Hertweck

The helium resources of the United States were estimated by the Bureau of Mines to be 1,037 Bcf as of January 1, 1981. These resources are divided into four categories, in decreasing degree of assurance of their existence: (1) helium in storage and in measured natural gas reserves, which totals 211 Bcf, (2) helium in indicated natural gas resources, which is estimated at 207 Bcf, (3) helium in hypothetical natural gas resources, which is estimated to be 318 Bcf, and (4) helium in speculative natural gas resources, which makes up the remaining 301 Bcf. These helium resources are further divided into depleting, nondepleting, and stored classifications, The depleting resources are those associated with natural gasfields that are, or will be, produced for the natural gas they contain. All of the helium in undiscovered (hypothetical and speculative) natural gas resources is included in this classification. These depleting resources are estimated to contain 897 Bcf of the total helium resource base. Nondepleting resources are those in shut-in, abandoned, or otherwise nonproducing natural gasfields. Helium resources contained in nondepleting natural gas resources are estimated to total 100 Bcf. There is 40 Bcf of helium in storage in the Federal Government-owned Cliffside Gas Field near Amarillo, Tex.

Jan 1, 1983

By R. V. Higgins

This paper describes a method and a computer program for calculating shape factors and areas of channels that turn more than 90° and conduct fluids into the backs of wells. The program represents an improvement over a previous Bureau of Mines investigation by using a 4-point Lagrange interpolation equation instead of a 3-point and by summing areas of trapezoids with either x altitudes or y altitudes. Some of the techniques reported in this paper can also be used to compute the areas between contours and the lengths of lines that turn more than 90°.

Jan 1, 1968

By David J. Kusler

This report describes a primary or direct, continuously sampling, and automatically averaging gravimetric method for analyzing gaseous mixtures of carbon dioxide, carbon monoxide) hydrogen, and (by volume measurement) nitrogen. The gaseous mixture is analyzed by passing it at a controlled and definite rate through a system that permits carbon dioxide and water retained by appropriate absorbents to be determined and the residual-gas volume (essentially nitrogen) to be measured. The accuracy and dependability have been established by comparison with very carefully conducted Orsat analyses. The method was developed for, and has been satisfactorily applied to, the analysis of blast-furnace top gas. It permits relatively attention free operation, using simple and low-cost materials usually found as basic equipment in the analytical laboratory. It provides, over a wide range of time or sampling intervals (from less than 1 to over 24 hours), the average composition, in terms of volume-percent, for those components usually determined in blast-furnace gas, if (as is usual) the flow rate of gas from the blast furnace is essentially constant over a selected analysis interval. Oxygen and methane are not determined; but, since these gases are normally absent or present only in traces, their analysis is seldom required.

Jan 1, 1959

By Wallace W. Roepke

The Bureau of Mines studied the cutting characteristics of point-attack bits to reduce airborne respirable dust and energy during cutting. Linear cutting of two coal types using four bit types at three depths of cut with three space-depth ratios was performed with a modified horizontal milling machine using an optical particle-size monitor for respirable dust sampling. The cutting action of one bit on a rotary hardhead mining machine was mathematically analyzed and compared with the results of the linear cutting test. Airborne respirable dust per unit mass cut (specific dust) was found to be a monotonically increasing function of specific energy. Specific dust and energy decrease with increasing depth of cut. The amount of nonairborne respirable dust was 100 to 1,000 times greater than the airborne dust. The plumb-bob bit produced the most airborne respirable dust and the highest specific energy of the four bits tested. Rotary cutting was a greater dust producer and energy consumer than linear cutting because of the constantly changing depth of cut, space-depth ratio, and attack angle of the bit relative to the horizontal bedding planes. A new cutting technique is proposed to minimize the existing problems of the rotary cutting machines by providing greater production, reduced dust, and minimized methane ignition potential at the face.

Jan 1, 1976

Air pollution control regulation$ already implemented or being considered for implementation require substantial investment of capital to remove the sulfur oxides from copper, lead, and zinc smelter gases. There will be an attendant increase in production costs and possibly an associated increase in the price of these metals to the consumer. The total investment and any resultant metal price increase will depend upon the control regulations that ultimately will be adopted by the individual States. Controversy has arisen between the metals industry and governmental control agencies regarding the status of stack gas desulfurization technology and the ability of industry to control sulfur oxide emissions to the degree proposed by some of the more stringent regulations currently under consideration. This paper evaluates the problems involved in achieving various degrees of control over smelter sulfur oxide emissions and the technology available to accomplish the task of assuring clean air. The estimated cost of compliance is reviewed for the copper, zinc, and lead industries, but principal at tent ion is given to the copper situation.

Jan 1, 1971

By E. F. Ferrell

Electrowon molybdenum powders and a commercial hydrogen-reduced powder, all with different minor impurities, were investigated by the Bureau of Mines with respect to inherent properties, to fabrication techniques, and to proper-ties of the fabricated sheet. Compared with the commercial hydrogen-reduced powder, the electrowon powders had a larger particle size, a greater flow rate, a higher apparent density, and a lower oxygen content. Sheet materials prepared from the two types of powders showed similar mechanical properties, under the same conditions of heat treatments, except for low-temperature ductility. Yield strengths varied with carbon content, heat treatment, and test temperature.

Jan 1, 1970

By Lotfollah Nahai

India is one of the fortunate countries that has substantial reserves of many raw materials for producing steel; however, for historical and economic reasons these resources have not been aggressively developed until recently. Production of steel on an industrial scale started in 1912, but annual output was below 1 million tons3 in 1938 and about 1,500,000 tons in 1951. Expansion of the steel industry became one of the objectives of India's economic planning after independence in 1947. The Planning Com¬mission's 1951 report emphasized the importance of steel production, but financial obstacles, emphasis on river valley projects, and priority for increased food production in the First 5-Year Plan (1951-56) did not permit large-scale expansion of steel capacity. The 1956 planned target for crude steel, only 1,650,000 tons, was actually exceeded by production of 1,737,900 tons. In the Second 5-Year Plan (1956-61), however, construction of steel plants received a high priority. Currently three new steel plants, each with an annual capacity of approximately 1 million tons of steel, are nearing completion in Rourkela, Dorgapur, and Bhilai. Simultaneously, the two privately owned steel plants and the small State-owned plant in Mysore have been enlarged and modernized. As a result, India's crude steel capacity will be about 6 million tons in 1961, almost evenly divided between Government-owned and privately owned plants. Actual production in 1960 totaled 3,254,000 tons compared with 2,434,000 tons in 1959. Assuming that the population will be 430 million and that capacity production will be achieved, the 1961 per capita steel output will be only 31 pounds compared with 200 pounds for Japan in 1959. Some Indian experts feel that development of steel-consuming industries merits greater emphasis in the Third 5-Year Plan (1961-66) than expanding existing steel-producing facilities. Nonetheless, the Third 5-Year Plan calls for a 10 million ton annual capacity by 1966 to be achieved by expanding the Government-owned plants in Bhilai, Durgapur, and Mysore, and by establishing a new integrated Government plant in Bokaro, in the State of Bihar.

Jan 1, 1961

By M. J. Ankeny, J. J. Forbes

The United States Bureau of Mines often receives inquiries from the mineral , petroleum , and allied industries concerning the essential steps to be taken in the formation of Holmes Safety chapters and councils . The purpose of this circular is to answer in a general way such inquiries and to relate briefly the history and work of the Holmes Safety Association to the present date .

Jul 1, 1931

By Bernadette C. Michalski

Mineral raw materials, labor, capital, and technology form the basis of industrial production. The augmentation of one or all of the elements--labor, capital, and technology--will result in industrial growth. Thus, an increase in the labor force would increase output. A similar result would be achieved by expanding capital investment and supplying labor with more equipment. Finally, industrial growth can be achieved by introducing more productive methods and techniques born of technological advancement. The Soviet Union has employed these elements in many patterns to catapult from an agricultural to an industrial economy in four decades. The early history of the Soviet Union was marked by limited capital and borrowed technology, forcing the Soviets to concentrate on an abundant labor reserve to support the industrial program. The source of this reserve was the rural population. In [1928], 80 percent of the working population was employed in agriculture. This figure dropped to 43 percent by 1956, whereas industrial employment in the same period increased from 8 to 31 percent.3/

Jan 1, 1960

By Charles H. Atkinson

The Rio Blanco massive hydraulic fracturing demonstration has been undertaken by the Bureau of Mines, Atomic Energy Commission, and a group of 15 industry participants. CER Geonuclear Corp. has been retained as program manager to evaluate the stimulation effects of very long fractures, suitably propped open in thick sections containing multiple intervals of low-permeability gas-bearing sands. The zone of interest for this demonstration includes Fort Union and Mesaverde sands from about 5,800 to 8,.200 feet deep in Rio Blanco County, Colo., about 1 mile from the site of the May 1973 triple nuclear detonation aimed at stimulating production from the same reservoirs. Drilling the test well and evaluating the reservoir prior to fracturing was funded by Government participants; fracturing and production testing will be funded by industry. The test well has row been completed at a total depth of 8,170 feet, and data obtained from logs, cores, production and drill-stem tests indicate reservoir conditions to be less favorable for gas production than anticipated. Structural position is lower than expected, resulting in higher water saturation than was determined for the same sands at the nuclear fracturing location. The lower sands of the Fort Union sequence appear to have higher shale content than has been encountered in other wells in the area. Despite the likelihood that gas productivity will be undesirably low following stimulation, the industry participants decided to proceed with the stimulation program with the thought that the resulting data would be useful. The success of the stimulation test probably will have to be judged by production increase rather than by production volume.

Jan 1, 1975

By T. E. Sterner

The Bureau of Mines investigated the use of a chromatographic gas analyzer in determining the concentration of combustion products in gas produced during field and laboratory thermal oil-recovery tests. Several parameters (carrier-gas flow, cell current, sample size, and temperature) known to affect quantitative analyses were studied using a commercially available dual-column, dual-detector chromatographic gas analyzer which had been modified to provide close control of these variables. The apparatus made possible a much closer control of air-and gas-injection rates and provided adequate data for performing material-balance calculations and for determining oxygen utilization during the laboratory and field combustion tests. The chromatographic analysis also aided materially in evaluating and measuring bypassing and gas travel times and in detecting high-permeability zones that were present in the reservoir.

Jan 1, 1965