Search Documents

By E. G. King

This publication presents original thermal data for a typical variety of perlite and supplies basic information for use in computing energy requirements in processes for expanding perlite. Perlite has been defined by Raiston 4/ as any silicious lava containing dissolved water in sufficient amount to errand into bubbles when the material is quickly heated to a suitable point in the softening range." The uses of expanded perlite in) the construction and ceramic industries have been discussed by Ralston 4/ and King. 5/ The work described here had a dual purpose: (1) It was desired to ascertain quantitatively, using a typical variety of perlite, just how firmly the contained water is held, and (2) it was desired to obtain basic thermal data sufficient for energy-requirement calculations in processes for expanding perlite.

Jan 1, 1948

By W. M. Mahan

This report describes work carried out by the Federal Bureau of Mines in cooperation with the General Services Administration (GSA). Tests on nickel oxide reduction were conducted at the Pyrometallurgical Laboratory at Pitts-burgh and Bruceton, Pa., and at a rented plant at Canonsburg, Pa. Nickel oxide was reduced to sponge nickel, which was then melted to produce specification-grade nickel ingots containing a minimum of 98.50 percent nickel plus cobalt and a maximum of 1.00 percent cobalt. One purpose of this study was to determine if specification-grade nickel could be made from nickel oxide produced at the United States-Government-owned plant at Nicaro, Cuba, in pilot-plant scale operations involving direct reduction and melting processes. A second and equally important purpose was to obtain cost data on the pilot-plant operation to estimate the cost of producing ingot nickel at an annual rate of 12 million pounds. Laboratory tests verified that nickel oxide, in saggers and in the presence of anthracite fines and dolomite in the ratio of approximately 20:5:1, could be converted to sponge nickel when heated to approximately 1,900° F. for about 2 to 4 hours, depending on the size and density of the oxide charge. The tests also determined the type of saggers suitable for pilot-plant operations.

Jan 1, 1959

By Lindsly. Ben E.

"The recovery or partial recovery of the oil remaining in oil sands after the usual methods of production have become unprofitable is perhaps the greatest problem in the petroleum industry today. The amount of this oil remaining in the sand is variously estimated by those familiar with the subject to be 25 to 90 per cent of the original content.2Lewis3 states, ""The estimate of 80 to 90 per cent of the oil left underground does not seem incredible.""It is estimated by the writer that approximately 91 per cent of the oil originally held in the Elliott pool, was still in the formation on January 1, 1924, and that it would take at least 12 years, at the 1923 rate of production, to further reduce this quantity by one per cent of the original content.The progress made in the oil industry during the past few years relative to the prevention of evaporation losses; to improvement in cracking processes, whereby the gasoline yield from many crudes has been doubled and trebled; to the increased recovery of gasoline from natural gas; and many other developments, remarkable as they are, can be applied only to that comparatively small portion of petroleum products which are raised to the surface. A device or process which would cut development costs to one-half would probably result in a much smaller profit to the oil industry, than the profit derived from an additional 10 per cent recovery of the total amount of oil in a pool. Various methods have been used and many others proposed, for the increase of oil recovery from normally depleted sands.In France, oil sands are being mined by means of shafts and galleries. In other places, notably the Bradford, Pennsylvania field, the yield has been increased by means of water flooding, wherein water is introduced into the sand to displace oil, and drive it to producing wells."

Oct 1, 1926

By Frank J. Weibelt

In accordance with provisions of the Strategic Minerals Act of 1939, the Bureau of Mines surveyed the chromite occurrences in California. The Seiad Creek deposit afforded excellent opportunity for developing reserves that could be used by the nation in case of critical shortages of the mineral. Subsequently an exploration and development program was undertaken in April 1941, which was concluded in October of the same year. Work included road construction, diamond drilling, drifting and crosscutting, surface trenching, and sampling.

Jan 1, 1949

By C. S. Allbright

This report gives the results of analyzing three groups of crude shale oils by the Bureau of Mines procedure:4/ (1) Oils produced by standard Fischer assay determinations on oil shales from Brazil (Paraiba Valley) and the United States (Colorado); (2) oils produced from Brazilian shale by different retorting methods; and (3) oils from high-temperature retorting of Colorado oil shale in the Entrained Solids retort. It is the second in a series presenting data obtained by analyzing crude shale oils from various sources. The series furnishes information on the general characteristics and compositions of a wide variety of shale oils. Use of a standard analytical method on all samples facilitates comparison of different oils. The 18 oil samples analyzed in this project comprised 3 from assays of Brazilian and Colorado oil shales in the Fischer retort, 9 obtained by processing Brazilian shale in various other units, and 6 from entrained solids retorting of Colorado shale at 1,000° to 1,500° F. The crude oils from Brazilian shale contained about half as much nitrogen as the Colorado oils. Properties of the Fischer assay oils from Colorado shales agreed with some data that relate grade of the oil shale with properties of the crude oil from the Fischer assay. Comparison of results from Fischer assays of oils from the foreign and domestic shales shows that the oil from Brazilian shale contains more low-boiling material and less residuum than either of the two from Colorado shale. This fact is reflected in lower specific gravity, viscosity, and carbon-residue values for the Brazilian oil. Retorting Brazilian shale in the Entrained Solids unit at 1,120° F. produced an oil whose boiling range was generally lower than the boiling ranges of oils obtained by processing in three other retorts at conventional temperatures. The quality of crude oils from high-temperature retorting of Colorado shale in the Entrained Solids process varies with retorting temperature. As the temperature is raised within the range 1,000° to 1,500° F., the amount of the naphtha fraction in the crude oil increases to about 35 percent and the aromaticity to 98 percent.

Jan 1, 1956

By Jeffrey Shawn Peterson

The testing procedures of the u.s. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break-flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 2010

By Robert S. Sanford

Intensive investigations of domestic manganese deposits were conducted by the Bureau of Mines and the Geological Survey during the earlier part of the war minerals investigations when there was doubt that the quantity of manganese needed to produce the greatly increased tonnage of steel demanded for war supplies could' to obtained from its customary sources. Domestic deposits of ores that contain sufficient manganese for direct production of ferromanganese essential in steel Manufacture are generally small, and the bulk of the supply is imported. One of the few large deposits of low-grade manganese ore known in the United States is in the Artillery Peale district in southern Mohave County, Ariz. Manganiforous sediments underlie a very large area. Several large groups of claims, covering the most of the manganese-bearing ground, wore assembled in 1929 and 1930. The greater part of this area was leased by the M. A. Hanna Co. in 1937. Investigations by engineers and geologists for this company revealed that the average content of manganese is very low; but that the Maggio Canyon area, about 180 acres, contains higher-grade material. The company put down 28 vertical diamond-drill holds to explore this ground, under the direction of B. N. Wobbor, geologist.

Jan 1, 1948

By F. E. Joyce

The Bureau of Mines studied copper-nickel minerals (mainly sulfides) of the Duluth Gabbro Complex in north-eastern Minnesota to determine their response to selective high-temperature sulfatization techniques. The gabbro, containing 0.44 percent copper and 0.13 percent nickel, was ground to minus 325 mesh and sulfatized in a heated, rotating, stainless steel bench-scale retort. Tests demonstrated that over 95 percent of the copper and 80 percent of the nickel can be converted to water-soluble sulfates, depending upon the roasting conditions employed. Yield equations were developed using regression analysis for predicting the extraction of copper and nickel between the temperature limits of 520° to 670° C, the roasting time limits of 3 to 7 hours, and S02 limits of 10 to 40 percent in S02-air mixtures.

Jan 1, 1971

By C. G. Maier

The present trend of chemicometallurgical research toward widespread and inclusive use of thermodynamic methods requires the inclusion of available data of this sort in any comprehensive metallurgical report . Such data for manganese are far from adequate for the full utilization of these methods . Even if our knowledge of these properties is weak , the collection of available figures is nevertheless well worth while , especially if their utilization in an approximate way may show inherent possibilities of application . No less important is the necessity for discovering the vital gaps in the existing information , to serve as a basis for further pertinent study . The utility of the thermodynamic methods of Lewis and Randall ( 234 ) 3 has become increasingly evident to metallurgists . It is true that at present no better approach to the general , fundamental problems of chemical metallurgy is available than close adherence to these methods . The effort is here made to collect and correlate , as far as possible , significant quantitative thermodynamic data on manganese and its metallurgically important compounds . There are considered here only the intrinsic properties of pure materials . The order maintained as far as possible will be as follows :

May 1, 1934

By Arnold B. Hubbard

This report presents a hydrogenolysis study undertaken to obtain information on the constitution of the kerogen or organic material in Colorado oil shale and to determine some of the properties of the hydrogenolysis products. The high yield of hydrogenolysis products was separated, so far as possible, into type compounds; a number were identified. The results thus obtained were used as a basis for proposing the possible existence of certain structures in kerogen. To the authors' knowledge, few or no hydrogenolysis studies have been made of Colorado oil-shale kerogen by others. However, this method has been used in studying the constitution of coal. In general, the coal studies involved treating pulverized coal at different temperatures and hydrogen pressures with different catalysts. In some instances different solvents were used during the treatments.

Jan 1, 1959

By Wallace W. Roepke

The Bureau of Mines tested new designs of drag bit cutters with sintered diamond inserts instead of standard tungsten carbide tips. The bits were tested for orthogonal cutting forces, primary dust generation, and incendivity, with a standard plumb-bob type conical cutter (600 included tip angle) as the reference. Preliminary wear and impact-failure testing were also done. The results were mixed. Two new designs had forces similar to those of the reference bit, but one new design had about twice the normal force. This same design had almost twice the specific energy during shallow cutting but generated an equal or slightly lower amount of primary dust than did the reference bit. Incendivity was eliminated for two radial designs. One conical design had ignition only after more than 15 impacts, but the other conical design was incendive. Impact failure occurred, but not so quickly as anticipated. Over 7,500 impacts on a sandstone face, with a total cutting distance of more than 1,981.2 m, only scuffed the leading edge of the sintered diamond cutting face but put hairline cracks in the substrate mounting pad. Additional design and testing are needed to develop an optimum cutter, but prospects look good for this material.

Jan 1, 1983

By J. W. Eckerd

This report describes an investigation of the technical feasibility of using a conventional commercial-size (10-ft. i.d.), rotating grate, dry-ash-removal type gas producer to make producer gas from chestnut-size bone anthracite. Test instruments were installed, and some minor changes were made in the equipment to handle the large quantities of materials expected. Extensive tests, lasting about 4 weeks, were planned, using 35 to 50 percent ash chestnut anthracite bone. However, operations were suspended after 8 days when it became apparent that to use this type of fuel satisfactorily substantial changes in equipment and operating procedures would be required. Nevertheless, enough data were obtained to indicate that gas could be produced continuously and routinely from bone coal in this type of producer whenever conditions justified the necessary development work.

Jan 1, 1960

By J. T. Dunham

Zirconium has possible use in industry where severe corrosion conditions are encountered because it resists attack from a variety of corrosive environments. However, very little experimental testing has been done to evaluate the corrosion behavior of zirconium when simultaneously subjected to high tensile stresses and exposed to corrosive environments. This investigation was initiated for an evaluation test, but was limited to environments consisting of ferric chloride solutions which were known to attack zirconium and were shown to promote stress-corrosion cracking in preliminary tests. Tests for cracking susceptibility were conducted by the Bureau of Mines to show the effect of stress, solution concentration, air aeration of solution, and the method of mechanical processing. Tensile stress was applied to the specimens by a constant-load method which proved more reliable than a constant-strain method.

Jan 1, 1961

By R. A. Bloomfield

This report summarizes Bureau of Mines contract research on the disposal of retorted oil shale. A data base has been developed describing the physical-chemical properties, geotechnical engineering properties, and natural cementation characteristics of spent shale. Results of field compaction tests and seepage pond tests are presented, along with results of a partially saturated finite element seepage model used to predict infiltration and seepage rates. Preliminary engineering analyses are presented for underground disposal systems, which include material transport methods, and for a surface disposal system, which includes stability analyses.

Jan 1, 1981

By R. S. Warfield

Following World War II, the rapid increase in both military and civilian activity in the area served by the Alaska Railroad stimulated interest in the availability of local sources of nonmetallic minerals that might be used for building materials. Except for abundant sand and gravel and some pumice, the construction industry of the area depended entirely on high-cost imports for building materials of mineral origin. Because continued rapid growth was anticipated, development and use of local sources of such materials was advocated by both military and civil authorities to reduce the high costs of con¬struction and bolster the unstable economy of the area. The U.S. Department of the Interior began a program On included examining the numerous deposits of nonmetallic minerals accessible to the Alaska Railroad to determine their possible use as raw materials for the construction industry. Preliminary field investigations were made by the Geological Survey. The more promising deposits were subsequently examined and sampled by Bureau of Mines engineers, and the samples were subjected to the laboratory tests necessary to indicate the chemical and physical characteristics of the raw materials or their products. Such field and laboratory investigations were conducted on clay, shale, argillite, limestone, gypsum, and pumice taken from various parts of the area. In initial phasees of the work, done irate 1948 through 1952, many of the deposits examined were suitable for proctoring building materials. Results of the work completed during that period have been published in a Bureau of Mines report3 giving general information and detailed data on more than 35 deposits that were investigated.

Jan 1, 1962

By G. W. Weems

The specific objective of this investigation was to determine the compressibility factors for helium and carbon dioxide mixtures at -10° and -20° C and pressures to 1,000 psia. A Burnett apparatus was used. Data from the experiments were treated by the method of Barieau and Dalton. Tables of compressibility factors and approximations of the virial coefficients are presented for 10 binary mixtures as well as for helium and carbon dioxide. The results follow the same trend as data previously reported.

Jan 1, 1970

By D. A. Douglass

This report describes the tri-n-butyl phosphate extraction of cerium (IV) from a sulfate leach liquor prepared from a bastnaesite concentrate as well as from pure eerie nitrate solutions. The work was done on a laboratory scale using separatory funnels. Extraction from pure cerium solutions entailed no great difficulties; however, extraction from the bastnaesite solution proved more difficult, mainly because of the inhibiting effect of the sulfate ion. Despite this, procedures were developed for obtaining good single-state cerium extraction (95+ percent) and a high-purity product (99+ percent), although the maximization of both cannot be achieved simultaneously. This necessitates a compromise in any extraction scheme.

Jan 1, 1959

By Grace N. Broderick

U.S. supply and demand data for coal, by States and regions, were tabulated for the years 1960 and 1965. Estimates are provided of State-by-State quantitative data for the coal industry that can be integrated into State and regional energy balances by source, form, and consumer sectors, and used for estimates of interstate and interregional energy flows. The tables give an estimated total supply of coal available for consumption, and also report the distribution of the supply among the major consuming sectors (household and, commercial, industrial, transportation, and electricity generation). To enable comparison of coal data with those for other energy forms, tonnages were converted to British thermal units (Btu). Future energy analysis studies could be facilitated by changes in the categorization of information collected on the coal industry. The data shown are based primarily on Bureau of Mines source material.

Jan 1, 1969

By Robert M. Becker

Part 5, the last of this series, deals with the theoretical confirmation and application of results developed in parts 1 and 2. The bulk-sampling variances of Hassialis and Kassel and Guy are compared with those in part 2, both as to formulation and as applied to ores and coal. The results provide confirmation for much of the development in part 2. Examples are presented for determining the reliability of bulk samples with respect to various measurable characteristics. These characteristics include, for example, assays for elements or compounds and particle surface area. The bulk samples considered consist either of a given weight, a given volume, or a given number of particles. In addition to problems of sample reliability, some of these examples may also be applicable to quality control. Several possible applications of results developed in parts 1 and 2 are outlined. These include tests for random data, degree-of-mixing indices, and particle-fineness indices.

Jan 1, 1966

By W. S. Sanner

Seven samples were analyzed from the major reserves of the Bottom Red Ash bed, Northern anthracite field. The data show variations in thickness and geo-logic structure and in the amount of coal that can be recovered. Recovery of market-grade (less than 17 percent ash) coal is high for all samples, ranging from 76 tp 95 percent in the 3-1/4-by 9/16-inch sizes. The occurrence of coal containing less than 5 percent ash varies from 19.5 to as much as 57.5 percent. Crushing the coarse sizes to minus 9/16 inch increased recovery of market-grade coal in six of seven bed samples. Crushing released sufficient impurities to cause substantial increases in yield of coal containing less than 5 percent ash for all samples. Analyses of the float coal indicate that the quality of coal is comparable for all samples.

Jan 1, 1967