Search Documents

By Arsenio Enriquez, Adrian Deneys, Ryan Walton, Jenny Esker

NOx emissions at the Rio-Tinto Kennecott Copper (RTKC) smelter, near Salt Lake City, Utah, are regulated to a compliance emission limit at the Main Stack of 15.9 kg/hr on an annual rolling average. The paper discusses RTKC efforts and improvements, particularly related to the anode furnace operations, since the Smelter modernization in 1995 to comply with the air quality approval limit. This includes replacement of gaseous ammonia to Steam-Gas Refining (SGR) system during the copper reduction stage, upgrade anode furnace oxygen-fuel burner from Praxair’s Stabilized Jet (S-J) to Jet Lance (J-L) technology, development and implementation of operational best practices and continuing to investigate and evaluate NOx control technology and strategy in the industry. In early 2016, changes to Praxair J-L Burner technology on both anode furnaces, utilizing wider lance spacing, was adopted and further improved NOx emission levels well below the compliance limit. INTRODUCTION Since the establishment of the Clear Air Act in 1970, the Environmental Protection Agency (EPA) has been regulating emissions of nitrogen oxides (NOx) to reduce impact on public health and the environment (USEPA, CAA, USEPA, NAAQS). As a requirement of the Clean Air Act, the EPA evaluates the standards for NOx and criteria pollutants on a periodic basis and as a result, standards have been revised and ultimately reduced over time (USEPA, CAA, USEPA, NAAQS, UDAQ, SIP). To remain competitive with changing regulations and in conjunction with Rio Tinto environmental standards for continuous improvement, the RTKC smelter has been motivated to research and implement NOx control strategies. NOx health and environment impacts NOx refers to a group of seven compounds including the most common, nitrogen dioxide (NO2). (USEPA, NO2). The EPA enforces both short-term (1-hr average) and long-term (annual average) standards for NO2 to protect against associated respiratory system impacts. Short-term exposure of elevated NO2 concentrations can aggravate respiratory diseases and lead to symptoms such as coughing, wheezing or difficulty breathing while longer exposures may contribute to the development of asthma and potentially increase susceptibility to respiratory infections. (USEPA, NO2) Additionally, NOx is necessary in the formation of ozone and particulate matter less than 2.5 microns (PM2.5). Ozone concentrations can negatively impact lung function and in some cases, contribute to chronic obstructive pulmonary disease. (USEPA, Ozone) The particles associated with PM2.5 can reduce lung capacity and aggravate heart conditions. (USEPA, PM2.5) For all NOx related pollutants, children and the elderly are generally at greater risk for the health effects. (USEPA, NO2, USEPA, Ozone, USEPA, PM2.5)

Jan 1, 2019

By E. V. Konopleva, H. J. McQueen

Steels in high variety have been providing strength and ductility for more than a century mainly through complex heat treatments following hot shaping. The economical and sustainable goal was a steel with the two operations combined through applying knowledge of dislocations and strengthening mechanisms aided by new mechanical and microstructural techniques. Primary hot reversing-mill rolling produced static recrystallization (SRX) between every pass to significantly finer grain size. Hot torsion showed that with lay-on temperature and rate of reduction suited to gradual precipitation of minor additions of Nb, the austenite grains would become highly pancaked; the existence of very fine subgrains along the grain boundaries (GB) could be deduced from tests on stainless austenite. The HSLA strip had to be water-jet cooled immediately to prevent SRX at austenite GB and ensuring complete transformation to ferrite avoiding grain growth after coiling. Confirmation on old mills and successful product led to the design of more flexible mills for wider range of compositions and products. A significant one was auto bumpers that reduced crash damage. More crack-resisting compositions were developed for strip welding into line pipe for arctic oil transport. Lower metal consumption and easier fabrication has resulted in more sustainable welded bridging.

Jan 1, 2015

By Catharine E. G. Farrow, David H. Watkinson

The Ni-rich Epidote Zone of the Fraser Mine at Sudbury is characterized by alteration assemblages rich in epidote, actinolite and magnetite which are roughly concentrically zoned and up to hundreds of meters in length. These zones form discrete areas within the igneous Footwall Breccia below the Sudbury Igneous Complex. The assemblages grade from epidotized Footwall Breccia matrix,through actinolite-bearing rocks with few vestiges of original Footwall Breccia textures, into the most intensely altered rock, a magnetite-rich facies. Pentlandite, pyrrhotite and pyrite are the dominant sulfdeminerals; chalcopyrite is minor. The strongest geochemical differences compared to original Footwall Breccia occur where epidote and actinolite dominate the alteration assemblage (EPDZact facies). The most intense alteration facies are typifed by low Cu/(Cu+Ni) values of <0.1. Strong positive correlations exist between Ni and Co, Cu and Au, and among Ir, Os, Ru and Rh. Chondrite-normalized Ni - PGE -Au - Cu plots display an overall increase in all elements from the least to the most intensely altered facies except for Au and Cu. As the proportion of actinolite increases in the EPDZact facies, the chondrite-normalized profles fatten considerably due to low Au and Cu contents. Abundances of Ni, Ir, Ru and Rhalmost ubiquitously increase with degree of alteration. In contrast, Cu, Zn, Ag and Au contents are low in almost all facies. It is suggested that saline hydrothermal fluids moved through the Epidote Zone formation and became more oxidized as they reacted with the Footwall Breccia and with footwall units, including ultramafic rocks. As this trend continued, magnetite-rich zones eventually developed. The occurrence of calcite locally in these magnetite-rich zones suggests that the pH of the fluid increased, causing Cu solubility to drop as activity in the hydrothermal system waned. Sudden changes in fluid composition such as this may have been due to an influx of fluid from bounding ultramafic rocks. Hydrothermal activity was focused along the margins of footwall ultramafic units. Individual hydrother-mal cells may have formed in the Footwall Breccia along pre-existing structures or sulfde concentrations. Metals may have been scavenged from sulfide-bearing Footwall Breccia and possibly Sublayer rocks. Nickel and some PGE were deposited in the Epidote Zone, whereas Cu, Au and Ag continued out-ward into the footwall where they were deposited as Cu-rich footwall veins. Copyright © 1996 Canadian Institute of Mining, Metallurgy and Petroleum.

Jan 1, 1996

By Catharine E. G. Farrow, David H. Watkinson

Abstract-The Ni-rich Epidote Zone of the Fraser Mine at Sudbury is characterized by alteration assemblages rich in epidote, actinolite and magnetite which are roughly concentrically zoned and up to hundreds of meters in length. These zones form discrete areas within the igneous Footwall Breccia below the Sudbury Igneous Complex. The assemblages grade from epidotized Footwall Breccia matrix, through actinolite-bearing rocks with few vestiges of original Footwall Breccia textures, into the most intensely altered rock, a magnetite-rich facies. Pentlandite, pyrrhotite and pyrite are the dominant sulfide minerals; chalcopyrite is minor. The strongest geochemical differences compared to original Footwall Breccia occur where epidote and actinolite dominate the alteration assemblage (EPDZact facies). The most intense alteration facies are typified by low Cu/(Cu+Ni) values of <0.1. Strong positive correlations exist between Ni and Co, Cu and Au, and among Ir, Os, Ru and Rh. Chondrite-normalized Ni - PGE - Au - Cu plots display an overall increase in all elements from the least to the most intensely altered facies except for Au and Cu. As the proportion of actinolite increases in the EPDZact facies, the chondrite-normalized profiles flatten considerably due to low Au and Cu contents. Abundances of Ni, Ir, Ru and Rh almost ubiquitously increase with degree of alteration. In contrast, Cu, Zn, Ag and Au contents are low in almost all facies. It is suggested that saline hydrothermal fluids moved through the Epidote Zone formation and became more oxidized as they reacted with the Footwall Breccia and with footwall units, including ultramafic rocks. As this trend continued, magnetite-rich zones eventually developed. The occurrence of calcite locally in these magnetite-rich zones suggests that the pH of the fluid increased, causing Cu solubility to drop as activity in the hydrothermal system waned. Sudden changes in fluid composition such as this may have been due to an influx of fluid from bounding ultramafic rocks. Hydrothermal activity was focused along the margins of footwall ultramafic units. Individual hydrothermal cells may have formed in the Footwall Breccia along pre-existing structures or sulfide concentrations. Metals may have been scavenged from sulfide-bearing Footwall Breccia and possibly Sublayer rocks. Nickel and some PGE were deposited in the Epidote Zone, whereas Cu, Au and Ag continued outward into the footwall where they were deposited as Cu-rich footwall veins.

Jan 1, 1996

By Arthur L. de Carle

"IntroductionThe Key Lake uranium-nickel deposits are located within a Mineral Lease centred at latitude 57 ° 12' north and longitude 105 °39' west along the southeastern rim of the Athabasca sedimentary basin in northern Saskatchewan, approximately 240 km north of La Ronge (Fig. 1). Access is provided by an allweather provincial highway from Pinchousc, situated about 200 km to the south, and a private airstrip maintained at the mincsitc.These deposits have been developed by Key Lake Mining Corporation on behalf of the Saskatchewan Uranium Joint Venture. Participants in the joint venture include Saskatchewan Mining Development Corporation (50%), Urancrz Exploration and Mining Limited (33 1/3 %) and Eldor Resources Limited (16 2/3 %).Considerable geological work has been conducted on the Key Lake orebodies and reported in summary papers published by Dahlkamp and Thn, (1977), Dahlkamp, (1978), Gatzweiler eta/., (1979) and Kirchner el a/. , (1980). However, intensive geological research is ongoing, particularly since many problems regarding ore genesis and controls remain unresolved . Exploration History and DevelopmentThe events (Gatzweiler eta/., 1980) which led to the discovery of the Key Lake ore bodies began in the summer of 1971 by following up on the reports of airborne radiometric anomalies and anomalous radon values in the Zimmer Lake water situated approximately 5 km to 6 km to the southwest. This work succeeded in locating a few high-grade uranium and nickel-bearing boulders associated with esker material. An integrated program, consisting of various geochemical and geophysical surveys along with diamond drilling, culminated in the discovery of the Gaertner orebody during July 1975. Subsequent fence drilling across the strike extensions of this ore structure located the Deilmann deposit, approximately I km to the northeast, in June 1976"

Jan 1, 1986

By M. R. Coffin

Since the plant startup in 1972, the leaching and jarosite precipitation circuits at the zinc plant of the Kidd Metallurgical Division have been reconfigured several times to improve overall performance, and/or to respond to market conditions. For the most part, the circuit changes have been driven by two market factors: the price of zinc and the price of silver. Until recently, circuit modifications undertaken to improve zinc extraction and recovery came at the expense of silver recovery, and vice versa. In 2004, the plant was modified once again to produce a precious metals-bearing residue, but additional leaching circuits were added to ensure that zinc extraction and recovery did not suffer as a consequence. The development of the zinc plant of the Kidd Metallurgical Division is updated in this paper, with a focus on the recent circuit modifications and associated control strategies that were implemented to maximize zinc and precious metals recoveries, and control the quality of the jarosite residue.

Jan 1, 2006

By André Chagnon, Michel Malo, Benoît Dubé, Chantal Pelchat

"Abstract- In the southern Gaspé Appalachians, gold mineralization is spatially associated with the Acadian dextral strike-slip Grand Pabos-Restigouche fault system. Two different structurally-controlled gold prospects, the Lac Arsenault and the Saint-André-de-Ristigouche, are described to unravel the genesis of gold mineralization in this part of the Canadian Appalachians.At the Lac Arsenault gold prospect, gold mineralization consists of Au-As-Pb-Zn-Cu-(Ag) polymetallic fault-filled quartz veins with laminated textures emplaced in brittle-ductile sinistral X shear fractures. Mineralized veins are hosted by Middle Ordovician graywacke of the Arsenault Formation, belonging to the Dunnage Zone, the Early Paleozoic oceanic domain of the Appalachians. Terrigeneous rocks of the Arsenault are regionally metamorphosed at the lower greenshist facies and the mineralized veins are included in a zone of Fe-carbonate alteration.The Sb-Au-As mineralization of the Saint-André-de-Ristigouche gold prospect, in the southwestern Gaspé area, comprises extension veins in the extension direction emplaced in brittle conditions. Mineralized veins are hosted by calcilutite and laminated silty and argillaceous limestone of the Early Silurian part of the White Head Formation, which belongs to the Gaspé Belt, the Middle Paleozoic successor basin in the Gaspé Appalachians. Metamorphic grade of the White Head Formation in the southwestern Gaspé area is very low, but the gold mineralization is included in a zone of hydrothermal propylitic alteration which includes two Cu-skarn mineral occurrences. The Lac Arsenault gold prospect has many characteristics of "greenstone-hosted quartz-carbonate vein" deposits whereas the southwestern Gaspé area, which includes the Saint-André-de- Ristigouche gold prospect, shows affinities with the geological setting of sediment-hosted gold deposits (Carlin-like deposits). The two gold prospects are controlled by the Grand Pabos- Restigouche fault system but they were not emplaced at the same level in the crust. Acadian strikeslip fauting played a major role in their respective genesis in providing channelways for ore-bearing fluids. The recognition of the analogy of the geological setting of the southwestern Gaspé area with that of Carlin-like mineralization gives new ideas for exploration in the area and elsewhere in the Appalachians.Résumé - Dans le sud des Appalaches de la Gaspésie, on trouve des minéralisations aurifères spatialement associées au système de failles de coulissage dextre acadien de Grand Pabos-Restigouche. Deux indices très différents, Lac Arsenault et Saint-André-de-Ristigouche, sont décrits pour évaluer la genèse des minéralisations aurifères à contrôle structural de cette partie des Appalaches canadiennes. Au Lac Arsenault, la minéralisation aurifère comprend des veines polymétalliques à Au-As-Pb- Zn-Cu-(Ag) en remplissage de failles. Ces veines à texture laminaire se retrouvent dans des zones de cisaillement fragiles-ductiles senestres de type X. Les veines minéralisées sont encaissées dans les grauwackes d’âge Ordovicien moyen de la Formation d’Arsenault appartenant à la zone de Dunnage, le domaine océanique du Paléozoïque précoce des Appalaches canadiennes. Les roches terrigènes de l’Arsenault sont métamorphisées régionalement au faciès inférieur des schistes verts et les veines aurifères sont dans de larges zones d’altération dolomitique (Fe-carbonate).Dans le sud-ouest de la Gaspésie, la minéralisation à Sb-Au-As de Saint-André-de-Ristigouche est dans des veines d’extension comprises dans la direction d’extension et mises en place dans des conditions de déformation fragile. Les veines minéralisées sont encaissées dans les calcaires argileux et les calcilutites de la partie silurienne de la Formation de White Head qui appartient à la ceinture de Gaspé, le bassin successeur du Paléozoïque moyen des Appalaches de la Gaspésie. Le degré métamorphique des roches du White Head est très bas, mais"

Jan 1, 1998

By Keith Donovan

Why are we here? Improve equipment performance & health ? Eliminate undesirable downtime and expensive secondary damage ? Maximize equipment life, optimize running costs (reduce costs) ? Improve safety and environmental performance ? Capture and consistently apply equipment knowledge ? Improve Proactive Maintenance processes & practices

May 1, 2009

By M. Hames, K. Larmour-Ship, B. Grinbaum, E. Buchalter, R. Hackl, B. Wassink

Sodium cyanide continues to be the lixiviant of choice for gold dissolution. Many gold ore-bodies contain a significant amount of cyanide-soluble copper which increases the cost of processing due to high cyanide consumption and high cyanide destruction and disposal costs. Several cyanide destruction processes are in use today, however, there are just a few cyanide recovery plants operating. A solvent extraction process to recover cyanide has been developed which utilizes the organophosphorous extractants Cyanex 923, di-butyl-butyl-phosphonate (DBBP) or tri-n-butyl phosphate (TBP) in Bateman Pulsed Columns. Copper cyanide species are first converted to hydrogen cyanide (HCN) by acidification, with or without sulfide addition. HCN is extracted by the organic and stripped using a suitable base (eg. NaOH) resulting in a high strength cyanide solution (eg. NaCN) for recycle to the gold recovery process. Continuous pilot plant testwork on HCN extraction using a 40 mm diameter Bateman Pulsed Column demonstrated a cyanide recovery of greater than 99% with final levels of cyanide in solution of less than 10 ppm. These results illustrate the potential of this technology to recycle cyanide and to detoxify final effluent streams.

Jan 1, 2005

By Niraj Bala

Boiler tubes of coal-fired boilers suffer severe erosion-corrosion (E-C). One method to counteract this problem is by the use of therma, spray protective coatings. Cold spray coating process was used to deposit Ni-20Cr powder on SA 516 (Grade 70) boiler steel. The bare as wel, as the coated steels were subjected to cyclic experimenta, studies, in the superheater zone of a coa, fired boiler. The weight change technique was used to establish kinetics of the erosion-corrosion. XRD, FE-SEM/EDS and X-ray mapping techniques were used to analyse the as-sprayed and corroded specimens.

Jan 1, 2010

By C. G. Bruce

"ON NOVEMBER 15th, 1950, the Department of Mines and Technical Surveys announced the discovery of vermiculite near Perth, Ontario. The announcement followed nearly a month of study to determine so far as possible the potentialities of the deposit and quality of the material from surface indications. The mineral was identified by the writer in the field among samples submitted by Mr. Arthur Powers of Stanleyville or, September 22nd, 1950. Within a week of the announcement, mining rights to properties covering a major portion of the deposit had been acquired by commercial interests.Hitherto, Canada has had to import her entire requirements of vermiculite. Prospects of .a domestic supply gave promise of considerable benefit to many industries, particularly the building industry, and to the consumer public. Should the deposit •prove large enough there was also the possibility of exporting to centres in the United States.Field and laboratory studies were continued at the Mines Branch during the winter of 1950-51 as opportunity occurred. It is the purpose of this paper to describe the results of these •preliminary investigations, to attempt to present the Stanleyville occurrence in its proper perspective with regard to similar occurrences elsewhere, and to review the salient features of the vermiculite industry.Properties and UsesVermiculite is a hydrated magnesium aluminum silicate. In appearance it resembles mica, having the same micaceous cleavage, but it differs from that mineral in being very soft, pliable, and inelastic. Colours range from black through dark olive-green and brown to almost colourless."

Jan 1, 1952

"The Upper Mannville unit commonly consists of interbedded marine and non-marine sands and shales, but in northwestern Alberta the unit consists of marine shales of the Spirit River Formation. A thick tongue of marine shale (Clearwater Formation) ex-tends eastward into the Athabasca area below sandy Grand Rapids beds. Correlation of Upper Mannville rocks to the southeast is difficult, but in the Cold Lake area a thick sandy depositional cycle (Mannville ""C"" of this paper) appears to be approximately correlative with the Clearwater Formation. In the Lloyd-minster region, tongues of marine sedimentary rock occur in the lower part of the Upper Mannville unit. Most of the Upper Mannville oil occurs in the Grand Rapids Formation at Wabasca, in the thick ""C"" unit and younger Mannville sands at Cold Lake, and in the Sparky and General Petroleums sands of the Lloydminster region (Figure 2).The Lower Mannville unit was deposited on an erosional surface of considerable relief that truncated the Jurassic and older strata of the Western Canada basin. Continental, probably fluviatile, sedimentation persisted over much of the Western Canada basin during deposition of the Lower Mannville unit, but an Arctic or Boreal sea lay over part of northern Alberta. At the end of the depositional episode, the sea transgressed southward and eastward (Figure 3) and re-worked the Bullhead and McMurray sands of northern Alberta into the glauconitic Bluesky and Wabiskaw sands. Topography on the sub-Cretaceous erosion-al surface had a considerable effect on the deposition of the Lower Mannville (Rudkin, 1965), and the highest hills on this surface were not completely on-lapped by Lower Mannville sediments (Figure 3). The coarser elastic material was derived both from a western Cordilleran region and from an eastern Canadian Shield region (Glaister, 1959, p. 620; Mellon, 1956)."

Jan 1, 1966

By T. Lamb

There are many honor stories about aluminum in the marine environment and many are not based on facts, so they are myths. Myths must be addressed before progress can be made. This paper attempts to dispel the myths and state the facts. A common perception is that aluminum ships cost significantly more than steel ships. This paper illustrates that even though the cost of the aluminum structure is over 50% more than the steel structure, an "equivalent" aluminum naval ship can be built within 7% of the acquisition price of a steel ship. This is possible because of the cascading benefits of the aluminum ship&apos;s significantly lighter weight. Aluminum ships also have a life-cycle cost advantage over steel ships because of reduced maintenance and fuel cost savings.

Jan 1, 2011

By Ashley Tews

In 2005, we automated a forklift-based Hot Metal Carrier to be capable of typical metal transfer operations around a smelter. The project was highly successful and the vehicle has demonstrated hundreds of hours of live autonomous operations to thousands of people from industry and the public. As a result of the exposure and success of the project, we have expanded its focus to demonstrate how various technology components can be utilised to gain benefits in other areas of industrial operations. These include asset tracking, vehicle usage analysis, pedestrian detection and infrastructure profiling. Each of these components was derived from the core autonomous vehicle technology suite and has shown a high potential for improving safety and efficiency of vehicle-related operations, and improved diagnostic processes for measuring deformations of bakes and furnaces. The autonomous vehicle project and its extended technologies are described in this paper.

Aug 1, 2013

By C. Piribauer, E. Feichtenhofer, A. McEneaney

"As part of a major diversification project, RHI AG, through its plant in Drogheda Ireland, has developed a Caustic Calcined Magnesium Oxide (CCM) for use in the Cobalt (Co) & Nickel (Ni) hydrometallurgical extraction industry. In the course of the project, the company investigated the chemical and physical properties of a number of different Magnesia’s used in Co & Ni hydrometallurgy applications and has been able to determine the important parameters for a successful Magnesia for this application. A number of live plant trials have confirmed the results of this testwork and the company is now proceeding to produce this product in commercial quantities at Premier Periclase Ltd., the RHI AG plant in Drogheda, Ireland. This paper will outline the development work conducted by the company and highlight the important chemical and physical properties that make a successful CCM. Much of the research was conducted at the RHI Technology Centre in Leoben, Austria. In addition, a number of external laboratory studies were conducted on behalf of RHI AG. The result of this work has allowed the company to develop a Magnesia product with optimised properties for use in the Cobalt and Nickel hydrometallurgical extraction process.INTRODUCTION Premier Periclase is part of RHI AG, a globally operating supplier of refractory products, systems and services, headquartered in Vienna, Austria. The company produces Magnesia from seawater at its plant in Drogheda, Ireland. While the main focus is on production of refractory grade Dead Burned Magnesia for the steel industry, the plant also produces a number of different grades of Caustic Calcined Magnesia as well as Magnesium Hydroxide products. As part of a major project to diversify the company’s product base, the use of CCM in the Cobalt (Co) & Nickel (Ni) hydrometallurgical extraction industry was investigated. One of the company’s highly reactive grades of Caustic Calcined Magnesia was found to be particularly suitable for this application. In an effort to understand what makes a successful Magnesia for hydrometallurgy the chemical and physical properties of different Magnesia’s used in Co & Ni hydrometallurgy were investigated. This paper and conference presentation outlines the findings of this process."

Jan 1, 2017

By L. R. Bottomer, G. M. Leary

"The Copper Canyon property is located in the Galore Creek area of northwestern British Columbia. Porphyry copper-gold mineralization on the property is notable for its high gold content and close spatial relationship with a distinctive suite of high level syenitic and monzonitic intrusions, and pseudoleucite-bearing volcanic country rocks. The style of alteration and mineralization is similar in many respects to the nearby Galore Creek deposits.The current geological resource of 32.4 million tonnes grading 0.75% Cu, 1.17 g/ t Au and 17.1 g/t Ag is insufficient to support a mining operation, but definition of additional reserves combined with improved transportation infrastructure in the region may change this in the future. The climate, topography and proximity to an active glacier indicate that the most likely production scenario is an underground bulk mining operation, with the ore being milled offsite.IntroductionThe property is located at 57°07' North latitude, 131 °21' West longitude, on NTS sheet 104G/ 3W, approximately 160 km northwest of Stewart and 90 km south of Telegraph Creek (Fig. 1). The Galore Creek camp and airstrip are located 6 km to the west. Current access to the property is via helicopter either from Galore Creek, or from the Bronson Creek airstrip 32 km to the south-southeast.The deposit occurs within the Boundary Ranges of the Coast Mountains, on the north side of the east fork of Galore Creek, which flows northerly into the Scud River and thence westerly to the Stikine River.Topography is rugged. In the deposit area, elevations range from 1130 m to 1750 m. Valley glaciers and permanent snow and ice fields are characteristic of the region at these elevations, and at its southern limit, mineralization is truncated by the East Fork Glacier.The property is entirely above the treeline, and except for areas of moraine cover and talus slopes, outcrop is abundant."

Jan 1, 1995

By J. O. G. Sanderson

Introduction In this paper it is proposed to review the history of petroleum geology in western Canada, to discuss some of the main events which have affected its progress, to mention its relationship to the petroleum industry, and, finally, to appraise its present status and possible future importance. It will be useful first to consider the meanings of the terms petroleum geology, petroleum geologist, and the petroleum geology of a terrain. Petroleum Geology. - In simplest terms, geology is the science of the earth. Hence petroleum geology is the science of that portion of the earth that encloses pools of petroleum. The systematic delineation and study of stratigraphic geology began about 1820. The systematic development and study of petroleum geology started about 1910. It is a relatively immature branch of geology. Petroleum Geologist. - This term may be applied to a fully qualified geologist who is engaged for a time, be it a job, a contract, or a lifetime, in the work of finding and developing deposits of petroleum and related substances. No man may properly be called a petroleum geologist who is not first a fully qualified geologist.

Jan 1, 1946

By J. F. Boux

"The study of the total utilization of fly ash has involved all of the known technology in the processing of this waste material into useful products. In addition, a complete knowledge of all the possible uses of fly ash and its products in the market area was probably the most important factor in evaluating the theory and practical feasibility of the total utilization of fly ash from a single large supplyLaboratory tests carried out on the separation of fly ash into different fractions were shown to improve its value and utilization. Four main fractions were studied: a fine pozzolanic low-carbon fraction; a coarse fraction for light-weight aggregate production by pelletizing and sintering; a high-iron fraction; and a carbon-rich fraction. The term ""beneficiation"" here refers to a process of separating fly ash into more useful components.Laboratory and pilot sinter strand tests were employed to optimize the sintering capability and the quality of the heat-hardened pellets through a study of the agglomeration cycle in four principal heat zones, under controlled conditions of air flow, temperature and atmosphere, and including the controlled sizing of pellets.The suitability of the heat-hardened pellets as light-weight aggregate was evaluated in test batches of concrete, which were compared with concrete containing commercial lightweight aggregate of established quality.A study of beneficiated fly ash pozzolan as a partial cementitious binder component in normal and high-temperature cured concrete was reported in a paper at the re-cent Second International Fly Ash Symposium.Samples of raw and beneficiated Lakeview ash were compared with samples of other established high-quality fly ash pozzolans. The evaluation indicated the usefulness of beneficiated Lakeview ash as a pozzolan. Economic studies indicated that to accomplish the primary objective of total utilization of any single source of fly ash (in this case. fly ash from the Lakeview Generating Station, producing approximately 400,000 tons per year), a broad knowledge of the technology of various mineral processes was essential.The design of the fly ash processing plant had to be based on the disposal of all the raw fly ash produced by the generating station. This is contrary to the normal design of a processing plant in which raw materials are supplied and produced according to product demand. The design, therefore, had to be of such flexibility as to pro-duce as wide a variety of products as possible, and the ability to market them had to be well researched and understood."

Jan 1, 1970

By C. T. Bischoff

Introduction Air conditioning is a term which has come into common use only during our generation. By definition, it means the positive and accurate control of temperature, humidity, movement, purity, and component constituents of the atmosphere within an enclosure. Claiming such results for Noranda&apos;s ventilation system, or for that of any other large mine, at present would be an idle boast. However, we are working toward that end with considerable success. Modern underground ventilation at Noranda dates back about six years. The later development of air conditioning is in its fourth season, but still in the experimental stage. Various ingenious methods have been devised to cool mines which, because of climatic or geological conditions or depth, are excessively warm. A few installations have been made to warm intake air during the winter months where this is necessary. However, the method currently in use at Noranda is unique in that it accomplishes both ends by one process. This method utilizes the freezing and melting of ice to equalize year-round temperatures. Mining Methods While a discussion of mining methods at Noranda is not proposed in this paper, a brief summary may be in order. The Horne mine of Noranda Mines, Limited, has been developed by six shafts, four of which are now active. The most recent, an internal shaft, extends to 6,000 feet below surface, but all of the ore mined to date has come from above the 3,000-foot level. Figure 1 shows a model of principal ore bodies. The area mined is relatively small in plan, considering its vertical extent and the tonnage per vertical foot. Most of the ore lies within an ellipse about 600 by 1,000 feet. While this has certain advantages, the mining of such massive orebodies has presented many problems.

Jan 1, 1947

By S. E. Jackson, L. J. Cabri

Quantitative determination of gold at sub-ppm concentrations in sulphide minerals is an important component of deportment studies for sulphide-gold deposits. Laser Ablation Inductively Coupled Mass Spectrometry (LA-ICP-MS) analysis is preferred for this application because it rapidly and cost-effectively provides spatially resolved (<20 pm), low ppb concentration data for gold and other elements in mineral grains. Recent advances in LA-ICP-MS analysis include the development and application of elemental mapping. Raw signals from multiple line scans or lines-of-spots are deconvoluted and calibrated to generate elemental maps which provide detailed information on spatial variations of gold and other elements within and between grains.

Jan 1, 2011