Search Documents

By Ling Wu

The development of pyrometallurgical technologies has been focused on new smelting reactors, but the proposal for new converting reactors has been substantially lower. Up to today about 80% of copper matte is treated by the traditional P-S converters which have the weakness of pollutant fugitive emissions. Therefore, the continuously converting processes for treating molten matte have been studied and developed. In July 2017 the "oxygen-rich side blowing smelting + multi-lances top converting & fire refining" continuous copper treating process was commissioned. This process was designed by ENFI and YanTai GuoRun Copper Smelter. In this process, oxygen rich side blow technology is adopted for smelting, which is a new type of side blowing smelting furnace to produce high-grade copper matte. The converting adopts the horizontal multi-lances top-blowing continuously converting process, which eliminates the transportation of molten melt and the SO2 fugitive emission. The intermediate products of this process, copper matte and blister copper is fed into the furnaces respectively through launders. This new process is more advanced, more reliable and more environmentally friendly. Until now, this process in the GuoRun copper smelter is operating smoothly. An increasing number of projects which use this process are under design and construction in China. INTRODUCTION At present, there are many advanced smelting technologies for copper concentrate, such as oxygen bottom blowing smelting, flash smelting, top lance smelting (including ISA and Ausmelt furnaces smelting), side blowing smelting, Mitsubishi smelting, etc. At the same time, there are many copper matte converting technologies such as oxygen bottom blowing continuous converting, flash converting, Ausmelt top lance converting, horizontal multi-lances top blowing converting, Mitsubishi converting, P-S converter converting, etc. The final blister copper fire refining technology mostly adopts rotary anode furnace. Therefore, in the process of processing and extracting the copper from concentrate to produce anodes, there are dozens of technology combinations. Among them, the non-continuous converting technologies for molten or cold matte are often adopted in the converting process. The traditional P-S converting technology had been utilized for over one hundred years, with a mature, reliable and simple operation, also has advantages in the secondary scrap smelting of a wide range of quality. However, due to its batch operation, frequent roll in and out, poor sealing, considerable air infiltration, needs for ladles for molten phases transportation and other characteristics, the technology has a serious pollution problem due to fugitive SO2. At the same time, in the cold matte converting technology, the molten matte needs to be cooled and then processed. The sensible heat of the molten matte cannot be recovered, and the preparation process is needed in the process. Therefore, both energy consumption and investment are relatively higher.

Jan 1, 2019

By J. A. Haskin

The Engineering Department at Flin Flon has the following responsibilities: 1. Underground Surveying. 2. Open-Pit Surveying and Supervision of Blasting. 3. Mine Geology and Examination of Prospects. 4. Design of Plant Additions and Improvements. 5. Miscellaneous Field W ork, Reports, etc. The entire surface plant, as well as the underground workings, are located by co-ordinates based on a triangulation system covering an area approximately one mile long by one-half mile wide. The origin of this system and one end of the base-line is the southwest corner of Township 67, Range 29, west of the Principal Meridian. The bearing of the base-line was determined from the township boundary, which runs true north, so that all other bearings are almost astronomical. This is a great convenience when our surveys must be tied to mineral claims, rights-of-way, and land subdivisions. As the base-line extends across Flin Flon lake, its measurement across smooth ice was simple and accurate. The length, slightly over 1,600 feet, has been adjusted for the temperature and tension of the standard tapes used and checked sufficiently to ensure a maximum error of 1 : 15,000. Each angle was repeated ten times, but as no special refinements were used, errors of as much as four or five seconds are possible. The elevation of the origin of the triangulation system was approximately 1,050 feet above sea level. The use of this true elevation in our surveys would have resulted in negative elevations underground as soon as the mine reached a depth greater than 1,050 feet. To avoid this complication we therefore added 4,000 feet to this elevation. The collar of the Main shaft, for example, which is actually 1,072 feet above sea level, appears in our records as at elevation 5,072. Underground surveying, which follows standard practice, is done by two mine surveyors who share three helpers. The meridian is taken underground from two wires hung in either of the two vertical shafts.

Jan 1, 1935

By M. J. Steffens

ESPLIM is a novel separation technique that combines the advantages of solvent extraction and electrostatic dispersion but its application in the extraction of nickel by the direct solvent extraction route and the effect of high electrostatic field on the stability of organics have not been explored. These were investigated in this study and it was found that the technique allows 97% extraction of the nickel in a single stage compared with 3 stages by the conventional solvent extraction. Also, three months of exposure to 5.0 kV under simulated operational conditions had no adverse effect on the stability of organics.

Jan 1, 2005

By E. Y. Carlson

"IN A SHORT PAPER it is impossible to do much more than to list the industrial minerals found in Saskatchewan and to give a brief description of the activity associated with each. I will not attempt to discuss the geology. It is sufficient to say that the settled part of the Province is covered by glacial drift which varies in thickness from a few feet to several hundreds of feet, and that this has hindered the search over much of the Province.CLAYA notable exception to this is the Cypress Hills area in the southwest corner which did not suffer any glacial action and where we find some of the large exposures of Cretaceous clays. In this area, the majority of the deposits are of stone-ware clays which are •an excellent raw material for such products as face brick and sewer pipe. Although the clay cannot be transported over any great distance it is used extensively in Alberta and Saskatchewan in the production of these products."

Jan 1, 1959

By J. A. H. Church

MR. J. A. H. CHURCH: The salient feature would seem to be that the thickness of the seam, in our coals at any rate, is the main factor in predisposition to spontaneous ignition. The evidence, incomplete it must be admitted, in the Saskatchewan and British Columbia fields, and complete in the Alberta field to my mind, shows this up very strongly. The German report on the upper Silesian coal fields definitely fixes the critical thickness at 13 feet, the British report goes far beyond this figure by stating that liability to ignition increases with the thickness of the seam over four feet. Before discussing the Alberta fires it would be well to note an error on page 12 -the probable cause of the fire in the Frank Mine should read "Spontaneous near fault. Heating first discovered 1909". Of the six fires attributed to spontaneous ignition all the seams were identical or in excess of the critical thickness mentioned in the German report. If there be any reason in the foregoing it is high time some forethought were taken to adopt some definite system of laying out the workings of such seams not so much on the outcrop districts as with a view to the future operation to the dip. Seams approaching 13 feet in thickness which to date have shown no disposition towards heating during the extraction of the outcrop areas may well cause infinite trouble or indeed total loss when the ventilating pressures increase as increase they must to the dip. This state of affairs can be combatted only by the adoption of a correct system of working and the provision of numerous airways of as large an area as may be compatible with the physical characteristics of the particular seam.

Jan 1, 1923

By Anthony P. Makuch

Dynatec Corporation is an integrated mining services company, providing mine development, operations management, engineering, drilling and metallurgical services to the North American mining industry. Dynatec was the contract operator of the Ken Snyder Mine in Midas, Nevada from start of production in January 1999 to September 2001. This paper summarizes Dynatec?s experience and approach to the use of longhole stoping methods for mining to widths of 1.3 to 2 metres in a steeply dipping narrow vein orebody.

Oct 1, 2001

By G. J. Reid, D. H. Stewart

"A diversity of structures and rock types in the Aft on pit has resulted in the occurrence of several different types of wall failure. Delivery of ore to the mill has not been affected and safety has not been compromised thanks to effective remedial 1V0rk and to a system of structural mapping, back analyses of failures, groundwater monitoring, and simple movement monitoring. Remedial measures have included artificial support, dewatering (including vacuum-assisted drainage), flattening of slopes and temporary buttressing. This paper describes six different wall failures at Afton and highlights the features of each. Examples given include rates of movement, extent and direction of movement, and piezometric responses. The practical, low-cost monitoring system was sufficient in one case to allow the prediction of date of failure. IntroductionThe Afton copper deposit is located 13 km west of Karnloops, British Columbia and has been mined for nine years out o f an expected eleven-year life. Open pit mining has reached 700 feet below sur face and is designed to proceed to 970 feet below surface by the time the pit is completed. The excavation is in a structurally and lithologically complex environment. Inevitably, some wall failures have occurred but these have been limited to small, manageable failures which have not compromised production or safety. To handle the failures it has been necessary to understand their nature. Of prim e concern has been the rate s of movement, but displacement vectors and hydrology have been monitored as well. The monitoring system is based on EDM surveys and on wire extensometers and plates set across cracks. Water levels have been read in standpipe piezometers. At Afton the emphasis has been on simple, practical, and inexpensive monitoring and because rock type s and structures play such a major role in any failure, detailed geologic al mapping is carried out."

Jan 1, 1988

By T. A. Wheat

"The presently increasing world-wide interest in advanced ceramic materials is generally focussed on their exploitation in both structural and functional applications. With the opportunity to engineer microstructures and thereby closely control and tailor the final properties, there are many new applications being made for these materials in both areas.The scope and some of the applications for functional ceramics are reviewed and examples of the present Canadian activity in this field are discussed.BackgroundThere has been progressively increasing international interest in the development and exploitation of ceramic materials in the last five years. The stimulus for this interest arises from several quarters, each of which are independent of the other.• There is a growing awareness of the strategic nature and vulnerability of supply of the raw materials used to produce high performance metal alloys.• The metal alloys are reaching the upper temperature limit for their performance as structural components in engines.• The dramatic increase in oil prices during the late 1970s focussed attention on the need for reduced consumption in many sectors, i.e., there is a need for more efficient engines that operate at higher temperatures - above those tolerated by the present superalloys.• A number of ceramics, especially the structural materials such as SiC, A120 3, AI20rSi02, Si3N4 and the Sialons are produced using non-strategic raw materials and they can exhibit startling performance-auto turbo-rotors are in production mad e of Si3N4 that operate up to 190000 rpm at 600°C, 150000 rpm at 900°C.• Ceramic s are generally of lower density - significant in the weight-reduction of automobiles such as the replacement of a 20-kg five-segment steel leaf spring with a single segment carbon-fibre reinforced unit of 3 kg. • Ceramics also offer major ad vantages in generating, monitoring or controlling the electromagnetic spectrum whether in bulk or thin-film devices that exploit optical, magnetic, pyroelectric, piezoelectric, electronic and I or ionic conductivity characteristics.The opportunity to combine several of these char acteristics in a single material by composition, processing and microstructural design has resulted in an advanced ceramics industry that had world-wide sales in 1980of $4.2 billion (U.S.)(I) and is predicted to grow to sales in the range $7 to $10 billion by 1990 and $16 to $24 billion by the year 2000(2). However, at present, advanced ceramics account for less than 20010 of the total ceramic market."

Jan 1, 1987

By X. J. Luo, F. Zhang

"Metallurgical slag (MS) such as steel slag, copper slag is a renewable resource and its compressive strength exceeds 200MPa in general. Because pure metal slug can easily be mixed into MS, complex recycle system is necessary in order to realize MS’s recycling. Meanwhile, there is high equipment failure rate in conventional crushing system. New crushing systems with inertial cone crusher could solve this problem very well. Recovery rate of MS tailings requires that crushing product can’t contain too much oversize product, so the essential equipment include two crushers and one sieve in the traditional crushing system. The new crushing system which only includes two crushers can meet the requirement and simplify the crush process. Investment of crushing equipment and infrastructure can be cut down. Operating and maintenance costs can be obviously reduced due to the simple process, which also could achieve high energy saving and excellent economic efficiency.INTRODUCTIONMetallurgical Slag (MS) such as steel slag, copper slag is a typical industrial solid waste and it threatens our environment’s safe. Metallurgical enterprises must take action to settle these wastes in order to protect our environment. Because pure metal slug can easily be mixed into MS, its uniaxial compressive strength (UCS) will exceed 200Mpa. If crushing station employs traditional crushing equipment, equipment failure will be easily caused because of these pure metal slugs. Coarse crushing equipment usually adapts jaw crusher in traditional Crushing technology and rod mill will be utilized to finish the secondary and fine crushing works. And the same time screening machinery should be used to ensure the suitable particle size (Figure 1)."

Jan 1, 2016

By Greg Yuriy

This paper discusses research carried out by the Laurentian University Mining Automation Laboratory (LUMAL) in the field of discrete-event simulation of mine equipment systems and reliability assessment of these machinery using genetic algorithms. The AutoMod simulation package, from Brooks-PRI Automation Inc., is used in this research. It is a 3-D discrete-event simulation/animation software tool for creating realistic depictions of manufacturing and materials handling systems. Discrete-event simulation involves modeling of real-life systems based on variables and events which occur or change at distinct points in time. In our case, a two level, multi-drift sublevel stoping model was created in AutoMod for the simulation of the equipment fleet employed in the development cycle (drilling, explosives loading, blasting, materials hauling, ground support) of a typical underground mine in the nickel mining region of Sudbury in Ontario, Canada. The equipment primarily considered in the simulation is Load-Haul-Dump (LHD) vehicles (scooptrams), drills, explosives-loaders and roof bolters. The purpose of the simulation study is to assess the impact of equipment failures to mine?s production throughput. In more detail, using Mean Time Between Failures (MTBF) data of scooptrams derived from a reliability assessment model based on genetic algorithms, LHD failures are incorporated into the simulation model. These failures cause production interruptions to the development cycle and consequently loss of hauling capacity. This paper will indicate the significance of equipment failures to a mine?s production and suggest a methodology based on the combination of discrete-event simulation and a predictive reliability assessment model using genetic algorithms for the study and analysis of mine equipment systems.

May 1, 2003

By Collin Bartlett, H. Storch

"Modern metallurgical processes operating with oxygen enriched air, such as the Outotec Flash Smelter and Flash Converter, generate very concentrated SO2 off-gas, which in combination with Outotec sulphuric acid plant technology allows the production of high pressure steam to be used for power generation. Outotec combines well proven technology of sulphur burning plants for this purpose with metallurgical plants.The application of Outotec’s proven LURECTM process enables processing of SO2 gas of up to 25 vol.-%. This process maximizes the energy recovery from the SO2 oxidation at a suitable high temperature level which can be turned into high pressure steam. The application of the Outotec HEROSTM heat recovery system enables the generation of low pressure steam from the absorption energy released at the intermediate absorption step. Additionally, energy is also recovered in the acid coolers for boiler feedwater pre-heating.The concept of integration of high and low pressure steam in combination with the pressurized operation of the boiler feedwater deaerator, thus heating up the boiler feed water to temperatures around 160…170°C, enables indirect transfer of low pressure steam (for deaerator operation) into more valuable high pressure steam, which improves the degree of heat recovery. This is the characteristic of Outotec’s HEROS+TM process.The increased generation of high pressure steam will in turn enable the generation of more electricity when compared to a standard traditional sulphuric acid process."

Jan 1, 2014

By W. E. Selnes

Introduction In 1938, a survey conducted by the Ontario Mining Association revealed a rather startling fact. Injuries incurred in chute pulling were more numerous than those from any other single cause. This report prompted Mr. W. B. Paton, then Inspector of Mines for Manitoba, to make a similar survey of the mines of his Province. It indicated that, in Manitoba mines, chute accidents ranked second only to those from falls off roofs and sides. Why has the mining industry been so slow to recognize the dangers of chute pulling? A partial answer may be the lack of any systematic classification of accidents according to their real cause. The result has been to attribute to other causes injuries which were a direct outcome of chute pulling, and, indeed, has made it difficult to analyze accidents in the industry as a whole. Perhaps, too, because chutes are generally located in the comparative safety? of the drifts, there has been a tendency to consider the occupation as not very hazardous. Not until enough statistics were obtained on this particular task could it be appraised correctly. The Mining Association's survey has been most helpful, and latterly the industry has done a great deal toward analyzing the causes of chute accidents and toward determining an effective means of overcoming them. Much, however, remains to be done. An effort will be made in this paper to outline methods which have been found successful in materially reducing the number of injuries. Qualifications of the Chute Puller First of all it must be realized that chute-pulling is a specialized occupation. The men require proper training for the job, just as in other mining operations. Care must, therefore, be taken to choose persons whose qualifications fit them for the job. Chute-pulling is an integral part of the general mining operation and cannot be considered as isolated from the tasks of other workers. One of the essential qualifications of a chute-puller is a sufficient knowledge of mining operations to appreciate the effect his work will have on the safety of others in the vicinity. He must take the necessary precautions, by verbal warnings, by placing barricades and signs, or by personally guarding the chutes, to prevent accidents to fellow workers.

Jan 1, 1947

By J. Paquin, P. Doiron, G. Proulx, P. Champoux

After nine years on a 36 hour schedule and two programs of creeping, the Alcoa Deschambault Potroom of faced the necessity of changing its organization for many reasons: the anodes butts were too small, the anode schedule was unbalanced, the iron content in the metal trends had increased, the metal tapping volume did not convene with crucible capacity and the liquid measurement task was delayed by tapping activities. A kaizen activity inspired the Potroom department to improve the organization. A team of 15 people including the process engineer, the process technician, team supervisors and Potroom operators developed a scenario, which would permit flexibility to creep pots if energy is available and an increase of added value production.This paper will describe the systematic approach, the communication method, the trials, the changes, and our success, along with the problems experienced by the team during the adaptation of Alcoa Deschambault Potroom organization over a 20 month period. Aluminium 2006 45th Annual Conference of Metallurgists ofCIM Montreal, Quebec, Canada Edited by

Jan 1, 2006

By Desmond M. Connor

"The State of the EnvironmentRecent data from a State of the Environment report prepared in January 1991 and released in April (see references) , indicates that the physical and biological environment across Canada is deteriorating in some important ways. For example: • emissions and atmospheric levels of CO2 are rising at a rate more than 50% of the U.S. increase; global temperature continues to rise, especially during the last decade;• while S02 emissions have been falling since 1984, NOz has declined only slightly since that time; N02 in Canada rose 43% during 1970-87, compared with a 7% rise in the U.S.;• municipal discharges of phosphorus and BOD (biochemical oxygen demand) to fresh water have been rising steadily since 1983);• pulp and paper mill discharges to fresh and Pacific coastal waters have been rising, 1970-87;• migratory game bird populations (Prairie Mallard, Northern Pintail) have been declining for the last 20 years;• total per capita energy use continues to climb.The State of the PublicSimilarly, data from recent public opinion surveys shows that public concerns about the environment are either rising, or are remaining at a high level despite the competing claims of the economy and political events for attention.For example, Professor Reginald Bibby's national survey this year shows that Canadians rank our top three issues as theeconomy, the environment and government incompetence.An Angus Reid survey commissioned by the Mining Association of Canada and other mining organizations in 1989 showsthat, despite general support for its economic benefits:• 67% of the general public perceive the mining industry to be a major source of pollution and environmental contamination;• 68% believe that a new mine should not be developed if it will disturb local wildlife;• 52% would prohibit a new mine if it required a road through a national park;• 49% would disallow mine development if it took as much land as an average farm in an agricultural area or if it limited sports fishing in a local lake."

Jan 1, 1991

By Paul W. Richardson

"Introduction And AcknowledgmentsTHIS PAPER outlines the geology and discusses the geological problems of the Mindamar mine. It is impossible to acknowledge the contributions of ideas of all the geologists who have worked in the area. Among the more important contributors are K. DeP. Watson, W. S. James, B.S.W. Buffam, and L. J. Weeks, and John MacPherson, the resident geologist at the mine.A mineralogical and chemical study of the ore and country rock is being carried •on by Dr. Watson at the University of California, Los Angeles.General InformationThe Mindamar mine is on Cape Breton Island, forty miles south-west of Sydney (Figure 1). The nearest railway stations are at St. Peters, which is thirty-two miles southwest of the mine, and at Sydney. Good gravel-surfaced roads connect the mine to the railways.The mine is producing at the rate of 600 tons a day of ore containing zinc, lead, copper, and minor amounts of silver and gold. At the present time the mill feed averages 9 .per cent combined metals, of which zinc makes u:p 7 1per cent and lead and copper each 1 per cent.General GeologyThe ore being mined ,by Mindamar occurs in a shear zone parallel to a northeasterly striking, vertically dipping, series of rocks consisting of rhyolite tuff, rhyolite, minor more basic flow rocks, and diorite (Figure 2). In the vicinity of the mine, these rocks have been termed the Mine Series. They belong to the Bourinot group, which has been assigned by L. J. Weeks to the Middle Cambrian. At the latitude of the mine, the Bourinot group is bounded on the northwest by the Stirling fault and extends eastward for two miles."

Jan 1, 1953

By D. Naden, D. J. King

"The high capital and operating cost of liquid-solid separation circuits in hydrometallurgical plants has led to an increased focus on the use of in-pulp systems for metals recovery in order to eliminate the need for solids washing and to reduce the need for liquid-solid separation.Carbon-in-pulp (CIP) has now been accepted in Canada and around the world as the leading process for recovery of gold and silver, replacing the Merrill-Crowe process and thus removing the need for CCD thickeners or belt and drum filters. The overall design of conventional CIP adsorption circuits was established in the late 1970s and it has remained substantially unchanged until now. Most of the development work since 'hen has been concentrated on improving methods of separating pulp and carbon and on reducing carbon losses during transportation and agitation.Resin-in-pulp (RIP) has been used for many years in uranium mills in the USA. However, most of the plants were built in the 1960°s and RIP was only chosen when liquid-solid separation of leach pulps proved very difficult. The plants are far from ideal as they have high resin losses and high maintenance costs. Consequently, there is room for improvement.Davy McKee has taken a fresh look at the engineering development of in-pulp contactors leading to a fundamental redesign of the adsorption units. The improved in-pulp technology uses a modification of the proven air-swept screen techno1ogy together with a new technique of process operation. The new contactor operates at high pulp throughput rates with high concentrations of carbon or resin in the recovery stages, resulting in a significant reduction in the contactor size over conventional design. As a result of this reduction in the size of the contactor by up to 80%, significant savings can be made in equipment and building costs. In addition, the plant 1s easier to operate than a conventional CIP plant."

Jan 1, 1987

By Henry Hengeveld

Are the IPCC results credible? The most recent IPCC assessment is??an admirable summary of research activities in climate science? US National Academy of Science 2001 report to President Bush Joint statement by Academies of Science from 17 other countries ? May 2001 ?The work of the?IPCC represents the consensus of the international science community on climate change science. We recognize IPCC as the world?s most reliable source of information?and endorse its method of achieving this consensus.?

Nov 1, 2002

By B. J. Morash

"The six mineable coal seams at Quintette Coal Limited (QCL) vary in thickness from 0.75 m to 9.5 m and include waste partings varying from 0.2 m to 4 m thick. They are highly faulted and folded in some areas and dip angles range from horizontal to 90 degrees. Due to this variation in thickness and orientation of the seams, several different mining methods are used to economically recover the coal. The key to QCL's success depends on the timely collection of detailed geology data and on mine planning which allows selection of the best method of mining to achieve maximum coal recovery with minimum dilution and cost. This paper will describe the various methods of mining employed and the criteria used to select them. IntroductionThe unique challenge in mining at Quintette Coal Limited (QCL) is to extract large quantities of coal and waste, from a complex orebody, with constricted areas for mining and waste disposal. This challenge dictates the mining of as many as four 10 m benches per year, through complicated coal structures, from three separate open pits with a total of 19coal seams. This total is made up of 5 seams at Mesa, 8 seams at Wolverine and 6 seams at Shikano (Fig. 1).Computer-aided mine planning and scheduling is carried out on a routine basis to ensure the prudent selection of methods of mining, to produce plans which ensure delivery of appropriately blended raw coals to the plant, and to coordinate disposal of large quantities of waste.Several methods of mining are applied simultaneously, and as a result coal and waste are released at different rates from twelve to fifteen mining faces. In order to ensure uninterrupted flow of material from excavators and to utilize the truck fleet effectively, a computerized dispatch system is employed.GeologyGenerally, geological conditions can be related to structural (faults and dip angle) and/or stratigraphic (coal seam and interseam waste thickness) sources"

Jan 1, 1988

By R. J. McLeod

"Grinding at Giant Yellowknife is done in two stages. The first stage consists of two ball mills in closed circuit will: mechanical classifiers, the classifier overflow goes to flotation. The tailings from this flotation circuit are separated into slime and sand portions, the slimes go to an additional flotation circuit while the sand portion goes to the secondary grinding mills.Milltronic automatic sound control units were installed on each of the two primary ball mills and put into operation September 3, 1966. After about two months adjustments to the control units the operators were taken off the grinding circuit on November 1, 1966. The operators duties were taken over by the automatic control units while miscellaneous work was taken over by the helpers in the mill. The labour saving by the installation is approximately $2250.00 per month.After a short period of operation it was apparent there was a slight change in grind. The screen analysis of the primary classifier overflows for the period May to August 1966 averaged 62.23% minus 200 mesh while for the period September to December 1966 averaged 62.0% minus 200 mesh. This is a slight coarsening of the grind. The change in the primary grind has manifested itself also in the screen analysis of the final grind. Before automation the final grind was 80% minus 200 mesh, while after automation it was 7 5% minus 200 mesh. A change of grind was also noted in the flotation concentrates. Before automation the screen analysis of the concentrates was 35% plus 200 mesh and 50% minus 3 25 mesh. A ft er automation it was 35% plus 200 mesh and 47 .5% minus 325 mesh. In other words the grind got coarser or perhaps we should say there was less overgrinding. Another significant change took place in the assays of the slime and sand portion of the primary flotation tailings. It was usual under manual control for the slime portion to assay higher in gold than the sand portion. The reverse is now true."

Jan 1, 1967

By Ahmad Ghahremaninezhad, Noelene Ahern, Yeonuk Choi

Arsenic (As) is a toxic element and is a major contaminant in the extraction processes of some metals (e.g. gold and copper). Due to the toxicity of arsenic species, its removal from As-containing streams from extractive metallurgy processes and safe disposal is absolutely necessary. For nearly complete removal of waste arsenic species from metallurgical process streams, it is required to have arsenic in its pentavalent state (As5+ species). This study presents an oxidation process for arsenic species with air or oxygen gas as oxidant. Activated carbon (AC) or other carbon based materials are used to catalyse the oxidation reaction. Air or oxygen gas is the only consumed reagent which makes the economy of the process very attractive. The oxidation reaction can be carried out at ambient conditions (room temperature and atmospheric pressure) in less than 24 hours.

Jan 1, 2014