Search Documents

By Shek N. Lau, Nicola Samman

"Enclosed gear cases on board heavy mining equipment have traditionally been lubricated with regular heavy duty gear oils. However, equipment manufacturers, have recommended the use of an ISO-1000 gear oil for this application to ensure adequate lubricant film strength, especially at the higher end of the working temperature range. The majority of these ISO-1000 gear oils are based either on residual/asphaltic oil or synthetics, primarily higher viscosity polyalphaolefins. Although the performance of these lubricants has been satisfactory, they suffered other shortcomings that equipment users have lived with over the years.The major requirement at the user’s mine was to provide lubrication for the shovel Hoist gear case. Within such a gear case design, the gears and the roller bearings, that have different lubrication requirements, are lubricated with the same lubricant. Several lubricants were used, light gear oils as well as the recommended ISO-1000 heavy gear oils. On the one hand, the lighter oils performed adequately for the lubrication of the bearings that formed part of the enclosed gear system. These lighter oils did not perform as well for the lubrication of the gears due to their lower viscosities, resulting in shorter gear servicelives.On the other hand, the ISO-1000 gear oils performed well for the lubrication of the gears, but were too viscous to creep into the bearing elements to lubricate them adequately, especially during the cold northern Canadian winters. This resulted in catastrophic bearing failures and secondary damages to the gears.The challenge, then, was to formulate a lubricant which met the 1000 cSt at 40°C viscosity requirement as stipulated by the equipment manufacturer, while satisfactorily lubricating the bearings at the full working temperature range. This was achieved by the development of a semi-fluid grease lubricant, which has proven in field trials to give adequate performance in this application for the lubrication of both the bearings and gears down to -40°C.This product met the equipment manufacturer’s performance criteria and resolved, to a large extent, leakage of the lubricant through seals experienced with the use of conventional and synthetic gear oils.Although the main performance criteria of the fluid was its capability to lubricate the “Hoist” gear case, it was also used during the field trial in other gear cases on board the shovel to test its full capabilities.This unusual alternative lubricant was field tested and evaluated for more than two years. Based on this assessment, the product was reformulated to improve its fluidity, slumpability and the settling of debris/wear metals to the bottom of the gear cases. This reformulated softer grade, a semi-fluid grease, has been performing satisfactorily for more than eight months and is still undergoing longer term assessment."

Jan 1, 1996

By Chris Twigge-Molecey

"Over the last 50 years there has been a dramatic evolution in the metallurgical engineering field in Canada. In the 60s the field was dominated by large American and UK groups, often selling major process and equipment packages. The local content was limited to wrap around facilities and the civil and structural work. The mining and metallurgical companies had strong internal teams to lead these projects. Over the decades and business down cycles the large foreign contractors disappeared or re-structured and the mining companies largely shed their engineering and project management groups. The resulting gap was filled by a cadre of local specialist engineering companies, some of whom have grown to be world leaders in the field. The paper traces this evolution and examines the underlying causes and consequences."

Jan 1, 2015

By W. T. Irvine

"The H.B. Mine, a zinc-lead operation of the Consolidated Mining and Smelting Company of Canada Limited (Cominco), is in south central British Columbia, on Sheep Creek, a west-flowing branch of the Salmon River. It is 3 miles by road from B.C. highway No. 6, 30 miles south of Nelson, B.C., with an excellent highway connection to the smelter city of Trail, 35 miles from the mine. The nearest permanent settlement is the village of Salmo, 7 miles distant by road. The mine is situated along a belt containing other important zinc-lead deposits, including those of the Canadian Exploration Company, 3 miles to the south, and the Reeves MacDonald mine, 9 miles distant again to the southwest.Deeply oxidized outcrops were located in 1907 on the north side of Sheep Creek valley by two prospectors named Horton and Benson. The property was given the name H.B., after the two discoverers, and there commenced a long and intermittent series of mining operations designed mainly to develop and extract oxidized lead-zinc ore. In 1925 a determined attempt was made by a British syndicate to develop a large tonnage of sulphide ore, but this ended in failure after some 3,000 feet of lateral development had been done. In 1927 Cominco acquired the mine, but it lay idle until 1946 when a geological study was followed by a program of surface drilling which encountered extensive sulphide mineralization. An underground development program revealed more details of the deposit, and sufficient ore was found to warrant construction of a 1,000-ton mill. Mine preparation and mill construction were completed by early 1953, but production was deferred due to low metal prices. The mine was finally brought into production early in 1955."

Jan 1, 1949

By N. Behnood, W. Pascheto

"Laboratory wear tests are important tools that can be used for the evaluation of materials for wear applications and mitigation of wear problems in the mining industry. However, laboratory test parameters must be fully characterized and test results must be carefully interpreted if a material selection is to be made. Failure to do so may lead to erroneous conclusions. Suitable lab-oratory tests are valid only if they reflect the field conditions to which materials are subjected. Therefore, it is important to know, in detail, the field conditions, as well as the wear test techniques being considered. It is important to recognize the limitations of the various wear tests and the wear test data published in the literature. This work will review present wear testing technology, including the various wear tests avail-able, wear test equipment and test limitations. Several wear test procedures will be related to common equipment used in the mining industry.IntroductionThis paper will concentrate on non-lubricated wear mechanisms, because they are the most costly to the mining industry. Very frequently we are faced with the task of selecting materials for wear applications or improving existing systems that are giving poor performance. There are plenty of examples in the literature of practical wear cases and ranking of materials for wear applications. It is also very common to find materials manufacturers’ data -sheets listing wear tests results by comparing their materials performances against those of competitors. Much of the published wear data lack the description of the type of wear test, test parameters and the type of wear mechanism to which the data should be applied (if any).Before considering wear test data for a specific problem one should ask which type of wear mechanism is involved? What type of test and what test parameters were used to produce the results? Even if the type of wear tests and parameters are known, how accurate and useful are the published wear data? How are the results related to a particular type of wear? It is important to point out that even the standardized wear tests, such as those in ASTM standards, have limitations. Such limitations are recognized and clearly spelled out in the standards themselves. Basically, wear tests may lead to erroneous results if the test is not able to repro-duce the same wear mechanisms encountered in the field. Therefore, the use of published results may be helpful, as a starting point, but may be of little value for a final material selection.This work will discuss the main types of non-lubricated wear mechanisms encountered in the mining industry. In addition, it will discuss the many wear tests available and their correlation with the various types of wear mechanisms. The limitations of several standardized wear tests and the limitation of using published wear data will also be discussed."

Jan 1, 1997

By J. H. Baek, S. Alexandrovskii, D. W. Lee, B. K. Kim

Nano-phase titanium carbide was synthesized by Mg-thermal reduction process using a novel route of Mg-thermal reduction. The processes are based on I) feeding of TiC14+CxC14 x = 1, 2 ) solution into liquid magnesium, 2) Mg-reduction of metal chlorides, 3) TiC formation by the reaction of released Ti and C atoms, and 4) vacuum separation of residual liquid phases of Mg and MgCl2. In this study, the process for titanium carbide production with composition close to stoichiometry and the minimum content of impurities was optimized with the various process parameters such as concentration of initial solution, its feeding rate and reaction temperature, as well as a kinetic study.

Jan 1, 2004

By Michael Schindler

Uranyl mineral dissolution appears to be complex, affected by factors such as solution pH and the presence of various cations in solution, and sometimes involving formation of secondary surface precipitates. Such secondary precipitates potentially could armor the underlying uranyl mineral surfaces from further dissolution. A detailed understanding on the formation of secondary precipitate is therefore essential for predictive modeling of radionuclide fate and transport in the subsurface. Several types of secondary precipitates on the surface of uranyl minerals were examined using Atomic Force Microscopy, Scanning Electron Microscopy, and, Xray Photoelectron Spectroscopy.

Aug 1, 2010

By T. Guan, G. Fu, X. Zhou, L. Deng

"Currently, tailings water is required to be recycled in minerals processing plants. When the flotation tailings water of complex copper-sulfur-tungsten polymetallic ore is reused to the flotation of copper-sulfur ore, a portion of tungsten would be lost in copper concentrate or sulfur concentrate due to the addition of the collectors used for oxidized ore which are also effective for the sulfide minerals in the process of tungsten flotation. At the same time, the technical index of copper concentrate and sulfur concentrate would be seriously affected by tailings water. Our experimental researches of many years show that the copper concentrate with a grade of 18.36% Cu at a recovery of 76.67% is obtained for the raw ore containing 0.60% Cu, 18.99% S, 0.16% WO3 in small locked cycle test using recycled water, through simple pretreatment of the tailings water from tungsten flotation and adding special regulator CW and new tungsten collector TM. The result is close to the performance without using tailings water. And, in the continuous pilot experiment which was continuously conducted for 4 days with the same technology, the following results was obtained: the copper concentrate with a grade of 21.74% Cu, the recovery was 71.55%; the sulfur concentrate with a grade of 45.16% S, the recovery was 80.10%; the tungsten concentrate with a grade of 42.63% WO3, the recovery was 54.62% relative to raw ore (the recovery relative to scheelite was 76.47%). The throughput of the continuous pilot experiment is 1.0~1.2 t/d, and the raw ore contains 0.56% Cu, 18.80% S, 0.14% WO3 on average.INTRODUCTIONMining industry is one of the most important developing fields, it supplies raw materials for industrial production as well as discharges much waste water. Tailings water is the main source of beneficiation waste water, it would result in severe environmental pollution if discharged directly. Generally, the tailings water would bring undesirable effect on flotation index after simple pretreatment by lime (Kalin, Fyson, & Wheeler, 2006). On the other hand, the treatment of tailings water through ion-exchange (Cui & Liu, 2015) before recycling is of high cost. Generally, in the flotation of Cu-S-W polymetallic ore, when the tailings water from tungsten flotation is treated simply by lime and recycled to the flotation of sulfide minerals, the flotation index of sulfide minerals decreases, and a portion of oxide mineral would be lost in the sulfide concentrate. As a result, the recycle rate of this kind of tailings water is relatively low, some of the tailings water is discharged after simple treatment and then environmental pollution is caused subsequently. One of the effective ways to improve beneficiation performance and increase the recycle rate of tailings water is to conduct research on developing recycle technology for flotation tailings water of complex copper-sulfur-tungsten polymetallic ore."

Jan 1, 2016

By R. T. Erskine

"The No. 6 orebody is located 6 miles from the main op.eration of Brunswick Mining and Smelting Corporation Limited and includes open-pit and primary gyratory crushing facilities. Ore is transferred by truck to the secondary crushing facility at the main plant. About 3,500 tons of ore per day are crushed to minus % in. and ground to 68 per cent minus 400 mesh in rod and ball mills for flotation feed. Conditioning and aeration precede rougher flotation, and four stages of cleaning bring concentrates to a grade of 42 per cent Pb + Zn + Cu. Middling products are reground and refloated in a secondary flotation circuit, producing a cleaner feed and a final tails product. Primary bulk concentrate is treated with sulphur dioxide and steam-heated to l 70°F and the majority of the gangue is floated off, leaving a product that assays 57 per cent combined Pb + Zn + Cu and is suitable for marketing. This material is thickened, filtered, dried and loaded into railway cars for shipment to the smelter. Reagent use on flotation is conventional, with many compromises in dosage required to maintain the recovery of lead and zinc in the most advantageous proportions. Many refinements in the flowsheet have been made since start-up in 1966, and more may be made as laboratory and plant testwork indicate possible improvements."

Jan 1, 1971

By Tom Gaines, G. S. Brant, J. G. Debanne

"AbstractThe Bonnie Glen oil field, one of Canada's largest, lies about fifty miles southwest of Edmonton, Alberta. One hundred and thirty-eight wells have been completed in this field since its discovery in January, 1952. Five different procedures have been used in completing the producing wells.The reservoir is an Upper Devonian biohermal reef with good porosity and uniformly high permeability. The top of the reef is quite flat but the flanks slope at angles approaching 20 degrees from the horizontal. The reservoir has a gas cap with a maximum thickness of 400 feet, an oil column of 300 feet, and a :porcus aquifer of over 300 feet. The reservoir pressure is now 2,400 pounds per square inch gauge at datum ( -4100 M.S.L.).Because of the high permeability and the high •pressure, lost circulation and resultant blowouts are a particular hazard in drilling at Bonnie :Glen field. To reduce the dangers of blowouts, it is general practice to run casing to the top of the reef. If the reef is encountered 'high' it was usual practice to run a liner and perforate for completion. Wells penetrating the •reef below the gas/oil interface were either completed in open hole or through casing perforated opposite the oil pay, with the former method more frequently used. Eight wells were completed by the Humble-Otis permanent-type completion, and recently five high wells were completed open hole with the gas •cap exposed. This latter completion, 'tubing submergence', has proved highly satisfactory thus far.The open-hole type of completion is cheaper than the liner perforation method and results in better well performance. More experimentation and data are needed before the tubing submergence method can be recommended unqualifiedly. but all evidence thus far favours its use in reef reservoirs."

Jan 1, 1955

By A. Boehm

"For recycling LD slag into the steel making process, the phosphorous containing calcium silcate phases have to be removed from iron oxide phases. One possible technical solution could be magnetic separation in a wide range of susceptibilities from ferromagnetic to paramagnetic. To check the feasibility of magnetic separation the distribution of the magnetic susceptibility in size classes as well as the liberation of the phosphorous containing phase were evaluated by a new method combining two dimensional physical property analysis with QEMSCAN analysis. The particle size classes of energy controlled comminution products were subdivided into fractions of defined magnetic susceptibility using a hand magnet of well known field properties (pick up method). On the one hand the susceptibility classes were wet assayed on the other hand analyzed by QEMSCAN followed by data evaluation using iDiscover 5.3.1(FEI), which was adapted to the data structure of two physical properties (size and magnetic mass susceptibility). The results allow the comparison of mass based (3D) cumulative distribution of grades from the wet assays with the area based (2D) distribution from QEMSCAN analysis, in order to control a systematic (size dependent) stereological error for this special type of material. As the physical separation property forms a crucial parameter the results from the liberation analysis by QEMSCAN can be interpreted more profound with respect to an expectable separation result. Once the various mineral compositions of the particles are assigned to the physical properties the Henry Reinhardt chart serves to predict the best possible separation result and thus the feasibility of a separation technique.INTRODUCTIONThe two Austrian steel plants operated by voestalpine AG produce about 650,000 t (voestalpine 2014) of LD slag in the course of steel production from pig iron according to the basic oxygen process blowing oxygen in the converter by an oxygen lance. The process is also known as the Linz Donawitz (LD) steelmaking process. By the addition of lime (CaO), carbon, phosphorus, silica, manganese and sulfur, which are present in the molten pig iron, shall be oxidized and bound in the slag either as oxide or silicate phases, or leave the slag in the gaseous phase (CO). The average chemical composition of the investigated LD slag is given in table 1."

Jan 1, 2016

By R. St. C., G. E. Morris, M. Zbik, Smart

Effective flocculation and dewatering of slurry streams containing clays (particularly kaolin and smectites which are often <200nm in lateral dimension) is becoming increasingly urgent. Release of water (often >75 wt%), for recycle and reduced make-up water consumption, from slurries in tailings streams and dam beds is usually slow and incomplete. Changes in settling rates and solids density of tailings containing clays can be achieved in practice by changes in pH, dissolved cations and flocculant additions. To achieve fast separation of clays from water and minimization of retained water, individual particles need to be bound in the initial stages of thickening into large, high-density aggregates, which may sediment more rapidly with lower intra-aggregate water content. Quantitative STIMAN (STructural IMage ANalysis) cryo-SEM imaging, shows that the structure of aggregates formed before flocculant addition has a determinative effect on these outcomes. Without flocculant addition, 4 stages occur in the mechanism of primary dewatering of kaolinite: initially separate particles and aggregates are dispersed (<0.3GP, where GP is the gel point); a partially-gelled chain network then forms linking particles edge-edge (EE) still well below the OP but remains largely suspended; after an induction time, this network structure rearranges from EE to face-face (FF) contacts densifying, compacting and dewatering the aggregates with settling rates well above Stoke&apos;s Law estimates for >20µm particles or aggregates; the GP is rapidly reached during settling producing a network spanning the vessel with compressive strength. This sponge-like structure with EE oriented particles limits slurry dewatering because the steric effect in the resulting partially-gelled structure is much more dominant than the electrostatic effects predicted by DLVO theory. Van der Waal&apos;s forces at very close distances, as particles slide across each other, may be responsible for the EE to FF change in structure. In this way, the previously extended network contracts, and when the solid volume fraction is low, the continuous network breaks apart forming aggregates and aggregate associations as flocs which arc able to freely settle. These densified aggregates settle at increased rate, give lower bed density and retain less water after drainage. With flocculant addition, the internal structure and networking of the pre-aggregates is largely preserved but they are rapidly and effectively bound together by the bridging action of the flocculant(s). The STIMAN analysis shows that there is a inverse correlation of intra-aggregate porosity (and void permeability) with Darcian permeability (and extent of dewatering) whereas there is a strong positive correlation of Darcian inter-aggregate permeability with settling and primary dewatering rate.

Jan 1, 2004

By K. Kudo

Magnesium rods of 99.95% purity and approximately 6 mm in diameter were continuously cast at rates of between 15 and 25 mm/min by a heated mould process and their mechanical properties evaluated. It was found that rods cast at 15 and 20 mm/min consisted of a single crystal, while rods cast at a speed of 25 mm/min were multi-crystalline and showed a unidirectional structure. Although room temperature tensile ductility to fracture varied widely, it was found that with an appropriate crystal orientation, cast rods can exhibit elongation by as much as 215%.

Jan 1, 2006

By R. Roufail

"Energy consumption in stirred mills has been studied, in the last couple of decades, on a macro scale. Effective operation and meeting particle size required for downstream operations used to be the main objectives behind energy utilization of stirred mills. In this paper, three energy terms are defined to assist in understanding the breakage mechanism for various types of minerals versus mill operation. The types of minerals studied had diverse physical and mechanical properties that are summarized as specific gravity, hardness and crystal structure. The minerals utilized in this study were quartz and galena. The effect of quartz and galena mix has been addressed as well as Lead-Zinc ore sample from SAG mill discharge. The energy input to the mill is function of the agitator speed, therefore three agitator speeds were evaluated, 1000, 1500 and 2000 RPM, respectively. The energy terms studied are specific energy (kWhr/ton). Effective energy is the ratio between net energy and total energy consumed by the mill. Last type of energy is the specific breakage energy, which is the net energy consumed by the mill per one-micron breakage. Results showed that specific energy and specific breakage rate are functions of mineral type, while effective energy is only function of mill input power (agitator speed).INTRODUCTIONGrinding is the largest energy consuming component of a mineral processing operation and typically consumes about 50% of the total energy used at a mining operation (Botin, 2009). Over the last two decades, stirred mills have been extensively utilized in mineral processing operations due to increased mineralogical complexity of ore bodies. Stirred mills grind particles to less than 10 µm by applying a high power intensity. The technology has been the focus of several research studies to investigate mill energy and grinding mechanisms. Becker, et. al. (2001) studied the relationship between different types of energy including input energy, specific energy, volume/mass specific energies, to stress intensity and final product particle size. Other studies such as by Kwade (1999), Kwade and Schwedes (2002), Blecher et al (1996), Partyka and Yan (2007), Stender et al (2004), focused on mill design and/or stress intensity distribution. Peukert (2004) studied the effect of mechanical properties of the grinding media and ground material on the comminution process."

Jan 1, 2016

By Kyeong Woo Chung, Ho-Sung Yoon, Jyothi Rajesh Kumar, Chul-Joo Kim, Sung-Don Kim

The aim of the present study is to investigate the extraction, separation and recovery of the indivisible metals of dysprosium and neodymium from permanent magnets scrap leach liquor solutions with meaningful recovery. The present experimental development focused on dysprosium separation from neodymium and recovery by suitable mineral acids. Fundamental studies of the effect of time, pH and extractant concentration on the metal separation were conducted followed by proposal of a mechanism for extraction. Process development included generation of McCabe-Thiele diagrams and counter current extraction (CCE) studies. After loaded organic generation from the CCE process, this was followed by scrubbing studies as well final recovery of dysprosium.

Jan 1, 2014

By S. C. Robinson

"IntroductionALTHOUGH most uranium deposits of the Canadian Shield lie along its western and southern margins, those of the Lake Athabasca region extend easterly along the north shore of the lake and beyond to Charlebois lake. The western end of this belt of deposits, in the vicinity of Goldfields, is 80 miles from the Palaeozoic contact, and its eastern end, at Charlebois lake, is 240 miles from the nearest Palaeozoic rocks.Deposits in this belt may be grouped in four districts, which are, from west to east:(1) The Goldfields district, an area approximately 20 miles square, centred on Beaverlodge lake and extending eastward from St. Joseph's point to Moose channel.(2) A small area in the vicinity of Sucker bay, which is about l0 miles east of Fond du Lac.(3) An area including Middle lake to the northwest shore of Black lake at the Nisto mine.(4) A fairly large area extending northward from the eastern end of Black lake, through Charlebois lake to Spreckley lake.HistoryThe region has stimulated interest in mining circles since the reconnaissance survey of J. B. Tyrrell of the Geological Survey of Canada in l893, who reported concentrations of iron along the north shore of lake Athabasca. The deposits were staked and re-staked up to the early 'twenties' but are too lean to form ore."

Jan 1, 1952

By J. Zachwieja

As part of a general review on study of surfactant blinding agents to improve gold recovery during cyanide leaching of carbonaceous gold ores, processes of CIL and RIL leaching using surfactants were investigated. When refractory ores were treated by surfactants, CIL and RIL leaching processes yielded significant improvement on gold recovery. This paper will discuss and compare the laboratory results from two different leaching processes on preg-robbing ores, as well as, illustrate the difference of potential fouling of the blinding agents on activated carbon and resins.

Jan 1, 2015

By Chris Harris, Kamal Adham

The use of HCl acid is gaining momentum among hydrometallurgical processes. However, the issue of environmentally efficient and economically viable ways to regenerate HCl acid (from various metal chloride intermediate products) remains a technology and operational challenge. The authors provide a state-of-technology review based on Hatch’s years of testing, design and commissioning experience with high-temperature units (fluid bed and spray roasters), plus the recent efforts in the area of low-temperature HCl regeneration.

Jan 1, 2014

By J. Cueto, M. Torres, J. Fernandez, J. Nuñez, C. Salgado, G. Zarate

Anglo American has used the extractant M 5640 in all the Divisions, which is an aldoxime modified with TXIB formulation, except in Los Bronces, where an aldoxime modified with tridecanol (TDA) formulation is used. It is a well-known fact that the aldoxime degrades while the modifier does not. With time the aldoxime/modifier ratio decreases significantly depending on the operating conditions of each plant. In order to evaluate the effect of this increasing modifier content in the organic of the plant, especially in the organic losses, a complete metallurgical test work program was started at laboratory and pilot plant scale. Results showed that the addition of aldoxime without modifier does not affect the chemical performance of the organic phase, but there is a significant decrease in the viscosity and density of the organic phase. Based on the results obtained in the metallurgical program, it was decided to run plant scale tests at both SX plants, Mantos Blancos and Mantoverde. In these tests, instead of adding the usual formulation of aldoxime modified with TXIB to maintain the organic inventory, CuPRO MEX™ 3406 which is an aldoxime without modifier is going to be added until the original aldoxime/modifier ratio is reached. The plant tests started in April 2013 at Mantos Blancos and in June 2013 at Mantoverde and will last 18 months. The results obtained at the laboratory and pilot plant scale, together with the preliminary plant test results, are discussed in this paper.

Jan 1, 2014

By Erwin L. Zodrow

"This paper is based on a statistical analysis of the Smallwood iron ore mine (6). In this mine, the prediction of magnetite is especially difficult because of strong trends. Recognizing the statistical limitations of the sample data, the paper approaches the basic statistical analysis of the magnetite by endeavouring to obtain a first approximation of its sample density function. The knowledge of the distribution of a random variable is essential for several reasons, but particularly: (1) to obtain reliable estimators of the population parameters -for example, mean and variance; and (2) to use these estimators in hypothesis-testing concerning future experiments -sample points and sample intervals."

Jan 1, 1968

By D. R. Rice

"The Smoky Valley Common Operation is managed and 50 percent owned by Echo Bay Mine' s Round Mountain Gold Corporation. The other partners with 25 percent each are Homestake Mining Company and Case Pomeroy. The operation in central Nevada includes an open pit, 3-stage open-circuit crushing train and heap leaching on asphalt pads. Presently, about 18,000 tons per day of 0.039 troy ounce gold per ton are transferred to the leach pads, and a similar tonnage of leach residue is transferred to a waste dump. One million tons of ore are being leached at any one time.Gold and silver cyanide are adsorbed from pregnant leach solution on activated coconut shell carbon granules. Pressure stripping desorbs values from loaded carbon to electrowinning solution.Three electrowinning cells are operated in parallel. Each contains six cathodes. Each cathode includes about 40 troy ounces (2.7 pounds) of Number 2 medium coarse steel wool. The wetted area of each cathode is about 24 by 30 inches. Solution flow is 2 to 3 gallons per minute per electrowinning cell. Average current flow is 25 amperes per cathode. The voltage is controlled in the range of 3 to 4 volts to maintain desired amperage.Twice a week two cathodes are pulled from each cell and drained. Each cathode is split into four portions. These are put in a steel pan coated with WD-40 and dried overnight.Each dried cathode portion is put into a paper sack. Each group of four sacks corresponding to a cathode is weighed together. The typical weight ratio of loaded cathode wool to new cathodes is 9 or 10 to 1. To each sack is added 35 troy ounces of silica, 45 troy ounces of anhydrous borax, 35 troy ounces of nitre, and 5 troy ounces of fluorspar. The sacks are taped shut."

Jan 1, 1986