Search Documents

By Budd B

this paper outlines the operating advantages gained through applying a mine processor (MISA), to various underground and surface operations. On the surface, MISA monitors and/or controls ventilation fans, crushers, fill plant and stockpiles. Underground, MISA monitors and/or controls dewatering pumps, fill reticulation and high voltage electrical distribution on most levels.

Jan 1, 1988

By Aylmore M. G

Samples have been taken from a two-stage industrial gold roaster treating a pyrite/pyrrhotite/arsenopyrite concentrate, in order to describe the mineralogy, composition and surface area of the calcines. Sulphides oxidised to produce a porous magnetite in the first stage and a porous hematite in the second; pyrite predominantly roasted via a pyrrhotite intermediate. Sulphur was eliminated in both the first and second stages whereas arsenic was eliminated in the first but retained in the second, partly as rims on hematite particles. The finer sized particles from the cyclones and electrostatic precipitator, while having the greatest surface area, were the most refractory with respect to gold solubilisation, probably as a result of incomplete decomposition (through short-circuiting) in the first stage, and through a combination of factors such as overheating and entrapment of sub-microscopic gold in the second stage.

Jan 1, 1992

Jan 1, 2004

By Tenorio J. A, Vieira C. B, Sobrinho P. J N

This paper shows a review of bibliography and actual situation of the plastics injection into blast furnace. Some information about results and experimental practice with plastics waste are presented as well as the development of the injection plastics's technique.

Jan 1, 1999

Carbothermal Reduction of Ilmenite Concentrates and Synthetic Rutile in Different Gas Atmospheres

Sep 13, 2010

By P C. Pistorius

Previous mineralogical investigation of all effluent flotation streams of Mimosa mine (Zimbabwe) indicated that appreciable amounts of liberated platinum-group minerals (PGMs) of the Pt-Pd-Bi-Te class are not recovered û despite electrochemical measurements showing interaction between xanthate and such minerals. In this work, the flotation recovery of synthetically prepared Pd-Bi-Te was compared with that of chalcopyrite (a typical fast-floating mineral) and pyrrhotite (a typical slow-floating mineral), with microflotation tests. These indicated Pd-Bi-Te to be a fast-floater with flotation rates exceeding that of chalcopyrite. Predicted flotation rate constants (from the Ralston model) were significantly lower for small particles (with diameters similar to those lost to the effluent streams) compared with those of particle with intermediate sizes. This supports the suggestion that losses to effluent streams are caused by particle size effects.

Jan 1, 2005

By T Raynlyn, A Edenton, M Adam, R J. Holmes, J R. Manuel, N Ware, R Smyth

Due to ongoing demand and increasing depletion of high-grade iron ore resources from large deposits, Australian iron ore producers are developing smaller size deposits to maintain current export levels. The iron grade, mineralogy, chemical and physical characteristics of iron ore fines being mined from different deposits vary considerably. It is therefore imperative to develop long-term strategies to maintain the quality and consistency of iron ore fines while moving to a larger diversity of smaller deposits. Blending is a common practice in sinter plants as it is almost impossible to produce a high performance sinter mixture displaying the required characteristics from one single ore. Blending is also one of the most effective options being used by iron ore producers to ensure the long-term stability of their products while increasing production. When designing a blend, the blend components are selected to support each other to achieve the required overall balanced metallurgical performance of the final product at a relatively low cost. To do so, a fundamental understanding of the key characteristics of iron ore fines and their potential impacts on the iron ore sintering process and sinter quality are required. In this paper, the sintering process and sinter structure have been analysed and the key factors affecting the sintering performance of iron ore fines, including productivity and quality, identified. Under fixed sintering conditions, the granulation efficiency, nuclei stability and the volume and properties of the primary sinter melt are believed to have important impacts on both sintering productivity and sinter quality. Discussion is then focused on the effects of ore chemical, physical and mineralogical characteristics on the key factors identified and in turn the consequences for sintering productivity and sinter quality.

Jan 1, 2009

By E Rubio, N Morales

Currently, mine plans are optimised by using several criteria as objective functions, like profit, life-of-mine, concentration of some pollutants, mining costs, confidence level or ore resources, with consideration of constraints related to production rates, plant capacities and grades. Whilst this approach is successful in terms of producing high value production schedules, it uses a static opening sequence of the drawpoints and therefore the optimisation is made within the level of freedom left by the original opening schedule, and as a result it is far from the true optimal value of the project. This paper presents a model to optimise the sequence of drawpoint opening over a given time horizon. The emphasis is in the precedence constraints that are required to produce meaningful operational sequences considering the exploitation method (panel or block caving), physics considerations and logical rules. Further on, while it applies the standard approach of maximising net present value (NPV), it considers other targets for optimisation, like the robustness and constructability of the plans. Finally, it applies the model to real data to obtain feasible plans by means of this model. The first tests were done varying the production capacity of the mine.

Sep 26, 2011

A continuing demand for exploration geologists, at a level well below that during the mineral "boom" of 1967-1971, will be highly selective. The exploration geologist must be more than the traditional geologist whose primary function has been detailed description of rocks and their recording on a geological map. He must be capable of 1. reconnaissance recognition of favour= able environments for ore mineral concentrations, 2. application and interpretation of techniques of search and evaluation, and 3. evaluation of economic, technological and political interactions that combine to make an ore deposit. Universities have an obligation to their students to provide them with a saleable skill, to educate them so that they can cope profess- ionally and socially, and to provide a mechan- ism by which education can be a continuing process. Humanistic and social studies, develop ment of communication skills, understanding of economic and management principles, ability to assess rock properties that influence extract- ion and beneficiation, and a knowledge of technological developments and limitations are necessary parts of the exploration geologist's

Jan 1, 1974

By B K. Hebblewhite, G Sharrock

The strength and deformation properties of a rock mass are important parameters influencing the design of civil and mining excavations or structures. The mechanical behaviour of jointed rock masses are controlled by the characteristics of discontinuities and the strength of intact rock bridges between discontinuities. To date, analytical, empirical and experimental methods have not captured the key mechanisms controlling the mechanical properties of actual rock masses with non-persistent joints. The emergence of the synthetic rock mass (SRM) in 2007 provides a promising approach for this purpose. In this paper a rock mass with non-persistent joints is analysed with the SRM model based on PFC3D. The influence of joint geometrical parameters on the uniaxial compressive strength (UCS), rock mass deformation modulus (Em) and failure mode is studied. Joint parameters include joint orientation, persistency, spacing and step angle. Prismatic numerical samples with dimensions 300 mm × 150 mm × 50 mm were generated and a sensitivity analysis of each joint parameter on UCS and Em was undertaken. The results show that of the parameters tested, joint orientation has the greatest influence on UCS. Minimum UCS occurs when the angle between the major principal stress and joint surface is approximately 60°. The joint step angle was found to have a significant effect on failure mode and a joint step angle of 90° is the most favourable joint orientation for step-path failure. The importance of joint step angle is highlighted in the discovery of a failure mode bifurcation point at joint step angles of 60° and 90° for joint orientations of 75° and 90°, respectively. For these parameters the failure mode transitions from block rotation to a new failure mode where the coalescence of cracks results in the formation of new small regularised blocks.

Sep 26, 2011

The paper gives details of the performance of a 6-ft. by 6-ft. grate discharge ball mill which was converted into a rod mill of the overflow type and then into a grate discharge rod mill. Proposals for further alterations are outlined.INTRODUCTIONThe mill of King Island Scheelite (1947) Limited recovers scheelite by gravity methods.Crushed ore at the rate of 34 tons per hour is divided between two mills. (6 ft. by 6 ft. and 8 ft. by 6 ft. respectively), the mill discharges being pumped to a common distributor which feeds seven Hummer Screens. Each screen has three 4-ft. by 2-ft. Ton-cap sections and repulping compartments are provided. The screen oversize is returned to the mills whilst the screen undersize is finished grinding section product. A third (6 ft. by 6 ft.) mill regrinding the coarser table tailings also discharges into the common Hummer Screen Distributor.The screen undersize is pumped to a bowl classifier which separates at 200 mesh. The bowl classifier sands are treated on tables whilst the bowl classifier overflow, after thickening, is treated in the slime plant by flotation. The flotation concentrate is further concentrated on vanners and slime tables.A recovery of 80 per cent. is possible by tabling whereas only 50 per cent can be recovered in the slime section. The object of comminution is, therefore, to reduce all the new feed to less than a certain mesh (22 mesh Tyler) with the production of a minimum quantity of minus 200 mesh material. cheelite is, a very friable heavy mineral (Sp.Gr. 6'0) and is therefore susceptible to overgrinding. For the evaluation of grinding performance it is hence advisable...

Jan 1, 1955

By Coskun B

The classification of selective mining units (SMU's) and the assignment of grades to those classified SMU's are very important in open pit mining, especially for precious metal mining. During ore control planning, the classification of mineral

Jan 1, 1998

By M-A Van Ende, N Kumar, I-H Jung

In order to utilise the powerful thermodynamic databases for process simulations, a concept called Effective Equilibrium Reaction Zone (EERZ) was introduced to couple thermodynamic database calculations and reaction kinetics. Using the EERZ concept, many process simulation models for steelmaking processes have been developed within the FactSage steelmaking consortium. After validation of the simulation results by comparing with plant data, the simulation models have been applied to improve plant operations. Several success stories of the improvement of real steelmaking operations are shared. A new user-friendly FactProSim software developed for building process simulations is introduced.

Aug 21, 2024

Rehabilitation has been very effective in the short to medium term in providing a cost effective and reliable means of containing the side effects of land disturbance. However, there is still insufficient data to critically evaluate the sucess of rehabilitation in the long term. There is an urgent need to develop objective criteria to monitor the sucess of rehabilitation. The aim of rehabilitation in Australia has traditionally been to return disturbed land to natural vegetation compatible with the surrounding area. This objective has often been accepted instinctively without adequately addressing alternatives.

Jan 1, 1992

By P Sutton

The global goal of Sustainable Development is not achievable without major changes in the way goods and services are delivered and material needs are satisfied, which requires tremendous innovation in the supply chains and life cycles in which minerals and energy processing take part. Values derived from minerals and metals processing need to be delivered with a fraction of current ecological impacts, which means removing technical obstacles to eliminating waste and emissions in the minerals cycle. The challenge is to find economically attractive ways to get there, through eco-efficiency gains in existing operations, capturing regional synergies, streamlining and greening the materials supply chain, and commercialising new process technology and new products. This paper summarises the outcomes of the Sustainable Resource Processing project, which was designed to provide a strategic analysis of what sustainability means for minerals and metals processing and how that can be effectively translated into technical and business innovation.

Jan 1, 2002

In a coal mine there are many substances capable of ignition under certain circumstances, which can be placed in the following groups: ordinary combustible solids, dusts, liquids and vapours, gases, metals and plastics. There are many factors influencing ignition, including temperature, minimum ignition energy, particle size, explosion pressure level, rate of pressure rise, specific energy content and also explosive limit. Not all are applicable in every case. Frictional ignition of methane is an accident statistic of increasing concern and is considered in some detail. Practical measures that can be taken to reduce the incidence of frictional ignitions are considered, and also possible ways of ignition suppression.

Jan 1, 1981

By Cecala AB

For 20 years the US Bureau of Mines has been researching strategies for improving the physical, social, and psychological work environment of the miner. The products of this program have shown that a consistent link exists between safety and productivity, and the key to this link is the use of effective human factors and management practices. There are specific research findings from the research projects of the Bureau on ergonomic design of mining equipment, redesign of tasks (especially materials handling) to minimize back injuries, human resource management techniques for increasing safety and productivity, and improved shift rotation schedules. Current research is continuing these themes with new applications to high technology mining systems, including computer assisted extraction devices and mine monitoring.

Jan 1, 1991

By Stewart Gillies AD

Resource rent taxes are taxes which only become effective at such a time as a pre-determined rate of return has been achieved by an operation. Resource Rent Taxes have from time to time been considered for implementation in both Australia and New Zealand. The offshore petroleum industry in Australia is already subject to RRT as is the Roxby Downs (Olympic Dam) Mine in South Australia. Both the mining and petroleum taxation regimes in Papua New Guinea include a resource rent tax component called Additional Profits Tax.

Jan 1, 1995

By Partridge AC

The measurement of particle size is very important in many industries. Comments in this paper refer principally to the Mineral Industry and in particular to Coal Mining and Coal Preparation. The objective is to indicate the importance of particle size in process design and process assessment and to describe techniques for particle size measurement and the presentation of results.

Jan 1, 1984

This paper looks at the various stages of development of open stope drilling techniques. Due to the structural nature of the orebodies mined by open stoping it has been necessary to review mining methods. In-the-hole hammer drilling proved to be the solution to many problems encountered in horizontal percussion drilling.

Jan 1, 1977