Search Documents

By D. P. Goodall

THE development of the oil and gas resources of Western Canada is not, as many suppose, a new industry. For more than half a century an intensive search for these valuable products of nature extended from near the western edge of the Precambrian Shield to the Pacific coast, and from the International boundary north to the Arctic circle. The chief centre of interest to the oil prospector has, however, always lain in that region lying east of the first range of the Rocky mountains and confined largely within the boundaries of the Province of Alberta. Although there are many geological problems yet to be worked out in this Province, the oil-well driller has helped in no small way in determining sub-surface conditions and distribution of rock formations. The chief geological conditions as they affect the drilling of wells are generally re-cognized, and for this purpose the Province may be partitioned into three main divisions: first, the disturbed belt or foothills region extending along the eastern edge of the Rocky mountains; second, the Alberta geosyncline, a broad trough lying to the east of and parallel to the disturbed belt and from which the formations rise eastward to level off and form, third, the plains ? ? region, extending over the rest of the Province. A relatively small area in the northeastern part of the Province is underlain with Precambrian rocks and may be excluded from this classification, as it is of no interest to the oil prospector. The foothills, or disturbed belt, has presented the greatest difficulty to drilling, though it has produced the largest yield of oil within the Province to date. Within the foothills belt, the rock formations consist largely of hard shales interspersed with layers of abrasive sandstones, which wear out drilling bits at an alarming rate. The strata, in most flaces, dip steeply and are cut by numerous thrust faults. Although some o the faults have great displacements, their presence may easily be overlooked or the extent of the fault misinterpreted. Many a prospect well has been located on what appeared to be a suitable geological structure only to find, after drilling through a normal succession of rocks for 4,000 feet or more, that the drill had passed through a major fault plane to a younger formation than that in which drilling was started. Only a repetition of formations already drilled could be expected at greater depths.

Jan 1, 1942

By C. Kim

The integration of three-dimensional (3D) data with infrared thermography has received much attention for its potential use as input data for building energy simulations. Therefore, researchers have proposed methods to integrate 3D data with infrared thermography obtained by different sensors. These studies show the potential of the integration of 3D data and infrared thermography using various systems. However, these studies have ignored property aspects of infrared thermography, such as the low resolution of infrared thermography and external environmental influences. Thus, their proposed methods to integrate 3D data and infrared thermography are inadequate because these problems can affect the resulting building energy simulation. This research proposes a framework that integrates infrared thermography and 3D data while accounting for the resolution and shadow effect of infrared thermography. The proposed framework consists of three steps. In the resolution enhancement step, bi-cubic interpolation is proposed. In thermal data correction from the shadow effect, the shadow area is detected from the visible image, and then the shadow effect is removed from the registered infrared thermography. Finally, enhanced infrared thermography is mapped to the 3D data obtained by a laser scanner. The performance of the proposed framework was evaluated using test images obtained from a building in operation. The experimental results show that the proposed framework provides a 3D thermal model that is useful and accurate in simulating building energy. It is expected that the 3D thermal model can be used for accurate energy simulation of existing buildings. In addition, the proposed framework can be applied in defect detection for buildings. Furthermore, this novel approach enhances infrared thermography using visible images.

Aug 1, 2013

By J B. Maughan

Gas and oil seeps have been known in Quebec for more than one hundred years. These occur in three main areas which contain sedimentary rocks with a total thickness estimated to vary from 6,000 to 20,000 feet. The strata in these areas are similar in many respects to those in producing areas of southwestern Ontario and the Appalachian basin, and the prospects for finding and developing commercial reserves of oil and gas in Quebec would therefore also appear to be favourable. Little of the exploratory drilling to date has been con-ducted in a systematic manner, and most of the drilling has utilized improper or inadequate equipment. Many wells have also failed to adequately test and fully evaluate the principal zones of interest. Relatively high drilling costs have hindered systematic exploration; however, with improved portable equipment, it is expected that future wells can be drilled with greater efficiency and at less cost. Most of the mineral rights in Quebec are held by the Provincial Government, and acreage can still be leased in large blocks on favourable terms.

Jan 1, 1964

By V. C. Wansbrough

First, permit me to say with what very great pleasure we find ourselves assembled in this most ancient and honourable city of Quebec. It is a city which we deeply respect as the fountain-head of the culture of French-speaking fellow citizens, and the seat of government of a province which is steadily recording new achievements in Canadian mining. Such achievements prove what can be accomplished when enlightened and progressive government policy, technical and scientific competence, and private initiative pull forward together in harmonious rhythm. It is a most happy and auspicious event also that the guiding control of the affairs of the Institute and of the fine traditions of provincial administration have for the past year been united in the person of our honoured President, Dr. A. O. Dufresne. This year, again, we have bad prepared for us by our hosts a splendid programme of technical sessions and social entertainment. Each year we pay an unspoken compliment to the Institute, expecting as a matter of course nothing but the highest standards in both these spheres. In its annua1, semi-annual, and regional meetings, in the constant activity of its local Branches, the Institute continues with marked success to perform its great dual service, social and educational. We are all its beneficiaries to the extent to which we choose to profit by participation in its affairs. But, one imagines, to none are the advantages of Institute membership more valuable than to young men embarking on their professional careers.

Jan 1, 1951

"Introduction The first documentary record of coal nurung on Vancouver Island was that of the Hudson Bay Company operations in the Suquash area in 1836. Between 1836 and 1862, the Hudson Bay Company mined some 65,000 tonnes from this Suquash field and the Nanaimo coal fields discovered in 1851. However, systematic mining of coal did not take place until the Hudson Bay Company holdings were sold to the Vancouver Coal Company in 1861, and a rival company under Robert Dunsmuir was established in 1869. These two interests under various organizational names and jointly as the Canadian Collieries (D) Ltd. (1928) developed and exploited the coal seams of the Nanaimo and Comox Basins from 1852 to 1966. Because of the proximity of the coal outcrops to tidewater, the coal was readily marketed to ocean-going and coastal ships for fuel. However, during the turn of the century the main market was to meet the demand of the developing cities along the west coast of Canada and the United States for residential and commercial heating. Island-based copper smelters and brick factories, and the coming of the railroads motivated by steam engines increased the demand. This economic success of the industry continued until 1922 when a peak production of over 1,750,000 tonnes was reached. Following 1922 labour unrest in the industry, which affected the certainty of supply, and the availability of alternatives in the form of California petroleum and mainland coal combined to cause a rapid and steady decline in the demand for Island coal. In spite of post-and pre-wartime prosperities the trend could not be reversed. Serious coal mining phased out in the Nanaimo area in 1939 and in the Comox area in 1967. puring the 114 years in which the industry flourished over 75 million tonnes of coal were mined from more than 30 mines and a minimum of ten new mining communities were established on Vancouver Island."

Jan 1, 1985

By George Kellock

In presenting this paper for discussion at the Western Annual Meeting to be held in Edmonton, it is with the idea of creating a full and general discussion by the mining men in the Province as to the best way to eliminate, or at least hold down to a minimum, the dangerous coal-dust which is made in mining pitching seams in our Alberta mines by the chute method. Also, an alternative method is outlined, whereby the percentage of lump-coal mined can be increased, and the mining costs reduced-although the paper does not go into any detailed consideration of costs. The general trend of mining practice and lay-outs is at present towards mechanization, and the results being accomplished by the substitution of machines for manual labour are fully justifying the changes. In the technical mining journals, there are published from time to time papers dealing with a variety of methods of mining, which are descriptions of actual operations, and a great deal of interesting and valuable data is given as to the comparative values of the different methods, insofar as the percentage of grades of coal produced, the cost of production, etc., are concerned; but the mechanical methods described in these papers are nearly always suitable only for flat seams, or seams with a very low inclination.

Jan 1, 1929

By J. F. Henderson

THIS paper relates to an area of more than 5,000 square miles in the Northwest Territories extending north from Great Slave lake and including-the Yellowknife, Beaulieu River and Gordon lake areas. Within the last three years much interest in the area has been created by the discovery of remarkably rich gold-bearing veins and the realization that thousands of square miles of unprospected ground are underlain by rocks like those in which the veins have been found. Probably there were more prospectors in this area in 1938 than in any other part of Canada. The area lies 650 miles north of Edmonton, and 425 miles north of the terminus of the Northern Alberta railway at Waterways, Alberta. The Athabaska and Slave rivers provide an excellent water route from Waterways to Great Slave lake for large oil and wood burning boats and barges which operate from the latter part of May to October. The only portage is around a 16-mile stretch of rapids on the Slave river between Fort Fitzgerald and Fort Smith. The town of Yellowknife, on the north side of Great Slave lake, has sprung into existence during the past year and is the centre for distribution of supplies for the Yellowknife-Beaulieu region. The Con-Rycon and Negus gold mines, which came into production in September, 1938, and February, 1939, respectively, lie about two miles south of the townsite. Excellent airplane service is available from Edmonton to Yellowknife and from Yellowknife to all parts of the area. The prospector and mining operator have come to rely almost entirely on the airplane for supplies and for the transportation of personnel, camp equipment, and canoes from Yellowknife to localities selected for intensive prospecting.

Jan 1, 1939

By P. H. Tolcher

Canada, as the Free World's largest mine producer of zinc and the third largest mine producer of lead, has a vital interest in the future growth in demand for these metals. This paper traces the development of lead and zinc consumption in the last two decades, both on a total-Free-World basis and by major market areas. How Canada, as a major mine producer, has shared in this growth is also indicated. In addition, future consumption for both metals in the current decade of the 1970's is fore-cast. The demand these projections will make on Free World mines, particularly on Canadian mines, is examined. Some of the opportunities and challenges the Canadian mining industry will likely face during this period are also dealt with.

Jan 1, 1971

By Russell McIntosh

"The Madsen mine is in the southeastern part of Baird township, in Red Lake area, Ontario. It lies about 6 miles southwest of the town of Red Lake, with which it is connected by an all-weather road.The Madsen Red Lake Gold Mines Company was formed in March, 1935, to take over the holdings of the Falcon Gold and Jomac Gold syndicates. During 1935 an4 the early part of 1936 No. 1 shaft was sunk and drifts driven on four levels, all on a narrow quartz vein in a granite dyke.In July, 1936, the Austin zone was discovered about half a mile north of No. 1 shaft by Austin McVeigh, a prospector employed by the Company. Diamond drilling showed that the zone included an orebody worth development, and in 1937 No. 2 shaft was sunk, three levels opened up and sufficient ore outlined to justify the installation of a mill. Milling commenced in August, 1938, at the rate of 300 tons a day, which was later increased to 400 tons a day.The total production from 1938 to 1946 was 1,116,307 tons from which gold and silver having a value of $9,949,010 were recovered. The gold produced ranged from a minimum of 0.1910 oz. a ton in 1939 to a maximum of 0.2827 oz. in 1944. The average grade in 1946 was 0.2345 oz. to the ton."

Jan 1, 1954

By G. S. Headley

At the Sullivan Mine, recent experience with sulphide fires, locally referred to as " hot muck", has necessitated extensive modifications to pillar mining design and operating procedures. Potentially hot pillars are now being designed and mined to prevent fires. Unusual safety hazards and difficulties are encountered in working with, and adjacent. to, existing pillar fires. Operating procedures developed for these conditions have proved successful for safe and continuing production. These changes have minimized the impact of hot ore on current operations and have promise for an improved future.

Jan 1, 1977

By Harold Hopkins

THE Wright-Hargreaves mine is one of a group of seven mines long active in the Kirkland Lake district, Ontario. Detailed geological reports and maps covering the area have been published by the Ontario Department of Mines (1,3)t. Though all these mines work several productive veins there is one vein which is common to all and is known as the North Vein of the camp?not that it is the most northerly vein mined, but it is the more northerly of the two major veins of the camp. At the Wright-Hargreaves mine there are in all ten important producing veins, and most of them have a N.60°-65°E. strike and in general a steep southerly dip. It is a common belief that most of these veins lie along faults but it will be shown that whilst this is true of some of them it is not true of all, and also that a vein may lie in a fault along part of its course and elsewhere fill a fracture in line with the fault, this being a consequence of rotational movements that took place during faulting. The paper describes the history of faulting at this mine in particular, makes observations on the principal pre-ore fault, and describes the method used in solving the movements on the post-ore faults. Other details of geology are not discussed except to mention here that our main veins lie almost entirely in the syenite porphyry stock except on lower levels close to the east boundary of the property, where the North vein leaves the porphyry to enter the greywacke.

Jan 1, 1940

By O. Lundhede

Today, systems and machinery usually are designed to meet only one specific customer?s requirements. One reason for this is that underground automation and smart functions are often developed tightly together with a customer. This is natural, since risk and cost can be shared between the customer and the supplier. Nevertheless, when the automation product develops and the market increase this will cause problems: The highly specialized products will not fulfill the next customer?s demands. In order to cope with this problem, Atlas Copco works towards a common platform. Instead of designing solutions for specific customers, we will lift the abstraction and focus on standardized modules. These modules, or function blocks, can then be combined in a large variety of configurations. The benefits of combining modules into products are, for example: increased flexibility when options are available for many machines; easier commissioning and maintenance since less different spare parts and tools are needed; and easier operation since the user interfaces have a similar look and feel. This paper will present the ongoing work towards standardized modules. We will discuss how our Rig Control System (RCS) allows for modular design at Atlas Copco. RCS has number of standardized modules that are used in different surface and underground mining and tunneling equipment. These modules are also used for optional products such as, drilling, radio-remote control, and telematics systems.

Aug 1, 2013

By D. Bernard

Over the last decades, the wrought aluminum casting industry has made significant progress with regards to process consistency by the introduction of new technologies in the field of liquid metal processing and casting. These technologies, combined with the application of best practices, have led to increases in productivity as well as better process performances and product quality. The competition in the addedvalue aluminum products (by opposition to P1020 production) is, however, very strong and involves players that did not hold a major role five years ago but who are now exerting a strong competitive pressure on our industry even sometimes from far abroad. There are still technical and technological challenges remaining in the different areas of aluminum casting production, amongst which metal pre-treatment, furnace operations, in-line treatment and casting hold a predominant influence. The comprehension of the contribution of each individual process step to the entire process chain is a key element and must be considered in future process optimisations. This paper presents the technological position of the casting industry and tries to highlight areas where further progress can be made.

Jan 1, 2006

By T. E. Warren, K. W. Bowles

"IntroductionTHE PROBLEM of producing synthetic liquid fuels from coal and other raw materials is of increasing importance in Canada as well as in the United States. This is due, to a large extent, to the continually increasing demand for gasoline and other liquid products which are now obtained solely from petroleum. The United States has reached a position where domestic supplies of crude petroleum must be augmented by imports and Canada is still a long way from self-sufficiency. In the event of war, there might well be an immediate need to find supplementary sources of liquid fuels. It is, therefore, expedient to consider alternative sources of production now -well in advance of the time when supplies of petroleum may prove inadequate to meet requirements.The purpose of the present paper is to give a short review of the history of liquid fuel production from coal, to describe briefly the research sponsored by the Federal Government on the coal hydrogenation process, and finally to evaluate the present status and future trend of the synthetic fuel industry, with special reference to necessary research work.History of the Oil-From-Coal IndustryThe history -of coal liquefaction began in 1913, in Germany, with the work of Frederick Bergius. His first approach to the subject was not deliberately planned."

Jan 1, 1952

By D. E. Keeley

lntroduction Some years ago it was general practice in Canadian mines to use the best timber available, just as it was cut from the tree. Later, to prevent 'borers' from getting into the wood while stacked in the yard, the bark was peeled off, cleaned up carefully, and burned to eliminate a breeding ground for these and other destructive insects. This practice of good housekeeping also decreased the hazard from fire in scattered bark. A few years after damage by borers had been minimized, it became apparent that increased temperatures in the mines, occasioned by deepening operations, were being accompanied by rapid growth of fungus and by decay in timber underground, greatly shortening its life. In places on upper levels where the air temperature was below 50 deg. F., untreated timber retained a large proportion of its strength for ten or more years. In other places on these levels, however; its life was short and it developed much dry rot and merulius lacrymans. In these latter places and on lower levels in the mine where temperatures ranged from 50 to 60 deg. F., approximately, the wood became infested with extensive growths of this white fungus. This development was accompanied by the production of millions of spores. Spread of infection was due mainly to the transfer of spores from the warm lower levels to the cool upper horizons by upcasting ventilation currents. So serious did this become that about twenty years ago Lake Shore, Hollinger, and McIntyre Mines decided to investigate the use of wood preservatives and the plant necessary to treat timber.

Jan 1, 1949

By Gurupraveen Ramanathan

Shallow-dipping orebodies (45°–60° dip) present significant challenges for underground longhole stoping, particularly due to limited gravity flow, drill misalignment near the footwall, increased potential for dilution from hanging wall overbreak, and deviation from drill string sagging at shallow angles. These geometrical and operational constraints often lead to unblasted ore wedges and excessive overbreak when standard practices are applied. This study develops a structured, data-driven framework to optimize longhole stoping in such conditions by integrating five key focus areas: (1) mining method selection, (2) stope and drift design, (3) drill and blast optimization, (4) equipment selection, and (5) performance evaluation. The suitability of longitudinal longhole stoping was validated for narrow vein geometries using orebody analytics and prior case studies. Geometric modeling was employed to determine optimal stope height (15–20 m) and stope width (1.5–2.5 m), with drift widths adjusted based on orebody dip to maintain drill access and minimize unbroken ore. Drill and blast design emphasized sequential blasting over multi-ring methods to improve void control, reduce wall damage, and enhance fragmentation. Specific burden and spacing guidelines (e.g., 1.8–2.3 m burden; 2.5–3.0 m spacing) were applied based on stope width and dip angle, and patterns were selected based on geometry—dice-5 for narrow stopes, and 3-hole rows for wider stopes. Drill rigs—including top hammer and ITH models from Sandvik, Epiroc, Boart Longyear and CMAC-Thyssen—were evaluated for compatibility with drift dimensions and alignment accuracy. Equipment was matched based on dip, drift width, and the ability to access the footwall at shallow angles. Sensitivity analysis quantified how changes in geometry, drilling accuracy, and blast design affect ore recovery, dilution, and operating cash flow. Results show that tailored drift and stope geometries, combined with proper blasting and rig selection, can boost ore recovery to over 95% and reduce dilution to below 5% in optimal conditions. This methodology offers a practical and economically optimized solution for shallow-dip mining scenarios.

May 4, 2025

By Gene O. Cowie

"Zinc, which once enjoyed an unchallenged position in the field of decorative applications, has lost a substantial share of its markets to other materials, particularly plastics. This turn of events has led the zinc industry to explore new market areas, particularly those applications where the engineering properties of zinc can be utilized. This paper gives an overview of the zinc industry's efforts to develop the data base and product development technology which have enabled zinc alloys to emerge as engineering materials. It also indicates those areas in which the research facilities of the zinc industry must be employed to ensure that zinc alloys keep pace with developments in competitive materials and processes.The Materials RevolutionThe development and utilization of new materials and manufacturing processes progressed for centuries by evolution. Recently it erupted into a revolution, which may become as significant as the industrial revolution. The materials revolution has impacted upon many industries, but none has been affected more traumatically than the North American automotive industry. The plight of that industry is of great importance to us because their problems have, to a great degree, become problems to the zinc industry.Much of the impetus behind the automotive trauma came from the battery of motor vehicle regulations promulgated by the United States government in the 1970s. These regulations required that the efficiency of passenger cars, in terms of miles per gallon, be approximately doubled in ten years. In view of the fact that major changes in the automotive world require three years of lead time to implement, the industry was left with only seven years to perform the task. The automotive industry was simultaneously required to make progress in other areas, such as reduced emissions, reduced cost of repairs and increased levels of occupant safety. These added demands not only diverted some of the available resources away from efficiency goals, they often ran in direct conflict. For example, when you are required to provide a front bumper which will absorb the energy of a 5-mile -per-hour barrier collision, you must add both hardware and structure to the vehicle. This adds weight, and increased weight reduces miles per gallon."

Jan 1, 1983

By G. A. Gross

DURING the past 5 years a large amount of money and effort has been expended in exploration of iron-formations and in testing their suitability for beneficiation. Beds of ferruginous material are numerous and widely distributed in the Precambrian rocks of Canada and practically all of the known iron ranges or belts have been examined to a limited degree at least in an effort to evaluate their potential as sources of iron ore. A number of favorable beds have been selected for mining on completion of surface sampling, diamond drilling, extensive metallurgical testing and economic studies, and many other ranges are being studied. There are still a great many iron-formations that have not been evaluated by modern concentration methods and their regional extent is not fully known. The iron-formations are easily located by airborne or ground magnetic surveys but the main task in finding a mineable ore-body of this type amounts to locating a bed sufficiently large for mining which consists of material that can be concentrated economically by modern beneficiating methods. The ease with which an iron-formation can be concentrated to give a marketable ore depends primarily

Jan 1, 1961

By V. Gaudreault

Rio Tinto Alcan (RTA) has three smelters that use the Alcoa P155 technology: two in Canada (Grande-Baie and Laterrière, Saguenay, QC) and one in the United States (Sebree, Kentucky). The oldest RTA P155 smelter was built in the 1970s (Sebree) and had an initial current intensity of 155 kA. In the 1990s, RTA installed an amperage booster in Grande-Baie smelter to increase cell productivity. Since then, RTA has continuously pushed the limit of this technology and the target amperage that was 195 kA in 2005 has been increased to 210 kA in 2010.This article describes the successful plant-scale trials to increase current intensity from 195 kA to 210 kA, and the key performance indicator results. It demonstrates RTA's technology leadership to undertake such a development with its Brownfield smelters.

Jan 1, 2011

By W M. Cameron

Geophysical studies have extended seaward in recent years, and the important discoveries which have been made have led to a better understanding of geological processes. A present source of certain minerals, the sea will eventually serve as an important source of desalinated water. The continental helves, in particular, represent a potential mineral resource. The expansion of Canadian oceanographic effort that is now underway will eventually lead to the exploitation of the wealth beneath the sea. THE subject of this symposium, which emphasizes the word "geophysics," the specialties of the speakers who are contributing and the nature of the audience at first made me believe that I, a a physical oceanographer, would be out of place. However, I shall undertake to classify myself as a geophysicist, and shall arrange my remarks on my specialty o that they might be of interest to those of you who are predominantly geologists, metallurgists or mining engineers.

Jan 1, 1963