Search Documents

By Robert Vinson

This article examines the spatial variability of dust concentrations within a coal miner?s breathing zone and the impact of sampling location at the cap lamp, nose, and lapel. Tests were conducted in the National Institute for Safety and Health Pittsburgh Research Laboratory full-scale, continuous miner gallery using three prototype personal dust monitors (PDM). The dust masses detected by the PDMs were used to calculate the percentage difference of dust mass between the cap lamp and the nose and between the lapel and the nose. The calculated percentage differences of the masses ranged from plus 12% to minus 25%. Breathing zone tests were also conducted in four underground coal mines using the torso of a mannequin to simulate a miner. Coal mine dust was sampled with multi-cyclone sampling cans mounted directly in front of the mannequin near the cap lamp, nose, and lapel. These four coal mine tests found that the spatial variability of dust levels and imprecision of the current personal sampler is a greater influence than the sampler location within the breathing zone. However, a one-sample t-test of this data did find that the overall mean value of the cap lamp/nose ratio was not significantly different than 1 (p-value = 0.21). However, when applied to the overall mean value of the lapel/nose ratio there was a significant difference from 1 (p-value < .0001). This finding is important because the lapel has always been the sampling location for coal mine dust samples. But these results suggest that the cap location is slightly more indicative of what is breathed through the nose area.

Jan 1, 2007

By S. Harteis, D. Dolinar

Many mining operations rely on bulkheads to provide a barrier between impounded water or slurry and active mine workings. However, bulkhead failures could cause and have caused catastrophic flooding that puts the underground workforce at risk. The National Institute for Occupational Safety and Health1 (NIOSH) in collaboration with the Mine Safety and Health Administration (MSHA) is conducting research to evaluate the adequacy of existing design practices for water and slurry bulkheads. A key component of this research effort is documentation of the performance history and design parameters for bulkheads installed in underground coal mines during the last 20+ years. This research is part of a larger effort to develop general design guidelines and procedures for constructing and maintaining bulkheads that will help to ensure their long-term structural integrity, while significantly reducing the inundation risk for miners. This paper presents the results of NIOSH’s research to identify state-of-the-art bulkhead designs, including design criteria, leakage monitoring systems, and emergency warning systems. Underground observations and evaluations of existing bulkheads suggest that the most important design factors influencing their performance are the interface of the bulkhead with the surrounding strata and the potential magnitude of the hydraulic pressure to which they may be subjected. When a bulkhead has failed, leakage has generally been through the surrounding strata or along the bulkhead/strata interface, with the failure potential along the interface increasing with hydraulic head. It was also determined that development of a monitoring program to ensure the long term structural integrity of bulkheads is an important safety consideration. Current monitoring procedures range from weekly visual inspections to constant monitoring via pressure transducers and fluid level indicators. Where possible, these devices are used in conjunction with a computer based mine monitoring system to alert mine personnel when an emergency condition exists at the bulkhead installation.

By William G. Pariseau

The research reported here concerns ground control in multi-seam mining and relates mainly to the analysis of stress about multi-seam room and pillar mines. The two variables of most concern are distance between seams and alignment of pillars between seams. The first year results of the two year investigation apply to the development phase of mining when the extraction is typically less than 50 percent. The second year effort is concentrated on retreat mining and barrier pillar safety when the extraction is typically greater than 50%. The procedures in both cases are readily applicable to more than two seams. Although two seam mines are the most frequent type of multi-seam operations, because of the potential for three seam operations in the Western United States, a number of three seam development analyses are also presented. The results enable one to make a rapid assessment of stability of rooms and pillars during production and barrier pillar size during extraction of adjacent panels. In the event of low safety factors, more site-specific analyses can be undertaken.

Jan 1, 1983

By Fredrick L. Johnson

No mineral resources were identified during the investigation of the White Cloud-Boulder RARE II area. Only a few claims have been located in the area and only two workings were found. However, there has been considerable exploration and mining activity near the RARE II area. Sand and gravel resources are abundant but similar deposits occur closer to market areas. There are no known coal, oil, or gas deposits. Most of the RARE II area is underlain by volcanic rocks. The likeliest host rocks for metallic minerals are the metasedimentary rocks exposed in the south part of the area; there is potential for zinc and silver resources at a prospect in that part. Traces of scheelite and powellite were observed in the Kent Peak-Ryan Peak area along hair-line fractures in calcareous country rock. While no significant concentrations of the minerals were found, their presence, a northwest alignment of prospects with similar deposits, and an abundance of dikes near the deposits, suggest that the intrusive system (Summit Creek stock) exposed near the head of Little Fall Creek may extend to the northwest under the RARE II area.

Jan 1, 1983

By Michael W. Redifer

A Fortran IV computer program was developed to calculate the composition at equilibrium of products from a set of high-temperature gas combustion reactions. The program was used to develop high-temperature equilibrium concentration profiles for various constituents as a function of temperature and oxygen concentration. The computer program was specifically applied to reactions pertaining to the corrosion of superheater tubes in pulverized coal-fired boilers; however, it is useful for any multicomponent, multireaction scheme in which equilibrium constant data can be obtained and is comprised of gaseous reactants along with finely dispersed solids or liquids. General applicability of the computer program, including its limitations, are discussed along with detailed instructions for using the program.

Jan 1, 1973

By Forrest T. Moyer

The safety record of the mineral and mineral-fuel mining and processing industries in 1966 was improved slightly for the second consecutive year as indicated by reduced injury-frequency and injury-severity rates. The overall operating activity was higher in 1966, as measured by the increased number of men working and the total man-hours of worktime. Injury Experience.-The rate of occurrence of all disabling work injuries in the mineral industries was 17.38 per million man-hours in 1966. This overall rate comprised frequencies of 0.28 for fatal and 17.10 for nonfatal work injuries, compared with respective rates of 0.28 and 17.26 in 1965. Fatalities totaled 543; 5 more than in 1965. The total of 33.091 nonfatal injuries was 291 higher than in 1965. However, the larger number of disabilities was offset by the increased worktime in 1966. so that the fatality frequency was unchanged and the nonfatal frequency rate decreased from 1965.

Jan 1, 1967

By Nathan Feldstein

The wetting of coal dust by aqueous solutions of surface active agents (surfactants) has been studied. Selected for study were thirty coals and typical surfactants selected from the typical classes of anionic, non ionic and cationics. Of these three classes the practical use of cationics in aqueous solutions has been eliminated due to the inherent negative Zeta potential charge of the representative coals studied. The wetting of the coals has been examined by column flow, contact angle, and settling rate measurements. Results indicated that both anionic and nonionic surfactants are to be considered viable for use; low critical micelle concentration values are also preferred for the surfactants. Study of native waters showed substantial variation in properties, i.e., pH, calcium ion concentration, and conductance. pH variations were also noted to affect the effectiveness of selected surfactants. Combinations of nonionic and anionic surfactants have, in certain instances, produced synergistic enhancement in the coal wetting superior to the effectiveness of each surfactant alone.

Jan 1, 1981

By E. K. Stanek

This report contains the results of an investigation into the feasibility of periodically measuring parameters of the insulation for a mine electrical power system in order to detect incipient faults. The variety of insulation parameters evaluated included insulation resistance, dissipation factor, power factor (vs. applied voltage), current harmonics, leakage current, infrared radiation, as well as certain circuit breaker parameters and tests. In order to augment field tests a program of accelerated life testing was also carried out. Apparent inconsistencies in data were identified as the result of environmental effects, primarily temperature and relative humidity. A series of environmental tests were conducted to develop correction factors that allow one to refer measured parameters to standard conditions. A portable data collector was develop-ed to aid in the accurate collection and analysis of laboratory and field data. The primary conclusion is that insulation deterioration can be measured and failure predicted with reasonable confidence. The secondary conclusion is that most of the tests are impractical in the field although useful in the laboratory. Infrared sensing, insulation resistance and dissipation factor are the best insulation field tests when portability is taken into account.

Jan 1, 1979

By A. W. Ambrose

A few years ago, (March 3, 1915) Congress passed a law providing for the establishments of ten mining experiment stations under the supervision of the Bureau of Mines. In 1917 the Secretary of the Interior decided that one of these stations should be devoted to Petroleum, and in the early part of 1918, approved the establishment of the Petroleum Experiment Station at Bartlesville, Oklahoma, upon the condition that the city furnish the site for the buildings and guarantee $50,000. for the erection of the buildings. A building site of 5 acres and the necessary building fund was furnished by the Bartlesville Chamber of Commerce.The buildings consist of an administration and laboratory building, both of brick construction. The former is a two-story structure of eight rooms. A large room occupying over half of the main floor is devoted to the library, reception room, and clerical force. The remaining rooms comprise a drafting room and six offices occupied by the staff assigned to this station. The laboratory is a one-story brick building and contains a well-equipped chemical and physical laboratory, also a machine shop and mechanical laboratory. In addition to the main buildings there now are on the property an experimental refinery, a blue-print house, and a store house. These latter buildings are all of sheet-iron construction.

Oct 1, 1920

By L. D. Patts, J. D. Noll, S. E. Mischler, G. H. Schnakenberg

In this study, we evaluated the ambient diesel particulate matter (DPM) concentrations (at the intakes and exhausts of the mine) as the entire vehicle fleet of a stone mine switched from using 35% biodiesel to using a water emulsified fuel (PuriNOx). Elemental carbon (EC) was reduced by 45% when a PuriNOx blend containing 10% water replaced 35% biodiesel and by 57% when a PuriNOx blend containing 20% water was used. Other factors such as engine duty cycle and production changes could potentially cause some day-to-day EC fluctuations, and no direct comparison to commonly used dieselfuels (No. 1 or No. 2) was achieved. Therefore, a second study was performed in a controlled “isolatedzone” environment to fametal mine, comparing PuriNOxto No.1 diesel fuel in a load haul dump vehicle. The EC fraction of the DPM was reduced by about 71% when the PuriNOx blend containing 10% water was used and by about 85% when the PuriNOx blend containing 20% water was employed. This study did not determine how the water emulsified fuel would affect the engine or power.

By James M. Spear

The U.S. Bureau of Mines conducted a mineral survey of the Domeland Addition (5207) and Woodpecker (5206) RARE II areas during the summer of 1979. These study areas were examined to determine the presence or absence of mineral resources and reserves and where possible, to estimate values. The study areas are 9 air mi northeast of Kernville, California, and encompass 47,400 acres of primarily granitic rocks of the Sierra Nevada batholith with some scattered exposures of older metasedimentary, volcanic, and metavolcanic rocks. These other rock units partially surround the exposed batholith in the Domeland Wilderness and consist mostly of late Paleozoic quartzites, mica schists, marbles, and meta-volcanics, Mesozoic quartz diorite and gabbro intrusives, and local Tertiary basalt and andesite flows.

Jan 1, 1981

By Christopher C. Jobes, Alan G. Mayton, Timothy J. Matty, Joseph P. DuCarme

Mining injury statistics show that a significant number of back, neck, and head injuries are linked to exposure from vehicle vibration. Use of a suspension seat is a common way to isolate the vehicle operator from the adverse effects of vibration exposure. Thus, researchers at the National Institute for Occupational Safety and Health1 – Pittsburgh Research Laboratory (NIOSH – PRL) performed laboratory studies on four passive and two semi-active seat suspension designs. These are typical of seat suspensions commonly found on large off-road heavy surface mining, construction and agricultural vehicles as either replacement or original equipment manufacturer (OEM) systems. One included a pneumatic (air bladder) spring mechanism. The fifth and sixth suspensions were a NIOSH magnetorheological (MR) semi-active damper design based on the pneumatic (air bladder) and one of the coil spring suspensions above. These suspensions were modified with a commercially available MR damper substituted for the OEM damper. These six seat suspension systems were tested and analyzed, for vertical vibration only, using the ISO 5007 Standard [1]. This paper describes the laboratory vibration tests using a MTS® shaker table and discusses the results obtained for the different suspension designs and highlights the rheonetic technology studied. Implications of the seat suspension designs relative to their capabilities for isolating vehicle operators from vibration exposure are discussed. Results for suspensions 1 through 3 showed frequencies of isolation from 2.1 to 3.0 Hz using the 40-kg (88-lb) mass and from 1.65 Hz to 1.8 Hz using the 80-kg (176-lb) mass. Suspension #4, in tests with only the 80-kg (176-lb) mass, showed an isolation frequency of 3.7 Hz. With the MR damper added to seat suspension #4, the peak transmissibility was lowered from 1.3 to 0.95 and showed a corresponding downward shift in frequency from 2.25 Hz to 1.4 Hz. In fact, the results for suspension #5 (the MR damper added to seat suspension #4), using test #3 conditions of the programmed control algorithm, showed isolation (attenuation of transmitted vibration) throughout the test frequency range from 1.0 to 6.0 Hz.

By Ernest A. Curth

The Bureau of Mines studied pressure changes in coal pillars by using encapsulated hydraulic pressure cells to measure relative changes in stress developed during mining. The data indicate that (1) abutment stresses were detected when the pillar line is within 42 to 100 feet, (2) vertical pressure increases as coal is mined in the pillars, (3) at first pressure is higher at the edge of the pillar than in the core, but as mining progresses, the higher pressure is measured in the core of the stump, and (4) in the two instances where lateral pressures were measured, they remained lower than the vertical pressures during pillar extraction. The data also indicate that the mean vertical pressure increase, 6P, in a pillar is roughly related to the percent of pillar extracted, A, by the empirical parabolic equation

Jan 1, 1967

By William W. Adams

A larger measure of safety attended the operation of the stone quarries and related plants in the United States during the calendar year 1935 than in any other year for which annual records are available for the industry. The accident rate, covering fatalities and nonfatal injuries that disabled an employee beyond the remainder of the day on which the accident occurred, was 38.19 per million man-hours of work performed. The nearest approach to this favorable record was in 1932 when the rate was 38.48. The rate for 1934 was 41.82; hence the record for 1935 was 9 percent better than that for 1934. Reports from operating companies showed that 51 men were killed by accidents in 1935 and 4,152 men were injured. (See table 37.) The industry employed 73,005 men and performed 110,033,341 man-hours of labor, an average of 1,507 hours of work per man. Measured in man-days, the total volume of labor was 14,623,303, or an average of 200 days of 7.52 hours per day for each man employed. These figures are not strictly comparable with similar figures for the preceding year, as the, coverage of the industry was more complete for 1935 than for 1934 because special facilities were available to the Bureau of Mines for conducting the 1935 canvass that were not available for the 1934 canvass. Reports covering identical plants that were active both in 1934 and 1935 indicate a reduction of about 7 percent in the number of men employed in 1935. This fact suggests that the apparent increase in the number of workers in 1935 is attributable chiefly, if not entirely, to the more complete coverage of operating plants in 1935. The plants from which this inference is drawn employed 21,799 men in 1934 compared with 20,248 in 1935.

Jan 1, 1937

By I. AITKENS

The basic mining law of Cuba is contained in the basic Spanish mining decree having the effect of law December 29 , 1868. This legislation has remained substantially unchanged , with the exception of a few minor administrative changes made by the present Government . These changes provide for the register of mines , oil wells , and operations of such nature , and also provide for the keeping of records showing the value of minerals taken out . By Royal decree of April 17 , 1883 , the law of mines enacted for the Peninsula ( Spain ) on July 6 , 1859 , and the General Bases of December 29 , 1868 , were declared in force in Cuba . In order to encourage the mining of iron org , in 1883 the Crow of Spain issued a royal decree to the following effect.

Jul 1, 1931

By L. L. Rethi

The U.S. Bureau of Mines summarized injury data for independent contractor employees working at all locations of coal and metal-nonmetal mines from 1983 through 1990. During the eight years, the greatest contrast in degree of injury between independent contractor and operator employees was in fatalities. From 1983 through 1990, there were 132 independent contractor employee fatalities in the mining industry. In 1988 though, independent contractor employees accounted for nearly one-fourth of all mining fatalities. The fatality incidence rates of independent contractors were consistently higher than those of operators during the eight years. For instance, in 1990, the contractors&apos; rate was twice that of operator employees in coalmining and nearly five times that of operators in metal-nonmetal mining. Three other salient facts highlight the independent contractor employees&apos; fatality injury data during these years. First, 82% of the independent contractor employee fatalities occurred at surface locations. Second, two job classifications?truck driver and equipment operator?represented 37% of the fatalities throughout the 8-year period. And finally, four accident classifications?powered haulage, slips and falls, machinery, and electrical?accounted for 71% of all independent contractor employee fatalities.

Jan 1, 1993

By Albert H. Fay, Herbert M. Wilson

The national mine-safety demonstration at Pittsburgh, Pa., was projected and undertaken in the hope that it would aid the increase of safety in the mining industry. That the national mine-safety demonstration was warranted and has served a useful purpose was evidenced by the attendance, not only at the public demonstration in Forbes Field, but also at the more special exhibit of the work of the Bureau of Mines at the arsenal grounds and at the experimsntal. mine. Nearly 2,000 persons witnessed the demonstrations and exhibits of the Bureau of Mines at the arsenal grounds on the morning of October 30, 1911. The spectators were all mine operators, miners, or persons interested in mining, and represented operations in all parts of the United States. Nearly 1,200 of these persons visited the bureau's experimental mine at Bruceton to witness ~th~explosion of coal dust. Had the weather, which was exceptionally inclement, been more favorable, there would doubtless have been a much larger attendance. At the public demonstration in Forbes Field, which· was witnessed by President Taft, from 12,000 to 15,000 persons, chiefly mining men, were present and attested their interest and enthusiasm in the minesafety exhibits by remaining throughout the proceedings, regardless of the rain which fell all the morning .. Sincethis demonstration, the organization of first-aid corps and of rescue corps has been undertaken at mines where there had previously been no such organizations. The bureau has received letters of commendation attesting the value of the demonstration in drawing· attention to the dangers and to possible means of greater safety in mining. Many of these letters have urged that the results of the demonstration be published for the guidance and instruction of those who were present. In response to these reauests the following account of the mine- BlIIeLY demonstration lias been prepared. IIi its preparation various division and section chiefs of the Bureau of Mines have cooperated. The authors acknowledge the assistance they have received from those section chiefs and other members of the bureau who contributed detailed descriptions of apparatus exhibited at the demonstration or of investigations represented.

Jan 1, 1912

By K. R. Dorman

To further investigate the potential of precast concrete sets as a support medium for underground mines, the Bureau of Mines designed a five-piece precast concrete drift set for a small opening and tested it to destruction in a straining frame. Twenty-seven tests were made with three sizes of members using three loading conditions. In addition, six tests were made with sets in a distorted configuration, Test results and typical failure patterns are presented. A comparison of results with those previously reported for the three-piece set shows the five-piece set supports considerably larger total loads than does the three-piece set of equivalent cross section designed for the same size of opening. Recommendations are made for improvements in design.

Jan 1, 1969

By H. S. Auvil, L. D. Schmidt, H. G. Graham

"Several studies on the bulk density of coals prepared for byproduct-oven use were undertaken during the war by the Bureau of lanes in cooperation with the Office of the Solid Fuels Administrator and with the advice of the Coke Production Committee. The primary purpose of these studies was either to produce more uniform coke or to increase the throughput of existing facilities or both; the goal was increased Production of steel for war. As these studies were made, detailed reports were sent to the individual companies with whom the Bureau cooperated; also two reports,5/6/on the general subject of bulk-density control were published. In the course of the work, data were gathered that now prove of value in judging the merit of carious methods of testing bulk density and the limits of application of each method in byproduct-oven operations.Since the cessation of hostilities, the .Bureau section (Coke Production Survey Section) that conducted this work has been liquidated, but it was felt advisable to prepare a report on the accumulated experience so that it would be in a form available for the use of the industry and also as a base for any further research on the control of fluctuating bulk densities in coke ovens.It is hoped that the data and experiences recorded herein will be of material assistance to the many who have had difficulty in obtaining reproducible results in bulk-density testing. Since the data were gathered in the course of extending aid to individual plants in minimizing the deleterious effects of fluctuations in bulk density of oven charges on the quality and quantity of coke produced, certain desirable phases of an over-all investigation were not covered. However, on certain of these phases qualitative indications are available and the policy followed herein is that suggested by the American Society for Testing Materials Manual on Presentation of Data7/ that lacking quantitative information, relevant material should be included even though it ""may be qualitative in character, some may even be vague."""

May 1, 1946

By M. I. Copeland

The investigation of the iron-gadolinium phase diagram is part of a project undertaken by the Bureau of Mines and sponsored by the Atomic Energy Commission to investigate rare-earth alloys. Data from the investigation of the iron-gadolinium phase diagram revealed a single eutectic system with very limited terminal solubility and three intermediate phases. The eutectic point occurs at about 85 percent gadolinium, and the eutectic isotherm, which occurs at 850° C., extends from the compound Fe2Gd to 99-plus percent gadolinium. Very little solubility of the solid phases in each other was observed. The three intermediate phases, FegGd, Fe3Gd, and FeaGd, melt incongruently at peritectic isotherms at 1,320°, 1,150°, and 1,080° C., respectively. The crystalline systems of the three phases were determined as follows: FegGd, hexagonal; Fe3Gd, hexagonal or rhombohedral; and FeaGd, face-centered cubic. No lowering or raising of the alpha-gamma iron transformation at 910° C., the gamma-delta iron transformation at 1,388° C., or the gadolinium transformation at 1,262° C. was observed. The principal methods used in determining the iron-gadolinium phase diagram were melting-point determinations, thermal analyses, metallographic examination, and X-ray diffraction analyses. Melting, heat treating, and thermal analyses were conducted in a vacuum or under a helium atmosphere because of the avidity with which oxygen combines with gadolinium at elevated temperatures. A few hardness values were determined, but they had no part in the derivation of the phase diagram. No other mechanical properties were determined.

Jan 1, 1962