Search Documents

By P. G. Pigott

This Bureau of Mines laboratory research demonstrated that building bricks meeting ASTM specification C62-66 for grades SW and MW of FBS-type bricks can be produced from waste copper mill tailings. Waste tailings from accumulations at Magna, Utah, Anaconda, Mont., and Hayden, Miami, and San Manuel, Ariz., were dry-pressed into bricks, and the products were tested in accordance with ASTM Designation C67-66 on sampling, and testing of brick. An evaluation derived from pilot-plant production of similar brick at the Coal Research Bureau of West Virginia University indicated the production cost to be about $34 per 1,000 bricks. Utilization of such mill tailings on a commercial scale would eliminate the need for digging new pits for brick raw material production, conserve natural resources, and simultaneously remove potential sources of air pollution.

Jan 1, 1971

By John H. Soule

Although known since 1902 , the Capitan iron deposits have not been mined mainly because of the low grade of the ore . A small amount of exploratory work carried on at an early date was reported . C. E. Johnson , district engineer of the Bureau of lines for New, Mexico , visited this propert , and as a result of preliminary sampling and mapping by the Bureau3/ and the Federal Géological Survey , an exploratory project was conducted during March , April , and liay 1944. Further mapping and logging of the vagon -drill samples was done by V. C. Kelly , geologist , of the Survey .

Mar 1, 1947

By Marshal Scherba

Coal seams approximately 7 feet, 9 feet and 20 feet thick at depths of 250, 600 and 1,000 feet respectively were detected using high resolution seismic reflection techniques. Investigation of seismic profiles indicates that good data are required to delineate faulting with only 20 feet of throw but that faulting with 50 feet of vertical displacement can be detected with poor data. Data acquired from dynamite charges fired in water saturated media were clearly superior to that acquired using charges dry tamped in 10 and 20 foot holes.

Jan 1, 1977

By Jose P. T. Agapito

Several underground coal mines currently operating in the Beckley District of West Virginia are experiencing serious roof and floor problems. A significant portion of the estimated two billion tons of coal resources may be lost as a result of these ground control problems. Preliminary studies by the Bureau of Mines indicated that these problems are due in part to a high horizontal stress field. During this contract study, a field program was conducted to quantify the horizontal in situ stress. A total of 14 overcoring sites (using the Bureau of Mines strain-relief overcoring technique) in five mines were drilled producing 53 data sets. Analysis of the data was done to provide in situ horizontal stresses for each of the five mine, and for the district as a whole. Stress data indicate horizontal stresses far in excess of that predicted by theory and in some cases, up to six times the estimated vertical stress. In addition to the field testing, a detailed computer modeling study was conducted using finite element and boundary integral (displacement discontinuity) methods. Verification of in situ stresses was obtained by the models and analysis of various development geometries, mining methods and remedial techniques were conducted. Recommendations for reducing ground control problems and future studies are presented.

Jan 1, 1980

By Magnus Persson

ISO8662-4, “Hand-held portable power tools - Measurement of vibrations at the handle - Part 4: Grinders” is under revision. The new revision shall harmonize ISO 20643 “Mechanical vibration - Hand-held and hand-guided machinery - Principles for evaluation of vibration emission” which, among others, requires measurements in three directions and declared values related to the upper quartile of real-use vibration. To get the most suitable test method, a round robin test was made for evaluation of the two test methods proposed by the ad-hoc group working with this standard revision. Methods Seven laboratories measured the vibration from four grinders of different sizes, with and without autobalancing units. The laboratories come from universities, health & safety laboratories and grinder manufacturers. Two measurement methods are evaluated with respect to repeatability and reproducibility: 1. Grinding on a well-defined mild steel bar with depressed center wheels according to detailed test instructions. The test sequence starts and ends with 10 seconds of running the grinder in the air, when measuring the unbalance contribution to the vibration coming from the unbalance of the grinding wheel. Between these runs the average vibration during 60 seconds of grinding is measured. Three operators do five grinding tests per grinder. 2. Measurements using an aluminum unbalance disc similar to the one defined in ISO8662-4. Each operator runs the grinder four times, between each run the unbalance is moved 180 degrees to avoid variations caused by the play between the test wheel and the spindle. The averaging time is 10 seconds. Each grinder is tested by three operators. Repeatability is the spread within a lab between operators and over short time period for one machine and reproducibility is the spread between laboratories and over longer time periods for one machine. Instrumentation and transducer location are chosen according to ISO8662-4 and circulated test instructions. Results Both the repeatability and reproducibility is poor for the real grinding test, see figure 1. The coefficient of variation for repeatability is approximately 40% higher for the grinding test and the coefficient of reproducibility is 60% higher for the grinding test than for the unbalance disc test.

Jan 6, 2006

By Roy L. Wilfong

The thermal decomposition of the ammonium sulfate, carbonate, nitrate, oxalate, and sulfate salts of praseodymium, neodymium, and samarium was investigated thermogravimetrically in the temperature range 25° to 1,500° C. Each salt was decomposed at a heating rate of 2.5° C, per minute. The pyrolytic sequences have been identified and the temperatures of formation of inter-mediates, the minimum oxide formation temperatures, and values for loss on ignition have been determined. The nonstoichiometric ranges between Pr6011 and Pr203 and the extent of these ranges have been determined for oxides derived from the carbonate, nitrate, and oxalate salts of praseodymium. The alum and sulfate salts of praseodymium produced the sesquioxide without forming the intermediate non-stoichiometric oxides. The temperature limits of formation and regions of stability for the alums and sulfates were better defined than were those for the carbonates, nitrates, and oxalates. The minimum oxide formation temperature increased in the order of samarium, neodymium, and praseodymium irrespective of the anion.

Jan 1, 1962

By Jonathan E. Ludlow

A field test was conducted to demonstrate and quantify the relationship between deep cutting and the creation of airborne respirable dust for longwall mining With a double-ended ranging drum shearer. The testing program was carried out on the 3 North longwall of North American Coal Company's Quarto No. y mine in Claringten, Ohio. Continuous recordings of the dust levels were made at both the midface and tail ate areas. Data were collected during 27 shifts during which time 81 complete mining, cycles took place. Both drum speed and the number of picks per line were varied systematically during the testing program to alter the depth of cut while the production rate was held constant by maintaining a constant haulage speed. The test results indicated that at the midface position, airborne respirable dust was strongly dependent upon the depth of cut as influenced by both the drum speed and number of picks. Drum speed had a much stronger effect than number of picks over the experimental range, since a halving of drum speed reduced dust levels by approximately 60 percent while removal of every other vane pick resulted in only a 2.1 percent reduction at constant production. At the tailgate position, however, neither effect was strongly apparent. A tendency for the slower drum speeds to he associated with reduced power consumption and higher haulage speeds (and therefore production rates) was also noted. It is recommended that longwall operators oper¬ate at the lowest available drum speed wherever possible.

Jan 1, 1981

By William C. Hood

A leaching column technique that produces effluent similar in quality to coal mine drainage in the Eastern Interior Basin has been developed. The columns are charged with 1000 grams of crushed overburden and cycled through the leaching process once a week for twelve weeks. Inter-relationships among the important chemical constituents are very similar to those present in actual mine drainage waters, but the overall concentrations of ion are more dilute in the leachates. Multiplying the leachate concentrations by a factor of 4.5 gives values similar to mine waters. Available data suggests that each of the leaching cycles represents about three years of natural weathering, so that the leaching technique can predict the evolution of the mire drainage water over a time span of nearly 40 years. Use of the leaching technique with drill core samples should provide a method of approximating mine drainage quality in advance of mining and should be quite useful in identifying potentially toxic units in the overburden. However, the results should he considered to be a 'worst case' situation because the technique' does not consider the effects of reclamation.

Jan 1, 1984

By Sheridan J. Rodgers

Improved methods of dust control in the metal and nonmetal mining industries were studied. Preliminary dust surveys were made at selected mines and three mines were chosen for additional studies. Dust control effectiveness was evaluated using full shift gravimetric sampling and GCA Dust Monitor readings. Analyses for free silica content and particle size distribution were conducted. A belt washing system which was used to control dust at a transfer point was evaluated. The average reduction of respirable dust was 48% and the average reduction of total dust was 78%. The belt washing system not only maintained the work place within compliance but reduced maintenance problems along the beltway by 90%. Exhaust ventilation at a crusher was evaluated for control effectiveness. Ventilation along with operation of the crusher control room under slight positive pressure, maintained the work place within compliance. An exhaust ventilation system was designed for use at an underground rotary dump. Although the system was not installed or evaluated, details on the design are given. High expansion foam was used at an ore chute in an attempt to control dust at the draw point and loading point. Results indicated that foam did not effectively control dust.

Jan 1, 1978

By John L. Ellenberger, Gabriel S. Esterhuizen

Observations of pillar conditions in limestone mines showed that the presence of weak bands in the limestone can result in pillar damage at stresses that are lower than one would otherwise expect. The objective of this National Institute for Occupational Safety and Health study was to investigate the mechanism of failure caused by the presence of weak bands by using a series of numerical models based on realistic physical properties. The effect of the weak bands on pillar strength was also investigated by developing a series of pillar models with different width-to-height ratios and determining their strength by simulating a servo-controlled loading condition. The material properties of the bands and the limestone were varied and their effects on pillar strength were determined. Model results demonstrated failure development similar to the pillars observed in the field. The weak bands were seen to develop tensile stresses in the limestone as they extrude under increasing stress. The limestone fails in tension at a much lower stress than its expected uniaxial compressive strength. The results showed the load bearing capacity of the pillars can be reduced significantly by the presence of multiple thin weak bands. The degree of strength reduction is largely dependent on the compressive strength, the frictional resistance and the thickness of the weak bands. Single weak bands do not affect pillars as severely as multiple bands. However, the model results show that a single thick weak band, which comprises more than about 2 percent of the pillar height, can cause a significant reduction in pillar strength. The weakening effect of the bands become less severe as the pillar width-to-height ratio is increased. Field observation of spalling and failure associated with weak bands in limestone pillars show that the failure mechanism in the models resembles the observed failure. The model results provide insight into the important factors affecting pillar strength in the presence of weak banded materials.

By C. M. Harrer

This paper describes the location and general features of iron occurrences in Colorado. Most of the deposits were examined; many are in forested and mountainous areas at altitudes of 5,000 to 13,700 feet. Iron is known to occur in 30 counties of western Colorado. Transporting the ore to market is a handicapping economic factor involving long truck and railroad hauls; the nearest purchaser of smelting ores is the Colorado Fuel and Iron Corp., at Pueblo, Colo. When the ore can be sold locally for special purposes and at higher prices than can be obtained at iron smelters, small-scale operations can supply that market.

Jan 1, 1959

By B. J. Moore

This publication contains analyses and related source data for 675 natural gas samples from wells and pipelines in 24 States and 5 foreign countries. The samples obtained and analyzed during calendar year 1980 are included in tables 1-4. Those samples included in tables 5-7 were collected during the years 1960 through 1979. However, permission to publish the analyses of those samples was not given until the past year when the operators were again contacted to seek release of the information. All of these samples were collected as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4862 and 576. The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the general public. Twenty-two previous publications have presented the results of 12,152 gas analyses made prior to 1980. The first three, Bulletins 486,' 576,5 and 617,6 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1980. The other

Jan 1, 1981

In the interest of safety in underground coal mining, the Bureau of Mines recommends: 1. That doors used to control ventilation (a) Shall be installed in pairs to form air locks, (b) Shall be self-closing, (c) Shall not have latches or other devices for holding them open, (d) Shall be constructed and maintained to prevent excessive air leakage through or around them, (e) Shall be fire resistant. 2. That wherever practicable the use of doors shall be limited to development openings. The Mine Safety Board is of the opinion that the best practice in coal-mine ventilation makes use of a split system employing overcasts or undercasts with doors limited as far as feasible to development openings. The distance between air-lock doors on haulageways should be sufficient to accommodate a trip or train of maximum length. Where auxiliary doors are installed to control ventilation during emergencies, they should be so placed that they can be utilized readily in case of damage to the air-lock doors.

Jan 1, 1938

By H. C. Fuller

This paper discusses 105 production runs at Boulder City, Nev., in which titanium metal was made in 200-pound batches. It describes the equipment and techniques used in preparing raw material, the reduction process, and the removal of the reaction mass from the reaction vessel. Also, some data on man-hour requirements are presented. The main emphasis was on producing ductile-grade titanium and developing a standard procedure for obtaining a consistently pure product. Some departures from techniques used before were found to be desirable. The most important of these was the use of a sealed room with a controlled dry atmosphere in which the reaction vessel was opened and the reaction mass removed. This minimized the moisture taken up by the magnesium chloride in the reaction mass, and it could be purified successfully by vacuum distillation. Using the dry room also made it possible to leave al-inch shell of the reaction material on the walls of the vessel, which lowered the iron contamination and eliminated the labor and time-consuming job of cleaning the vessel after each reduction. Another change was lowering of the temperature during reduction to 750° C. instead of 850° C. This was found to give good results more consistently. The first poke to break the crust during reduction was eliminated, as it was found to be unnecessary and only added more work and was another possible way of introducing air. A rotating feed arm was installed in the reaction vessel to distribute the titanium tetrachloride over a larger area and, thus, prevent local overheating. The process, conducted in a batchwise manner as described and followed by good purification and fusion, produces a metal adequate in quality for nearly all purposes.

Jan 1, 1952

By Ren G. Dong, Thomas W. McDowell, John Z. Wu, Chris Warren, Dan E. Welcome, Chun L. Dong

Hand forces are important factors for risk assessment of hand-arm vibration syndrome (HAVS).1 Grip force is one of the most important force components in the operation of powered hand tools. A considerable number of studies on grip force have been reported. It is well known that the grip force applied on a cylindrical handle is not uniformly distributed on each axis across the center of the handle cross-section.2 Therefore, maximum and minimum orientations of grip force exist around the handle. Such orientations have not been clearly identified. In a recently proposed international standard (ISO/CD 15230, 2005),3 it is stated that “the direction of the main gripping force is generally parallel to the z-axis defined in ISO 8727.” 4 This assertion is questionable, and further examinations are required. The objective of this study was to establish a fundamental theory on the distribution of the grip force around cylindrical handles. Methods As shown in Fig. 1, the grip force is defined as a vector composed of normal and shear components (FN & FT) in this study. Fig. 2 shows the hand coordinate system defined in this study, together with the ISO systems.1,4 Based on this novel grip force definition, we derived four fundamental properties and a theorem. More significantly, we formulated a novel hypothesis: similar to Mohr’s circle of stress, the normal and shear components can be represented approximately using an ellipse on the plane of the two force coordinates, as shown in Fig. 3. The maximum and minimum grip normal forces are termed as the first principal grip force (F1) and the second principal grip normal force (F2), respectively. Their corresponding orientations are termed as the first principal grip angle (a1) and the second principal grip angle (a2). A series of experiments were conducted to test this hypothesis. Twelve

Jan 6, 2006

By Howard B. Hamilton

Laboratory performance of mercury filled current limiting devices (CLD) used for high speed switching of DC circuits (600 volts and below, up to 1000 amperes) using a system involving a parallel connected vacuum switch with CLD and an additional series connected vacuum switch was verified in USBM Contract #HO 357079. This report details analytical work and field experimental tests to predict and control voltage surges associated with the high switching speed associated with the switching system. It also details tests conducted to demonstrate the fault current limiting ability of the CLD. Problems associated with designing a fault current limiting system are discussed.

Jan 1, 1978

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and the results are described in this report.

Jan 1, 1983

By J. C. Engel

Recent innovations in mine safety include the use of mercury vapor lamps for mine vehicle illumination. Such lamps, however, extinguish whenever the line voltage at the machine momentarily sags or is interrupted. The lamps must then cool for several minutes before they will restart. By supplying reduced high frequency power to the lamps from an auxiliary source, it is possible to maintain ionization in the arc tubes preventing the lamps from extinguishing. Essentially an auxiliary high frequency supply, the keep alive system provides additional power to the lamps automatically whenever the lamps are in danger of dropping out. The system can also provide the operator with the ability to dim the lamps at will for periods of up to three minutes by simply interrupting the 60 Hz power to the conventional ballasts. Each unit, housed in a steel explosion proof enclosure with a volume of approximately 0.6 ft3, is capable of servicing up to six 175 watt H-39 mercury lamps and two 100 watt H-75 reflector flood lamps. A total of 16 units were produced for the USBM under this contract and its extension.

Jan 1, 1979

By J. L. Thompson

The U.S. Bureau of Mines conducted a water-jet-studies program using a single-bit, in-seam test unit to determine effects of a moderately high-pressure (up to 10,000 psi) water-jet-assisted cutting system on rock weakening. The in-seam test unit was used to obtain cutting force data in tangential, normal, and side force directions. Conical continuous miner and radial longwall miner bits were used to penetrate test samples of coalcrete, Berea sandstone, and Indiana limestone with unconfined compressive strengths of 4,600, 8,000 and 10,000 psi, respectively. Depth of cut in the coalcrete tests was 1 in, with 2-in cut spacing (2:1 ratio). Because of cutting equipment and instrumentation limitations, the Berea sandstone and Indiana lime-stone were cut using a 0.5-in depth of cut and 2-in spacing (4;1 ratio). Bit velocity was maintained at 25 ft/min for both bits. Each specimen and bit type was tested using 0.3-, 0.6-, 0.8-, and 1.0-mm-diam nozzles and water-jet pressures of 2,500, 5,000, 7,500, and 10,000 psig. Water-jet-assisted cutting decreased average resultant conical and radiallongwall bit cutting forces 6.4 and 8.4 pct in coalcrete, 5.5 and 1.4 pct in Berea sandstone, and 2.0 and 5.5 pct in Indiana limestone. Slight reductions of power requirements resulting from water-jet assist were ascertained during these experiments.

Jan 1, 1989

By George W. Huseman, W. D. Mcmillan

"INTRODUCTION Feldspars represent one of the most abundant groups of minerals and constitute nearly Go percent of the material contained in the igneous rocks. They are grouped in a series of related aluminum silicates with varying amounts of potash, soda, and lime. .Approximately 85 percent of the feldspar produced in the United States is used as a flux in the production of glass, pottery, enamel and sanitary ware, brick, and tile. Notwithstanding the abundance of feldspar in the earth's crust, the only deposits that are worked to any extent are the pegmatites or coarsely crystalline dikes where natural segregation of the constituents facilitates recovery of the feldspar with a minimum of free quartz, mica, tourmaline, garnet, and other iron-bearing minerals that are detrimental in most ceramic industries.Although there are three glassplants and numerous other ceramic industries in Texas, all of the feldspar used in these plants is from other States. In the Llano region of central Texas, however, there are numerous coarse pegmatite dikes consisting primarily of feldspar and quartz in ratios up to 3 to 1. One of the more important of these dikes is the Badu Hill deposit in Llano County, Tex., which was first described by Carl Chelf 4/ in 1942. Following an examination of the deposit by W. D. McMillan, engineer in charge of the Texas field office of the Bureau of Mines, in January 1946, a proposal was made to investigate the deposit by core drilling in cooperation with the Department of Ceramic Engineering, University of Texas. This report presents the results of the cooperative investigation, which was begun April 24, 1946, and completed May 17, 1946."

Jul 1, 1947