Search Documents

By Sam G. Demou

Drag bit cutting tests were conducted chiefly to determine bit forces encountered in rock types representing a range of compressive strength and hardness and thus enable the design engineer to estimate a continuous miner's performance in a range of rock types. Testing was carried out on the Bureau of Mines uniquely designed, instrumented rock cutting device (RCD). This device can make 3-ft-long cuts at various depths and speeds to approximate full-scale drag bit cutting by continuous miners. Point attack and cutter bits were tested on four rock types ranging in compressive strength from 7,200 psi (trona) to 29,600 psi (Valders white rock). Cutting tests were made at depths up to 1 in and speeds up to 70 in/sec. Data included normal and cutting forces, groove depth, groove width, and weight of rock broken. The effect of varying the cutting speed was determined, and specific energies were calculated for the various conditions. The bit wear was also observed. For the rocks tested, compressive strength and hardness are good indicators of forces, specific energy, and wear encountered. Results, especially bit wear observations, show the possibility of extending continuous miners, already being used in trona, to Indiana limestone (10,000 psi). Rapid bit deterioration precludes use in Tennessee marble (16,800 psi) and Valders white rock (29,600 psi).

Jan 1, 1983

Background: Frictional ignitions continue to be a problem facing the U.S. underground coal mining industry. Many methane igni-tions are associated with the impact of mining machine cutter bits on quartzitic material (e.g., sandstone) during the coal-cutting process. Most ignitions result in small methane-air fireballs often only a few feet in size and limited to the cutter head location. However, under certain conditions, frictional ignitions can lead to larger methane explosions and/or fires with the potential for causing serious injury or death to the mining machine operator and other nearby miners. The requirements for a frictional ignition are a flammable volume of methane-air and an ignition source. This source is usually the hot streak caused by the frictional impact of the mining bit on hard rock, and the frequency of occurrence increases with increased bit wear. Another possible ignition source is the fric-tional impact of rock on rock during a roof fall.

Mar 1, 2008

By Donald W. Mitchell

Research shows that water neutralizes the explosion hazard of coal dust when present in sufficient quantity and when intimately mixed with the dust. The quantity of water required to neutralize coal dust and coal-rock dust mixtures is about equal to the limiting moisture adsorptive capacity of the dust; the adsorptive capacity increases with increase in the fineness and volatile content of the coal. Pools of water or high atmospheric humidity do not reduce the explosion hazard. Although wetted dust is less dispersible than dry dust, poor dispersibility cannot be relied on as the sole safeguard against explosion. Dust mixtures that contain water in excess of their limiting adsorptive capacity are dispersed and ignited by severe initiation sources. Pure coal dust adsorbs water with difficulty and retains water poorly; adsorption and retention is increased by the addition of rock dust the coal; the rock dust agglutinates wetted coal and assures that incombustible is present should drying occur. Therefore, it is advantageous to rock-dust wet areas in bituminous coal and lignite mines. When coal-rock dust mixtures are wetted and subsequently dried, the explosion hazard is about the same as for dust which was not wetted.

Jan 1, 1962

By E. D. Calvert

Molybdenum has been successfully cast into static and rotating molds in conventional equipment used for casting titanium and zirconium. Melting was accomplished by using an arc potential of 36 to 40 volts with a current of 10,000 amperes. Pouring efficiency, after a skull had been formed in the crucible, averaged 70 percent. Techniques are described by which four successful castings were made. Tensile properties on specimens cut from one centrifugally cast tube averaged: Tensile strength, 39,800 p.s.i.; yield strength (0.1 pct. offset), 35,300 p.s.i.; elongation, nil; reduction in area, nil; impact strength, 2 ft.-lb.; hardness DPH (diamond pyramid hardness) 180. Mold reaction was not evident in shapes cast in machined graphite. This was not true, however, for rammed graphitic-base molds.

Jan 1, 1960

By J. A. Bartol

A survey was made of accident data and operating practices related to overloading and uneven load distribution on haulage trucks in noncoal open pit mines. Safety and economic aspects were analyzed. A bibliography of the literature was prepared. Review was made of available or projected systems for weighing or load indicating that might be applied to haulage trucks. A model specification was prepared for an overload detection system. Several promising systems for overload detection were identified. One was installed and tested briefly in a 170-ton rear dump truck in a copper surface mine.

Jan 1, 1982

By David C. Uhrin

Two improved methods have been developed to transfer microfilmed mine maps to suitable base maps showing surface features. The methods provide for (1) positioning and orienting maps; (2) merging adjacent maps; and (3) plotting maps at a common scale. One method produces an overlay mosaic of mine maps using an Integrated camera-processor. This photographic method shows the details of mine workings and is most useful for specific limited-area projects. In the second method, outlines of mine maps are digitized, manipulated, and plotted as overlays using a computer. This computer method can plot mine outlines and spatially index large numbers of microfilmed maps. Microfilmed mine maps used in this Bureau of Mines study are on file in the Mine Map Repository of the Eastern Field Operations Center. The base maps are U.S. Geological Survey 7.5-minute topographic maps. The demonstration area is located in the New Kensington East and West quadrangles, Pennsylvania.

Jan 1, 1977

By R. L. Zick, J. D. Byars, T. P. Mucho

Recently, a large Pittsburgh seam longwall mine was nearing depletion of a major portion of its current reserves and had begun to develop in a different direction from its original portal area to access additional reserves. This meant that a large area of the mine would be abandoned and sealed. However, continued use of the original mine portal area required that the water accumulating in the abandoned mine would eventually need to be pumped to the surface. This would be in addition to the discharge water associated with the new portion of the mine. Several pumping and sump options were investigated to handle the quantity and quality of the anticipated discharge water. This paper describes some of these options, their advantages and disadvantages, and the final engineering decisions. Some problems and unanticipated outcomes, as well as the eventual solutions are discussed, including: (1) estimates of pump requirements, (2) water pool size, (3) eventual water quality, (4) anticipated inflows, and (5) integration into the overall mine water system.

By Robert H. Peters

Groundfall accidents have been the leading cause of fatalities in the underground coal mining industry for many years. Statistics from the Mine Safety and Health Administration (MSHA) indicate that approximately half of the victims of these fatal accidents were in an area where no devices had been installed to support the mine roof. This report was prepared by the U.S. Bureau of Mines to provide guidance to operators of underground mines concerning the use of techniques that may help to keep miners from going under unsupported mine roof. The report is divided into two major sections. The first section reviews the findings from several areas of empirical research pertaining to strategies for convincing employees to avoid unsafe acts and/or adopt self-protective behaviors. The strategies are (1) incentives and feedback, (2) disciplinary actions, (3) training (primarily fear communications and behavioral modeling), and (4) nondirective techniques. This literature review has a broad focus and should be helpful in making decisions about how to encourage a wide variety of types of self-protective behaviors. The second major section of the report presents an analysis of each strategy's potential for keeping miners away from unsupported roof.

Jan 1, 1991

By E. W. Felegy

Since 1920, the Bureau of Mines and, other agencies have conducted numerous investigations of methods of communication for use in mines in times of disaster or emergency. The results of these investigations have been reported in various publications (3, 4; 5, 6, 8, 9, 10, 11, 12, 13, 14, 15, 16). In November 1944, the Bureau of Mines resumed the study of emergency underground communications. Until March 1946, the program was directed toward reexamining methods of underground communication that indicated possibilities of success. Since April 1946, the principal interest of this investigation has been in methods of application of radio to communication in mines, low-frequency radio seeming to offer the most promise as a successful method of emergency mine communication. Results achieved in reexamining other methods and in the investigation or the application of low-frequency radio between November 1944 and September 1946 were reported previously in a publication entitled "Some Studies on Emergency Mine Communications".

Jan 1, 1948

By Foster Fraas

One of the lithium minerals most widespread in the earth's surface is spodumene (Li2O-A1203-4Si02) a lithium aluminium silicate. For some time, deposits of this mineral were known to exist in the Black Rills of South Dakota, but it was only quite recently that Hess4/ pointed out the great magnitude of the low-grade e deposits it s in North Carolina. The theoretical lithia (Li20) content of spodumene is 8.04 percent. The only other minerals with such high lithia content are the phosphates, but these occur only in pockets and are not in extensive deposits5/. Actually, however, the lithia content in spodumene is never found to be this high, being nearly always below 7 percent for the pure mineral, and part of the lithia is apparently replaced by other alkalies.

Jan 1, 1937

By Charles C. Boley

High-volatile A bituminous coal from the Allen mine, Las Animas County, Colo., blended with char produced from the same coal yielded accept-able metallurgical coke in a 500-lb movable-wall test oven. Nineteen experimental runs were carried out using several concentration levels of two different chars, 5.6 and 19.6 percent volatile matter, produced by entrainment carbonization of the base coal. With the higher-volatile char, an acceptable coke was produced at a 22.5-percent concentration; the lower-volatile char did not produce an acceptable coke at the concentrations investigated.

Jan 1, 1972

By George J. Conroy

This Bureau of Mines report summarizes the results of a study of mine inspection records covering 2,200 mining installations over a 3-year period ending December 1974. Tables show the relative frequency of violations of certain provisions of the Coal Mine Health and Safety Act of 1969 in particular areas of concern, such as circuit breakers, grounding, and permissibility. Examples of past use of the data and analyses are presented.

Jan 1, 1976

By John A. Breslin

The Bureau of Mines measured respirable dust in coal mines by means of multiple dust samplers worn by persons moving about the mines. The measurements were made primarily to evaluate the effectiveness of certain dust-control techniques; however, for this report, the data have been analyzed to determine the precision of the personal dust-sampling measurements. A total of 68 sets of measurements were available from multiple personal samplers. The measured dust masses were less than 1.0 mg because the sampling times were short. The coefficient of variation calculated from these data was 18.5 pct, compared with coefficients of variation ranging from about 10 to 30 pct, which were calculated from the most precise and extensive data available for fixed-point dust measurements made in coal mines. From this comparison, it is concluded that dust samplers worn by personnel are as precise as fixed-point samplers in measuring respirabe coal dust; the wearing of the samplers by someone moving about a mine does not contribute significantly to the variation in measurements made with these instruments.

Jan 1, 1983

By B. W. Gandrud, G. D. Coe

"INTRODUCTION The Bureau of Mines, United States Department of the Interior, with the cooperation of the University of Alabama and coal producers of Alabama, is making a series of washability studies to obtain technically and commercially important data from the productive coal beds of the State. Based on the system followed in these studies, this report consists of screen-sizing and sink-and-float data on the America and Pratt beds at Gorgas, Ala.SAMPLING AT THE MINESAlthough operations were discontinued in 1929, the accessible openings of the old Gorgas mines of the Southeastern Fuel Co. made possible the taking of samples from the America bed at three openings and from the Pratt bed at two openings. A sample was taken from the America bed at the Klondyke opening; a second was taken about 1 rile south of the Klondyke at the Musgrove America opening, and a third sample was taken about 1-1/2 miles south of the Musgrove-America at the Cricket Lodge opening. A sample was taken from the Pratt bed at Musgrove-Pratt No. 1, which is about 3/4 mile east of Musgrove-America, and a second sample was taken at Musgrove-Pratt No. 2, which is about 3/4 mile west of Musgrove-America. The samples ranged in weight from 1/2 ton to 1 ton and were equivalent to approximately a 2-ton sample from each bed. Figure 1 shows sections of the beds at the places sampled.In addition to the samples for washability study, a seam sample for analysis was taken at each of the places sampled. So as to give a representative seam sample for each of the two beds, these samples were combined in the laboratory in proportion to the thickness of the bed at the places sampled."

Jul 1, 1939

By Robert D. Perry

This report describes methods of reclaiming abandoned or inactive tailings ponds and dams. The investigated sites were selected tailings deposits adjacent to metal mines in the southwestern United States and the Pacific Northwest. The basic data developed for each site consisted of the following: a review of existing literature: a site visit that included sampling of the tailings and surrounding materials; laboratory and engineering studies; and development of reclamation plans. Laboratory tests determined the gold and silver content of each tailings deposit and the chemistry of the tailings and surrounding materials. Reclamation plans that include approximate costs were developed for five tailings deposit sites. These ranged in size from 52,000 to 103,000,000 tons. Our conclusions on the remining potential of each site are based on the tailings assay and other technical data. This study concludes that remining as a reclamation tool is feasible at certain sites. Included in this report is a remining program as part of the overall reclamation plan for two sites. Our preliminary results indicate that remining as a reclamation tool is feasible for only one of them.

Jan 1, 1981

By D. R. Flinn

A newly developed chemical conditioning technique, which greatly simplifies the preparation of plating baths for the electrodeposition of titanium diboride (TiB2) coatings, is described in this report. The new plating technique was used to prepare samples of titanium diboride (TiB2) coatings on three types of substrate materials. These samples were then evaluated in both low- and high-speed wear-test programs to determine the wear resistance, microhardness, and adhesion of the coatings. In general, it was found that the wear resistance of the coatings is independent of substrate. Scanning electron micrographs have shown that the coating wear surfaces are very smooth, suggesting slow and continuous removal of the coating during the wear test (that is, adhesive wear). Adhesion between the coating and all substrates was excellent. Microhardness results show that the TiB2 coating is harder than alumina, with a hardness value exceeding 5,000 kg/mm2 measured in one test. The results of the wear tests show that TiB2 coatings have relatively poor wear resistance compared with alumina in low-speed unlubricated sliding environments, but exhibit wear properties comparable with alumina in high-speed unlubricated sliding environments.

Jan 1, 1981

By Thomas J. Peters

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 17,320-acre portion of the 52,143-acre Little High Rock Canyon Wilderness Study Area (CA-020-913/NV-020-008) in order to evaluate its identified mineral resources. The study area is located in Humboldt and Washoe Counties, NV, about 42 miles north from Gerlach. Three areas of epithermal alteration, similar to alteration associated with disseminated gold deposits, were found in the study area. One of the areas occurs along a northeast-trending structural lineament. Southwest of the study area two gold prospects undergoing active exploration, as well JS a gold deposit being prepared for production, occur along the same lineament. The Bureau of Mines examination, however, did not find evidence for gold resources in the study area.

Jan 1, 1987

By L. Cheng

This report presents the results of a Bureau of Mines laboratory investigation of the effect of water sprays in reducing respirable dust that escaped the face area of a full-scale wooden model of a mine en-try containing a wooden model of a ripper-type continuous mining machine and exhaust brattice. Areas examined were (a) the general effectiveness of a low-pressure water spray system mounted on top of the mining machine boom, a high-pressure spray system mounted under the boom, and the combined top-and bottom-spray systems, and (b) the effect of these three spray systems on the capture of coal dust particles of different sizes. Dust was injected into a sump cavity at the face. Airborne respirable dust concentration was mea-sured behind the brattice with a personal sampler and cyclone, and particle size distribution was mea-sured with a cascade impactor. When used alone, the top-spray system captured about 55 pct of the respirable dust in the face area and the bottom-spray system captured 60 pct; the capture efficiency of each system is decreased when they are used simultaneously. From a mass-concentration viewpoint, each spray system preferentially captures larger dust particles.

Jan 1, 1988

This Bureau of Mines report is a reference manual of procedures used by the Bureau's Twin Cities Mining Research Center for obtaining rock properties. Included in the report are discussions on the usage of each property, descriptions of the general test methods for obtaining the properties, and instructions for performing the tests. The Instructions embrace details of the specimen configuration, test apparatus, test procedure, test conditions, and calculations needed to achieve satisfactory results. Although the procedures presented in this reference manual generally conform to recommendations of the ASTM Administrative Committee on Standards, they are not purported to be standards.

Jan 1, 1974

By Kenneth Eilerts

The development and operation of "combination wells"5/ have created new and unusual problems, many of which can he solved only if information is available concerning the properties of the fluids produced. Data as to the characteristics of the fluids at the relatively high pressures that exist in the reservoirs are especially important, and there is growing economic concern to know what part, if any, of the liquid recovered at the surface was liquid in the reservoir, As an extension of this problem, it is important to know, whether liquid will be formed in the reservoir as a result of isothermal retrograde condensation when the reservoir pressure is reduced. The pressure range of such condensation, if it occurs, is significant in the design of gas-recycling plants for maintaining reservoir pressures. In connection with the operation of such plants, it is particularly important to know how pressure and temperature will affect the yield of the liquid phase and the composition of the gas to be returned to the reservoir. It has not been possible to predict the behavior of these fluids that have high ratios off gas to liquid by comparing them with the behavior of low gas-liquid ratio fluids at identical pressures and temperatures. Such comparison fails because the proportions in which a component will be distributed between the phases of a system at any given temperature and pressure depend increasingly on the composition of the mixture as the critical temperature and. pressure of the system are approached. Because many combination wells are producing from reservoirs that have temperatures near the critical point, experimental date on the properties of the Fluids under reservoir conditions are particularly important at this time, To meet the immediate requirements of the industry for such experimental information, an equilibrium cell has been constructed at the Petroleum Experiment Station of the Bureau of Mines, Bartlesville, Okla. When adequate experimental date have been accumulated, it may be possible to make dependable estimates of the phase relations for high gas-liquid ratio fluids at the pressures anti temperatures characteristic of "combination-well? reservoirs.

Jan 1, 1940