Search Documents

By A. W. Deurbrouck

The Bureau of Mines reviewed available data on the effect of crushing high-sulfur coals for the liberation of impurities in the light of increasingly stringent air pollution regulations. The survey, which provided information on Appalachian region coals only, indicated that such important coal-beds as the Upper and Lower Freeport and the Upper Kittanning show significant sulfur reductions when crushed to 14-mesh top size. For many other coalbeds amenability to sulfur liberation by crushing was indicated, although too few samples were available to draw firm conclusions,

Jan 1, 1966

By G. W. Birge, D. E. Wolfson, J. G. Walters

An investigation was conducted to determine the relationship between ASTM and Micum tumbler data and to develop equations that would enable the conversion of data from one test method for comparison with those determined by the other , and thereby facilitate the international exchange of data . Relative strengths of 18 commercially produced cokes were determined by ASTM and Micum tumblers and ASTM shatter test . Two of the samples were coke produced for foundry use , and two were produced in beehive ovens . The remaining 14 samples were produced for blast furnace consumption and had ASTM tumbler stabilities of 36 to 58. Statistical procedures were used to relate the three test methods and also to evaluate the effect of charge weights , top sizes of coke , and types of screens specified by the two standard tumbler procedures , square - hole wire mesh for the ASTM tumbler and punched round - hole for the Micum . A significant result was that the data obtained with like screens have a higher degree of correlation with a smaller standard deviation than data from the screens specified for each tumbler .

Jan 1, 1964

By Murray Weintraub

In an investigation of the incineration of combustible wastes, the Bureau of Mines studied the effect of dimensional parameters, process variables, and fuel properties on the operation of an incinerator that consisted of a single cylindrical combustion chamber in which all combustion air was supplied tangentially above the fuel. Construction and operation of three designs of such a device proved that the tangential overfire air design is effective in providing efficient combustion and low concentration of particulate matter in the effluent gas. A correlation was found that related burning rate with air rate, chamber diameter, and inlet port diameter. In one of the incinerator models, ignition was by radiation from a preheated surface. The temperature of this surface was required to be 1,400° to 1,600° F to insure ignition of moist refuse; however, this had little effect on combustion rates. In the combustion of moist refuse, evaporation of the water proceeded through the fuel bed as a wave, with an ignition wave following the evaporation.

Jan 1, 1967

By David J. Kusler

A gravimetric method for the determination of carbon dioxide, carbon monoxide, hydrogen, methane, and oxygen in blast furnace top gas is described. Nitrogen may be determined directly by volume measurement or by difference. The method is direct, permits continuous as sampling, and provides an averaged analysis over a selected range of sampling intervals from 1/2 to 24 hr or more. Neither expensive equipment nor specialized personnel are required. The method is suitable for routine analysis, and the results compare favorably with those obtained by established methods.

Jan 1, 1963

By M. A. Elliott, F. W. Brown

"INTRODUCTION During the recent war the Bureau of Mines, at the request of one of the armed services, investigated the hazards that night be encountered 5n handling perchloric acid, particularly if spilled on certain materials. The hazardous nature of perchloric acid when mixed with reducing agents had been known qualitatively, but it was desired to obtain quantitative data on the explosion hazards of such materials. Accordingly, tests were made to determine the sensitivity of mixtures of perchloric acid and oxidizable materials to initiation by heat, impact, sparks, flame, and explosive impulses. This report summarizes the results of those tests.PROPERTIES OF PERCELORIC ACIDAnhydrous perchloric acid is a colorless,hygroscopic, volatile, mobile liquid that fumes in the air. The anhydrous acid is unstable at ordinary temperatures, and therefore the commercial acid is a water solution containing either 60 percent or 70 percent by weight of the anhydrous acid. The commercial acid is widely used in chemical analysis, frequently to oxidize organic material. If proper precautions are not observed, such an oxidixation may become exceedingly rapid and result in an explosion. Several such explosions involving the acid are mentioned in the literature. 4, 5, 6/"

Jan 1, 1948

By R. E. Heithecker

Zwolle oil field of Sabine Parish, La., is different from most oil producing areas of the State in that the oil is obtained from marl and chalk-rock formations. The thickness of the reservoir rocks averages 500 feet; but production is not continuous throughout this thickness, as the oil apparently is localized in vertical and nearly vertical solution cavities and channelways or in porous zones of limited horizontal extent. The nature of the oil accumulation has caused two outstanding peculiarities of the field: (1) About 60 percent of the tests drilled were dry holes and (2) there were many instances of well interference. Commercial production was discovered in November 1928, after 17 years of prospecting in and around the present limits of the area now developed which has a length of about 22 miles and a maximum width of 4 miles. The field had produced 10,266,896 barrels of oil to January 1, 1934. The oil ranges in gravity from 400 to 420 A.P.I. Although the field is divided into several districts which are more or less clearly defined and separated by unproved territory the term Zwolle field", as used in this report, includes the entire area from Blue Lake on the west side, through Zwolle proper, and eastward, including the Many or Eastern extension.

Jan 1, 1934

By L. L. Oden

The purpose of this research was to develop a method to remove copper and tin from the magnetic fraction of incinerated municipal refuse, as recovered by the Bureau of Mines pilot plant in College Park, Md. Copper, present in the scrap in a metallic form bonded to ferrous objects, was amenable to leaching in cupric ammonium carbonate solution. Copper levels in small 5-to 10-lb lots of treated scrap were reduced from the initial level, 0.5 to 0.6 pct, to 0.1 to 0.2 pct. Larger lots of scrap (100 lb) were treated less effectively because of poor contact of solution and scrap. Oxidation in the air or in aerated aqueous solution was applied to liberate tin from the dilute solid solution present on the surface of incinerated tinplate. Shredding of air-oxidized scrap or caustic leaching of scrap oxidized in solution reduced tin levels from the initial 0.25-pct level to about 0.1 pct.

Jan 1, 1973

By A. T. Coumbe

The first survey 3/ covering sales of liquefied petroleum gases was made in 1930 by the Bureau of Mines, which at the time was under the United States Department of Commerce. This original canvass covered national totals for 1922 through 1929, and most of the supply came from natural gasoline plants. The 1930 report showed approximate totals for butane and propane and for butane-propane mixtures and pentane grouped together. No attempt was made to breakdown the national sales by various uses until 1931, when the quantities for domestic or household consumption, gas manufacturing, and industrial requirements, including miscellaneous uses were indicated. As the market for these liquid petroleum gases expanded and as new uses came into importance, their respective quantities were shown separately in the annual survey. Sales for internal-combustion engine fuel and for raw material for chemical plants were first taken out of the industrial total in 1936. During World War II liquefied petroleum gases became important as feed stock diverted to synthetic rubber plants, and consequently the survey was broadened to cover this particular demand, beginning in 1944. Pentane was dropped from the survey after 1943, as, being liquid at atmospheric pressure, it is not considered as one of the liquefied petroleum gases and furthermore, the quantity reported made up less than 1 percent of the total sales. Thirteen producing companies reported to the Bureau in the first survey made in 1930, and in the 1952 canvass about 130 producers--petroleum refiners and natural gasoline companies--and about 1,300 dealers cooperated by filing schedules showing a breakdown of their sales. Their 1952 deliveries of approximately 4.5 billion gallons of liquefied petroleum gases were equivalent to about 3.4 billion gallons of gasoline or 3.1 billion gallons of distillate fuel oil.

Jan 1, 1954

By J. W. Town

Studies were made by the Bureau of Mines to determine the influence of textural features on the beneficiation of phosphate minerals (pellets) from selected bed and composite samples representing different rock types of the Western Phosphoria Formation. The particle size of the samples was reduced by attrition grinding to minus 20-, 28-, or 48-mesh depending on ore grade and gangue matrix. Sizing of the ground material showed that the phosphate pellets would concentrate in the plus 200-, 270-, or 325-mesh size fractions sufficiently so that the phosphate content was above the 31.5 :cent P2O5 required for acidulation. The phosphate content of essentially pure phosphate pellets was shown to range from 33 to 39 percent P2O5. Microscopic identification of the particles in each size fraction showed that the phosphate was either in the pellet form and readily liberated or so intimately associated with the gangue matrix that size reduction necessary Co obtain liberation was impractical.

Jan 1, 1967

By D. J. MacDonald

The Bureau of Mines has conducted bench-scale investigations leading to the design of an integrated process for producing reactor-grade zir-conium oxide (Zr02) from zircon sand, which avoids the air pollution, water pollution, fire hazard, and odor problems associated with the hexone-thiocyanate process. The integrated process consists of three steps: production of crude zirconyl sulfate solution, solvent extraction, and production of Zr02 from strip liquor. This report describes the solvent extraction step. Multistage, countercurrent liquid-liquid extraction with a tertiary amine in kerosine was used to separate zirconium from a dilute H2S04 solution containing hafnium and other impurities. Process steps de-scribed include extraction from an aqueous feed solution to form a hafnium-contaminated, zirconium-bearing organic-phase solution, scrubbing to separate zirconium from coextracted hafnium, stripping to transfer hafnium-free zirconium into an aqueous strip liquor, chloride-loading to produce a chloride-bearing organic solution, scrubbing with the chloride-loaded organic solution to remove traces of uranium impur-ity from the zirconium-bearing strip liquor, and regeneration to pre-pare the organic solution for reuse. These steps were performed simul-taneously in steady-state, bench-scale experiments. Zirconium recovery of up to 93 pct was achieved. Results of an economic evaluation are included.

Jan 1, 1984

By J. M. Riley

The Bureau of Mines investigated a promising new technology for recovering A1203 from alunite to support the Bureau's alumina miniplant project. Results are presented for a study of the technical feasibility of treating alunite crushing and grinding reject fines for recovery of A1203. Alunite pellets having sufficient strength and resistance to degradation were produced by combining fines and coarse alunite with a KOH binder. The best pellets were prepared, in a laboratory pelletizer, by adding 1 pct KOH as a 5-pct solution to a mixture of 40 pct alunite dust (98 pct minus 65 mesh) and 60 pct coarse alunite (minus 20 plus 65 mesh). Calcines suitable for K2SO4 and A1203 recovery were produced by reducing dehydrated alunite pellets with sulfur in a laboratory shaft furnace for 4 h at 600° C, followed by air oxidation of the reduced calcine for 1 h at 600° C. This report presents design calculations, schematic diagrams, and discussions of the essential features of a proposed process research unit (PRU)--a continuous, 6-lb/h alunite shaft furnace--for studying the process.

Jan 1, 1983

Possible consequences of continuing internal political unrest and the imposition of foreign sanctions raise concerns about the traditional reliability of the Republic of South Africa as a major world supplier of important minerals. A recent Bureau of Mines' technical report (Open File Report 76-86) examined the impacts of temporary peacetime disruption scenarios for six key materials and mitigating options. Because of South Africa's dominant producer position for these minerals (except for cobalt), expansion of primary production capacity outside of South Africa is not a short term mitigative option. However, prospects of a longer term disruption would likely spur investment in capacity expansion in alternative Market Economy Country supply sources. This report identifies the resources, production costs, and burdens that would be placed on alternative MEC producers of chromium, cobalt, gold, manganese, and platinum-group minerals if South Africa's production were subject to a long term; disruption. When long term supplies from South African deposits are discounted, more than a few years reserves were found only for cobalt and manganese. Even for these two minerals, higher sustained prices would be required to increase manganese production capacity and to support means of cobalt transportation not through South Africa.

Jan 1, 1986

By Paul R. Thomas

The Bureau of Mines evaluated the impact of the depletion allowance upon the economic availability of copper from domestic deposits. The potential long-run percentage depletion deduction, cumulated over the life of the properties, was estimated at approximately $2.5 billion for producing properties and up to $11.7 billion for nonproducers. The income transfer, in the form of higher Federal income tax payments if the allowance were repealed, was estimated at $1.5 billion for producing properties and up to $8 billion for nonproducers. The percentage depletion allowance, through its role in determining Federal income tax liability, was found to be very significant in affecting profitability. Repeal of the allowance could result in major domestic copper availability reductions at all price levels, now and in the future, as a result of reduced profit margins for current producers, and postponement of development decisions for nonproducers. It was demonstrated that a 50-percent reduction in the percentage depletion rate applicable to copper would also result in a significant decrease in profitability for nonproducing properties. For producing properties, the percentage depletion rate on copper was shown to be less significant than the income limitation that is placed upon the total amount of the depletion deduction. Repeal of the minimum Federal tax provision was shown to be significant in enhancing profitability for both producing and nonproducing deposits. The report concludes that the percentage depletion allowance operates as an important method of capital recovery and production incentive.

Jan 1, 1982

By Leonard Obert

The investigation reported herein is concerned with the generation and propagation of the strain wave produced in rock by the detonation of a high-velocity explosive. This report is the second of a series that will deal with this and related problems. The rock type in which these experiments were carried out was greenstone. Subsequent reports will discuss similar investigations in other rock types. Specifically, the problem under study is concerned with how certain characteristics of the strain wave, such as the maximum compressive and tensile strain, the maximum time rate of change of strain, the frequency components present in the pulse, the duration of the pulse, and other measurable characteristics, vary with the size of the charge and the distance from the detonation point to the point of measurement. . Other investigators have studied certain aspects of the generation and propagation problem in rock. However, in these studies the travel distances from the detonation to measurement point were comparatively long and the frequency components in the explosive wave were usually under 100 c.p.s. In this study the detonation to measurement distance covered. the range from 2 to 54 feet, and the strain gages and recording equipment employed in the instrumentation of the problem had a frequency response range from 200 to 10,000 c.p.s.

Jan 1, 1950

By Robert F. Pettit

This paper on methods and costs of mining and milling iron ore at the Iron Mountain mine of Ozark Ore Co., St, Francois County, Mo., is one of a series of Bureau of Mines reports on methods, practices, and costs of mining and milling throughout the United States. The Iron Mountain operation is notable for its successful transition from open-pit to underground mining, for use underground of large earth-moving equipment, and for development of a multilevel room-and-pillar mining method. Milling methods also have undergone transitions - from hand sorting and log washing in the early days to gravity concentration. Milling ultimately may include flotation to recover additional iron from products now discarded as tailing,

Jan 1, 1957

By Thomas M. Nasiatka

This report briefly describes the present state of the art and the technological highlights of tunneling from its inception to the present. The discussion is concerned primarily with tunnels driven through relatively competent rock for mine development and various civil purposes. In addition to pinpointing the major technological breakthroughs in tunneling, this report indicates their general effect on the speed of tunneling. The tunneling speeds are based upon data from approximately 80 tunnels listed in the appendix. These data include length; cross section shape and dimension; type of rock; tunneling method; method of breaking, loading, and transporting the rock; average linear progress rate; and cost in values during the period of construction. Most of the tunnels described have diameters of 15 to 30 feet.

Jan 1, 1968

By Z. T. Bieniawski, R. K. Zipf

"Zipf Jr., R.K. and Bieniawski; Z.T., 1989. A fundamental study of respirable dust generation in coal. Min. Sci. Technol., 9: 87-99Black lung disease in coal miners induced by the formation of fine fragments of coal imposes very high human and direct costs. A fundamental understanding of the fracture processes leading to fine-fragment formation in coal by applying principles of fracture mechanics is presented. A four-step hypothesis is proposed which sequentially describes the mechanics of fine-fragment formation during a generic coal material—coal cutting tool interaction. These steps include: (1) development of a crush zone under the tool tip, (2) macrocrack propagation. (3) shear movement along macrocracks, and (4) additional fragmentation from shear. This model contains two sources of fine fragments, namely crushing under the tool tip and shearing along the macrocrack surfaces. Three critical assumptions are made that require experimentation. First, the coal material must contain flaws of sufficient density and sufficiently small size to liberate fine fragments by crushing. The following conceptual relationships are proposed between flaw size, spacing and fragmentation: first, the active flaw size must be less than the desired particle size and second, the spacing (or density) must be in the order of the particle size. The second major assumption is that a mixed mode fracture theory will describe the initiation and crack growth direction for the microscopic inherent flaws. The third assumption is that some degree of roughness damage, and interlocking exist along the newly formed macrocrack surfaces such that a small amount of shear movement along that surface leads to additional particle formation at a microscopic scale. Preliminary analysis of the mechanical regime under a cutting tool tip places order of magnitude bounds on the stresses strains, cycle time, stress rates and strain rates. Even though the tool moves and loads the coal material with considerable speed, a quasi-static stress analysis is applicable in this region.Introduction.The generation of fine fragments (respirable dust) during various coal mining processes may lead to the incidence of coal workers pneumoconiosis (black lung disease). The human and direct cost of dust-induced illnesses in coal miners is very large. By several. accounts [1,2] the Federal Government paid out about $12 billion to almost 500,000 coal miners and their beneficiaries between 1970 and 1980. In addition, several states and many coal operators have established their own compensation programs at costs ranging from a few cents to several dollars per ton of coal mined [2]. Since 1980, 'the present liability of the Federal disability trust fund has approached $20 billion and the benefit payments exceed $1 billion per year. There .are also hidden costs due to dust, in the form of increased equipment wear and decreased operator productivity, both of which are due to the poor operating environment. Quantifying these costs may be difficult; however, they may be in the same range as the present pneumoconiosis costs. These high human and direct dollar costs may be prevented or reduced through long term research efforts directed at understanding the generation and control of respirable dust and the incidence of black lung disease."

Jan 1, 1989

By R. Barany

The heats of formation of seven substances were determined by solution calorimetry. At 298.15° K, the heat of formation of lithium sulfate from lithium, rhombic sulfur, and oxygen was -343.1 ± 0.7 kcal/mole, and the heat of formation of lithium sulfate monohydrate from lithium, rhombic sulfur, oxy-gen, and hydrogen was -414.3 ± 0.7 kcal/mo1e. For the silicates, the heats of formation at 298.15° K from the elements were kaliophilite, -503.8 ± 0.5 kcal/mole; leucite, -721.6 ± 0,8 kcal/mole; eucryptite, -505,2 ± 0.6 kcal/mole; alpha-spodumene, -727.9 ± 0.9 kcal/mole; and beta-spodumene, -721.1 ± 0.9 kcal/mole. The corresponding heats of formation at 298.15° K from the constituent oxides were kaliophilite, -42.7 ± 1.1 kca1/mole; leucite, -42.8 ± 1.1 kcal/mole; eucryptite, -16.1 ± 0.7 kcal/mole; alpha-spodumene, -21.0 ± 0.7 kcal/mo1e; and beta-spodumene, -14.3 ± 0.7 kcal/mo1e.

Jan 1, 1966

By M. Hayashi

The Bureau of Mines conducted laboratory studies on Idaho mudstones to examine techniques for extracting vanadium. Recovery of vanadium from low-grade sources could contribute to future vanadium production and reduce reliance on imports. An Idaho mudstone surface sample containing 0.30 pct V205 and an underground sample containing 0.21 pct V205 were used in the extraction tests. Leaching of the surface sample for 18 h at 800 C with the addition of up to 1,000 lb/ton H2S04 recovered 70 pct of the vanadium. How-ever, leaching of the underground sample under the same conditions re-covered only 47 pct. By adding 15 wt pct NaCl and roasting the samples at 7500 C for 2 h, followed by leaching with 800 lb/ton H2S04, vanadium extractions were increased to 78 pct from the surface sample and 83 pct from the underground sample. Water leaching of samples roasted at 7500 C for 4 h with a 25-wt-pct NaCI addition yielded about 60 pct of the vanadium from both surface and underground samples. Autoclave leaching at 2000 C for 3 h with 1,000 Ib/ton H2S04 extracted 97 pct of the vanadium from the surface sample and 86 pct from the underground sample. An exploratory solvent extraction investigation to purify and concentrate vanadium in the leach solution using several organic reagents was also conducted.

Jan 1, 1985

By M. R. Geer

The widespread adoption during the past decade of the dense-medium process for cleaning coal increases the need for technologic studies of the process. Such studies provide information that will insure maximum usefulness of this process in its present form and may well lead to substantial improvements in design and opera¬tion. The Bureau of Mines has published the results of cleaning trials on a wide variety of coals in two dense-medium pilot plants5/ and reported the recovery of coal from waste by dense-medium treatment.6./ The present report deals with the viscosity of magnetite dense medium, an important subject about which virtually nothing has been published. Specifically, the report concerns methods for measuring viscosity, the influence of various medium contaminants on viscosity, the effect of viscosity on cleaning results, and the influence of viscosity on consumption of medium. Cleaning trials on four coals of varied density composition in a pilot plant, using mediums of different viscosities, showed a steady reduction in cleaning efficiency with increasing viscosity in every instance. However, the behavior of each coal in a viscous medium was distinctly individual. With one, an increase of only 1 centipoise in viscosity caused a reduction in recovery efficiency of 7.7 percent, whereas the same increase in viscosity with another reduced recovery efficiency only 2.7 percent.

Jan 1, 1957