Search Documents

By Forrest T. Moyer

In 1969, the number of fatal injuries in the coal mining industry was lower than in any previous year and the number of nonfatal injuries was lower than in any preceding year except 1968. Fatal injuries in 1969 totaled 203 with frequency rates of 0.85 per million man-hours of worktime and 0.36 per million tons of coal These rates were new annual lows. Nonfatal injuries totaled 9,917 with frequency rates of 41.76 per million man-hours and 17.42 per million tons. The severity rate for fatal and nonfatal injuries combined was 7,359 days lost or charged per million man-hours. The average severity was 173 days lost or charged per injury. These statistics represent the injury experience of an average of 133,302 employees per day working an average of 225 days in 5,955 coal mines for a total of 237-5 million man-hours worked and a coal output of 565 2 million tons

Jan 1, 1973

By T. J. Batchler, T. M. Barczak

The Code of Federal Regulations (CFR) requires that the transverse load capacity of stoppings be equal to or greater than traditionally accepted in mine controls, which for block stoppings is generally accepted as 39 psf as referenced in the preamble to the CFR standard. This measure is based on physical testing of a freestanding wall in accordance with ASTM E 72 specifications, where our past research has shown that the dominant parameter is the tensile strength of the sealant. A new protocol based on rigid arch loading of the structure is proposed to determine the true transverse load capacity of block stoppings. Arching is achieved by the restraint of the stopping against the mine roof and floor, whereby compressive forces are developed within the wall. A laboratory procedure using the NIOSH Mine Roof Simulator (MRS) to simulate rigid arching of block stoppings was developed and results verified through full-scale in-mine tests. The rigid arch tests have demonstrated transverse load capacities more than an order of magnitude higher than the ASTM E 72 evaluation method from which the 39-psf requirement is derived. More importantly, the rigid arch tests have shown that the load capability is dependent on the physical properties of the block and geometric properties of the wall and not the sealant.

By Richard Mainiero

In any construction project involving explosives, care must be taken to protect workers from carbon monoxide (CO) generated by blasting operations. CO is an odorless, colorless gas that can cause illness and death by asphyxiation. In general, the first symptoms include headache, fatigue and lightheadedness. At higher exposures to CO, skin flushing, rapid heart rate, and lowered blood pressure occur. At ever, higher exposure levels, decreased attention span is followed by nausea, vomiting, unpaired coordination, fainting, coma, convulsions and, finally, death. The detonation of explosives in blasting operations generates a range of toxic fumes, but CO is the most insidious because it is colorless, odor less, and is long lasting, since it is not readily removed try reaction with ground water, soil or rock. Additionally CO is generated in relatively large quantities compared to other toxic: fumes. CO may continue to seep out of blasted material long after the odor commonly associated with detonated explosives has dissipated. It is never safe to assume as confined space in the vicinity of a blast is clear of toxic fumes. CO may be present even if the area looks Clear and many hours have passed since the last blast.

Jan 1, 2000

By R. E. Heithecker, D. B. Taliaferro

"INTRODUCTION Recovery of core specimens from subsurface formations and their subsequent analysis are important aids in efficient development and operation of oil and gas fields. Gore specimens first were obtained mainly for the geologic information they revealed; now they are analyzed to determine many of the physical characteristics and conditions of the subsurface formations as well. Cores recovered from the producing formations may be analyzed for porosity, permeability, oil content, ""connate"" water content, and other physical and chemical properties of the formation, all to the end of furnishing enough data for making reliable estimates of the quantity and avail¬ability of oil and as within a reservoir and in devising efficient means for their withdrawal.Examination of bottom-hole samples of oil gives valuable information concerning the amount of gas in solution in the oil within the reservoir and the resultant shrinkage of the oil when the gas is released. Producing characteristics of reservoirs nay be determined by means of subsurface pressure and temperature gages and measurements male at the wellhead; however, unless reliable core analyses are available, these data have only limited use in any quantitative study of reserves. In such a study the quantity of oil, gas, and water contained in a unit volume of the reservoir formation is extremely important. Although reliable methods of analyzing cores have been developed and the data thus obtained are valuable, their applications become more limited or reservoirs at higher temperatures and pressures are discovered. This condition results almost entirely from the fact that in recovering a core from a formation of high pressure and temperature by present methods a large part of the fluid content of the core is lost or contaminated to an unknown extent. For a number of years most petroleum engineers have held that if this loss and contamination of the fluid content of a core were eliminated, the value of core analyses would be increased greatly."

Nov 1, 1939

By Robert M. Koerner

The feasibility of using small-scale models to simulate residential masonry foundation walls subject to fatigue loading was investigated. Five wall segments were modeled in one-quarter scale using dynamic similitude equations. The walls were dynamically loaded using a sinusoidal base motion and wall accelerations were monitored. The stiffness, natural frequency response, and damping characteristics were measured. The number of cycles of testing necessary to cause initial visible cracking was recorded. Analysis of the data indicated the importance of the relationship between the forcing function and the natural frequencies of the structure in influencing cracking damage.

Jan 1, 1980

By Thomas M. Barczak

Secondary roof support systems play a vital role in preserving the safety of underground mine workers by preventing the unintentional collapse of the mine roof. Hundreds of thousands of standing roof supports are constructed each year in underground coal mines. Historically, wood and concrete cribs and timber posts have been used for secondary roof support. These support constructions require the handling of heavy and bulky materials, causing numerous injuries to the mine workers and resulting in more than 40,000 lost workdays in the past 9 years. Since 1993, various alternative support technologies have been developed. These new support technologies not only provide superior roof support, but many also have significant material handling advantages by using smaller and lighter weight materials, fewer components, mechanically installed support systems, and pumpable support systems. The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive material handling research and has developed recommended lifting thresholds to reduce material handling injuries. An analysis of roof support construction reveals that conventional support materials used in wood and concrete cribbing exceed the recommended lifting thresholds, while the engineered support systems are closer to the recommended weight thresholds. Finally, recommendations are made relative to proper lifting techniques and material handling practices to prevent injury to mine workers when constructing roof supports in underground coal mines.

Jan 10, 2000

By Clarence Hall, CHARLES F. MUNROE

Of the common causes of the larger mine accidents, such as falls of roof and coal, gas and dust explosions, mine fires, and the misuse of explosives, all of which are often closely related, each must be studied and fought in a manner peculiar to itself. The last mentioned, the misuse of black powder and other explosives, is sometimes considered the least important of these causes of mine accidents; but its impor- tance is much greater than the statistics indicate, for the reason that the misuse of explosives is the true cause of many of the fatal mine fires, gas or dust explosions, and falls of roof that are credited to other causes. Both the quantity of explosives used and the number of purposes to which they are applied are increasing. They are now made at about 150 plants, in different parts of the United States, and the product of a single year is estimated at nearly 500,000,000 pounds. Nothing in all this material is a safe or "safety" explosive when in the hands of a careless or ignorant person; and this is true whether considered in connection with the shipment or the use of these explosives. In addition to the large losses of life and property resulting from an improper use of explosives in mining, the recent statistics of the railway bureau for the safe transportation of explo- sives have shown more than 400 persons killed or injured and over $3,000,000 worth of property destroyed by explosives in transit by rail. The fact that three years of cooperative effort under the wise supervision of this bureau has reduced these losses to almost nothing encourages the hope that similar cooperative effort may likewise greatly lessen losses of life and property from the use of explosives in mining. The additions to the large death roll of our mines make a recurring appeal to the public for fair treatment of the coal-mining industry, and to the miner and the manager that they join in every possible effort for greater safety. It may never be possible under conditions such as exist to-day to prevent mine accidents entirely. Little can be accomplished in that direction by either the operators or the miners working alone, but experience in all countries shows that

Jan 1, 1911

By Frank Parrish

THIS REPORT by the Federal Bureau of Mines presents data on water-supply wells used by waterflood operators in North Texas and shows the distribution of permeable source sediments. Averages of well characteristics, including static fluid levels, working fluid levels, net thicknesses, producing rates, and depths, are presented and discussed. Essentially all water used in waterflooding is mineralized water from consolidated sediments. This study is concerned with the geology and distribution of these mineralized source sediments, whereas previous work in this area was predominantly a study of shallow sources of potable water. Tables, isopachous maps, and electric-log cross sections are included to describe the several source aquifers. In general, water-producing capacity increases with depth of the sediments. Wells completed in Cretaceous sediments 82 to 600 feet deep yield 50 to 600 barrels of water daily, whereas those completed in Pennsylvanian sediments 360 to 4,110 feet deep yield 100 to 7,000 barrels daily. Although deeper formations are used where oil and water are produced conjunctively and where large withdrawal rates are required, insufficient well data prevented mapping of deeper formations.

Jan 1, 1961

By W. G. Sandell, L. C. Bauerle, K. C. Dean

"INTRODUCTION As a part of the wartime activities of the Bureau of Mines, metallurgical services were extended to other Government agncies engaged in purchasing and stock-piling some of the more critical and strategic materials. At the request of Dr. Alan M. Bateman, special representative of the Metals Reserve Company, metallurgical studies were made on three samples of oxide tin ore from, the States of Zacatecas and Guanajuato, Mexico. The samples were submitted for testing by A. Porraz of the Financiera Miners, S. A., institution Financiera, Edificio Guardiola, Despachos 500-507, Mexico, D. F.The samples as received were marked Nos. 1, 2, and 3 and described as follows:Sample 1. - Origin: Mining camp ""El Naranjo,"" municipality of Sombrerete, State of Zacatecas, Mexico. This sample was partly concentrated by washing and as received was all minus 10-mesh in size.Sample 2. - Origin: Deposits in Sierra. Fria and Juan Cherey, municipality, of Jerez,State of Zacatecas, Mexico. This sample represented run of-mine ore.Sample 3. - Origin: Mine ""La Frontere, "" Ranch of San Pedro del loya, State of Guanajuato, Mexico. This run-of-mine sample was low in tin content but came from a highly mineralized tin field."

Jun 1, 1947

By D. J. Bauer

Oxidation of mixed lanthanide solutions with ozone at pH 4.5 and at ambient temperature resulted in precipitation of 98 percent of the original cerium present. Corresponding cerium purity was increased from 50 to 98 percent. A second ozone oxidation-precipitation step produced cerium of 99.9 percent purity in high yield from the 98-percent-pure material. Alternately, ozonation at pH 6.5 and 85° C differentially precipitated cerium and rare-earth elements heavier than cerium and left 89 percent of the original lanthanum in solution at a purity of 95 percent. Subsequent recovery of cerium from the heavier rare-earth elements in the precipitate was accomplished by dissolving the precipitate in dilute mineral acid and reoxidizing the cerium with ozone at pH 4.5 and at ambient temperature. The filtrate contained an enriched praseodymium-neodymium-samarium-europium mixture that is amenable to separation by ion exchange or solvent extraction.

Jan 1, 1968

By Rogers F. Davis

This publication has been prepared to supply manufacturers and industrial users a listing of mobile diesel-powered equipment and subassemblies approved and certified by the Bureau of Mines for use in nongassy noncoal mines and tunnels. This revised and supplemented listing supersedes an earlier publication2 released in 1963. Testing of diesel-powered equipment is one phase of the Bureau's program of health and safety that concerns approval of electrical and diesel equipment designed to prevent explosions, fires, shocks, or toxic hazards in underground mines, when such equipment is used and maintained properly. Manufacturers submit machinery and component parts to the Bureau for study of their design, safety features, and use. Equipment must pass exacting tests and must meet strict requirements established through research and experience and outlined in the Bureau's permissible schedules before the Bureau approves it for safe use in mines.

Jan 1, 1968

By Stanton L. Tainter

As a part of a wartime program to aid in the development of known ore bodies and in the discovery of hitherto unknown deposits of strategic minerals, the Bureau of Mines investigated the feasibility of diamond-drilling the Christmas copper deposit, in Gila County, Ariz., to increase the reserves of milling ore. Upon recommendation of the examining engineer, drilling was begun in September 1942, from the bottom (770) level of the mine. One month later, in cooperation with the Bureau, the Federal Geological Survey started geologic mapping of the mine workings. Since extensive and costly development would be required, the War Production Board concluded that ore below the bottom level could not be mined at that time because of the wartime shortages of equipment and man-power. In January 1943, drilling was moved to the 300 and 400 levels to locate reserves readily accessible for continued production of fluxing ore. This drilling, which was under the supervision of L. G. Marshall, was completed in January 1944.

Jan 1, 1948

By Walter Murphy

For a number of years the Bureau of Mines has been studying the properties of crude petroleums produced in the United States and the Western Hemisphere. A number of reports have been published giving the analyses of crudes from the different fields and regions as made by the Bureau of Mines Hempel method of analysis.4 Several of these reports include analyses of crude oils from the Rocky Mountain region.5/ The search for new fields and new producing horizons in old fields in the Rocky Mountain region has been quite intensive during the last few years, and a number of discoveries have been made.

Jan 1, 1937

By B. J. CROSS., Henry Kreisinger, John Blizard, C. E. Augustine

This bulletin presents the results of 36 tests made on a 468-horsepower Edge Moor boiler fired with pulverized coal at the Oneida Street Station of the Milwaukee Electric Railway & Light Co., Milwaukee, Wis. The tests were made by the fuel section of the United States Bureau of Mines in cooperation with the research department of the Combustion Engineering Corporation. Illinois coal was used as fuel; the furnace, burners, and feeders were designed by the Locomotive Pulverized Fuel Co. The object of the tests was to determine what over-all boiler efficiency could he obtained with pulverized coal under various conditions of furnace operation and with coal of different fineness and moisture content. The investigation was thorough. The pulverized coal, as it was supplied to the furnace, was weighed in specially designed tanks placed on platform scales. Twenty-nine of the tests were of 24 hours duration, three of 16 to 18 hours, and four of 12 hours. All tests are reported excepting two-8 and 20-which had to be stopped abruptly, No.8 because a motor actuating the coal-feed screw burned out and No. 20 because of trouble with the feed pump. Tests 1 to 27, inclusive, were made with round burners and tests 28 to 3Rwith spreading burners. In the first nine tests a large excess of air was supplied in an effort to prevent the ash fusing at the bottom of the furnace. In tests 10 to 16 the supply of excess air was reduced in order to get a high efficiency, regardless of the slagging of ash at the furnace bottom. Tests 17 to 27 were made with a water screen about 10 inches above the bottom of the furnace, to make possible the burning of coal with a small supply of excess air without the ash fusing at the bottom of the furnace. Tests 28,29, and 30 were made without the water screen and with a small supply of excess air, and tests 31 to 38 with a water screen around the walls near the bottom of the furnace. Tests 32, 33, 34, and 35 were run with coarser coal than that used ordinarily at the plant. Tests 36,37, and 38 were made with undried coal.

Jan 1, 1923

By Liming Yuan, John C. Edwards, Gene F. Friel, Robert A. Franks

Diesel fuel fire experiments were conducted in NIOSH’s Pittsburgh Research Laboratory’s (PRL) Safety Research Coal Mine (SRCM) to determine the critical air velocity for preventing smoke rollback. Such information is necessary for the preplanning and implementation of ventilation changes during mine fire fighting and rescue operations. The fire intensity varied from 50 kW to 300 kW depending upon the fuel tray area. Airflow in the 2 m high and 2.9 m wide coal mine entry was regulated during the course of each experiment; measured upwind from the fire as an average over the entry cross-section with an ultrasonic airflow sensor; and recorded dynamically with a mine monitoring system. The extent of smoke reversal was monitored with light obscuration monitors, ionization smoke sensors, and visual observations. Experimental results for the critical air velocity for smoke reversal as a function of fire intensity compared very well with model predictions based upon a computational fluid dynamics (CFD) fire dynamics simulator.

By J. W. Miller

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and from the data developed, to determine: (a) Which coals either as mined or after beneficiation by conventional preparation are suitable chemically under present standards for producing metallurgical coke. (b) Which coals require special and more intensive treatment in preparation than is now practiced. (c) Which coals cannot be considered potential sources of metallurgical coke regardless of preparation. This report is one in a county series that describes the preparation characteristics of the coals of Mingo County, W. Va.

Jan 1, 1956

By Russell R. Trengove

Bureau of Mines exploration at the property of the Tulare County Tungsten Mines was by core drilling from the surface from May 16, 1950, to July 13, 1950. The property is in the western foothills of the Sierra Nevada Range, 18 miles northeast of Lindsay, Calif. It has been in almost continuous production since 1942 and has produced 40,831 units of tungsten trioxide (W03) with a grade of approximately 67 percent. The work performed comprised a study of the geology, mapping the area, sampling the outcrops, and diamond drilling the area adjacent to the mine workings. Ten holes were drilled for a total of 1,824 feet. Ore reserves were found to be confined to tactite zones in a surface area approximately 250 by 400 feet and extending downward about 350 feet.

Jan 1, 1956

By N. A. Eilertsen

The Aroostook manganese-bearing deposits lie within a rectangle 30 miles wide and 70 miles long. Over 40 different deposits have been discovered in this area, but they have not been mined because the ores are difficult to treat. In 1949, the Maple Mountain area was selected for detailed investigation by the Bureau of Mines, because study by the State of Maine and the Federal Geological Survey indicated that it was the most promising in Aroostook County for developing a large tonnage of reserves. Investigation by the Bureau of Mines disclosed that all of the reported deposits of the central district were located on the limbs of a syncline underlying a pear-shaped area of 283 acres between the crests of Maple Mountain and Hovey Mountain. The ore area has been outlined by trenching and drilling along three sides of the perimeter, while the remaining side is defined by a fault. The area has a length of 6,300 feet and a maximum width of 3,100 feet. Diamond-drill holes have intersected the deposit as deep as 1,550 feet below surface, but additional deep drilling would be required to determine the intensity of folding or warping at depth. The Maple Mountain-Hovey Mountain deposit lies in the slates of Ordovician age and is classified into three zones, of which the upper, averaging about 57 feet thick, is designated manganiferous purple and red slate. The central zone, also averaging about 57 feet thick and containing the highest manganese content, is manganiferous, banded hematite. The lower zone is manganiferous, interbedded hematitic and green slate with an average width of about 33 feet. Manganese minerals occur with hematite in all three units. Trenching on the northwestern slope of Hovey Mountain uncovered other disconnected deposits of manganiferous rocks of earlier age than the ore of the syncline. The general strike of these deposits, which range from 15 feet to 75 feet in thickness, is southwest a length of 5,000 feet. They dip steeply southeast. The ore of the syncline is predominantly deep, hematitic red, inclining to red-dish black, fine-grained, dense, and thinly laminated. It is hard and siliceous. Hematite has, in places, been altered to magnetite. Because of the fine-grained texture of the ore, the manganese-mineral constituents are difficult to determine. Of the manganese silicates present, braunite is the most readily identified. Manganese carbonates and oxides are found also.

Jan 1, 1952

By Constantine C. Popoff

This report reviews and analyzes, by a simple analytical and logical reasoning, the conventional methods of reserve computations of mineral deposits described in various domestic and foreign publications. It brings together, formulates, and evaluates the principles underlying interpretation of exploration data; and ties such principles to the proposed classification of methods. The material is discussed in sufficient detail to allow general application.

Jan 1, 1966

By Jr. Gabler

World resources of cobalt appear ample for the foreseeable future; however, political and economic events have caused concern over the availability and reliability of an uninterrupted supply. Because of this concern, the U.S. Congress requested that the U.S. Bureau of Mines initiate a study of the flow of cobalt in the economy that would delineate and quantify the production areas where metal values are lost. As a result, the Bureau has developed a computerized commodity flow model. A major attribute of this model is that it is amenable to updating as supply, demand, and/or production data change. This report follows the flow of cobalt through its metallurgical and chemical applications and highlights areas where significant losses occur due to downgrading, export, or disposal. The study indicates that about 4,300,000 lb of cobalt-bearing materials are lost each year, representing 24 pct of U.S. domestic demand.

Jan 1, 1990