Search Documents

By J. H. Douglas, A. F. Matheson

"The Hard Rock is the most easterly producing mine in the Little Long Lac area. The Company was formed in 1934 to develop a surface showing of gold in quartz made by a prospector, W. W. Smith, in 1931. Although some ore was eventually produced from this discovery, the principal orebody, hidden below 10 feet of muskeg, was found about 1,000 feet to the north by exploratory diamond drilling early in 1938 from the No. 2 shaft workings at the 250-foot level.Production started in 1938 and to January 1, 1947, 201,000 oz. gold had been obtained from 1,165,282 tons of ore mined and 869,397 tons milled. Of this ore about 15 per cent came from the development and mining of the original orebodies discovered at the surface. The remainder came from the ore found by the underground diamond drilling done in 1938. Of the latter ore, the Company estimated, at January 1st, 1947, only 140,000 tons remained. The orebody, therefore, contained approximately 1,100,000 tons.OREBODIES AND GENERAL GEOLOGYThe orebodies of the Hard Rock mine are of two main types: the quartz ore of the south and No. 1 shaft zones, and the sulphide ore of the north zone. The quartz ore consists of white quartz veins mineralized with sparse, fine, light-coloured pyrite, or, less commonly, nests of coarse, crystalline, light pyrite. A little tourmaline, scheelite, pyrrhotite, chalcopyrite, arsenopyrite, and native gold are also present. Native gold occurs in a few places in quartz veins in exceedingly rich cemcentrations, apparently where there are large, light-coloured, pyrite crystals of imperfect form. The ore of the north zone is massive pyrite with arsenopyrite and in places pyrrhotite. Many short irregular quartz veins, from a few inches to 2 feet in width, are also present, but the quartz forms a very small percentage of the whole. The veins may be flat to vertical, and sulphides on one or both sides replace the host rocks. The gold is closely associated with the sulphides . The quartz is commonly barren except where it contains sulphides or along the borders of the sulphide ore zone where native gold is not uncommon in quartz stringers."

Jan 1, 1954

By S. Y. Mostowy, P. W. M. Shibley

"When Texas Gulf Sulphur Company discovered the Kidd Creek ore body in 1964, a crash program began almost immediately for the design and construction of a modern concentrator. It was necessary to mill two distinct ore types; one containing copper and zinc, the other lead, silver and zinc minerals. The final concentrator design was to handle 9,000 tons of ore daily in three circuits. One circuit was to treat copper-zinc and another lead-zinc ore exclusively on a permanent basis. A central circuit was designed with adequate flexibility to treat either of the above ore types in accordance with planned mining schedules. Ecstall Mining Limited, a wholly owned subsidiary, now operates the mine and concentrator complexes for Texas Gulf. The mine is located 15 miles north of Timmins and the concentrator 15 miles to the north-east along Highway 101. The ore is hauled from the mine to the concentrator over a 17-mile railroad. Initial milling operations began in November, 1966.1 - ABSTRACTThis paper deals with bulk reagent handling at the Kidd Creek concentrator. The reagent section at Kidd Creek has operated excellently since milling began in 1966. The bulk handling techniques are satisfactory. They have contributed substantially to good working conditions, economical practices and metallurgical efficiencies. The bulk handling features described should be considered in existing and proposed concentrators."

Jan 1, 1970

By E. Marcotte

"Technology developments and improvements are imperative to maintain a viable mineral processing industry. In order to achieve optimum implementation of technology in processing plants, safety conscious and efficient work forces are required. Effective management methods are required to prevent employee injuries, equipment or environmental damage and process losses. Good leadership also provides for employees to perform their work in the safest and most efficient manners to attain optimum recoveries of the valuable minerals and produce high quality mill products. Equipment and processes must be designed, operated and maintained as required to assure safe and efficient mineral processing.INTRODUCTIONThe Canadian mining industry must contend with many challenges to attain and maintain a competitive position in today's global market. Canadian Mineral Processors play a vital role in meeting the challenges and achieving optimum mineral productivity.Ongoing technology developments and improvements continue to be imperative to maintain a viable mineral processing industry. The efficient implementation of technology developments requires a safety conscious, skillful and productive work force.In addition to technical and human resources, challenges may also include governments, labour unions or environmental advocates who at times may appear to be misguided or unrealistic. Canadian Mineral Processors must not allow themselves to be overwhelmed by these apparent obstacles but must use their demonstrated ingenuity to achieve successful solutions.It should be recognized that the majority of the Canadian work force are, in fact, a potentially talented and skillful people with ambitions to excel. As leaders of people, we must provide the methodology, incentive and direction that will allow our work forces to realize their ambitions. If the potentials of our work forces are not recognized and leadership is not properly exercised much loss will occur. That is, safe effective and efficient work will not be achieved."

Jan 1, 1993

By R. K. Kandasami

"Naturally occurring geomaterials such as sandstone, limestone and other soft rocks, residual soils are composed of a particulates held together through a cohesive matrix, usually composed of argillaceous or siliceous cementing agents. Geo-materials such as these have been reconstituted in the laboratory using ordinary Portland cement in lieu of the naturally occurring cohesive matrix, in addition to using sand particulates. This cohesive frictional granular ensemble is an ideal model material for understanding the mechanical behaviour of transitional geomaterials such as soft rocks. An important consequence of this cohesion that pervades the inter particulate system is the enhanced tensile strength when compared to a purely granular ensemble. The assessment of strength of these soft rocks and cemented sands is often understood in the framework of continuum mechanics, i.e. considering the cemented sand to be a continuum, and performing simple elemental tests such as uniaxial compression or tension tests. A simple model to describe the behaviour of these cemented sands has been to use elements such as springs, sliders, and dashpots in parallel to describe the existence of a cohesive and frictional component of strength (Jiang et al. 2007). In the framework of continuum mechanics, the mechanical response of these cemented sands have been modeled using traditional plasticity theory, for example utilizing variants of the traditional Mohr Coulomb model, Modified cam clay (Sun and Matsuoka 1999) etc. The typical sand models are amended to include the effects of cohesion, as proposed by Lagoia and Nova (1995).The mechanical response of cemented sands is understood to be transitional to the behaviour of a typical particulate assemblage and a quasi-brittle material. However, the effect of length scale in these material systems has not been investigated. This paper presents a series of uniaxial compression experiments conducted on weakly cemented sand specimens of various sizes. The effect of length scale in these weakly cemented sands is investigated through unconfined compression tests."

Jan 1, 2015

By Diego L. Romero, Joy P. Romero

"IntroductionMinerals may be classed broadly as ferromagnetic (magnetite for example), as paramagnetic (attracts to regions of magnetic field convergence) and as diamagnetic (attracts to regions of magnetic field divergence). High-intensity separators are not necessary to separate ferromagnetic minerals from other classes. Rather, low-intensity units that generate fields below 5000 gauss are adequate for this purpose. However, paramagnetic minerals, such as ilmenite, with high magnetic ""attractability"" require fields of up to 10 000 gauss; those with low attractability may require even higher fields. Table 1 shows approximate ranges of field intensities necessary to separate ferromagnetic and paramagnetic minerals from minerals of lower attractability, along with the force with which they are attracted relative to iron in a standardized magnetic field.Uniform magnetic fields, not useful for separators, are generated between flat parallel surfaces; non-uniform fields, useful for separators, arise when at least one of the surfaces is of irregular shape. The diagrams below show how magnetic lines of force align relative to north and south poles.If a particle is placed in a uniform field, it feels no displacing force unless the particle distorts the applied field assymmetrically. This is not the case in non-uniform fields which are required for magnetic separators.Magnetic fields can be generated by permanent magnets (low intensity), by electromagnets (medium and high intensity) and even by superconducting coils (100 000 gauss fields and higher), although the latter are not as yet useful in production environments .The magnetic force of attraction per unit of mass, that acts on a paramagnetic mineral such as hematite, increases in proportion to the strength of the field . Unfortunately, the highest fields attainable with electromagnets is of the order of 20 000 gauss. Fortunately, the gradient of the fie ld (that is, the degree of convergence of magnetic lines of force) is important, because the attractive force per unit mass is proportional to it also . This can be stated:"

Jan 1, 1989

By K. Reinharter, J. Schmidl, D. Gregurek, A. Spanring

Copper smelting furnaces are typically lined with magnesia-chromite refractories, which are exposed to multiple and complex stresses. The selection of the processing route, furnace type and slag system will be dictated by the specific ore type available, this will determine the individual refractory wear. This paper evaluates the common refractory wear mechanisms as observed in the copper Peirce-Smith converter and in the copper anode furnace. The chemical factors include corrosion caused by fayalite type slag and sulfur supply, as well as, by Cu-oxide attack. Changes in the temperature during the furnace operation (thermal-shock) create stresses in the brick lining which can only be absorbed in limited extent. Mechanical factors include erosion, caused primarily by the movement of the metal bath, slag and charging material, as well as, stresses in the brickwork due to punching. Finally improper lining procedures can also effect the service life. All these wear parameters lead to severe degeneration of the brick microstructure and a decreased lining life. Therefore, a detailed investigation and understanding of the wear mechanisms through “post mortem studies” together with thermochemical calculations by FactSageTM software is an important prerequisite for the refractory producer. Based on these research results, combined with specific process knowledge, appropriate brick lining solutions for copper processing furnaces can be recommended. INTRODUCTION The refining of copper includes converting of matte or black copper into blister copper for final fire refining process in the anode section. Typically Peirce-Smith (PS) converters are in use. Other technologies include Hoboken Converter, TBRC but also Flash Converting Furnace and bath smelting furnaces (ISA, Ausmelt) (Davenport et al., 2002). For fire refining two types of furnaces are used – the rotary furnace type is dominantly used in the primary production route while secondary smelters tend to use hearth refining furnaces which are more suitable for scrap melting. Installed working linings are based on magnesia-chromite bricks but especially in the anode refining section the application of alumina-chromia bricks have become more popular in the recent years. It comes without saying that, to some extent, large variations in the slag composition can be observed from the data provided to RHI Magnesita during post-mortem studies of used refractory samples and this needs to be addressed properly during the selection process of refractory linings.77

Jan 1, 2019

By D. Seke, E. Katsande, R. Khumalo, K. Seerane

Palabora Mining Company (PMC) processes a multi-component ore body using a circuit consisting of two AG mills in parallel, closed with vibrating double deck screens and hydrocyclones. The bottom screen undersize feeds the hydrocyclones, but the screen oversize products can be treated in a variety of ways. The top deck screen pebbles can be crushed and then combined with the bottom deck oversize and recycled to the AG mill. Alternatively both the top and bottom deck screen oversize can by-pass the recycle crusher and be recycled directly to the mill. A full tap-off is a configuration when both the top and bottom deck screen oversize streams are stockpiled. The other configuration is when the bottom deck screen oversize is recycled to the mill while the top deck screen oversize is stockpiled - termed partial tap-off. This article reports the findings from the surveys performed to evaluate the performance of the PMC auto mill circuit when operated under the four different configurations discussed. Ore characterisation tests were performed to assess the deportment of the key ore components for the different configuration.

Jan 1, 2012

By K. van Netten, T. P. Ernst

"Froth flotation has been used successfully for about a century in the beneficiation of both coal and mineral particles. With the on-going trend towards lower feed grades, however, there is a need to transform this technology in ways that can deliver ultrafast separations, with strong selectivity, and recovery, covering a broader size range. It should be recognised that the hydrophobic effect, with its highly selective and long-range interactions, will most likely underpin any new technology. We identified the separation of the concentrate from the tailings as the rate determining step of conventional flotation technology. This limitation was then addressed by developing a novel flotation technology, insuring the formation of a concentrate that could be separated more rapidly from the tailings. We introduced a novel binder medium, a highly concentrated water in oil emulsion, to act as the focal point for hydrophobic adhesion, effectively replacing the air bubbles used in conventional flotation. The hydrophobic particles adhere to and become embedded within the binder, forming saturated agglomerates that float upwards. Moreover, by forming these large and resilient agglomerates, the product can be quickly dewatered over a screen and separated almost immediately from the tailings. Remarkably, this new binder permits residence times in the order of a few seconds under batch conditions. This paper examines the performance of the technology as a function of the oil wt% added to the slurry. The paper also examines the performance of the technology as a function of the particle size, showing a decline as the particle size exceeds 0.50 mm.INTRODUCTIONFroth flotation involves the collision and adhesion of hydrophobic particles to rising air bubbles, the carrying of those particles from the bubbly-pulp zone into a froth zone, and subsequent drainage and migration of the pulp to achieve the final concentrate (Wills, 2006). Within a Jameson Cell the feed slurry and air bubbles are brought into intense contact within the active area of the downcomer, achieving rapid kinetics of hydrophobic particle adhesion to the air bubbles (Harbort et al., 1994). However, once the bubble laden product and tailings emerge from the downcomer there is the need for separation of the concentrate from the tailings, an inherently slower process. In other devices such as mechanical cells the initial kinetics of particle adhesion are far slower, relying on the turbulent eddies throughout the cell, while in a column the kinetics rely upon an even slower process of bubble interception with suspended and settling particles (Gorain, 2007). However, in all cases the driving force for segregating the bubbles from the tailings, and the drainage of the froth are inherently the same. We do note, however, recent advances by Galvin and co-workers in achieving so-called Fast Flotation, utilizing a system of inclined channels to dramatically increase the segregation rate of bubbles from the tailings, permitting much higher gas and feed fluxes to be applied, achieving up to a ten-fold throughput advantage (Dickinson et al., 2014). Any further improvement within the existing flotation paradigm would require the introduction of centrifugal forces, but this would also require the formation of much finer bubbles than is typically used given the tendency of relatively large bubbles to reach a limiting slip velocity due to deformations and increased drag. Across all flotation devices we argue the rate determining step remains the segregation of the bubbles from the tailings."

Jan 1, 2016

By R. B. Humphrey

Cut-and-fill mining methods at the Thompson Mine have undergone significant changes since production began in 1961. Changes have been introduced in almost all aspects of the mining operation, from the original timbered chutes and air-operated slushers to the present-day bored raises, footwall ore passes and load-haul-dump units. This paper describes the evolution of mechanized cut-and fill mining methods, highlighting the changes in design for stopes and service openings, ground support methods; hydraulic filling and ventilation systems. A mechanized stoping area is described from the initial mining concept through design, development, construction and mining cycles.

Jan 1, 1979

By G. W. H. Norman

The surficial Archæan rocks of the southern gold belt of western Quebec are constricted near Kewagama lake by granite masses to the north and south. This divides the belt into natural eastern and western parts. This paper deals with the eastern part, extending from Malanie to Haig township. In this section the Keewatin-Timiskaming rocks have a length of about 70 miles and end abruptly against garnetiferous gneisses of the Grenville terrain. In the western half of the section where exploration has been under way since the early twenties, there are sixteen mines that are or have been in operation, and eleven prospective mines. In the eastern half where exploration has been carried on since the early thirties, six prospective gold mines are under development, one· of which, Louvicourt Goldfields, is at the initial production stage. Of the sixteen properties in the western half that are operating or have operated, all, except the Golden Manitou, which is a base metal mine, and the old Green Stabell from which there was a small production of copper, produce gold. Of the eleven prospective mines in the western half nine have gold. New Bidlamaque has gold and copper and one, East Sullivan, has copper-zinc ore. Since production began in 1927 gold, silver, zinc, copper, and lead having a total value of about $10,000,000 have been produced from the mines of the eastern section of the southern gold belt of western Quebec.

Jan 1, 1954

By G. Simard, D. Boudeville, A. Leclerc, A. Boivin

"The objective of this work is to study the various parameters that affect the overflow clarity of gravity settlers used in the precipitation circuit of alumina hydrate from the Bayer process. A mathematical model incorporating the size distribution of the feed suspension (Multi Size Group model), its diphasic nature (Schiller Naumann model) and the presence of turbulence (Shear Stress Transport model) has been solved numerically using ANSYS-CFX software. Preliminary results indicate that the overflow clarity is mainly controlled by lateral diffusion of fine particles (~20µm) from the exit of the feed well and by their upward transport from the sediment bed interface. Also the turbulence pattern in the settling zone seems to play a significant role in this vertical transportation. The validity of the model has been verified by comparing the measured solid concentrations from a pilot classifier with the calculated ones. This model could provide mineral processing plant operators and designers with a tool to optimize the configuration of classifiers with respect to the overflow clarity.INTRODUCTIONProblemIn the Bayer process, alumina hydrate precipitation from the saturated liquor is initiated in settler by adding crystallization seeds. Most of the precipitated alumina settles to the bottom of the tank while the liquor and the remaining alumina rise to the top, where they are removed at the overflow. Ideally the overflow clarity, which depends on the operational mode of the classifier, should be controlled within targeted limits."

Jan 1, 2016

By F. R. Archibald

MR. A. F. B. Norwood: Having been associated in the past few years with nine different plants roasting aurif erous concentrates in Australia, two of which were new installations for which design and construction were undertaken by the writer, I read Mr. Archibald's paper with very great interest, and I deem it a great privilege, as a member of a sister Institution, to be invited to contribute to the discussion on the paper. I wish to congratulate the author on a very informative and interesting paper, and, although situated many thousands of miles away, I feel I have gathered from it a very close idea of the operating conditions and of the work that has been carried on at the Beattie gold mine. Working along somewhat different lines, it is interesting to note that the conclusions drawn by the author run closely parallel to those accepted in Western Australia, viz., that the object of roasting is to obtain a porous calcine, and that this can best be achieved by roasting first at a temperature below 900 deg. F. to 1,000 deg. F., and then raising the temperature at the finish of the roast. Turning first to the laboratory work, the materials I have studied in Western Australia cover a range from those with little or no arsenic to concentrates carrying as high ?as 20 per cent, i.e., even higher than in the analysis quoted for the eoncentrates from Nepheline Products, Limited. In the ease of arsenic-free pyrite concentrates, the roast is ideally carried out at a temperature ranging from 900 deg. F. to 1,000 ferric oxide is one cause of the refractory gold remaining In deg. F. No improvement in extraction is obtained when the calcines are cyanided by raising the final temperature above this point; nevertheless, in technical practice it is desirable to finish the roast at 1,200 deg. F. in order to decompose basic ferric sulphate and thereby reduce the consumption of chemicals in the subsequent cyanidation step. However, if at any stage of the roast the temperature is raised above 1,200 deg. F., the extraction by cyanidation falls, and continues to do so the higher the maximum temperature that is reached. Line A in the accompanying graph typifies this effect.

Jan 1, 1949

By P. Radziszewski

Industrial practice in mineral processing shows that an important problem in understanding and monitoring in-mill parameters is due to the lack of fundamental knowledge and appropriate sensors. With the development and growing use of DEM charge motion simulators for mill optimisation and design, it is possible to describe the fundamentals of grinding mill behaviour, in improving the understanding of internal grinding mill dynamics and in developing solutions to industrial practice. The main challenge to bringing this DEM technology to the mill operator however was the need for substantial computing power and time. However, what about a simplified DEM charge motion model running in real-time? What about the use of sensor technologies to correct any possible drift in simulator prediction? Could such a technological system be used to predict mill performance and eventually be used for mill control and optimisation? Some of these questions are answered with the development of an "on-line" DEM charge motion simulator package (SAGTools?) along with that of a number of sensor technologies (liner wear, acoustic, instrumented ball) that can contribute to simulator precision. With the objective of bringing this modelling and sensor technology into the concentrator control room to assist operators, this paper aims to describe the main elements of this emerging and developing technology and discuss how it can lead to online mill performance prediction and eventual control.

Jan 1, 2007

By B. P. Verma, K. N. Sinha, N. M. Raju, B. Singh

The paper describes a new method of grouting bolts developed at the Central Mining Research Station at Dhanbad in India. This method makes use of wire-mesh sleeve instead of the expensive metal tube to insert the cement mortar into the drill hole. The field trials confirmed that the method is cheap and an effective system of support.

Jan 1, 1972

By Chris M. Healey

"Perhaps the single most significant variable in the evaluation of a mining project is the reserve estimate. Many parameters are considered when estimating reserves, among them geology. This paper examines the link between the quality of a reserve estimate and a good understanding of the geological controls for the deposit. A clear understanding of the geometry is essential to the accurate definition of the shape and size of the deposit. This includes the definition of any structural controls as well as the proper interpretation of the stratigraphy. Further when the distribution of grades is erratic and there is consequently a high nugget effect, there are significant problems in estimating the true grade of the deposit.Two Saskatchewan examples are presented, one with good knowledge of the controls and therefore good estimates of reserves, and the other with a poor understanding of the geology and resultant problems in deriving good estimates. In both cases the reserve estimates at various stages in the project development are compared to actual results from underground work. The first example is the Star Lake Mine where just about all the estimates were within 10070 of the actual on both tonnage and grade. The Laurel Lake deposit is discussed to show how problems in interpreting the geological data make reserve estimation very difficult. Laurel Lake has the additional problem of erratic grade distribution."

Jan 1, 1992

By K. M. Wild, C. D. Martin, F. Amann

Peak laboratory strength data obtained from low permeability clay shales/rocks often display a bilinear or non-linear failure envelope. In many of these tests pore pressures are not measured because of issues associated with back-saturation prior to confined compressive loading. In such tests the effective state of stress at failure remains unknown and provides room for speculation. The non-linear shape of the failure envelope may have several reasons including the influence of capillary forces or the tendency of a saturated clay shale to dilate as the confining stress is changed. The former stems from sample preservation, preparation or core unloading effects and represents a partly saturated state (i.e., not representative for the in-situ state); the latter represents the response of a saturated material. This contribution discusses these issues based on a data set obtained from Opalinus Clay specimens, and concludes that without a careful back-saturation processes knowledge of the underpinning reasons for the non-linear failure envelope cannot be obtained.

Jan 1, 2015

By J. H. . MORGAN

Talc-soapstone deposits exist in Patton Township of Quebec and have been mined by Bakertalc Inc. or its predecessors since 1938. The company produces products ranging from purified and micronized talc through to soapstone lumps. The deposits are found within serpentinite dykes and are zoned. Zoning grades from a serpentine core through zones of talcmagnesite, schistose talc and talc-chlorite schist be/ ore reaching the wall rock of quartz-sericite-chlorite schist. Talcmagnesite zones generally comprise 80 to 90% of the mined rock. The serpentinite dykes containing the talc probably were originally post-Ordovician peridotite of the same series that hosts the Eastern Townships asbestos deposits. Alteration of serpentine to talc-soapstone and magnesite apparently resulted through addition of silica and carbon dioxide along shears and fractures. Talc concentrations occur also at the intrusive contact between dykes and wall rock. The present Bakertalc Inc. operation at the Van Reel Mine is being worked from an inclined shaft 200 m below surface. The talc rock undergoes a variety of milling processes, depending on its particular market, be/ ore being bagged and shipped.

Jan 1, 1984

By G. V. Poropat

Roughness of a discontinuity may be an important factor influencing shear strength of the discontinuity. Traditionally, determining the roughness of a discontinuity surface and providing a numerical measure of the roughness has required considerable effort or specialised equipment. The development of new 3D imaging tools that are easy to use has provided effective fast and accurate means of creating 3D surface models from which roughness measurements can be readily obtained. These new techniques are versatile enabling a user to measure roughness along any desired profile and at any resolution up to the limit of the spatial subtense of a measurement on the discontinuity surface. This paper primarily reviews extensions to the use of 3D imaging that enable the measurement of roughness. Additionally we provide some examples of the measurements and examine some of the issues associated with extracting measures from the spatial data that will support estimation of shear strength.

May 1, 2009

By L. S. Trenholme

"Belleterre Quebec Mines, Limited, is a subsidiary of Mcintyre Porcupine Mines, Limited. The property is in Guillet township, Quebec, 45 miles due east of Haileybury, Ontario. It is accessible by 72 miles of gravelled road from New Liskeard, Ontario (Fig. 1).Gold production at the property commenced in 1936 and to March 31st, 1945, had exceeded $9,000,000. For the past 3 years the milling rate has averaged 325 tons a day and the gold recovery about $14 a ton.GENERAL GEOLOGYThe rocks of the district consist of Keewatin-like volcanics conformably overlain by Timiskaming-like sediments. Together they form the remnant of an easterly plunging anticline engulfed by granite (Fig. 2). The pregranite intrusives consist of diorite, gabbro, and ultrabasic rocks, occurring as dykes, sills, and irregular stocks. Dykes of porphyry and lamprophyre presumably related to the batholithic intrusive are common in this area. The veins of quartz are also probably derived from the batholithic intrusives. A few dykes of Keweenawan-type diabase have been observed."

Jan 1, 1954

By Alex MacEachern

Air is the gaseous substance that envelopes the earth and forms its atmosphere. It is remarkable in the constancy of its composition; for while this is being continually changed as the result of the respiration of men and animals, and by addition of gases arising from organic changes and the products of combustion, it is ever being brought back to normal and the proper balance restored by the processes of plant and vegetable life. Nature sees to it that the air in which we live and breathe is kept purified. This does not apply to the air in a coal mine, where there are no natural forces to change and make use of the different gases formed or evolved, and where mechanical ventilation is the only effective means of keeping the air pure. The atmosphere consists of oxygen and nitrogen, not in the combined state but merely mixed. By volume, the composition is: oxygen, 21 percent, nitrogen, 79 percent, there being included with the latter small quantities of such substances as water vapour, carbon dioxide, nitric acid, ammonia, ozone, argon, neon, and organic gases. Of the two principal gases which form air, oxygen alone supports life. When air is inhaled into the lungs the oxygen is absorbed by the blood, which carries it through the body to nourish and energize it. Exhaled air consists of water vapour and about 4 per cent carbon dioxide, with from 16 1/2 to 17 per cent oxygen and 79 per cent nitrogen; the oxygen alone having been drawn on to any considerable extent.

Jan 1, 1930