Search Documents

By W. C. Risley

IN the year 1933, workings at the No. 12 colliery, New Waterford, of the Dominion Coal Company, Limited, had advanced to a point where additional ventilation would soon be required. Furthermore, development of the mine was being .made to practically double the output of coal. Consequently, authorization was given to sink a shaft to the workings. The location selected is on the west side of the mine, about one and a half miles from the slope mouth and on the Low Point shore, some 250 feet from high-water mark. The cliff at this point is 40 feet high, with the land rising on a slope of about 5 per cent to the shaft. Figure 1 shows the location with reference to the colliery workings. The strata through which the shaft was to be sunk were pretty well known from diamond-drill borings previously made, and it was believed that water would be encountered to a depth of at least 250 feet to 300 feet. It was planned, therefore, to seal-off the water by the pumping of cement grout under high pressure. This method was considered to be the most economical means of handling the water during sinking, and would also result in a permanently dry shaft. Figure 2 shows a cross-section of the strata. The permanent shaft hoist and fan were to be electrically driven, which would necessitate the construction of a transmission line between the colliery and the shaft; therefore, it was arranged that the sinking equipment would have electric drive. As all equipment, materials used in construction, and supplies were to be hauled by truck, a roadway 1,800 feet long was required from the main highway to the site, and as heavy loads would be hauled during the fall, winter, and succeeding spring, this road was ballasted with 18 inches of clinkered material obtained from a burned culm bank one and a half miles distant. Actual field work was begun by the Company's own forces early in October. Work preparatory to sinking-in addition to the roadway and trans-mission line-included the construction of the reinforced-concrete shaft collar and fan drift connection; the permanent timber headframe (which was to be used also as the sinking headframe); the permanent reinforced-concrete building to house the shaft hoist and fan drive; and the erection of temporary buildings and installation of all equipment for sinking and lining the shaft and for cementation.

Jan 1, 1936

By Hugh S. Spence

This paper deals with an occurrence of radium ore near Wilberforce, Haliburton county, Ontario, upon which development work has recently been undertaken and which seems more likely to prove of commercial grade than any other deposit' of radioactive minerals hitherto found in Canada. This occurrence is sometimes called the Richardson property, after Mr. W. M. Richardson, the discoverer, and will be so referred to in the present paper. Occurrences of radioactive minerals are not uncommon in eastern Canada, and a number are recorded in the literature. The earliest of such references is probably that in Geology of Canada, 1863, where is mentioned an occurrence of uraninite at Mamainse, on the east shore of lake Superior. The mineral was first described by J. L. Leconte, in 1847, under the name of coracite, and was said to occur in a two-inch vein at the contact of trap and syenite. Search for this locality in recent years has proved unsuccessful. Obalski, in 1894, mentions (1) the occurrence of uraninite at a mica mine near Murray Bay, Que. In 1903, Obalski records (2) tests made on this uraninite by Rutherford and the Curies and the determination in it of the then newly-discovered element radium. In 1901, he mentions (3) the occurrence of uraninite at the Villeneuve mica mine, on the Lievre river, and of samarskite at the Maisonneuve mica mine, in Berthier county.

Jan 1, 1930

By R. K. Collings

The annual production of mineral and mineral-based wastes in Canada is conservatively estimated to be 400 million tons. Over 90 per cent of this amount is waste rock or mill tailings from the mining and mineral processing industry. The remainder are slags and ashes from the metallurgical industry, and sludges from the chemical industry. Because of impurity content, remote location, or both, most wastes have limited usefulness and, indeed, are a liability in that they must be transported to waste disposal sites and contained therein. Certain mineral wastes do, however, have potential value. Some contain small percentages of metals that may be economically recoverable with price increases; others consist of mineral material that may be used for such purposes as road base, construction aggregate, railroad ballast, and in the manufacture of bricks or blocks. Increased interest has been shown in mineral wastes in recent years. This paper reviews the types of mineral wastes available in Canada, briefly describes a number that have potential value, and notes possible uses and related research by CANMET and other organizations.

Jan 1, 1978

By Larson. William

What is Lunar In-Situ Resource Utilization (ISRU)? ISRU involves any hardware or operation that harnesses and utilizes ?in-situ? resources to create products and services for robotic and human exploration In-Situ Lunar Resources ???Natural? Lunar Resources ??Discarded Materials Lunar ISRU Products and Services ??Excavation, Site Preparation, and Outpost Deployment/Emplacement ??Mission Consumable Production ??Outpost Growth and Self-Sufficiency Benefits of ISRU ??Increased science and exploration hardware (instead of consumables) ??Increased safety, crew exploration time, and self-sufficiency ??Technology spin-in/spin-offs help recycling on Earth & space economy

May 1, 2009

By M. A. Perras, M. S. Diederichs

"The Niagara Tunnel Project (NTP) is a 10.1 km long water-diversion tunnel in Niagara Falls, Ontario, which was excavated by a 14.4 m diameter tunnel boring machine. The excavated rock types included limestone, sandstone, siltstone, shale and mudstone. Based on observations and measurements the overbreak was divided into four zones. Approximately half the tunnel length was excavated through the Queenston Formation, which locally is a shale to mudstone. Three of the four overbreak zones were within the Queenston. Zone 1 includes the formations above the Queenston Formation, Zones 2 and 4 are border regimes with little or no influence from St. Davids Buried Gorge and Zone 3 is the area influenced by the gorge. Zones 2 through 4 can be generally summarized as having overbreak as the result of stress induced spalling. Zone 2 marks the transition from slabbing at the Whirlpool contact in the stress shadow to spalling towards Zone 3. The behaviour of Zone 3 is interrupted from the typical high stress behaviour due to the presence of St. Davids Buried Gorge. As the tunnel passed from the gorge the high regional stresses induce spalling, which creates the typical notch shaped overbreak geometry of Zone 4.Three modelling approaches were used to back analyze the brittle failure process at the NTP: damage initiation and spalling limit, laminated anisotropy modelling, and ubiquitous joint approaches. Analyses were conducted for three tunnel chainages: 3+000, 3+250, and 3+500 m because the overbreak depth increased from 2 to 4 m. All approaches produced similar overbreak geometries to those measured. The laminated anisotropy modelling approach was able to produce overbreak depths and chord closures closest to those measured, using a joint normal to shear stiffness ratio between 1 and 2. The back analysis results were able to produce sets of stress and strength inputs for different sections of the tunnel at the transition from overbreak Zone 3 to 4. The back analysis procedure demonstrates the importance of including the anisotropic stiffness in the numerical modelling approach to correctly capture the overbreak geometry and deformations around underground excavations."

Jan 1, 2015

By K. van Warmerdam, M. Pearson, C. Kember, D. McMullen, M. Thayer, C. Ugarenko

In July 2012, Hatch Ltd. and Air Products & Chemicals Inc. completed construction and commissioning of a 4000 tpd O2 cryogenic air separation unit (ASU) for Barrick Gold’s Pueblo Viejo Project located in central Dominican Republic. The ASU produces high pressure gaseous oxygen, which is used for the oxidation of refractory sulphide ore within the pressure oxidation (POX) circuit. As a result of the project’s remote location and tropical climate, many challenges were faced over the course of construction, commissioning and start-up of the ASU. These challenges included adequate preservation of equipment due to dusty and humid site conditions, final assembly and erection of the cryogenic distillation columns on site, limited spare parts inventory/availability, and an unfinished power source for plant commissioning. This paper discusses the steps taken by Hatch and Air Products to successfully design, construct, commission and start up the largest stand-alone ASU plant for a POX application in the metallurgical industry.

Jan 1, 2014

By Eddy Dénommé, Deni Villeneuve

"Niobec mine, a producer of pyrochlore concentrates since 1976, became a producer of ferroniobium in 1994 and achieved accreditation to the ISO 9002 standard in 1995. The goal of ISO 9002 is to ensure that the products supplied to clients regularly meet their specifications, through explicit work standards and procedures throughout the production process, from deposit appraisal to ferroniobium production.A key element of ISO 9002 implementation at Niobec consists of the quality control procedures applied to the raw materials: the ore fed to the mill and the pyrochlore concentrate fed to the reduction plant. These controls extend from exploration, deposit appraisal, mine planning and reserves estimation, mining, mineral processing and, finally, ferroniobium production. The implementation of ISO 9002 has allowed more efficient control of the quality of the final product sold to clients. It requires interactive team work, the role of the geologist being to relate all information pertaining to raw material and product quality to the geological framework of the deposits."

Jan 1, 1997

By Håkan Schunnesson, Kirsten Holme

"When mining high grade, narrow ore bodies, the mining method often implies a very detailed knowledge of the ore contacts to avoid unacceptable ore loss and waste rock dilution. During the past decade, the use of microprocessor based drill monitoring equipment has become an accepted technique, even for percussive drilling. On the basis of the recorded drill performance, such as penetration rate, torque pressure, thrust etc., a fast evaluation of the lithological sequence of the ore zone can be made. In order to evaluate the potential of percussive drill monitoring to pro-vide detailed information of the geometry of the ore body, the technique was tested in the Viscaria copper mine in Sweden during 1996.To provide understandable information to the mine geologist, great emphasis was placed on the separation between the drilling response generated by variations in rock conditions from variations caused by the operator and the drill system. Due to the complicated geology in Viscaria, the drilling response presented to the geologists was separated in two independent signals, one representing the hardness of the rock and one representing the in homogeneity(fracturing) of the rock. With those signals a good separation between different rock types in the ore horizon was achieved.The experience from the Viscaria copper mine is that drill monitoring not only can be used to locate contacts between rock types, but also to characterize rock conditions and, often, also to specify the exact rock type present. Because it is possible to get the drill monitoring information very quickly it is a valuable complement to diamond drilling for increasing the specific knowledge of the geology and the ore body."

Jan 1, 1997

By G. V. Fernandez

Sociedad Minera Cerro Verde S.A.A leaches secondary copper sulfides. In recent years, the mine has introduced innovations that have improved the management of mineral crushing, agglomeration, curing, and leaching. The crushing plant, for example, uses the concepts of degree of balance and percentage of time in an operationally balanced state which, displayed in real time, facilitate more intensive and uniform utilization of the crushers. High agglomerate quality is ensured with the correct dose of moisture, which is adjusted to the changing characteristics of the mineral through the use of electrical conductivity measurements. The amount of acid used for curing the agglomerate is also adjusted by using quality control information. Finally, the stockpile irrigation regime is managed using the criteria established by the "Lixiviant Request Rate", which optimizes the addition of leaching solution, creating such benefits as faster recovery, and reduced acid and energy consumption.

Jan 1, 2007

By K. J. Heale, G. G. Richards, D. J. Rioux, R. L. Stephens

Slag fuming has remained a key process for the recovery of Zn, Pb, and minor elements in the integrated flow sheet at Teck Cominco's Trail Operations for more than 75 years. Since the start-up of the KIVCETTM process and the #3 slag fuming furnace in 1997, a range of process intensification projects have been completed to improve metals recoveries and throughput based on improved process control, mechanical modifications, and, most recently, the implementation of oxygen enrichment of the blast air. This latter project, initially named 'nitrogen depletion' and now 'nitrogen oxygen performance enhancement' (NOPE), is the primary focus of this paper. NOPE reduces the amount of heat required to heat the inert nitrogen gas, and therefore more of the energy input can be used for reduction. It also frees up boiler capacity because the inert nitrogen gas does not then have to be cooled down. A dynamic METSIMTM model was developed to determine the opportunities to improve the process capacity and heat balance to both assist with justifying the project and to verify the observed furnace behaviour. Several process safety management issues were also addressed and a few key minor mechanical modifications were made to allow the project to proceed to commercial implementation at 25% blast air oxygen enrichment. Short term plant trials have confirmed the model predictions. The first three months of a long term, continuous trial showed a 6% increase in zinc fuming rate from average furnace performance despite the implementation of a KIVCETTM fluxing change to assist with minor element recovery that was expected to negatively impact the zinc fuming rate by 3 to 5%. This encouraging result is also in line with the model predictions.

Jan 1, 2008

By Peter Cunningham

Teck Facts and Figures ? Employ more than 14,000 around the world, includes: ? Over 8,600 in Canada (close to 7,800 in British Columbia) ? Close to 2,000 in Chile ? Over 2,700 in Peru ? Approximately 600 in U.S. ? Hundreds more in exploration around the world ? Total capital expenditures ? $1.8 billion for 2012

Aug 1, 2013

By J. Budac, E. Krause, C. L. Stewart, D. Wrana, S. W. Laundry

"As part of an over-all arsenic management strategy, Inco has developed a novel process that converts a by-product high moisture copper/arsenic sulphide precipitate into a crystalline copper arsenate suitable for the manufacture of wood preservation chemicals.The copper/arsenic sulphide precipitate is atmospherically leached with oxygen and sulphuric acid, producing a crude (blue) copper arsenate precipitate, elemental sulphur, and a copper and nickel containing solution. The blue copper arsenate is dissolved with sulphuric acid, the molar Cu/As ratio is raised to 2, and a crystalline copper arsenate (olivenite) is precipitated by the addition of sodium carbonate. Dissolved copper is recovered using metallic nickel (or matte) and elemental sulphur, to produce a low-moisture (low-arsenic) precipitate suitable for standard nickel-copper processing.The process was successfully piloted at Inco's Manitoba Division between September 1990 and June 1991. The copper arsenate product typically analyzed 43% Cu and 25% As, and the moisture content was about 10%."

Jan 1, 1995

By John C. Wilmot, Robert E. Brewer, Royce J. Smith

In March 2003, Phelps Dodge started up an innovative pressure leach facility for processing copper concentrates at the Bagdad mine in Arizona. This paper describes the development of the concentrate leaching plant at Bagdad and the operational results from start up to present. Optimization efforts and an approach to mineralogical modeling of the concentrate to calculate oxygen utilization are also presented.

Jan 1, 2004

Mining Equipment Challenges Equipment Availability Unplanned downtime Maintenance Costs Secondary damage and catastrophic failures (T282 $750k) Emergency work is 4x the cost of planned work Inspections Troubleshooting time Incorrect repairs (parts, labor, lost production) Equipment Life Mis-operation of equipment

May 1, 2013

By T. Hidayat, D. Shishin, V. Prostakova, M. Shevchenko

The chemical compositions of copper feed streams are becoming increasingly complex following the growing demand for metals and corresponding shortages of primary sources. The optimisation of process conditions requires an accurate description of phase equilibria and thermodynamics. Integrated experimental and thermodynamic modelling research program on the characterisation of the complex, multi-component, multi-phase gas-slag-matte-speiss-metal-solids Cu2O-PbO-ZnO-Al2O3- CaO-MgO-FeO-Fe2O3-SiO2-S-(As-Bi-Ni-Sb-Sn-Ag-Au) system is being carried out to support companies undertaking the pyrometallurgical primary production and recycling of copper. The experiments involve high temperature equilibration in controlled gas atmospheres, rapid quenching and direct measurement of equilibrium phase compositions with quantitative microanalytical techniques, including electron probe X- ray microanalysis and Laser Ablation ICP-MS. The thermodynamic modelling is undertaken using FactSage computer package with advanced thermodynamic solution models. The continuing development of research methodologies has resulted in significant advances in research outcomes. Implementation of the results of these fundamental studies involves an ongoing collaboration of researchers and industry technologists. An overview of recent progress in research, implementation and applications in industrial practice are given in the paper. INTRODUCTION Rapidly developing technologies increase the demand for various metals in number and volumes. Modern technological devices such as mobile phones, computers, other electronic devices, have dozens of metals—all those metals have to be a) produced and b) recycled. The fast transition in mobility from fossil energy delivered through combustion to renewable energy first stored in bakeries and delivered through electric engines introduce a significant change in the metal demand in terms of both type and volume of metals. Pyrometallurgy is playing a key role in supporting these changes in our industrialised society.

Jan 1, 2019

By G. J. Birnie

Introduction The preparation of the following paper has been undertaken in the belief that a description of the development methods and equipment used at Lake Shore, at the present time, will prove of general ? interest. Working depths of nearly a mile and a half in shaft sinking and of more than one mile for stoping operations have imposed problems not encountered at shallower horizons. Among the problems contributing to the difficulty of mining at extreme depths might be mentioned: Rock pressures Ventilation Hoisting Shorter work period at the face Geological considerations In the main, the effects of these factors add to the difficulty of mining at depth, but it is not entirely true to say that each must necessarily become more pronounced as mining operations proceed to greater depths. Corrective measures may, in some cases, retard the effect and in others may even relieve some of the difficulty. It is proposed here to discuss these features in the light of the experience at Lake Shore, and to present, in some detail, the current practice in shaft sinking and in driving ore and waste passes, raises, drifts and cross-cuts.

Jan 1, 1950

By I. Masters, K. Buban, M. Faris, M. Antonio, M. Collins

"AngloGold Ashanti Brasil, with assistance from Sherritt International Corporation, has recently commissioned a new autoclave for the pressure oxidation of refractory gold feeds at their Corrego do Sítio operation in Brazil. Design of the new plant, including feed acidulation, pressure oxidation, oxidized solids washing and solution neutralization circuits, was based on the results of test work conducted by Sherritt at their pilot plant in Fort Saskatchewan, Alberta. This paper describes the results of the pilot plant study as well as highlights of the design exercise.INTRODUCTIONAngloGold Ashanti Brasil (AGA Brasil) has recently commissioned a refractory gold pressure oxidation plant at the site of the original São Bento operation in Brazil. The design of the São Bento pressure oxidation facility was based on Sherritt technology; Sherritt carried out the original process development test work in the mid-1980s, provided a process design package and detailed specifications for critical pressure oxidation equipment and participated in the training of operators and commissioning of the plant. The São Bento plant was operated between 1986 and 2007, when the original ore body was exhausted (Silva et al., 2004). AGA Brasil purchased the facility from Eldorado Gold in 2008, with the intent of refurbishing the plant to process refractory gold concentrates produced from the nearby Córrego do Sítio mining area.Sherritt International Corporation has a long history in the development and application of commercial pressure oxidation and pressure leaching processes. Sherritt’s development of technology for the pressure oxidation of refractory gold ores and concentrates commenced in the 1980s in collaboration with Homestake for application at the McLaughlin project in California. This was followed by several commercial applications in Canada, Papua New Guinea and Brazil (Berezowsky et al., 1991). More than thirty pilot plant campaigns investigating the pressure oxidation of refractory gold ores or concentrates have been conducted by Sherritt since the 1980s, and projects with Sherritt contributions to the process development studies and/or engineering design account for about half of the commercial plants that have operated to date with this type of process (Collins et al., 2011a; 2011b)."

Jan 1, 2012

By J. -F. Blais, M. -O. Simonnot, P. Charbonnier, J. Mocellin, Université de Lorraine INRA, G. Mercier

"Huge amounts of air pollution scrubber sludge have been generated during ferromanganese production using blast furnace. These residues have been historically deposited in ponds near steel making plants. They are very rich in zinc, manganese and lead (5 to 40 %) and also contain aluminum and iron. Considering the market value of these metals, brownfield sites can now be used as secondary resources. These ponds also have to be cleaned up to meet the environmental regulations.We have developed a hydrometallurgical process to recover Zn, Mn and Pb in order to produce valuable compounds of Mn and Zn and recover the final Pb residue by pyrometallurgy. The Zn and Mn compounds need to be pure enough to be economically valuable. Batch laboratory tests were carried out to determine suitable selective leaching conditions. The investigated operating conditions were acid concentration, pulp density and temperature. Optimal conditions to maximize zinc extraction (100 %) and manganese extraction (95.9 %) were found using sulfuric acid and sodium metabisulfide. The final residue contained 14.8 to 23.8 % of Pb. Then, Zn was recovered in the form of ZnO or ZnS by precipitation and Zn metal by electrowinning, while Mn was recovered as MnCO3 with a fairly acceptable concentration of impurities.INTRODUCTIONFerromanganese has been produced by pyrometallurgy in much of Western Europe for centuries. Use of wet scrubber to remove pollutant and dust particles from gas stream was common for most of these operations. Those residues contain high concentration of Zn, Mn and Pb. They have been left to decant in settling ponds installed close to the steel production plants. They now constitute heavily contaminated artificial soils. Those sludges are so contaminated with Zn, Mn and Pb that they can be used for metal production. Currently, no method is available to decontaminate these residues and recover Zn, Mn and Pb. Therefore, an approach considering these brownfield sites as secondary resource is in development. Doing so would achieve two goals, decontaminate the site and produce metals.. (Huot, Faure, Biache, Lorgeoux, Simonnot, & Morel, 2014a; Huot, Simonnot, Marion, Yvon, De Donato, & Morel, 2012; Huot, Simonnot, Watteau, Marion, Yvon, De Donato, & Morel, 2014b)."

Jan 1, 2016

By J. P. Mogan, E. D. Dainty, K. Katsuyama

"The Volvo BM 861 U articulated truck is one of the few underground diesel units manufactured by an organization which shares the same corporate roof as the engine manufacturer. As a consequence, the unit has provided an opportunity for the characteristics of the entire system- turbocharged aftercooled engine, transmission and exhaust scrubber- to interact to minimize emission levels. The performance of the components of the system, as evaluated by full-scale dynamometer testing, is summarized. The over-all effect of the various innovations was a 38% reduction in the recommended ventilation level over that of the bare engine.IntroductionThe Mining Research Laboratories of Energy, Mines and Resources Canada is required, as part o f the certification service of the Canadian Explosive Atmosphere s Laboratory, to test the exhaust emissions of diesel engines, and to recommend appropriate amounts of fresh ventilating air to minimize the risks to health of underground personnel working with, or in the vicinity of, such diesel engines. Volvo BM AB of Sweden made application for the certification of the BM 861 U truck during a period in which EMR personnel were engaged in a number of research projects concerned with improving the environment in dieselized mines. One such avenue of research was the venturi or high-energy scrubber; as the BM 861 U was equipped with this type of scrubber , EMR and Volvo BM agreed to cooperate in a considerably more extensive investigation than would be normal for a certification application. The outcome of some of this research is summarized in this paper."

Jan 1, 1981

By J. C. Ingram

IT SEEMS particularly appropriate that, in celebrating its Diamond Anniversary, the Canadian Institute of Mining and Metalturgy chose our Province of British Columbia as its locale in this, our own Centennial year. I am sure your organization is justifiably proud of its achievements and growth over the period of its sixty years, and we, for our part, are justifiably proud of our growth over our first one hundred years. With your kind indulgence I pro-pose to talk to you today about our industrial growth, or, to put it an-other way, to highlight, historically, our progress in industrial development over the past one hundred years, and to take the liberty of speculating on what we may reasonably look forward to over the next few years. I am sure, Mr. Chairman, that some may have questioned the appropriateness of a talk on the industrial development of British Columbia to the Canadian Institute of Mining and Metallurgy. However, strangely enough, we in British Columbia owe our origin, constitution-ally and industrially, to the mining industry.

Jan 1, 1958