Search Documents

By Robert L. Lagace

The objective of this task was to perform theoretical analyses related to identifying and increasing the understanding of wireless propagation mechanisms in mines, and for predicting the performance ranges and limitations of proposed systems. This was to be achieved by building on and extending previous ADL work* and utilizing experimental data as they became available in the radio frequency bands of interest. B. TASKS Theoretical radio wave propagation investigations undertaken on this task centered on three areas. The first area dealt with extending previous UHF wireless propagation results*: to estimate the losses caused by the presence of haulage vehicles such as trains in coal mine tunnels; to estimate the propagation losses and wireless communication ranges expected along a longwall coal face tunnel; and to assess the applicability of previous analytical approximations to tunnels having reduced crossectional dimensions, such as those found in low coal and in the presence of haulage vehicles. The second area dealt with the development of a suitable propagation model to adequately explain the unexpected, highly favorable LF to MF band wireless radio wave propagation behavior experimentally observed in Consolidation Coal Co.'s Ireland mine. The third area dealt with the formulation of a model for evaluating the overall system transfer function and transmitter requirements for a hoist shaft LF communications system, taking into account the hoist rope/shaft transmission line characteristics, the cage and sheave wheel line terminations, the signal inductive couplers, and hoist shaft signal and noise data.

Jan 1, 1975

By J. Drew Potts

In this U.S. Bureau of Mines study, four underground respirable dust surveys were conducted to determine factors affecting belt entry dust levels and how using belt air to ventilate work areas affected dust exposures. Belt entry dust levels on the surveyed longwall and continuous miner sections averaged 0.59 and 0.26 mg/m3, respectively. The stageloader-crusher contributed an additional 0.5 to 0.9 mg/m3 of dust to belt air, while the feeder-breaker contributed 0 to 0.2 mg/m3 of dust. A 1,000-ft increase in belt entry length or a 200-to 500-st-per-shift increase in production resulted in roughly a 0.1-mg/m3 increase in dust. Using the belt entry as an intake entry on the continuous miner section appeared to reduce dust levels by 0.1 to 0.3 mg/m3 during cutting. Belt air was not used to ventilate the face on the longwall section.

Jan 1, 2010

Mineral production was of little significance in the country's economy, and Bangladesh was not a world-ranked producer of any mineral commodity during 1977. Natural gas was the most important mineral exploited; however, reserves were sufficient to allow for much greater production, Economically, Bangladesh made some progress in 1977-782 in its struggle against poverty, underdevelopment, and rapidly increasing population. The gross domestic product (GDP) grew 8%, mainly owing to a 13% increase in food grain production, the key economic indicator in this highly agricultural nation. GDP at current prices dropped slightly in Fiscal Year (FY) 1976.77 to $6.6 billion3 and rose to $7.2 billion in FY 1977.78. The population rose from 81 million in FY 1975-76 to about 85 million in FY 1977-78, resulting in an increase of per capita GDP from $83 to $85 during the same period. The high annual population growth rate, over 3% in 1976 and about 2.8% in 1977, was recognized by the Government as the main problem facing the country. Average density was 525 people per square kilometer. A similar density would have the entire world population living within the continental United States.

Jan 1, 1981

By Pedro Lilienfeld

This report describes the development, design, fabrication and testing of a port-able, battery-operated, light scattering monitor (henceforth to be designated as ILSDM) for the rapid measurement of the concentration of respirable dust in mining environments. This instrument incorporates state-of-the-art design characteristics and makes use of advanced solid-state components both for light emission as well as for its detection. The use of a pulsed light source combined with synchronous signal detection minimizes drift problems and optimizes the sensitivity of the measurement. Simplicity of operation, reliability and ruggedness, light weight as well as improved performance were salient objectives of this instrument development program. Continuous clean-air flow screening of all critical optical surfaces, and optimized optical detection and electronic signal processing design resulted in about a hundred-fold decrease of noise and drift with respect to precursor instruments. Equivalent mass concentration measurements 88 low as 10 micrograms per cubic meter can be routinely performed with time constants of about 2 second.

Jan 1, 1979

By H. F. Yancey

The development, manufacture, and sale of small coal stokers suitable for domestic use has provided a new industry in the United States at a time when badly needed. Sales of domestic stokers have doubled each year for the past 4 rears, until in 1936 probably more than 90,000 such units were put into use. According to reports of the Bureau of the Census 79,543 residential stokers were sold in the first 10 months of 1937 by 109 manufacturers. This rapid expansion has made itself felt in the coal-mining industry. The smaller sizes of coal, either in a sized or slack condition, are in greater demand; as a result, preparation practices at the mines have had to be revised so that, in many instances, lump coal is being crushed to meet the demand for stoker coal. This situation in turn has necessarily resulted in a realignment of price schedules for the different sizes. One of the first underfeed stokers small enough for domestic use was developed at Seattle, Wash., in 1912; in 1916, a small overfeed stoker was developed at Seattle. These two types are generally considered to represent the beginning of the present domestic stoker industry in the United States. A careful inquiry as to the number of domestic stokers now installed in the Seattle area, made by C. R. Pate, who was detailed to this duty by the Works Progress Administration, indicated that probably 7,000 domestic stokers are being used in this area for residential heating. Most of these stokers axe of the overfeed type, although in the past 2 years the underfeed type has made rapid gains.

Jan 1, 1938

By N. Greninger

The Bureau of Mines conducted a laboratory study of the measurement of the water and rock dust (RD) contents of synthetic mine-type coal dust (CD) mixtures using a commercial unit for measuring water content and several prototype radiometric units for measuring the RD content. The RD content ranged from 50 to 100 wt pct and the added water (AW) ranged from 0 to 15 wt pct. The total water (TW) content (intrinsic (IW) and AW) of a small dust sample could be readily measured automatically by essentially untrained personnel using a commercial unit. The RD content of a sample containing only IW could readily be measured by moderately trained personnel using several radiometric units. With gamma-ray devices, about 300 g of sample is needed. With the improved beta-ray device, about 25 g of sample is needed. With dry mine dust samples, the estimated RD error range for gamma-ray devices is 0.8 to 2.3 pct and 0.5 to 1.0 pct for beta-ray devices. However, the radiometric measurement of RD content was questionable if the dust mixture also contained AW or if it was uncertain whether the dust mixture contained AW.

Jan 1, 1988

By W. W. Agey

The Bureau of Mines examined and tested the rhodonite deposits of the Silverton lead-zinc district, San Juan County, Colo., as a possible source of domestic manganese. Exploration and development work by several mining companies and preliminary reconnaissance of the area by Bureau of Mines engineers indicated the presence of extensive manganese resources in the form of rhodonite. This report summarizes the results of laboratory beneficiation tests made on samples of different type and grade material obtained from surface and underground exposures of seven veins in the district. Surface and underground examinations revealed the presence of several prominent veins that could be traced up to 2 miles for a single vein along the surface. The principal veins average about 50 feet in width and apparently carry rhodonite to considerable depth. Underground samples were taken from the Sunnyside, Silver Queen, Washington, Independence, and Scotia veins. Samples also were taken from surface exposures of the Sunnyside Extension and Hidden Treasure veins.

Jan 1, 1962

By A. M. Poston

Introduction of radioactive elements into ore samples and/or pregnant liquors and radiometric tracing thereof have greatly improved control of fusion and extraction studies on beryllium ores and products. Extractive metallurgical research on beryllium, normally guided by the usual laborious analytical methods, is both costly and slow. Recognition of this problem by the Bureau of Mines led to the development and application of radioisotope tracer techniques" as a substitute for chemical analysis at the Salt Lake City Metallurgy Research Center, The result was that much faster progress at significantly lower cost was achieved. This report discusses the problems encountered and resolved in using radioactive tracers and radiometric methods, defines the conditions and techniques for their effective use, and delineates the limitations and flexibility inherent in applying such methods in laboratory-scale beryllium research.

Jan 1, 1962

By Ned Baker

Details are given of a fuel-induction system for a hydrogen, fueled engine. The induction system was designed to preclude backfire otherwise common in hydrogen fueled engines. System features and test data are presented and discussed in the context of the requirements peculiar to use in an underground mine environment. The fuel induction-system when tested in conjunction with a modified Caterpillar 3304 engine provided backfire free engine operation and satisfactory engine performance.

Jan 1, 1982

By Reynold Q. Shotts

A study was made of the coal resources of an area in Jackson County, Ala., forming a part of the Flat Rock, Henegar, and Stevenson quadrangles. The area studied is a portion of the Plateau coalfield on Sand Mountain and is near the Tennessee Valley Authority's Widows Creek steamplant. Since no detailed geological study of this area had been published, some reconnaissance work was done. The coalbeds and adjacent strata such as sandstones, conglomeratic sandstones, and conglomerates were studied. Available drill logs, together with the areal geology, provided sufficient information to permit correlation of the coalbeds and an estimation of coal reserves. For all categories of reserves, computed on a regional basis, a total of 72,920,000 tons of coal more than 14 inches thick is estimated for the areas studied in Stevenson. Flat Rock, and Henegar quadrangles. Of this tonnage, 40,001.000 tons is estimated to have less than 60 feet of overburden. The total measured coal reserves for the above three quadrangles are 16,359,000 tons, with 12,471,000 tons under less than 60 feet of cover.

Jan 1, 1966

By E. A. Magill

This report is one of a series prepared by the Bureau of Mines on manganese deposits of the Northwestern States. It describes properties on the Olympic Peninsula, Wash. Exploration by the Federal Bureau of Mines in 1939-40 and 1954-55 on several typical deposits is summarized, and examination data are presented for other manganese deposits on the peninsula. An attempt was made to list all known occurrences; however, some properties are abandoned, and their exact location is unknown.

Jan 1, 1960

By GJ Hundman

The Multiple Unit Continuous Haulage (MUCH) System was designed to provide the capacity to continuously convey coal from the mining machine to the main haulage belt. The MUCH System has an operator who steers the lead vehicle, ever following the mining machine. All the remaining vehicles follow the path of the lead vehicle, with their conveyors automatically lining up between the lead vehicle and mine section panel belt. This is accomplished by mechanical linkages on the vehicles which are interconnected by steering bars between vehicles (patent pending). The MUCH System has an operator who steers the discharge vehicle when outby travel is required. Outby travel is just like inby, with each vehicle following the path of the preceding vehicle. Surface tests overwhelmingly indicate the "UCH System should track/retrack successfully in square pillar underground room and pillar coal mines with 18 ft. wide entries and slopes up to 10 percent. For 60 degree pillar plans the minimum entry width required is 15 ft. Surface tests also indicate the MUCH System will convey over 8 TPM of coal around 90 degree corners without excessive spillage.

Jan 1, 1983

By Lyman C. Hitchcock

The objective of this program was to determine the minimum luminance requirements for underground coal mining work from the working face to the first transfer point. The resulting data encompasses 114 visual tasks from conventional continuous and longwall mining methods representing the salient visual tasks found in the jobs listed. Cutter Operator Roof Bolter Face Drill Operator Airdox Operator Longwall Jackman Shuttle Car Operator Loader Operator Shot Fireman Continuous Miner Operator Longwall Head Conveyor Operator Longwall Tail Conveyor Operator

Jan 1, 1973

By M. Dattilo

The U.S. Bureau of Mines has been conducting research on the use of waste-derived zinc as a partial replacement for pure zinc in the electrogalvanizing process. The end product of this process is automotive sheet, which has enhanced cosmetic protection over previously used cold-rolled (CR) steel. In this study, primer-coated specimens of CR and electrogalvanized (EG) steel were subjected to the on-vehicle environment and monitored periodically by electrochemical impedance spectroscopy (EIS) during immersion in 1M NaCI solution. The results of these tests were compared with immersion-only conditions. Scanning electron microscope (SEM) and energy-dispersive X-ray (EDX) techniques were also used to evaluate the corrosion processes and compare them with atmospheric exposure specimens. EIS was found to measure the corrosion associated with on-vehicle exposure, thus providing an excellent screening technique for evaluation of the performance of EG automotive sheet steel.

Jan 1, 1990

By Henry Kreisinger, J. F. Barkley

This book is one of a series of publications being issued by the Bureau of Mines for the purpose of disseminating information in regard to the methods by which the fuels in this' country may be used most efficiently. A knowledge of the temperature of the gases in boiler settings and in other commercial apparatus using heat tends to develop improved designs of apparatus and better methods of operation, thus reducing waste of fuel. The following pages present, for the benefit of those designing, operating, and testing such apparatus, information as to the accuracy of temperature measurements made under certain conditions and the corrections that can be safely applied.

Jan 1, 1918

This study was done to evaluate the economic and technical considerations of using pozzolanic materials in order to guide cement manufacturers, pozzolan producers, contractors, Government organizations, and others interested in concrete construction work. Five hundred and thirty-eight samples of pozzolanic raw materials were taken from 27 central and western States. These samples were evaluated by petrographic procedures, and about 200 of the most promising ones were given a complete series of physical tests (American Society for Testing and Materials) to evaluate further their suitability as a pozzolan. This investigation showed that deposits of natural pozzolan materials were widely dispersed in the central and western parts of the United States but that exploiting these deposits would depend on whether they could compete economically with an increasingly abundant industrial waste product--fly ash.

Jan 1, 1969

By Donald W. Baggs

This report describes economic mining feasibility studies conducted by the Bureau of Mines to estimate mining costs in the Porcupine mining area of the Juneau Mining District, southeastern Alaska. Investigations were conducted on the economics of three mineral deposit types: 1) massive sulfide deposits containing zinc, copper, and silver, 2) vein gold, and 3)disseminated gold. Cost estimates were developed using the Bureau of mines Cost Estimating S,-stem. Discounted cash flow rates of return were calculated using the Bureau of Mines MINSIM (mining simulation) computer program. Three sets of metal prices were used in the study based on recent historical price information. Underground longhole stope mining of a massive sulfide deposit containing 25 pct zinc. 1 pct copper, and 63.6 g/mt silver was found to be economic at high metal prices at a quantity of 13,200,000 mt ore. Cut-and-fill mining of a 26,400,000 mt massive sulfide deposit was found to be economic at medium metal prices. Open pit mining of a similar deposit was found to he economic at medium metal prices and 26,400,000 mt ore, or at high metal prices and 6,600,000 mt ore. Underground mining of a vein gold deposit was found to be economic at a grade of 17.1 g/mt medium metal prices and 1,320,000 mt ore. Open pit mining of a disseminated gold deposit was found to be economic at a grade of 1.71 g/mt medium metal prices and a quantity of 39,600,000 mt ore.

Jan 1, 1986

By J. R. Thoenen

Profits in the crushed-stone industry, as in any other, represent the difference between selling price and production cost. When consumer demand increases rapidly, as occurred in the crushed-stone industry from 1918 to 1927, selling prices tend to rise. Cost of production usually rises, also, owing to the expense of expanding facilities, searching for and developing new quarries, and purchasing, installing, and operating new equipment. Frequently, also, the inattention of managements to the details of operating costs is responsible for their increase. This is not due to negligence but rather to the necessity of confining attention to the problems involved in producing material to supply orders. When market conditions change and consumer demand becomes stabilized or contracts, the producer's attention usually is directed to assuring the orders necessary to keep his enlarged facilities busy. Hence, competition increases and soiling prices decline.

Jan 1, 1939

To develop a conceptual design for an automated longwall mining system, one should know what has been done, what is being done today and what is being planned for tomorrow. The bibliography referenced and discussed in this report provides a good source for that knowledge. To scientifically determine where attention should be focused to up-grade a system, the system must be quantized as far as possible. The Mechanization Profile of Appendix A-I is discussed in this report and has been used to analyze and determine the degree of mechanization currently in use and/or described in the literature for all three major elements of the long-wall system, namely, Winning, Roof Support and Haulage. The charted profiles make it self-evident where attention and design effort is needed to remove human operators from the face of the mine.

Jan 1, 1975

By McHenry Mosier

The Bureau of Mines, United States Department of the Interior, has established a testing adit on the Government reservation at Mount Weather, Virginia, to facility to research on the fundamental tats of mining under actual metal-mining conditions. A number of sites in several Eastern States were investigated, out Mount Weather was selected because the rock seemed best suited for rock drilling and other mining tests and because the ground was already owned by the Federal Government, the site having been acquired in 1902 for use of the Weather Bureau. The testing edit has an advantage over en active metal mine for certain investigations because variable conditions affecting any particular research problem can be controlled and maintained in a fixed status, whereas in an operating mine this seldom is feasible. Operations were begin September 1935, with a crew of four laborers under a resident engineer. The laborers were recruited from, nearby farms, and. although they had no previous mining experience, they have developed into satisfactory miners.

Jan 1, 1939