Search Documents

By BUREAU OF MINES

PLATINUM

Feb 1, 1922

By Paul Hatmaker

Pumice and pumicite are siliceous volcanic substances quite similar in chemical composition , but somewhat different in physical properties , manner of formation , and mode of occurrence . Production in the United States has increased from 23,271 tons valued at $ 94,943 in 1910 , to 56,843 tons valued at $336,099 in 1930. Both pumice and pumicite are included in these figures as it has been impractical to collect statistical data on the separate commodities .

Mar 1, 1932

By A. B. Hooker

Gassy mines require daily inspections with methane detectors to test for the presence of methane. Although in many manes it may be sufficient to know that there is no methane present or that its percentage is below a certain amount, it is desirable and often necessary to determine definitely the percentage of methane at the working faces and in the various air currents. The Bureau of Mines recognizes two general types of portable methane detectors, namely; 1. Methane detectors by which the presence of methane may be detected and its approximate percentage estimated.

Jan 1, 1929

High resolution seismic refraction tomography has proved to be a useful tool to effectively estimate depth of blast induced damage in a mine face. Excavation blast damage can be as shallow as 1 to 2m and requires resolution at a fraction of a meter for effective imaging. We used an accelerometer with flat frequency response to 1000Hz to record data at spacings of approximately 0.25 to 0.5m along mine walls. First arrival times from the seismic data were used to produce P-wave velocity tomograms. The tomograms show transition from low velocity zones to velocity associated with competent rock. We interpret the low velocity zones to indicate residual fracturing from blasting. Experiments on a concrete test block and at two underground mine locations give results that are consistent with fractured rock transitioning to competent rock. Our method can be applied efficiently in an underground environment to provide continuous velocity information with depth into a mine wall over a span of approximately 10m.

Jan 1, 2009

By E. C. Lane

During the past 15 years the Bureau of Mines has made and published several hundred analyses of typical petroleums and has developed a system of interpreting the analyses and of classifying crude oils. In describing crude petroleum frequent reference is made to the "base" of the oil, a usage the petroleum industry has found convenient. As part of its general study of the characteristics of crude oils, therefore, the Bureau of Mines has developed a system of classifying them according to "base." This system as first published in 19274 was limited to four classes and in its original form is no longer considered adequate. Since the system was first published the Bureau has analyzed a large number of crude oil-, including representative samples from nearly every important producing field in the world, and has found that the system of classification could be revised and amplified to advantage. The revised system is presented herein. Bulletin 2916 states that many oil producers and refiners use the word "base" much as it is used in pharmaceutical work. For example, the "base" or "basis" of an ointment or salve is the fatty material (lard, petroleum, or lanolin) used as a vehicle or carrier for the active medicinal principles. Apparently many of the pioneers in the petroleum industry considered crude oil similar in nature to these medicinal products in that it consists of a semisolid, nonvolatile base and 1 volatile portion can be distilled off to make gasoline, kerosene, and other products. Many crude oils when chilled slowly deposit a waxy material (paraffin); this fact may have been one reason for the use of the term "paraffin base" in referring to such oils. Almost all of the petroleum first discovered in the United States was of this nature; not until the oil industry was extended to California and along the Gulf coast was petroleum found that contained no wax but apparently did contain asphaltic material Accordingly, these oils were known as "asphalt-base" oils. The use of this term, however, seems unfortunate, as better-grade oils of this type contain little if any asphalt; the descriptive term "naphthene base" now seems to be a more desirable term than "asphalt base." The term "intermediate base" is also used commonly in referring to oils intermediate in oharacteristios between those of paraffin and naphthene base.

Jan 1, 1935

By W. I. Garms

This paper, describing the milling practices at the Hayden concentrator of the Nevada Consolidated Copper Co. is the first of a Series being prepared by the Bureau of Mines on milling methods and costs in various districts of the United States. The Hayden concentrator is located at Hayden, Gila County, Ariz., 20 miles from the mine at Ray, Pinal County, Ariz., and approximately 1-1/2 miles north of the junction of the Gila and San Pedro Rivers. During the fourth quarter of 1928 the concentrator treated daily by flotation an average of 10,336 tons of ore containing 1.25 per cent of copper. The average recovery during this period amounted to 87.84 per cent of the total copper. The concentrates contained 19.88 per cent of copper.

Jan 1, 1930

By M. P. Ahola

This U.S. Bureau of Mines report presents an overview of the use of three unique numerical modeling methods to analyze cutter roof problems in underground coal mines. Cutter roof failures are common in coal mines where the immediate roof is comprised of thin laminae exposed to highly biaxial tectonic stress fields. The predominant mechanism for failure is assumed to be excessive shear stress at the entry corners exceeding the shear strength of the rock. Early work in this area utilized the finite-element method and then the boundary-element method to analyze several cutter roof control measures. Various stress control measures were simulated to estimate their respective effects on reducing the high levels of shear stress at the entry corners. More recent studies made use of the discrete-element method. This method was used to take the analyses beyond the elastic continuum limits to simulate the propagation of a shear fracture and subsequent redistribution of stress within the mine roof. A simple roof bolt model was implemented to show the benefits of bolting to increase the resistance to shearing and separation along horizontal bedding planes and maintain roof stability.

Jan 1, 1991

By O. M. Bishop

"INTRODUCTION Early in World War II, the Bureau of Mines realized that reserves of fluorspar ore at many mines in the southern Illinois fluorspar district were not being developed as rapidly as the old ones were being depleted. At some mines the measured and indicated ore reserves were almost entirely depleted, although geologic factors favored new discoveries. The Leo mine, which had not been worked since 1938, was among this group of mining. The Bureau of Mines, together with the Illinois Geological Survey examined the property, studied the mine records and,geologic factors in 1944, and agreed that exploratory drilling was warranted Funds were,obtained for the work in the fiscal year 1945, and drilling was done; between October 27, 1944, and June 15, 1945.The property was owned in fee simple by the Hllside Fluor Spar Mines at the time exploration was begun in October 1944. Subsequently, in 1945, the Inland Steel Co. acquired of the Hillside property."

Jan 1, 1947

By Charles W. Huggins

To determine the nahcolite and dawsonite content in oil shales, the Bureau of Mines compared X-ray diffraction, infrared spectroscopy, thermal methods, and a previously published method by Smith and Young based on the selective solubility of sodium compounds. The Smith and Young method and a new method based on the weight of carbon dioxide produced by thermal decomposition are recommended for determining nahcolite. X-ray diffraction and the Smith and Young method are recommended for determining dawsonite. X-ray diffraction, infrared spectroscopy, and differential thermal analysis were useful for identifying other minerals in the samples.

Jan 1, 1973

In 2005, a total of 263 metal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Metal mines were the smallest mining commodity sector, comprising 1.8% of all mining operations. ? Gold mines comprised 46.0% (n=121) of all metal mining operations. Other common types of metal mines were iron ore (n=32; 12.2%), copper ore (n=31; 11.8%), and lead and/or zinc ore (n=16; 6.1%). ? Nevada had the largest number of metal mines (n=52; 19.8%), followed by Alaska (n=27; 10.3%).

Jan 1, 2008

By Richard A. Allwes

The Bureau of Mines conducted an in-mine case study on two consecutive three-entry gate road systems designed in accordance with the stiff-yield pillar design concept. This Bureau study was conducted in order to further develop technology that will improve the health and safety aspects of longwall mining. Support loading and strata activity were monitored to determine the effects of retreat longwall mining on the gate road ground control system. Analyses of pillar stress and roof bolt loading histories revealed that headgate roof support elements ex-perienced cumulative loading throughout the life of the longwall panel. Tailgate pillar loadings had significantly different histories from the loading histories of the headgate pillars. Stress relief occurred in the tailgate pillars following the passage of the longwall face. More-over, the stiff-yield pillar design, with the abutment pillar placed adjacent to the working panel when part of the headgate system, provided effective ground control in that no major roof falls or roof problems were experienced in the headgate or tailgate systems during longwall mining.

Jan 1, 1985

By Larry L. Anderson

Enormous quantities of organic wastes are produced each year in the United States. The total amount is in excess of 2 billion tons and at least 880 million tons of this is moisture- and ash-free organic material (dry organic solids), representing a potential energy source of significant magnitude that is not being utilized. Bureau of Mines scientists have developed methods for converting these wastes to convenient energy forms. This report itemizes and evaluates for the first time in detail the quantities and sources of moisture- and ash-free organic material contained in manure, urban refuse, industrial wastes, sewage solids, and agricultural wastes in the United States. Furthermore, estimates are presented for amounts of organic wastes collected or concentrated. The potential for fuel, either oil or gas, from both the total organic wastes generated and those collected or concentrated is also estimated.

Jan 1, 1972

By Robert H. Merrill

This report summarizes the first phase of studies to determine the design and behavior of an unsupported roof in an experimental room in limestone. The selection of a roof horizon and the design of the room were results of an investigation of the geology of the formation, the physical properties of samples from the proposed roof, and calculations from the theory of gravity-loaded beams. The design of the opening, some physical properties of the roof in place, and the behavior of the roof were checked by tests in a full-scale experimental room. The room was instrumented to measure roof deflection, separations in the roof strata, and incipient failure. The dimensions of the room before instrumentation was installed were 10 by 100 feet; the room was widened in successive increments to 40 by 100 feet. Between widening operations periods up to 6 months were allowed to provide a time test of the roof spans. The results of the measurements of deflection and separations showed that the lowest 6-inch layer in the roof became detached as the room was widened. This layer was eventually removed after standing without failure for about 4 months at room dimensions of 40 by 100 feet.

Jan 1, 1957

By Richard A. Dick

Eight blasts were fired in a 2-1/2-ft bench in the Stewartville member of the Galena Limestone formation in an aggregate quarry near Stewartville, Minn. The shots were dimensionally proportional to production-size bench blasts and were about 5 to 10 percent of full scale. The effects of site, timing of initiation, and burden-to-spacing ratio were studied in a 2 x 2 x 2 factorial experiment, using three boreholes, caw;, containing a 1/2-in charge diameter of high-density ammonia dynamite, in each blast. Detonation velocity measurements indicated that the dynamite detonated satisfactorily in the 1/2-in charge diameter. The effects of the three experimental variables were analyzed by weight for the percentage of oversized material produced and for size distributions determined by screening the entire muckpiles. The bench faces were painted before each shot in an effort to determine the origin of the oversized material. The square pattern (burden and spacing = 15 in) produced finer overall fragmentation and less oversized material than the rectangular pattern (burden = 15 in; spacing = 22-1/2 in). Sites 1 and 2 were about ft apart. Although site 2 produced slightly better overall fragmentation than site 1, the amounts of oversized material produced showed no significant difference. The timing of initiation (instantaneous or delayed) did not significantly influence the overall fragmentation or the amount of oversized material produced.

Jan 1, 1973

By Raja V. Rarnani, Robert L. Frantz

"Mining is one of the oldest of human occupations. The awareness of occupational illnesses associated with mining, even in ancient times, is evident from the writings of Hippocrates (460-370 BC), Pliny and Elder (AD 23-79), and Galen (AD 131-210). Georgius Agricola (1494-1535), in his De Re Metallica, refers to the diseases of miners and the need for their control through good planning and operating practices and responsible management (Schwerha, 1989). Coal workers' pneumoconiosis (CWP), often called Black Lung disease, is an occupational disease which results from inhalation of coal mine dust which usually contains relatively small amounts of free crystalline silica.A pneumoconiosis is best defined as the accumulation of dust in the lungs and the tissue's reaction to its presence [Lapp and Castranova, 1993]. Silicosis is the name given to the fibrotic disease of the lungs caused by the inhalation of dust containing silicon dioxide, primarily in the free crystalline form. Silicosis is the older and more well known of these mineral pneumoconioses. In contrast, CWP was not recognized as different from silicosis until the pivotal work of Collis and Gilchrist [1928].The U.S. Bureau of Mines (USBM) still regards worker exposure to respirable aerosols in mines as the most serious health problem in mining [USBM, 1994]. The National Institute of Occupational Safety and Health (NIOSH) is considering recommending a reduction in the standard for occupational exposure to respirable coal mine dust from 2 mg/m3 to 1 mg/m3 [NIOSH, 1993]. The Mine Safety and Health Administration (MSHA) may require new criterion for sampling procedures in the mine that would evaluate the ambient dust concentration in the mine atmosphere based on a single sample, instead of the current practice of averaging five samples (MSHA, 1992; Ramat* 1993). Several high-production longwall mining faces currently have extreme difficulty meeting the existing dust standards, and some already operate at reduced production levels to achieve mandated levels [USBM, 1993]. The importance of adequately protecting the miners from high concentrations of coal mine dust, as well as of reducing the incidence and severity of the Black Lung disease, cannot be overemphasized. The importance stems, first and foremost, from the humanitarian viewpoint and, second, from the perspective of the overall welfare of the coal industry.The histopathologic hallmark of CWP is the coal macule (Balaan, Weber and Banks, 1993). Autopsy or open lung biopsy reveals the coal macule to be an amorphous mass of coal particles, dust-laden pulmonary macrophages, reticulin, and collagen. No pathognomonic signs or symptoms identify workers with CWP. A CWP diagnosis requires that the worker experienced the appropriate dust-exposure setting (e.g., underground coal mining) and duration (usually 10 years or more) and, has the characteristic chest radiograph. Based upon the International Labour Organization (ILO, 1980) international classification, pathologists and radiologists have established case definitions for characterizing the pathology and the appearance of CWP on chest radiography (Weeks, 1993). CWP appears in two principal forms: simple, with small opacities, and complicated, with opacities larger than 10 mm in diameter. For all practical purposes, diagnosis of CWP in the living miner is wholly dependent upon the chest radiograph interpretation."

Jan 1, 1995

By Edward L. Tullis

Numerous widely distributed pegmatites of the southern Black Hills of South Dakota contain small amounts of beryl, and two minor deposits are known in the northern Black Hills. Few mines have produced more than 50 tons, and the current, rate of production for the area is about 100 tons annually. Total production, since the first records, is 2,358 tons. Most of the deposits contain less than 1 percent beryl, although the beryl zones in several deposits contain 2 percent beryl or more. Estimated reserves of beryl total 11,824 tons, and an additional 234 tons has been measured; there are other unestimated reserves. The pegmatites are in a belt about the margin of the Harney Peak batholith in the southern Black Hills, although they fail into three districts. The most important, from the point of view of production and reserves, is the Keystone district. Many deposits also are found in the vicinity of Custer and Pringle. Small amounts of beryl occur in the dikes near Hill City. A little beryl has been produced from the Tinton district in the northern Black Hills, and an undeveloped dike has been discovered on Whitewood Peak near Deadwood. The beryl-bearing pegmatites are principally coarse-grained intergrowths or massive segregations of feldspar, quartz, and mica. Some of them contain notable amounts of lithium minerals, as well as some tantalite, columbite, and cassiterite.

Jan 1, 1952

By R. V. Ramani

"In this paper, the current status of respirable dust control in coal mine atmospheres is presented. The advancements in the engineering control of dust generation and entrainment, and of reducing the exposures are summarized. The results of the Health Surveillance Program are briefly reviewed. The results of research conducted in the Generic Mineral Technology Center for Respirable Dust are presented. The 1995 NIOSH criteria document on respirable coal mine dust is briefly reviewed. The fundamental scientific and engineering issues in need of research are discussed. A detailed bibliography is attached.IntroductionFor coal mines in the United States, the current permissible exposure limit (PEL) of 2mg/m3MRE-equivalent concentration (an 8-hour TWA concentration measured gravimetrically) was established by Public Law 91-173: the Federal Coal Mine Health and Safety of 1969 (the 1969 Coal Act). This standard is reduced when the respirable quartz content in the dust sample exceeds 5%; the reduced standard in mglm3 is obtained by dividing 10 by the percent quartz. The OSHA and ACGIB PEL for respirable coal mine dust is also 2 mg/m3 , and OSHA PEL for respirable quartz is 100 µg/m3 . The 1969 Coal Act also prescribed two activities in the Coal Mine Respirable Dust Sampling Program and the National Coal Workers' Health Surveillance Program n to control respirable dust in mines, and the coal worker's pneumoconiosis (CWP) among the coal miners.There are three principal methods by which personal exposures to respirable dust are controlled. The first is engineering control where the aim is to reduce the concentration in the mine atmosphere to or below the mandated level. The second is the provision of personal protective devices which allow the miner to work in dusty atmospheres without increasing personal exposure. The third is the use of administrative controls where the miner's exposure is controlled through work schedules and procedures to keep miner exposure at or under the mandated levels. The 1969 Coal Act specifically prohibits the use of respirators in lieu of environmental control. The compliance sampling program essentially does not give any credit to the use of administrative controls."

Jan 1, 1998

By Jack L. Henry

A laboratory and a pilot-plant-scale investigation has been conducted by the Bureau of Mines to examine possible sources of nitride defects in the production of magnesium-reduced titanium sponge. The production of alpha-stabilized nitride inclusions in hot-rolled titanium plate from air contamination of sponge during its manufacture has been experimentally demonstrated. Magnesium-reduced sponge prepared from air-contaminated magnesium or when contaminated by an air leak during reduction, vacuum distillation, or inert gas sweep, shows very large variations in nitrogen content. Refractory nitrides, delta TiN and epsilon Ti2N have been identified in this sponge. The highest incidence of inclusions resulted from sponge that was reduced by air-contaminated magnesium and from sponge subjected to air contamination during the vacuum distillation cycle and during helium sweep. Air contamination of sponge during the reduction cycle was not nearly as effective in producing inclusions. Tests showed that color and texture may not be reliable criteria for locating defects during sponge inspection. Maintenance of good vacuum-tight integrity, filtration of molten magnesium prior to charging into the reduction retort, and mechanical attrition of sponge to pulverize and disperse nitrides are suggested as practices to lower inclusion incidence in commercial titanium ingots.

Jan 1, 1974

By Arnold O. Tanner

The domestic mining industry gained more strength in 1988 as the healthy comeback that became evident in 1987 continued and grew for many commodities. The increasing and more stable commodity prices, still predominantly in the metals sector, reinforced both the new ways of conducting business and the use of technological advancements in successfully lowering operating costs during the last 4 to 6 years. Some commodities and companies still struggled to survive, but increases in productivity and profits were becoming more common.

Jan 1, 1990

Control shearer-generated airborne respirable dust on longwall mining sections. Approach Previous Bureau studies have shown that using high-pressure water can have a significant impact on the amount of airborne dust released into the face airflow while cleaning and controlling the airflow in the immediate cutting zone. The basic concept to improve the drum water spray system was to utilize high-pressure (1,200 psi) inward-facing drum sprays to improve the dust knockdown efficiency of the spray system and confine the dust to the face area. This system would minimize the exposure of the shearer operator through dust avoidance and decrease face dust levels by suppressing the amount of respirable dust that becomes airborne. System Design In-mine tests were designed to provide information that would permit evaluation of the operation with different spray orientations and water spray pressures. This was achieved by comparison with a conventional baseline wet-cutting system consisting of 26 low-pressure bit sprays, located on the hit blocks to provide pick-point flushing. Total drum water flow was 60 gpm and was maintained continuously throughout all tests. The high-pressure inward-facing drum water spray system consisted of sprays located in each bit block, oriented 15° and 30° toward the face. The inward-facing water spray system was operated at either 800 or 1,200 psi.

Jan 1, 1989