Search Documents

By Robert W. Decker

This report presents a survey of published novel coal cutting (mining) concepts and a brief discussion of each one. A preliminary evaluation follows which identifies promising concepts, emphasizing reduced dust generation and economic production potentials. The promising concepts are then studied more deeply and evaluated in more detail with recommendations given for further development action. The concepts recommended for further work include: Roan and Pillar Mining: Deep Cutting Continuous Miner Linear Cutting Rotary Head Miner Longwall Mining: Oscillating Continuous Water Jet Miner Deep Cutting Shearer

Jan 1, 1981

By Bruce E. Stauffer

The report recommends criteria for the design of safe surface mine haulage roads. Information relevant to road design at surface mine sites delineates vertical and horizontal alignment; subbase and surface materials; drainage; cross-slope, superelevation; runaway vehicle protection; and road and vehicle maintenance criteria. An appendix Is included which details the study methods used in compiling the final report information. A bibliography following the main text lists literature referenced for the report data and which is available as a valuable tool for use by individuals involved in haul road design.

Jan 1, 1976

By Russel Bohn

The purpose of this study was to evaluate the various techniques far mine roadway dust control. This evaluation included (a) the types of dust suppressants available, (b) the interaction of these products with the properties of the roadway surface, and (c) the costs and performance measures of the predominantly used dust suppressants. Over 30 products were identified having a wide range of effectiveness depending largely on the properties of the road base, subsurface, and wearing surface. The effectiveness of a dust suppressant was also found to depend on the application and maintenance procedures employed. As a result of this investigation five dust suppressants were identified s being predominant in the surface mining industry: Coherex, wetting agents, lignin sulfonate, water, and calcium chloride: An approximate cost-effectiveness analysis, limited by the lack of quantitative field performance data, showed that the five suppressants ranked in the order given above, with water being one of the least cost effective. This report also presents an analysis of applicable federal and state regulations.

Jan 1, 1981

By William E. Sopper

Heat-dried municipal sludge was applied to a barren burned anthracite refuse bank in 1974. Sludge was applied at rates of 0, 40, 75, and 150 dry metric tons per hectare" Ten species of trees were planted and five species of grasses and legumes were seeded for evaluation. One plot was also irrigated with sewage effluent. The 150 t/ha sludge application rate produced the best overall herbaceous vegetation growth response. The 40 and 75 t/ha sludge application rates produced the best tree seedling growth response. Foliar analyses for trace metals indicated no phytotoxity problems. Analyses of leachate water at the three-foot soil depth indicated that the sludge applications did not impair water quality. Results of the study indicate that treated municipal sludge can be used to revegetate land disturbed by mining activities without adverse effects on the vegetation or water quality.

Jan 1, 1978

By Thomas Novak, Robert Goldstein

The analysis of a machine-luminaire configuration is a time- consuming process requiring the construction of a machine mockup, installation of a designated lighting arrangement, and an extensive set of illumination measurements. This entire process, however, is well suited to computer analysis. By simulating the machine geometry and the characteristics of the desired luminaires, the incident light levels can be calculated at the required set of points. This Bureau of Mines paper presents a general description of the techniques involved in performing this simulation.

By Robert L. de Beauchamp

The Bureau of Mines designed a chlorination apparatus to prepare CrCl2 free of CrCl3 by the direct reaction of chlorine and chromium. Equipment and procedures were developed for routine preparation of 25-pound batch quantities of anhydrous CrCl2. Calcium, iron, nickel, and silicon impurities were in the 0.01 to 0.05 percent range, and all other impurities were below 0.01 percent.

Jan 1, 1968

By E. M. Murphy

Comparative data from ASTM method of test E-162 and large-scale trials in the Experimental Mine show that the flame-spread quality of brattice cloth and other ventilation control materials can effectively be evaluated by either method. Materials having a flame spread index of 25 or less, as determined by the simpler and more economical laboratory test ASTM E-162, do not present a serious fire hazard when used in coal mines.

Jan 1, 1972

By C. M. Romanowitz

This report deals with the factors which should be considered in evaluating a placer deposit and selecting a dredging system for mineral recovery. Overall dredging feasibility and the design of dredging systems are reviewed. Excavation methods, each with its advantages and disadvantages, are compared. Direct operating costs, both original and updated, of gold dredges with bucket capacities of 6 to 18 cubic feet are included. Costs vary with digging depth, changes in environmental conditions, and physical characteristics of the placer, all of which affect excavation rate and recovery. The costs, updated with appropriate indexes, should be used only as guidelines to evaluate potential dredging projects with similar characteristics. The relation of direct dredging costs to annual production is graphically illustrated by a family of curved envelopes that span dredge sizes from 2-112 to 18 cubic feet. A curve fitted to the data expresses the relation of direct costs to annual production for 151 dredge-years.

Jan 1, 1970

By S. Vennos

As a result of Synopsis 73-16 Dynadyne responded with an unsolicited proposal offering the Bureau of Mines to develop an ultra-low volume coal mine dust personal sampler. In the ensuing technical discussions the choice of a desirable volumetric rate became a focal point. While, the initial proposal was based on a volumetric rate in the area of 50 cc/min the Government expressed interest in a variety of mass flow rates ranging from 50 cc/min to 2000 cc/min. The physical characteristics such as weight, volume and configuration of a personal sampler are to a large extent - dependent on the operating volumetric rate. It became readily apparent that the optimum size of such an instrument as a function of volumetric rate was not known and that a study of the choice of optima was essential prior to beginning the development, Hence, the Government authorized a two phase approach to this project. Phase I was to include a Technical Evaluation Study of optimum characteristics in the range between 0. 1 to 2. 0 lpm. Based on these findings and in consultation with MESA personnel, the Bureau of Mines was to authorize the second phase that is, the development. Phase II, was to include the drawing of a set of performance specifications stating among others the desired operating volumetric rate. In this report, every effort was made not only to present the actual work done over the course of this development, but to reflect also our engineering "thinking" providing answers as to the "why" we preferred certain solutions over others. We believe that this added dimension is not only useful for the Government official evaluating this report, but also that the Government is entitled to it providing the official with an educational content useful in avoiding future costly repetitions of similar situations.

Jan 1, 1975

By Edward M. Kawenski

Float dust deposits in return airways in bituminous coal and lignite mines present a special explosion hazard. Research is in progress at the Bureau of Mines experimental coal mine to evaluate the degree of the hazard and to develop measures for preventing dissemination of dust into the ventilating air current. To determine the extent of this hazard prevailing in operating coal mines, 711 dust samples were collected in 50 mines located in the major coal fields of the United States. The mean quantity of coal and the incombustible content of the dust in the samples were determined. The term "float dust" is used to designate particles smaller than 74 microns in diameter (particles passing a No. 200 sieve) which have settled from the air current. Dust usually found in roadways and in working places is coarser than float dust, and is termed "coarse dust" (particles passing a No. 20 sieve). Variations in amount and incombustible content of coarse dust in a midwestern mine were studied previously.

Jan 1, 1963

By W. W. Adams

"The main purpose in the compilation of accident statistics is to reveal conditions that may result in injury to persons or property so that remedial measures may be applied. For practical reasons it is usually found necessary to restrict inquiry to conditions which actually have caused personal injury, and to omit those which nay, but have not yet, resulted in damage, Fortunately or unfortunately, there is a sufficient number of the former to indicate the existence of hazards so numerous as to require all of the attention which the industry can devote to the subject.Two years ago, the Bureau of 'mines, in cooperation with the National Safety Council, undertook an intensive campaign to obtain more complete and satisfactory information regarding mine accidents than had theretofore been available. Since 1911 the bureau had been receiving annual summaries from all companies operating metal mines, showing, in a general way, the number and causes of accidents that occurred during the preceding year and the number of men employed at the mines. Monthly summaries of fatal accidents at coal mines were received from the state inspectors, showing the number of deaths attributed to each of 22 main causes of accidents, Information for individual coal mines was not furnished.While this information, nation-wide in scope, is indispensable because it epitomizes the progress or retrogression in the industry as a whole, and serves as a background of specialized studies, yet certain classes of acci¬dents, for example, those that are more or less peculiar to specific districts or mines, require an analysis in greater detail than is possible on the sole basis afforded by the annual summaries.The need for more specific information was realized some years ago in the State of Pennsylvania in connection with the administration of the workmen's compensation law, The mining industry is well acquainted with the val¬uable studies of accidents, particularly nonfatal accidents, in the mines of that State being conducted by Mr. Rush N. Hosier."

Sep 1, 1924

By J. S. Megahan

This report covers the design, fabrication and testing of the first and second generation mechanical scaling bars for more safely removing loose rack from mine roofs and walls. Included are discussions covering a survey of mine conditions and presently used hand scaling bar types as well as the design, fabrication and testing of the first and second prototype.

Jan 1, 1982

By Philip E. Niebuhr

A procedure, which can be performed in the field by nonanalytical personnel, is given for sensitive spot tests for detecting tellurium or selenium. The expressed need of a field test for detecting small amounts of tellurium, which may be accompanied by relatively large amounts of selenium, has led to the development of this method. Tellurium search has been impeded by the lack of a satisfactory test from the standpoint of sensitivity and specificity. A quantitative laboratory method exists, but it is expensive and relatively laborious. Several other qualitative tests are known, but they require unstable solutions, which must be freshly prepared for use, and a greater variety of laboratory equipment. The particular advantages of the test described are its simplicity and the stability of the reagents required, there-fore is is well adapted for field use. Also, this test was found to be of practical use in the analytical laboratory when screening samples, thereby reducing analytical costs. The roughly quantitative interpretation of the results can save time by indicating the approximate size of the sample taken for a quantitative determination.

Jan 1, 1962

By Harold E. Marr

A simple algorithm is presented for processing digitized X-ray spectra obtained with a Si(Li) or Ge(Li) semiconductor detector coupled to a multi- channel analyzer. The simplified least-squares procedure is used to smooth out the statistical fluctuations in the spectrum by repeatedly fitting a quad- ratic equation to a predetermined number of channels and performing a traveling smooth across the spectrum. A logarithmic transform is applied to the raw data to minimize the distortion of the gaussian-shaped peak profiles. The efficacy of the technique is evaluated by observing the distortion of several gaussian-shaped peaks that have been subjected to the smoothing operation. The locations of maximums and minimums in the spectrum are predicted in the process as well as the values of the peak heights. The convolution integers from a least-squares fit of a quadratic equation are calculated as part of a FORTRAN subroutine. The building-block approach to computer programing in a small laboratory is discussed.

Jan 1, 1972

This report provides the results of an industrial engineering study that assessed the safety and efficiency of underground ore handling in U.S. metal mines. One of the primary findings of the study was the improvement needed in controlling muck size in the ore handling stream. Oversize ore causes much additional labor, creating work stoppages and is a principal cause of accidents in metal mines. This report includes data on block caving, back cut and fill room and pillar, shrinkage stoping, and sublevel stoping.

Jan 1, 1974

By K. P. Wang

The foundation of Japan's growing industrial and economic strength lies primarily in minerals, power, and technical know-how. Domestic raw material resources cannot supply domestic demand, and imports are indispensable. The Japanese are forced to acquire minerals and metals on a global basis, and their activities already have made an impact on international markets. A by-product of these efforts is the development and expansion of mines in many parts of the world to supply Japanese requirements. Japan now has a surplus capacity to produce finished products for consumption and export. Tradition-ally, domestic deficits in minerals have been met by importing crude materials. Because of the rising demand, however, the time has come when semi finished products as well as crude minerals are required. While the domestic market is the mainstay for Japan's industrial products, expanding export markets are essential for balancing trade and for providing economic prosperity and higher living standards for the Japanese people. Japan has a long history of mineral and industrial development, and the best in modern practices abroad has been adopted and modified for use under Japanese conditions of smaller enterprises, cheaper labor, and a more closely knit society. Generations of industrious workmen, technicians, and business-men have been trained in industrial occupations. Devastation of war temporarily slowed progress, but at the same time provided the opportunity for reconstruction, modernization, rationalization, and expansion. The Japanese excel in small and medium-sized operations, but they also have mastered large-scale production. Management is aggressive, practical, and strongly imbued with the concepts of effective utilization of resources. Integrated operations, diversification of facilities, intense competition among concerns in the domestic market, and close cooperation in foreign activities characterize Japanese industrial policies. Available capital has been utilized up to the limit for the establishment of mineral and other industrial facilities at home and abroad. Technology, machinery and equipment, and transport services have been exported along with venture capital, and funds have been advanced against future delivery of foreign raw materials. The Government has been restrained in regulatory functions and has provided technical services to private industry. Thus, Japan's technological foundations are secure, management practices are efficient, and government has stimulated production. The future outlook is bright for the continued rapid growth of mineral and other industries in Japan. Already supreme in Asia in per capita output and living standards, Japan steadily is gaining on the European countries. Steel production has overtaken the United Kingdom and is pressing the level in West Germany. Consumption of fuels and power is expanding at a rapid rate. Construction activities are booming. Japan has built up medium-sized non-ferrous industries. Its ability to produce the exotic metals needed in the nuclear space age is well established. Since Japan makes a great variety of mineral products, her overall posture in mineral extraction and processing is strong. Primarily as a result of intensive efforts in the mineral and other industrial fields, Japan is emerging in world markets as a serious competitor to all industrialized nations.

Jan 1, 1962

By Robert S. Schechter

This report describes the development and application of PHASEQ/FLOW, a geochemical flow simulator capable of describing the dynamic changes in chemical composition of an aqueous solution during flow in a permeable medium. The solution components can react through intraaqueous reactions, redox, precipitation, or dissolution. The assumption of local thermodynamic equilibrium ensures maximum generality with respect to the number of species and components possible; however, the fluid flow itself is limited to one-dimension. The report describes several applications: generic batch equilibria, flowing equilibria, uranium roll-front deposition, and roll-front leaching.

Jan 1, 1985

By R. A. Cummings

Certain roof shales in coal mines deteriorate upon exposure to the atmosphere, causing difficulties in the mining operations and adding to the cost. This report presents the results of both field investigations, in a West Virginia mine, and laboratory studies on the effects of atmospheric moisture on roof shales. Based on these observations a conceptual procedure is presented on how shale deterioration might be predicted during exploration, and guidelines are given as to how air tempering or conditioning chambers may be designed to reduce moisture effects. Recommendations for further studies are included. An annotated bibliography of the literature constitutes the second volume.

Jan 1, 1981

By C. E. Hennig

On January 1, 1961 there were 311 petroleum refineries in the United States with a total crude-oil throughput capacity of slightly more than 10 million barrels per day, according to the Bureau of Mines' annual survey. Compared with a year ago, this represents net increases of one in the number of plants and 109 thousand barrels per day in total capacity. Contributing to this increase was the completion of two new plants, one in Hawaii and another in Michigan, during the year. At the beginning of 1961 the industry was building facilities which will increase this overall crude capacity by 36,500 barrels per day. As part of its building program, it was also replacing 329,000 barrels per day of its present capacity. Of the total 10 million barrel per day installed capacity, the industry reported 380,000 barrels per day as being shut-down on January 1, 1961. This included 11,500 barrels per day considered inoperable without extensive reconditioning.

Jan 1, 1961

By Claude W. Sill

In the usual volumetric determination of uranium, the solution containing uranium is reduced in a Jones reductor, yielding a mixture of trivalent and tetravalent uranium; the trivalent uranium is oxidized to the tetravalent state by bubbling a stream of air through the solution. The resulting solution of. Tetravalent uranium is titrated with a standard oxidant, generally sulfatoceric acid, dichromate, or permanganate; It seemed likely that the, same general procedure could be used in determining semimicro quantities of uranium if the conditions affecting the variables involved were understood more clearly than at present. In the method described below, the use of ferric sulfate to oxidize tetravalent uranium allows the titration to be made at room temperature in an essentially colorless solution with sulfatoceric acid. The latter oxidant its turn permits the use of the very stable indicator, ferroin, with its sharp color.., change and exactly reproducible blanks. Solutions of uranyl sulfate were prepared by diluting a stock solution that had been standardized gravimetrically according to the method of Lundell and Knowles (8).3/ Solutions of sulfatoceric acid were prepared according to the directions of G. F. Smith (12) and were standardized against arsenic trioxide in the presence of osmic acid according to the directions of Gleu. The cerium solutions were stored in 18-liter carboys fitted with siphon arrangements so that the bottles did not need to be opened and protected from light in a dark cupboard. Under these conditions, even the 0.01 N solution changed by less than 1 part per thousand over a period of about 6 months.

Jan 1, 1952