Search Documents

By A. S. H. Kabir, I-H. Jung, J. Su, S. Yue, M. Sanjari

The final mechanical properties of wrought magnesium alloys are mostly controlled by microstructure and crystallographic orientation or texture. In common magnesium alloys, grain coarsening occurs during annealing process and formation of undesirable basal texture cannot be changed markedly. The aim of this work is to investigate the effect of static precipitation on microstructure and texture evolution during annealing at 250 °C after warm rolling of Mg-Al-Sn alloy. Mg-3Al-3Sn (wt. %) alloy has been designed using thermodynamic modeling software, FactSageTM, based on forming target stable and incoherent Mg2Sn precipitate within the industrial deformation temperature range. Microstructures and precipitation were investigated by optical and scanning electron microscopes and macro-texture was measured by X-ray diffraction (XRD) techniques. It was found that static precipitates form in a large scale at the recrystallized grain boundaries and retards the grain growth during annealing. Slight weakening in basal texture was also observed during annealing.

Jan 1, 2014

By J. Oliveira, A. R. Barnes, R. Pandher

Sub-stoichiometric roasting of arsenic-bearing copper ores is a well established practice. However, ores containing calcium commonly prove challenging where very low arsenic levels are desired, but the reasons for this phenomenon have largely been speculative. In the course of treating arsenicbearing copper ores by partial roasting in fluid bed reactors, XPS encountered one of these Ca-bearing ores which proved a challenge to roast to acceptably low levels of arsenic. Mineralogical examination of the calcines using a combination of XRD (X-ray diffraction), QEMSCAN (Quantitative Evaluation of Materials by Scanning Electron Microscope) and EPMA (Electron Probe Micro-Analysis) helped to identify the arsenic bearing species and assisted in developing a workable theory on the sequence of reactions occurring during the roast. With the assistance of thermo-chemical modelling, this allowed adjustment of the roasting conditions to minimise the amount of arsenic retention in the calcine in spite of the presence of calcium in the ore and advance the roasting program to a commercially acceptable solution.

Jan 1, 2014

By R. L. Bruening, R. M. Izatt, N. E. Izatt, K. E. Krakowiak, S. R. Izatt

The need for selective metal separations has increased as the mining industry encounters more complex ore bodies and the demand for higher performance end products expands. Molecular Recognition Technology (MRT) is a green chemistry process that involves use of SuperLig® resins to selectively remove desired metals from a variety of solutions in mining and metals processing industries. Recoverable metal concentrations can range from multiple g/L to mg/L or less. The MRT separation process is based on green chemistry principles and can efficiently produce high purity metal products with minimal waste generation and energy usage. In this paper, applications of MRT to metal recovery and purification in the minor and specialty metals industry will be presented and discussed. Examples will be described involving cobalt, nickel, zinc, rhenium, iridium, indium, germanium, bismuth, and cadmium, as well as removal of lead and iron from process streams.

Jan 1, 2015

Vast quantities of cosmic material, ranging in size from fine dust to large meteorites and planetoids, have been colliding with and accumulating on the earth since its origin 4.5 billion years ago. There are less than twenty well preserved meteorite craters and Jess than thirty fossil craters or astroblemes on the present face of the earth. On the moon, there are approximately 200,000 craters on the visible face alone -the largest crater being 132 miles in diameter and attaining a depth of 16,000 feet. Making allowances for the different physical conditions on the moon and assuming that these lunar features are of impact origin, the indifference is that, since primeval time, large numbers of celestial objects have also encountered the earth, but that both the topographic expression of the impact and the objects themselves have been destroyed by weathering and erosion. It may be reasonable to suggest that additions of cos-mic bodies have materially altered the chemistry of the earth's crust from place to place and that the impact of large meteorites and asteroids has created zones of weak-ness in the crust that could be the center of magmatic intrusion and mineralization.

Jan 1, 1965

By A. Navarra, C. Arrancibia, R. Yañez, C. Acuña, F. Valenzuela

"Discrete event simulation (DES) is a suitable framework to evaluate and optimize the dynamics of sulphide smelters. In particular, iron-nickel-copper-cobalt sulphides undergo continual oxidation within a roasting or smelting operation, followed by batch oxidation within the converting operation, thus producing iron-free Bessemer matte (or blister copper, in the case of copper smelters); this semi-finished product undergoes further processing to produce nickel, copper and cobalt products, and to recover precious metals. The juncture between continuous smelting and batch converting is often an appropriate focus for the earliest phases of DES development, since it is typically a major bottleneck within nickel and copper smelters; later phases may include increasing levels of detail for auxiliary unit operations, as well as plant logistics. Moreover, DES can support matte-slag chemistry, including Gibbs free energy balances to determine the iron speciation within the slag. DES is therefore capable of linking the fundamentals of oxidation reactions to the intricacies of plant dynamics.INTRODUCTION Discrete event simulation (DES) is gaining acceptance within the extractive metallurgy community, as a technique that quantifies the system-wide performance of metallurgical plants under conditions of uncertainty (Wheeler & McGinty, 2015). In particular, over 90% of smelters that process nickel-copper-cobalt sulphides and copper sulphides exhibit similar semi-continuous dynamics (Crundwell et al., 2011b; Schlesinger et al., 2011b), in which the converting aisle produces batches of material that are sent for further processing (Figure 1). Thus the tools and practices that are developed for a specific sulphide smelter are often relevant to numerous other smelters.The juncture between continuous smelting and batch converting has long been a focus for discrete event simulation (Welgama et al., 1996). Nonetheless, the broad acceptance of DES in nonferrous smelters has been hindered by interdisciplinary barriers that divide industrial and metallurgical engineers (Navarra et al., 2016; Noorossana et al., 2012); this divide has been less severe in steel plants (Hollocks, 2006). In recent years, DES has been used in copper smelters to analyze crane-and-ladle motions (Coursol et al., 2009a), reverts production and consumption (Noorossana et al., 2012), and innovative control systems (Herrera et al., 2016); additionally, DES models have accounted for shutdowns and random breakdowns to provide realistic assessments of copper smelter capacities, thus guiding equipment upgrades (Campbell et al., 2013; Coursol et al., 2009a). All of these studies feature a Peirce-Smith converting aisle similar to Figure 1 that, under normal operations, constrain the smelter throughput, and are thus a bottleneck (Campbell et al., 2013; Navarra et al., 2016)."

Jan 1, 2017

By Ray Collier

MINING TODAY l EXTENSIVE AND EXPENSIVE PERMITTING PROCESSES WITH UNKNOWN RESULTS l GENERAL AND IMPASSIONED RESISTANCE TO RESOURCE BASED INDUSTRY l SOPHISTICATED, ORGANISED, AND WELL FUNDED OPPOSITION l MOST LOCAL GOVERNMENT DOESN?T WANT MINING TODAY?S TALK l FOUR SPECIFIC OPERATIONS ON WHICH OUR EXPERIENCE IS BASED ? SECHELT ? CADMAN ? GRANVILLE ISLAND ? LEHIGH CEMENT DELTA PLANT l OUR APPROACH TO COMMUNITY RELATIONS

May 1, 2002

By D. S. Evans

Major Project Blues Over the last two decades, almost every major project has suffered significant cost overruns, significant schedule delays, and/or poor quality work. Exceptions are rare and most projects that tout being ?On Time and Under Budget? have re-cast schedules, significantly modified scope or revised base estimates. The problem isn?t new. In the late 1980?s the Rand Corporation published a study showing that 80% of all major projects had significant cost and schedule overruns. The problem is not restricted to the Canadian environment, or to a specific industry. It is a global problem.

May 1, 2013

By R. Llewellyn

"Wear damage is responsible for very high maintenance costs and significant production losses in the oil sands industry of northern Alberta.It affects all areas of operations and involves a panoply of wear mechanisms from low stress sliding abrasion at extremely frigid temperatures during winter mining, to elevated temperature erosion/corrosion in processes where bitumen is converted to lighter hydrocarbon products.There is no universal panacea to defend against such diverse attack and a wide selection of resistant materials and systems is employed. These range from relatively soft rubbers which rely on their elastic properties for their protective capability, to some of the hardest ceramics and cermets which are currently available commercially.Details are presented of the characteristics and forms of the variety of wear materials being used and how they relate to the requirements of their areas of application. The review focuses on the practices followed at Syncrude Canada Ltd., which is the larger of the two commercial oil sands plants."

Jan 1, 1997

By O. S. Perry, G. H. Charlewood, K. Griffin, S Ogryzlo, H. Hopkins, G. MacIntosh

"The gold mines of Kirkland Lake are in Teck township, Timiskaming district, Ontario, latitude 48°9'N. and longitude 80°3'W., at an elevation of 1,038 feet above sea-level.There are seven contiguous producing mines in a length of 3;1/2 miles along the general east-west strike of the deposits. The seven mines are, in order from west to east, Macassa, Kirkland Lake, Teck-Hughes, Lake Shore, Wright-Hargreaves, Sylvanite, and Toburn.The first discovery of gold in the zone was made by W. H. Wright in 1911 on the east claim of the Wright-Hargreaves property, and the following year the Tough brothers and H. Oakes found gold in what is now the No. 1 vein_ at the Toburn. Production began at the Toburn in 1915, followed by Teck-Hughes in 1917, Lake Shore in 1918, Kirkland Lake Gold in 1919, Wright-Hargreaves in 1921, Sylvanite in 1927, and Macassa in 1933.To the end of 1946, 31,938,350 tons of ore had been milled at the Kirkland Lake mines, from which 16,132,700 oz. gold, having a value of $498,517,600, were recovered. The bullion varies from mine to mine between 800 and 900 fine, the average for all the mines being 853. The average fineness of the native gold is 941.The workings of some of the mines are more than 6,000 feet deep and sinking to depths below 7,000 feet is now in progress.GENERAL GEOLOGYThe regional structural geology of the area in which the mines of Kirkland Lake occur is described in a preceding paper in this volume by J. E. Thomson."

Jan 1, 1954

By N. Bakhshizadeh

In this investigation, the aging effect on creep behavior of A12024-10%SiC composite fabricated by powder metallurgy was studied. P/M bars were manufactured by hot powder extrusion method at 450°C with a ratio of 16 to 1. Creep specimens were over-aged at 187 ºC for 43 h. It was found that almost full density composite with relatively homogenous distribution of reinforcing particles throughout the aluminum alloy matrix could be attained by direct powder extrusion process. Creep tests were conducted at temperatures from 275 to 325°C under stresses from 25 to 60 MPa. The analysis of the creep mechanism determined that dislocation glide was the predominant mechanism of plastic deformation. The activation energy of the creep process was found to be higher than that of lattice self-diffusion in pure aluminum.

Jan 1, 2007

By Barbara A. Filas

The IFC goal is to promote private sector investment in developing countries which will reduce poverty and improve people?s lives. The developing country goal is to promote health, education and employment opportunities that improve their economies and their standard of living. The mining company goal is to Promote successful ?triple bottom line? mining projects that will grow shareholder equity

May 1, 2002

By Sandeep Singh Sandhu, Karanvir Singh Ghuman, Manjit Singh

"Cobalt based super alloy stellite 6 was weld cladded on AISI 304 L stainless steel using SMAW process in order to improve the wear resistance for tyre crusher blades. Microstructure characterization and micro hardness testing was performed on stellite 6 cladding. The suitable parameters viz. 80 Amp current with arc weaving technique was selected by performing bead on plate experiment were further used for depositing multipass multilayer cladding to achieve full filler chemistry at the top surface. Further GTAW process was used for re-melting the top surface of the cladding. Comparative evaluation of the claddings showed that TIG re-melting resulted in increased microhardness and wear resistance in comparison to as cladded specimens even with lesser deposition of material. It was observed that TIG re-melting improved the hardness from 603 HV0.5 kg to 712 HV0.5 kg. Micro structures of stellite 6 contained cobalt solid solution matrix along with inter dendrite chromium carbides which resulted in the increased micro hardness values. Pin on disc abrasion tests were carried out at room temperature and the worn out surfaces were characterized using SEM and EDS.INTRODUCTIONThe crusher blades are used in many industries for crushing various types of material and its wider applications in tyre rubber crushing mills, metal-powder crushers industries etc. Most of the crusher blades are damaged by the wear and impact loading conditions. It is because of metal to metal abrasion and the temperature also plays a vital role in blunting the cutting edges of these blades. The wear is the major cause which leads to loss of material and thus the productivity that can never be recovered (Kotechi et al., 1992). The wear can be reduced by coating of various super alloys which could reduce the behavior of metal degradation even in aggressive environments. Cladding of cheaper low alloyed material with expensive superalloys to enhance the performance of components at low cost has been investigated by many scholars (Deng et al., 2010, Kennametal, 2007, Lolla et al., 2014, Singhet al., 2014, J.N et al., 2003, Ramkumar et al., 2012). Many researchers have reported that cladding is an application of build-up deposits of specialized alloys to resist abrasion, high temperature corrosion and impact loadings. Cladding is used for providing required mechanical strength properties as well as inhibition of oxidation and other corrosive degradation. Coatings are used to protect the heat affected areas like tubes of fluidized bed combustor etc. (Kirchbner et al., 2008, Wang et al., 1994, Hocking et al., 1993, Ananthapadmanabhan et al., 1991, Staia et al., 2001). Coating techniques are widely used for the protection of turbine engine and boiler tubes against high temperature corrosion attack, power generation equipment, chemical process equipment, aircraft engines, pulp and paper processing equipment, bridges, rollers and concrete reinforcements, orthopedics and dental, land-based and marine turbines, ships. Coatings of stellite 6 are widely used in steam turbine blades and boiler tubes for power generation because of an excellent combination of impact, wear and other properties. It can maintain its properties even at high temperature and in harsh environments (Kobayashiet al., 1999, Alam et al., 2009, Munehru et al., 2009). The loading and unloading conditions experienced by the material may induce the surface cracks which lead to its breakage and leaving large pits in the surface (Meng et al., 1995). Many researchers have reported that the properties of cladded layers can be increased by various techniques such as controlling the current variations, dilution, heat input, laser and other re-melting processes, addition of special alloying elements, speed of weldingetc(C.M Anaet al., 2002, Kumaret al., 1999, Luo et al., 2012, et al., Madadi et al., 2011, Shin et al., 2003, Kuzucu et al., 1997, Sudha et al., 2008, Sawant et al., 2017, Houdkova et al., 2016, Ciubo"

Jan 1, 2017

By ByongPil Lee, Changkyu Lee, Jin Gyun Park, Hyung Sub Eom, Sung-Koo Jo, Jae-Young Lee, Gilsoo Han

"A new hydrometallurgical process for nickel extraction from a low grade laterite ore such as limonite has been developed by RIST and POSCO. This POSCO Nickel Extraction Process (PosNEP) consists of five main processes: ore reduction using hydrogen as a reductant; acid leaching at atmospheric pressure and temperature; cementation by the use of reduced-ore seed; production of the main product such as ferronickel or a high purity nickel compound; and production of by-products such as cobalt and iron in the forms of cobalt sulfate and iron oxide. In addition, hydrogen produced in acid leaching and hydrochloric acid regenerated in pyrohydrolysis for iron oxide production can be reused in the process, which makes PosNEP more cost-effective. The performance of PosNEP has been proven through pilot tests, showing that this process is economically and technically viable. In this paper, basic concepts and detailed test results of PosNEP are shown.INTRODUCTIONNickel has been extracted from two types of ore, sulfide and oxide ore. Nickel and cobalt usually occur together in the ores. The principal ore mineral of the sulfide is pentlandite, (Ni,Fe)9S8, which is easily beneficiated to produce sulfide concentrates(Moats & Davenport, 2014). These concentrates are usually treated by smelting and converting to make a matte. The produced matte is then purified through either hydrometallurgical or pyrometallurgical processes to produce high-purity nickel. In general, this process for sulfide ore has been known as a more cost-effective process than that for oxide ore.The oxide ore is laterite comprised of two different ore types, saprolite and limonite. The main nickel-bearing mineral of saprolite is nickeliferrous garnierite,(Mg,Ni)6Si4O10(OH)8, and that of limonite is nickeliferrous goethite (Fe,Ni)O·OH ore (Moats & Davenport, 2014). Since the saprolite has high contents of nickel and slag formers (MgO and SiO2) and a low content of iron, it tends to be treated by a pyrometallurgical smelting process such as calcination and electric furnace techniques to produce ferronickel for use in stainless steel. In this process, the cobalt in the ferronickel does not have any economic value."

Jan 1, 2017

By D. R. Reeves

This paper describes the geophysical Jogging of coal that is being carried out for the National Coal Board in the United Kingdom. An explanation of the technique is given and results are presented showing estimations of seam thickness to within ±0.5 in. and ash content to accuracies of ±2.5 per cent. The basic method of interpretation is outlined and some conclusions regarding the conditions of roof and floor material which may be deduced from the logs are explained. An indication of future developments in this field, including the identification of coal type and moisture content, is given.

Jan 1, 1971

By J. H. Walsh

IN THE DEVELOPMENT of procedures for the separation of minerals, the choice of reagents for flotation is frequently determined by the extent to which a given mineral is wettable by water. Measurements of the contact angle of an air bubble on wet mineral surfaces are often used in the laboratory to estimate the wettability of the surface. For the results of these measurements to be reproducible, the surface of the mineral must be polished to a mirror-like smoothness and must be free from oily contamination. Elaborate procedures for preparing mineral surfaces have been developed by Wark ( 1) and Taggart (2), and these procedures have been generally accepted as adequate for their purpose. The polishing techniques, how-ever, have certain inherent disadvantages which make it impossible to assess the effects of polishing, entrained abrasive, and adsorbed gases on the wettability of the mineral surface.

Jan 1, 1957

By C. H. Madsen

THE Hard Rock gold mine is in the Little Long Lac mining area, Thunder Bay district, northwestern Ontario. It is four miles by road from the town of Geraldton, which is on the Canadian National railway, 180 miles northeast of Port Arthur. The original discovery of gold-bearing quartz veins on the property was made in 1931. Shaft sinking began in the fall of 1934 and approximately 7,400 feet of lateral development on four levels was completed. In 1935, further discoveries were made half a mile west of the early workings, and the No. 2 shaft was sunk in this area in a porphyry zone. In January, 1938, a 20C-ton cyanide plant was completed and began drilling ore from the gold-bearing porphyry orebody. The daily feed was increased gradually to 300 tons in the next six months and a recovery of 97.5 per cent was effected. During the summer of the same year, a new and larger orebody was discovered to the north of the porphyry zone. It occurs in a band of iron formation and contains a high percentage of pyrite and arsenopyrite. Extensive tests were rr.ace on this sulphide ore in the Mines Branch ore dressing laboratory at Ottawa, in the laboratory of Canadian Industries, limited, at Toronto, and later at the mine, to find a suitable method of treatrr.ent. As a result of this research, a Potation plant was added to the original cyanide mill and on November 7th, 1938, differential flotation was used to separate the pyrite from the arsenopyrite fraction of the ore. The pyrite concentrate was re-ground and cyanide:l, and the arsenopyrire concentrate was stored for subsequent treatment. Differential flotation was discontinued in April, 1939, in favour of bulk formation of all the sulphides, and the whole cyanide residue was stored. On March 15th, 1939, a 10-ton pilot roaster was completed and rests were conducted on the arsenopyrite concentrate and the bulk concentrate. The results obtained led to the building of two roasters of the same type, large enough to roast all the concentrates. These roasters were put in operation on September 24th, 1939, and the calcines were cyanided in the original circuit.

Jan 1, 1941

By C. Allen

In 2004, Boliden Odda underwent an extensive modernisation project targeting mainly the leaching section of the plant. Direct leach technology was introduced as part of this project. The Direct Leach process, developed by Outokumpu, is an atmospheric oxidative leach of zinc sulphide concentrate. The effects of this new processing operation on behaviour of iron in the plant are discussed. As well, the filterability of the new residue on belt filters prior to its deposition in mountain caverns is also discussed. The solids from the direct leach process have been analysed by scanning electron microscopy, and the results of these analyses are presented.

Jan 1, 2006

By L. Narhi, K. Haavanlammi

"Approximately two thirds of annual nickel production is used as a raw material in the making of stainless steel, and about 60% of these nickel products are in the form of metallic nickel such as nickel cathode or briquettes. In the stainless-steel production process nickel is blended with iron and chrome-based raw materials, and metallic nickel is typically only required for final steel fine-tuning. Outotec offers a new FeCrNi technology to enhance the nickel value chain for stainless steel producers. This involves the use of an HPAL-based intermediate nickel product (e.g., mixed hydroxides or NiO) as raw material in the Outotec FeCrNi process, for the production of a FeCrNi Master Alloy. The new process, designated as the FeCrNi process, offers multiple benefits compared to existing technologies such as: higher tolerance for impurities in the HPAL intermediate product, avoiding the need for further nickel refining, and the improved recovery of all metals in the FeCr process. The complete new FeCrNi value chain is based on proven technologies such as HPAL and the Outotec FeCr-process. This new innovative and promising value chain offers improved efficiencies for the HPAL based nickel production process combined with excellent sustainability aspects.INTRODUCTION In today’s global economy there is a constant need to improve the efficiency and sustainability of the metals production. The requirements for modern metal refining are tightening and cost efficient, safe and sustainable operation is the precondition for all investment. Outotec is offering now a novel way to combine FeCr and Nickel production to create a completely new value chain to source nickel to stainless steel. BACKGROUND Nickel The current nickel mine production is in the level of 2,000 tons annually and it is split 44% from sulphide based deposits and 56% from laterite deposits (Figure 1). Most (40%) of the nickel is refined to pure nickel metal whereas other products are FeNi (19%) and Nickel Pig Iron NPI (20%) (Roskill). The remaining part, roughly 21%, is nickel chemicals and intermediates. Most of the new investments in nickel are in the direct shipping of laterite to produce nickel pig iron. HPAL process is considered in few projects but no major HPAL projects have been started since the Ambatovy plant in Madagascar. Ambatovy reached the commercial production in 2014. The main primary nickel used is stainless steel manufacturing. In the year 2016 about 68% (~1,360 kt) of primary nickel production was used in stainless steel."

Jan 1, 2017

By A. M. A. Mohamed, F. H. Samuel, S. Alkahtani

"This article was undertaken to investigate the effect of nickel and zirconium additions on the strength of 354 aluminum cast alloy. The cast alloys were given a solutionizing treatment followed by artificial aging at 190 ºC for 2 hr. High temperature tensile tests were conducted at various temperatures from 25ºC to 300ºC. Optical microscopy and scanning electron microscopy were used to study the microstructure of the samples. The results revealed that the intermetallics phases of (Al,Si)3(Zr,Ti), Al3CuNi and Al9NiFe are the main feature in the microstructures of alloys with Zr and Ni additions. The results also indicated that the tensile strength of alloy decreases with an increase in temperature. The combined addition of 0.2 wt% Zr and 0.2 wt% Ni leads to a 30% increase in the tensile properties at 300ºC compared to the base alloy.INTRODUCTIONThe task of improving the mechanical properties in an aluminum alloy at high temperatures should include the knowledge of several factors which are related principally to a decrease in the strength of the metal with increasing temperatures. This behavior is linked to the change or deterioration in the principal metallurgical parameters of the specific cast aluminum alloy during its performance at higher temperatures. Most of applications of Al-Si casting alloys are generally used at temperatures of no more than 230°C (Lee & Chen, 2002). This recommendation is made in view of the fact that, for certain applications such as those required by the automotive industry, these alloys must operate over a wide range of temperatures and stress conditions where temperatures are liable to rise even higher than 230ºC (Robson & Pragnell, 2003).Aluminum-silicon-copper-magnesium alloys such as the 354 alloys show a greater response to heat treatment as a result of the presence of both Mg and Cu. These alloy types display excellent strength and hardness VALUES (although at some sacrifice of ductility and corrosion resistance. These alloys are used for a wide range of applications, such as engine cooling fans, crankcases, high speed rotating parts, structural aerospace components, air compressor pistons, fuel pumps, compressor cases, timing gears, rocker arms, machine parts, and so forth (Cáceres, Svensson, & Taylor, 2003; Rurrxia, Rong-de, Yu-hua, Cherrxi, Xiao-feng, Heng-rong, & H. Zhuang-qi, 2004)."

Jan 1, 2012

By G. Banini

Prior to installation of High Pressure Grinding Rolls (HPGR) at PT Freeport Indonesia (PT-FI) a series of laboratory tests were carried out to determine the design parameters and also determine key performance indicators (KPIs) for the industrial unit. The design parameters derived from the lab test work were then scaled up to estimate the industrial capacity of the HPGRs to be installed. These parameters include specific power draw, specific throughput, and specific force, rolls speed, product size distribution and wear rate of the rolls. This paper compares the performance of the scale-up procedure against the installed industrial size HPGR. Overall, the specific throughput of the industrial size HPGR is higher by a minimum of 30% compared to the expected scale-up value. As a result of the high specific throughput, the specific power draw and grind sizes are below the scale-up expectations in the commercial application. The impact of these factors also contribute to a lower than expected wear rate on the industrial rolls. Installed rolls achieved a service life in excess of 18,500 hours relative to the target of 6,850 hours predicted from the laboratory testing.

Jan 1, 2012