Search Documents

By G. R. Hopkins

The average heat requirement per barrel of crude processed in the United states rose from 555,000 B. t. u. in 1939 to 579,000 B. t. u. in 1940, although crude runs increased from 1,237,840,000 barrels to 1,294,162,000 barrels in that period. Thus the almost invariable rule that the average amount of heat needed to refine a barrel of crude oil declines when total crude runs to stills increases was broken. (See fig. 1.) The reasons underlying the apparent loss in fuel efficiency in 1940 are quite obscure. There is little question but that the principle of heat exchange, the most important fuel saver, was used as extensively in 1940, as in 1939. A few companies replaced purchased power with electricity made at their plants, but for the country as a whole purchased electricity increased 7 percent, as compared with a 5-percent gain in crude run to stills. Furthermore, the premise the more complex the products the more fuel required -does not hold, as the yield of ?complex" products, including gasoline, declined in 1940.

Jan 1, 1942

By Robert W. Metcalf

Corundum, natural alumina, or aluminum oxide (A1203) is the hardest mineral known except diamond. Theoretical composition is Al 52.9 percent and 0 17.1 percent, but it always contains small quantities of impurities, chiefly silica, iron, and lime. The melting point of corundum is above 1950° C., and it is insoluble in the strongest acids. Its hardness (9 on the Mohs scale) varies slightly according to purity, and its specific Gravity ranges from 3.95 to 4.10, 4 being a fair average. The index of refraction is 1.760 to 1.768 and its streak is white. Luster is adamantine to Vitreous, come specimens pearly, and color varies widely from white, gray, pink, and blue to black, brown, or bronze. Gem varieties are transparent or translucent, and of more brilliant coloring - red, blue, yellow, purple, or green. Corundum occurs in opaque massive or block structure with parting planes little developed or only roughly delineated and in granular form as minute crystals or small, irregular grains interspersed throughout the contact zones of schists and gneisses.

Jan 1, 1944

By Howard W. Wainwright

The Bureau of Mines is engaged in a research program on the characterization of tars produced by low-temperature carbonization of coal and their economical upgrading to more valuable materials, Throughout the years, hydrogenation has played an important role in the treatment of these tars, mainly as a means of converting the whole crude tar or selected fractions to motor fuels; diesel oil, lubricating oil, or various solvents. In some instances, production of specialty chemicals has been the objective. The purpose of this report is to summarize, without critical review, the information of the past 25 years on the hydrogenation of low-temperature tars and related substances as presented in the literature or its English translation. Published articles and patents not abstracted in the main body of this report are included in a bibliography at the end. HYDROGENATION REACTIONS The hydrogenation of tar follows three general types of reactions; 1. The removal of oxygen, sulfur, and nitrogen in the tar to form water, hydrogen sulfide, and ammonia, respectively: [ ]

Jan 1, 1961

Background: Frictional ignitions continue to be a problem facing the U.S. underground coal mining industry. Many methane igni-tions are associated with the impact of mining machine cutter bits on quartzitic material (e.g., sandstone) during the coal-cutting process. Most ignitions result in small methane-air fireballs often only a few feet in size and limited to the cutter head location. However, under certain conditions, frictional ignitions can lead to larger methane explosions and/or fires with the potential for causing serious injury or death to the mining machine operator and other nearby miners. The requirements for a frictional ignition are a flammable volume of methane-air and an ignition source. This source is usually the hot streak caused by the frictional impact of the mining bit on hard rock, and the frequency of occurrence increases with increased bit wear. Another possible ignition source is the fric-tional impact of rock on rock during a roof fall.

Mar 1, 2008

By D. Bienstock

To develop a rugged catalyst capable of withstanding hydraulic attrition resulting from the oil-circulation process for synthesizing liquid fuels, use of an iron catalyst containing an active coating surrounding an inert solid core of metal was investigated. This massive-iron catalyst in the form of steel shot and lathe turnings was activated by partial oxidation with steam at 600° C, impregnated with alkali, and reduced with hydrogen at 450° 6. The massive-iron catalysts were resistant to oxidation and spalling, and a 6-month catalyst life was attained. Higher operating temperatures could be employed than with fused iron oxide catalysts, resulting in greater gasoline yields. Because the lathe turnings pack with void volumes of 70 to 90 percent, it has become possible to employ a fixed bed without the danger of cementation that occurs with fused iron oxides.

Jan 1, 1963

By Iain Finnie

This report is in three parts. The first part presents a review of theoretical models which have been developed to study removal operations for various types of materials. In the second part, a brief summary is given of coal cutting research. The majority of this work has been carried out in Britain using chisel type bits rather than the conical picks which are in general use in this country. However, a comparison of specific energies measured for conical picks in the laboratory and in the mine shows very encouraging correspondence. In the third part of the report, analytical models for coal cutting by picks are suggested. An extension of the British "tensile breakage" theory, developed for chisels, is given for picks. The role of crushing and cutting in coal removal is discussed as a theory which combines the two processes is shown to give reasonable predictions for specific energy requirements. Finally, directions in which the existing theory could be improved are presented and the need for further research is emphasized.

Jan 1, 1977

By W. I. Nissen

As part of its program to provide technology for reducing undesirable environmental impacts of mineral processing operations, the Bureau of Mines developed the citrate process for desulfurizing industrial stack gases that contain from 0.1 to 2 vol pet S02. In this regenerable flue gas desulfurization (FGD) process, S02 is absorbed from cleaned and cooled industrial flue gas with a citric acid-sodium citrate solution. The absorbed S02 is subsequently reacted with H2S to precipitate marketable elemental sulfur and regenerate the solution for recycle. Laboratory investigations of process parameters provided information for designing larger scale continuous operations. Information gathered from operation of two pilot plants, one at a copper smelter and one at a lead smelter, confirmed the laboratory results. Data were obtained for design and construction of a commercial-sized demonstration plant at the George F. Weaton Power Station, Monaca, PA. A preliminary operation of the plant was demonstrated, under a cost-sharing Bureau-industry contract. This bulletin describes the citrate process and gives results of the laboratory, pilot plant, and demonstration plant studies, as well as corrosion investigations.

Jan 1, 1985

By M. Didyk

In this report, the application of the PHU/MVS program is demonstrated through the use of a simple but realistic mine ventilation program. The report details, the problem description, the input data required and the various output features of the simulator. The PSU/MVS program is written in Fortran IV for use with IBM 370/168 computers. A version of the program that can be used in CDC computers is also available. A ventilation network consisting of 531 branches, 300 nodes and 5 fans took 48 seconds for solution on The Pennsylvania State University's IBM 370/168 computer. Appendix I of this report is the User?s Manual for the program. Appendices II and III contain the input data listing, and selected output listing for; the application. Appendix IV provides tables for leakage, friction factors and shape factors.

Jan 1, 1977

By J. R. Thoenen

This circular is part 5 of the third paper (entitled "Excavation") of a series summarizing the technical problems involved in the production and preparation of sand and gravel. Part 1 discussed the use of power shovels, draglines, and excavator cranes; part 2, power scrapers, slackline cable-way excavators, and hydraulic monitors; part 3, hydraulic, clamshell, ladder, and dipper dredges; and part 4, haulage systems in general, with particular reference to locomotive and car, hoist and car, and remote-control systems. This circular discusses the use of motor trucks, conveyor belts, pumps end pipe lines, barges and towboats, and aerial trams. MOTOR-TRUCK HAULAGE During recent years motor trucks have gained considerable ground as a successful competitor of locomotive haulage for quarries and gravel pits. Often where trucks have displaced locomotives and cars the operators readily admit an increase in both labor and total haulage operating costs but point to some other advantage as offsetting the extra expense. In other instances haulage costs have beep reduced by the use of trucks. In still others operators, having replaced locomotive haul with trucks, have again returned to the earlier method. Obviously gasoline-driven motor trucks cannot successfully compete with other types of haulage under all conditions. The apparent' growth in the number of advocates of truck haulage, however, indicates that it has passed the experimental stage and become a permanent competitor to other tyres.

Jan 1, 1936

By S. H. Ash

THE ANTHRACITE region of Pennsylvania contains over nine-tenths of the total anthracite deposits of North America and produces all but an insignificant proportion of the total output of anthracite in the Nation. The whole economy of the northeastern section of the United States depends, to a large extent, on the mining of Pennsylvania anthracite, which is shipped to New Jersey, New York, and New England and is a principal source of energy and heat for that entire region. The responsibility of the Federal Government for developing an engineering method that will prevent inundation of the Pennsylvania anthracite mines and keep them in operation has long been recognized. To obtain a reliable picture of the anthracite-mine-water problem and to solve that problem, it is necessary to have factual data on the volume and the quality and character of the mine water handled by the pumping plants in the anthracite region, as well as the kinds of pumps utilized and problems concerning their operation.

Jan 1, 1953

By R. L. Zick, J. D. Byars, T. P. Mucho

Recently, a large Pittsburgh seam longwall mine was nearing depletion of a major portion of its current reserves and had begun to develop in a different direction from its original portal area to access additional reserves. This meant that a large area of the mine would be abandoned and sealed. However, continued use of the original mine portal area required that the water accumulating in the abandoned mine would eventually need to be pumped to the surface. This would be in addition to the discharge water associated with the new portion of the mine. Several pumping and sump options were investigated to handle the quantity and quality of the anticipated discharge water. This paper describes some of these options, their advantages and disadvantages, and the final engineering decisions. Some problems and unanticipated outcomes, as well as the eventual solutions are discussed, including: (1) estimates of pump requirements, (2) water pool size, (3) eventual water quality, (4) anticipated inflows, and (5) integration into the overall mine water system.

By G. R. Hopkins

The average heat requirement per barrel of crude processed in the United states rose from 555,000 B. t. u. in 1939 to 579,000 B. t. u. in 1940, although crude runs increased from 1,237,840,000 barrels to 1,294,162,000 barrels in that period. Thus the almost invariable rule that the average amount of heat needed to refine a barrel of crude oil declines when total crude runs to stills increases was broken. (See fig. 1.) The reasons underlying the apparent loss in fuel efficiency in 1940 are quite obscure. There is little question but that the principle of heat exchange, the most important fuel saver, was used as extensively in 1940, as in 1939. A few companies replaced purchased power with electricity made at their plants, but for the country as a whole purchased electricity increased 7 percent, as compared with a 5-percent gain in crude runs to stills. Furthermore, the premise -the more complex the products the more fuel required -does not hold, as the yield of ?complex" products, including gasoline, declined in 1940.

Jan 1, 1942

By Richard G. Stearns

Extensive thick lignite apparently lies within 250 feet of the land surface in Dyer, Lake, Lauderdale, Obion and Tipton counties. Information on geology, land use, soils, groundwater and instability is compiled, along with a bibliography. A test and monitoring site was investigated at Fort Pillow Prison in Lauderdale County. Analyses were made of lignite, overburden, associated water and leachate. Lignite has high BTU (about 7800) and low sulfur (1.1% avg.). A year or more of data are presented on rainfall, water levels, and chemistry of surface water, groundwater, leachate and water from test pits. Main potential environmental problems are quality of surface water, and possibly shallow groundwater. The main aquifer of the region will likely be un-affected by mining. Low transmissibility of shallow aquifers will minimize lowering water levels of wells. Soil reclamation and conservation should be readily accomplished, Dangerous earthquakes have a low probability and mines are not significantly more hazardous than steep bluffs.

Jan 1, 1981

By William R. Barton

Sampling to determine development potential of beryllium deposits was conducted at 31 New England localities. A total of 54 additional areas where the geochemical environment appeared favorable were sampled to determine if economically interesting percentages of beryllia (BeO) might occur. Newry Hill-Plumbago Mountain, Maine, Iron Mountain, N.H., and Long Island, Maine, were investigated in some detail to determine the size and grade of deposits. The mineralized pegmatites at Newry Hill-Phunbago Mountain are extensive but very low grade; at Iron Mountain the ore bodies are very rich but of small volume; at Long Island beryl occurs with molybdenite, wolframite, and scheelite, but the tonnage of ore was not determined.

Jan 1, 1968

By A. G. Starliper

The Bureau of Mines made laboratory investigations to determine the feasibility of utilizing fine tungsten wires to reinforce a number of nonferrous metals and alloys and a superalloy, S-8l6. The composites of tungsten filament and metals were chosen to attain elevated temperature strength and corrosion resistance. Oriented clean or precoated tungsten wires were incorporated with the other metals by extrusion, swaging, and infiltration casting. Although widely varying characteristics were found in the composites, none were considered satisfactory for high-temperature use, chiefly because of reactions between the matrix metal-tungsten surface. Diffusion, solution, and chemical reactions between matrix and tungsten wires were sufficiently slow for some combinations, such as 15 v/o 8-816, to exhibit increased high-temperature strength for a limited time. A few metals failed to wet or bond to the tungsten surfaces, while a few responded after precoating with a third metal.

Jan 1, 1968

Approximately half of all the fuel energy used in the United States is now pro-vided by oil and natural gas. A persistent and rapid growth in energy demand during the last 3 decades has been absorbed largely by the liquid and gaseous rather than solid fuels. In 1948 the energy provided by coal was substantially the same as in 1920. Meanwhile, the use of oil and natural gas each had increased fivefold. On a per capita basis, the change is more significant. Coal consumption has dropped from about 6 tons per person to 4-1/2 tons, while oil has increased from 4-1/3 barrels to 14-1/3, and natural gas from 7,500 cubic feet to about 35,000. These facts would have only academic interest if the United States had unlimited supplies of all fuels. However, while the Nation's reserves of coal are adequate to meet our needs for centuries, those of oil and natural gas appear limited. It is obvious, therefore, that the security of our liquid-fuel position would be greatly enhanced if the supply could be based in an increasing degree on solid fuels, such as coal/and oil shale, which make up more than 95 percent of our fuel reserves, instead of natural oil and gas. In addition, this would create new employment and help to stabilize the market for coal, which may be facing comparatively bleak prospects in the near future unless its position with respect to other fuels is improved.

Jan 1, 1950

By E. D. Calvert

Molybdenum has been successfully cast into static and rotating molds in conventional equipment used for casting titanium and zirconium. Melting was accomplished by using an arc potential of 36 to 40 volts with a current of 10,000 amperes. Pouring efficiency, after a skull had been formed in the crucible, averaged 70 percent. Techniques are described by which four successful castings were made. Tensile properties on specimens cut from one centrifugally cast tube averaged: Tensile strength, 39,800 p.s.i.; yield strength (0.1 pct. offset), 35,300 p.s.i.; elongation, nil; reduction in area, nil; impact strength, 2 ft.-lb.; hardness DPH (diamond pyramid hardness) 180. Mold reaction was not evident in shapes cast in machined graphite. This was not true, however, for rammed graphitic-base molds.

Jan 1, 1960

By Sam G. Demou

Drag bit cutting tests were conducted chiefly to determine bit forces encountered in rock types representing a range of compressive strength and hardness and thus enable the design engineer to estimate a continuous miner's performance in a range of rock types. Testing was carried out on the Bureau of Mines uniquely designed, instrumented rock cutting device (RCD). This device can make 3-ft-long cuts at various depths and speeds to approximate full-scale drag bit cutting by continuous miners. Point attack and cutter bits were tested on four rock types ranging in compressive strength from 7,200 psi (trona) to 29,600 psi (Valders white rock). Cutting tests were made at depths up to 1 in and speeds up to 70 in/sec. Data included normal and cutting forces, groove depth, groove width, and weight of rock broken. The effect of varying the cutting speed was determined, and specific energies were calculated for the various conditions. The bit wear was also observed. For the rocks tested, compressive strength and hardness are good indicators of forces, specific energy, and wear encountered. Results, especially bit wear observations, show the possibility of extending continuous miners, already being used in trona, to Indiana limestone (10,000 psi). Rapid bit deterioration precludes use in Tennessee marble (16,800 psi) and Valders white rock (29,600 psi).

Jan 1, 1983

By J. A. Herbst

During the last decade it has been established that conventional flotation control strategies based on classical control theory result in significant increases in grade, recovery, and operating-cost savings. In the current report a description of an advanced model-based control philosophy is presented. The derivation and verification of a simplified flotation model is described. The implementation of a Kalman filter for estimation of unmeasured variables for input to controllers is discussed. Several control strategies using the model-based approach are described, emphasizing the nonlinear nature of the flotation plant. Expected trends in the implementation of such model-based flotation control strategies in the future are discussed.

Jan 1, 1986

By David C. Uhrin

Two improved methods have been developed to transfer microfilmed mine maps to suitable base maps showing surface features. The methods provide for (1) positioning and orienting maps; (2) merging adjacent maps; and (3) plotting maps at a common scale. One method produces an overlay mosaic of mine maps using an Integrated camera-processor. This photographic method shows the details of mine workings and is most useful for specific limited-area projects. In the second method, outlines of mine maps are digitized, manipulated, and plotted as overlays using a computer. This computer method can plot mine outlines and spatially index large numbers of microfilmed maps. Microfilmed mine maps used in this Bureau of Mines study are on file in the Mine Map Repository of the Eastern Field Operations Center. The base maps are U.S. Geological Survey 7.5-minute topographic maps. The demonstration area is located in the New Kensington East and West quadrangles, Pennsylvania.

Jan 1, 1977