Search Documents

By Atsuo Inoue, Toshihiro Ogata, Hideaki Sugihara

Generally in Japan, since ANFO has easy handling and low-price, it is most used as industrial explosives. However, ANFO is very easy to dissolve in water, it is difficult to use under existence of water and the consumer have desired water-resistant ANFO which has perfect water resistance. Then, we have developed the Water-Resistant Granular Explosive (It is written as following WRGE.) in which the surface of the explosive was covered by waterproof film, so that WRGE is able to use in hole with water. We ran various performance tests about the WRGE developed in the laboratory. Consequently, WRGE has water resistance of over 6 hours, and it has been checked that a performance and handleability were equivalent to the conventional ANFO. Then, we carried out the field test in the consumption site, and did performance evaluation on an on-site level. As compared with ANFO, fragmentation (size and volume) and handleability are almost equivalent. However, some problems which the WRGE is not settled out smoothly in hole with water and need more time for loading were also clarified. We are going to continue some advanced improvements through field tests.

Jan 1, 2005

By Julio Cesar Barbosa de Freitas, Rafael Gonçalves Araujo, Túlio Soares, Jair Koppe, Augusto Ferraz Ribeiro, Pedro Barreto Garcia

This study thesis was motivated by the fact that it is of fundamental importance for open pit mining that the slopes initially have a geometry in accordance with what is proposed in the mining planning. This occurs because an inconsistency in this design can impact the operational safety and economic solutions of the mining project. These consequences can be explained by the fact that rock blasting close to mining limits requires specific study due to the attention required. Because, when this operation is not carried out properly, the mining plan in the mine may not be respected and may create risks to the operation due to the presence of unstable blocks on the slopes (Mackenzie). In this sense, Mackenzie (2004) cites pre-split, trim blasting and buffer as commonly used explosive blasting techniques that aim to limit damage beyond the projected wall. Therefore, Enaex Brazil realized the need to better understand the pre-split method. To do this, it is necessary to understand how the energy released during detonation is perpetuated in the rock mass when this technique is used and when it is absent. Thus, this analysis is based on a seismic study that allows the creation of vibration attenuation laws and an elementary wave damage model, which allows the local characterization of the rock. With this model it is possible to relate the peak levels of vibration during blasting and the extent of damage, but a critical level of vibration (PPVc) and its relationship with the Uniaxial Comprehension Resistance (UCS) are also defined for the start of fracturing and its level (McKenzie et al, 1995). And, mainly, this work aims to address a way to measure the pre-split filter potential by comparing the attenuation law with and without pre-split, ultimately knowing whether this finishing blasting is being effective, to understand the pre-split filter capacity.

Jan 21, 2025

By C. Zuniga, S. Combrinck, C. Peters

Agnico Eagle Gold have partnered with Enaex Australia at their Fosterville gold mine to leverage a combination of drill and blast technologies to optimise underground development mining. The mine is the first site globally to collaboratively develop and trial Enaex SWIFT electronic development detonators, which utilise a novel approach to the user interface, simplifying implementation and enabling the benefits of electronic initiation without the complexity of a conventional system. This has been combined with the use of a Sandvik 422i smart jumbo, and the Enaex underground emulsion charging unit with the capability to tailor the delivery of explosives as required and report on a hole-by-hole basis. The combination of these technologies enables full engineering oversight of the development cycle, in turn enabling optimisation of this process in a historically conservative application. The methodology for leveraging these technologies is to bore a controlled and defined blast pattern through using a smart jumbo, load the blast holes utilising lace loading to deliver a desired quantity of ammonium nitrate emulsion per hole, with the ability to reduce chargeweight for perimeter control, and utilising Enaex SWIFT electronic detonators with flexible template type pre-defined delays to initiate the blast holes. Subsequent to firing and excavation the performance of the blast in fragmentation, advance efficiency, and overbreak and underbreak is measured and reviewed. This is then used to optimise the development cycle and apply to other parts of the mine.

Feb 6, 2023

By Gary Anderson, J. P. Remi Proulx

Rio Tinto’s Colowyo Coal Mine produces 2.1 million tons per year in northwest Colorado. Colowyo uses the terrace mining method to recover up to seven coal seams ranging in thickness from 5 to 20 feet. Coal recovery in the 6 foot thick high grade C-seam has recently been challenged due to large variations in the pitch and roll of the seam. As well, some coal damage was seen due to an increased thickness of the overburden consisting of a hard sandstone channel.

Jan 1, 2012

By Gloria Contreras

The study aims to optimize the density of holes per tunnel section. The energy distribution, the one with the highest density, is used in the center of the diagram and is distributed homogeneously towards the contours with the lowest energies up to the contours to produce a perimeter control.

Feb 1, 2020

By Eric C. Gerst

"In this current era of soft commodity and coal prices the mining industry is turning towards optimizingall levels of production to reduce operating costs. Part of this trend includes the automation of miningmachines. As the first tier of the mining process blast hole drill automation offers benefits through the entire value stream from drill bench to material processing."

Jan 1, 2017

By Scott Gustfason, Richard N. Snyder

What is a safe stand-off distance? Recent mishaps using conventional blasting equipment have seen flyrock as distant as 3,750 feet from the blast area, or close to three-quarters of a mile, therefore, whether below ground, under water, in surface quarries or at a structural demolition site, data signals riding a radio wave promise a new horizon for the users of both electric and non electric blasting circuits.

Jan 1, 1987

By Tamara Wiseman, David Stewart

"A Quarry located in Georgia is a green-field site established in 2011. The quarry lies in the eastern part of the Georgia Piedmont area. It is within a distinctive, northeast-trending belt of relatively high-rank metamorphic rocks known as the Kiokee Belt, a poorly mapped sequence of units that largely consists ofamphibolite and various schists and gneiss that are host for relatively young granite bodies andassociated pegmatite and aplite dikes."

Jan 1, 2017

By J Lyall Workman, Larry R. Fletcher

Blasting methods have been proposed for reclaiming abandoned underground coal mine sites having unstable conditions. The objective of blasting is twofold: the permanent stabilization of an area by the collapse of underground workings to prevent any future subsidence, and the use of blasting to close existing sinkholes.

Jan 1, 1991

By Charles E. Joachim

Railroad and blast induced vibrations were measured in the vicinity of the proposed Big Bend Cutoff. Peak horizontal and vertical particle velocity relations were developed using least squares regression analysis. The dominant frequencies of these data are in the range of 30 to 50 hz. Therefore, allowable charge weight per 30 msec delay curves were generated for buildings (2 in./sec) and unlined tunnels (8 in./sec). A blasting contour map is presented for this site.

Jan 1, 1984

By Tuan Nguyen, Dirk Hummel, Ruilin Yang

In a tunnelling site in Japan, it was found that detonators failed to initiate with their shells and primary explosive intact. Their capacitors, however, were discharged due to some damage on the application-specific integrated circuits (ASICs). These detonators are distinctly different from other commonly observed failures, where the shells are rather crashed due to excessive dynamic pressure received from neighbouring blastholes which fired earlier. Such incident has not been reported elsewhere. Detonator failures during a blast are deemed not safe and can cause disruption on the project productivity. It is therefore desirable to understand the origin of such event. Various measurements were conducted to diagnose the problem, but the root cause had yet to be identified. This paper applies a discovery from a 60-year-prior-laboratory experiment and formulates a theory that could explain the observed detonator failure and predicts the measurements and observations.

Feb 6, 2023

By Fred Baldassare, Marcia Harris, Kenneth K. Eltschlager

Surface mine blasting was recently investigated as a potential source of high concentrations of stray gases found in nearby residences of western Pennsylvania. In one incident carbon monoxide was detected in a home and in the other, high concentrations of carbon dioxide were found in a home. Both carbon monoxide and carbon dioxide are by-products of blasting. However, other potential sources of these gases may also exist in a residential setting. In each case, gas chromatography (GC) and carbon isotopic analyses were used to define atmospheric concentrations inside the homes, and to determine the source of a stray gas. Molecular and isotopic analyses provide geochemical evidence as to the origin and source of the stray gas. This paper discusses elements of a stray gas investigation and the analyses necessary to identify the source of a stray gas.

Jan 1, 2004

By Michael J. Sapko, Eric S. Weiss

The U.S. Bureau of Mines has been conducting research on the secondary explosion hazards associated with the mining of oil shale under gassy mine conditions. Explosive incendivity tests have been conducted in a 28 m~3 (1000 ft~3) gallery to evaluate the relative incendivity of experimental emulsion-ANFO blends. The incendivity was measured by determining the minimum inert stemming requirements for preventing the ignition of a methane-air atmosphere by the discharge of hot detonation products from a 5.7 cm (2.25 in) diameter borehole.

Jan 1, 1990

By Pavel A. Torres, Darwin Torres, Sandro Huaman

Given the limited efficiency of blast-induced ground vibrations prediction empirical models, due to the complex geological system from a Peruvian mine. An artificial neural network was built in order to get better results. More accurate and precise predictions allowed the generation of blasting domains for future designs and decision making.

Feb 1, 2020

By B. M. P. Pingua, M. Nabiullah

Number of mine accidents occurred in Indian surface mines are due to poor quality of explosives and blasting accessories. Amlori open cast project is one of the major coal producing projects in India. Standard drilling and blasting parameters are used to achieve desired productivity of the mine. 150 and 260 mm diameter blast holes are used for blasting in coal and overburden benches. Most of shovel benches are 12 to 16 m in height and dragline benches vary from 25 to 30 m. High-energy bulk emulsions are used for blasting. The cup density and velocity of detonation of bulk emulsion explosives are 1100 to 1200 kg/m3 and 3.8 to 4.5 km/s respectively. An incident occurred on fire bench of Amlori open cast mines during mucking of blasted muck.

Jan 1, 2008

By Nikolaos Petropoulos, Ulf Nyberg, Ulf Stenman, Daniel Johansson, Håkan Schunnesson

The optimization of the explosive performance is of great importance since blasting is extensively used in civil projects and mining industry. An improved understanding of how the energy from the detonation of an explosive is transmitted to the surrounding rock mass is critical information for the proper selection of an explosive. Therefore, an extensive study was done on the influence of the blasthole diameter on the Velocity of Detonation (VoD) and the detonation front curvature.

Feb 1, 2020

By D. Mason, W. J. Birch

Blasting operations are arguably one of the most contentious areas of surface mining.Many operators carry out outine monitoring as required by Mineral Planning Authorities. However in so doing they only concentrate on the observed Maximum Peak Particle Velocity (PPV) being below the statutory limit and pay little or no attention to the measurable parameters that determine this value (e.g. scaled distance, burden, detonator type, blast type or rock type). Such practice is “monitoring to comply”. What is needed is for the operators to adopt a methodology that clearly demonstrates to the appropriate regulators that the operator is “planning to comply”. The aim of the exercise being to deliver a process that is seen to be transparent, accountable, and quantifiable, which seeks to minimise environmental impact whilst not compromising the efficiency of the blasting operations mine.

Jan 1, 2011

By Ron J. Elliott, David G. Otto

This project involved deep blast densification of recent volcanic avalanche debris deposits consisting of a 43 meter thickness of loose clean to slightly silty sand, gravel, cobbles and boulders deposited as a result of the 1980 eruption of Mt. St. Helens, Washington, U.S.A. This project was carried out to enhance the resistance to liquefaction or dynamic settlement of soil deposits under the bridge abutments for construction of the 59.4 meter long South Coldwater Creek Bridge. As this bridge is located close to the Mt. St. Helens fault, it will in all likelihood be subject to earthquakes in the order of 6.5 with expected accelerations of 0.55g. Without soil densification, the bridge would suffer severe structural damage in the event of a significant earthquake.

Jan 1, 1994

By Minoru Kawamora, Koichi Kurokawa, Kenji Hashimoto

We developed concentrated remote control blasting system to blasting simultaneously at a large number of sites in a mine of large scale. This system is consisted of three parts, the first part is a control station with high voltage power source units, the second part is a relay terminal with relaying and branching units, and the third part is a blasting machine with charging and discharging units. The control station is connected with the blasting machine by mean of control bus wire. The blasting machine adopts MBS(electromagnetic induction blasting system) for the reason of safety and good handling.

Jan 1, 1990

By Lon Santis

This paper describes several applications of quantitative risk assessment in the management of commercial explosives operations. The Institute of Makers of Explosives’ (IME) quantitative risk assessment software modeling program IMESAFR was used for this analysis. Modeled activities include the unloading of a ship at port, locating a safe haven, and dealing with encroachment on a manufacturing facility. The layout of actual explosives sites were used for the analysis. The risk of fatality is analyzed and shown it can be used to make informed operational decisions for each activity. A study of the risks to individuals from activities involving commercial explosives compared to individual risks from other daily activities or exposures is also presented.

Jan 1, 2008