Search Documents

The introduction of rubber tyred diesel equipment underground in the early 1960's and subsequent design improvements to diesel haulage systems over the past 2 decades has meant that diesel truck haulage has often been the first choice when selecting a haulage system for a new underground mine. Even today only 9% of all vehicles underground are electric powered.However, with the development of more efficient electric haulage systems, the suc-cessful installation of low cost shaft hoisting systems and improvements in conveyor design, alternative haulage systems are appearing as viable alternatives to diesel truck hauling. In particular, the aspects of ergonomic and environmental operating conditions, maintenance and operating costs as well as productivity rates are becoming more and more important in the selection of underground haulage systems. Future develop-ment of existing diesel haulage systems will require that diesel haulage units become more productive, have considerably reduced exhaust emissions compared to existing units and remain the cheapest haulage method for under-ground one way haul distances up to a distance of 3 kilometres. Development of electric truck and associated fuel cell haulage systems

Jan 1, 1985

The Wellington Dam catchment has high value water, agriculture and coal and power generating resources. These conflicting land uses are managed through consultation and regulation. The Wellington Dam catchment is unique in that the Collie Coal Basin is located almost to the edge of the dam and has coal mining and power generation as its primary land use. Currently the dam is only used for irrigation due to its high salinity. The State Government has committed to reduce the damÆs salt levels to below 600 mg/L by 2015 so that it can be considered for public drinking water supply. The coal industry in conjunction with the community and State Government has worked together to enhance the water quality within the Wellington Dam to maximise its value and use by using mine dewater for industry, diverting saline Collie River flows, providing environmental (social) flows and enhancing water quality of mine voids to encourage new industry to the Collie Region. Both surface and groundwater in the coal basin are generally fresh, whereas the salinity in the Collie River East Branch generally ranges between 3000 to 20 000 mg/L and 1700 to 10 000 mg/L in the South Branch. Mine dewatering is currently two to three times greater than the recharge to the coal basin. As a result, all mine dewater is sent to power stations in the area, with excess discharged into drainage lines which flow into the South Branch of the Collie River. To maintain environmental and social flows some groundwater is also pumped to the South and East Branches of the Collie River during summer months. Completed mine voids are used for recreation and options for aquaculture are promising. However, handback criteria are yet to be finalised.

Jan 1, 2006

The use of coal as a fuel for heat and power generation has a long history. During the nineteenth century most of the present combus- tion technologies were pioneered, as shown in Table 1, This period was associated with the "golden age" of coal and its contribution of almost 80% of the world's energy demands in the early,1900s . The decline in the use of coal has been due to the transfer of the heavy transportation area to diesel power, the elimination of coal as a household fuel and the substitution of oil for coal in power plants. Coal remains the major fuel for the electric utility industry and the present paper will be concerned primarily with that application. Table 1 outlines the development of coal tech- nology with the parallel understanding of coal as a material and its behaviour during combus- tion. Clearly many developments in combustion technology have occurred in this century, although most of the processes had been invented in the nineteenth century. Also, the great expanse in coal research of the past few decades has led to a greater understanding of the coal combustion process.

Jan 1, 1987

By O Tiili, A Dixon

Many minerals processing plants need to have greater efficiency in current times and optimise their process performance in order to maintain high profitability. This is even more so in the current economic climate. In the case of large flotation cells, such as TankCell«-300 with over 300 m3 active capacity, ensuring consistent operation and optimal flotation conditions is particularly critical, given the high impact on overall process and throughput of such cells. As there are fewer cells to control and monitor, there is also a lower initial capital cost for instrumentation - the requirements, however, are higher. Despite such compelling reasons, instrumentation and basic control in flotation cells has not changed much in recent years. The standard is still to use traditional feedback (PI algorithm) controls for slurry level and flotation air. A new advanced instrumentation and control package for large flotation cells has recently been developed by Outotec and has been installed at Macraes.In addition to the standard basic instrumentation and control, the new system at Macraes consists of a froth image analysis system, a froth velocity control, and a level control system which utilises adaptive feedforward compensation. There are three TankCell«-300 cells in operation at Macraes since November 2007 and the new control system was commissioned in December 2007.The paper will include comparative data from pre- and postsystem installation and discusses benefits including optimised recovery, improved performance, as well as ease of operation.

Jan 1, 2009

By R Morrison, P Owen

Particle breakage is an essential part of mineral processing. The aim is to reduce run of mine mineral ore to an optimal size for liberating target minerals and for subsequent recovery by separation processes such as flotation. This size reduction is typically accomplished in a series of stages in a grinding circuit tailored to the properties of the particular mine ore. Commonly this involves two or more classes of equipment starting with crushers, followed by SAG mills and then sometimes ball mills. Occasionally, high pressure grinding rolls or other novel devices are substituted. Broadly, energy consumption increases and energy efficiency decreases with the fineness of the material produced by each piece of equipment. For many operations, up to 50 or 60 per cent of total greenhouse gas emissions from a plant arise from the operation of the comminution circuit with the majority produced by the finest grinding parts, such as the SAG and ball mills. Wear of mill liners and grinding media also add to greenhouse gas emissions generated by their manufacture. The need for continual cost reduction and increasing regulatory and social pressure relating to greenhouse emissions create a strong need for improvements in comminution energy efficiency. Traditional experimental and modelling approaches are not well placed to create the required insights into comminution fundamentals or facilitate radical step changes in performance. This paper discusses the role that advanced modelling (based on coupled DEM and CFD) can play in improving the energy efficiency and performance of existing mainstream grinding equipment and in the development of new ones with radically superior performance. Achieving this goal will also require an improved understanding of ore breakage and methods to include sufficiently realistic breakage models within the DEM models. Developmental issues for the modelling and the critical need for validation of the advanced model features are highlighted.

Jan 1, 2004

In the current climate, there is a real need to bridge the gap between theory and the real world mining considerations, and develop viable, cost-effective, high performance thickeners. With a greater need to extract profits from both difficult-to-process ores and lower grade orebodies, coupled with the necessity to produce 'greener', less water intensive technologies, suppliers need to take current thickener designs to the next level and into the 21st century. The complexity of 'getting it right' within a thickenerÆs feedwell, the 'nerve centre' of the thickener, is no small task. Delivering dilution water and mixing this water with incoming feed slurry, addition of flocculant, maximising flocculant-slurry interaction to build aggregate size, minimising unabsorbed flocculant percentage, volume average of solids volume fraction, momentum dissipation ratio, dilution recycle ratio, volume average shear, maximum shear rate at exit, aggregate size on exit, uniform discharge profile and more ù all of these need to occur in the right order and in the right proportions within the feedwell. This paper discusses the genesis and evolution of a new feedwell design, the first major innovation in the thickening industry in over 15 years.

Jan 1, 2008

By S Slusarczyk, Z Kozlowski

Vibration of surface caused by seismic quakes can make a risk to great mining costruction. We have to do with this risk in the Belchatow open cut mine where seismic quakes of various energy and range have occured since the end of 1970s. The seismic risk influence on the mine structure with the special attention to the slopes of an internal dump has been presented. Hydrogeological and geotechnical conditions of the lignite mining and internal dumping of overburden and ash from Belchatow power plant have been considered. Seismic activity in Belchatow open cut from 1979 to 2001 was described and the connection between mine working and seismicity of this area was investigated. The energy and approximate location of the quakes and seismological parameters of the strongest ones observed from 1995 to 2001 were presented. The mechanism of the quake focuses was determined by means of the primary-arriving wave method. Stability of the slopes was evaluated by means of the Fellenius method. It has been found that seismic events occured in Belchatow region may cause only local eboulements whereas there are not any safety risks to the stability of slopes of the internal dump in Belchatow open cut.

Jan 1, 2003

A short overview of the research program of SveBeFo, Swedish Rock Engineering Research, which was founded in 1993 is first given. Then four recent and ongoing projects in rock blasting and explosives engineering are presented in greater detail: 1. Burn Equations for Commercial Explosives. 2. Blast Damage in Contour Blasting. 3. The Role of Gas Pressure in Pit Wall Damage. 4. Fragmentation of Aggregate Rock. The goal of the bum equation project is to be able to control the energy release from explosive charges to the desired part of the expansion curve of the reaction products under various rock conditions. SveBeFo's work has reached the stage where a burn equation for a lab emulsion has been established which can model the influence of charge diameter on the VOD and detonation front curvature in a cylindrical charge quite well. This work now continues with other emulsion recipes. In the blast damage project the goal is to develop techniques and recommendations on how to minimise the blast damage in construction blasting. The project has gained extensive practical knowledge from the blasting of more than 200 holes in a granite quarry under controlled conditions. The cracks in the rock surrounding the contour holes have been cut open and measured. The influence of factors like charge concentration, decoupling ratio, hole and charge size, VOD and time delay in initiation have been investigated. A simultaneous initiation of a group of contour holes with EDD detonators is quite superior to single hole blasts, even when they are timed as closely as 1 ms.

Jan 1, 1995

Longwall mining has historically been considered an application for only deep reserves. This has changed in the recent past as longwall has become competitive with surface mining. Many resources marked for stripping now he in the domain of longwall. Today, the best longwall mines compete with strip mines operating in even the lowest stripping ratios. Longwall mining has become more widely applicable than it ever has been in the past and it is now generally considered the method of choice in situations where high levels of coal production are required. But the best way to use longwall mining has become less certain with the opportunities that highwall access provides. Wall-to-wall mining is the use of retreating longwall developed from and retreating toward a highwall. As a surface mine reaches its ultimate highwall, the opportunity for longwall punch mining or wall-to-wall mining is obvious. There are several clear operating advantages to operating a longwall in this way and where highwalls are available, the best economic decision will generally favor planning a direct approach. Yet wall-to-wall is not applicable in every situation even when highwalls are available. Moreover, the advantages of wall-to-wall mining do not always justify the cost of trenching or box cuts to access coal . However, many tactical advantages of operating from the highwall can be realized with the use of specially equipped blind drilled or raised bored shafts. This paper discusses novel techniques for a shaft assisted mining system which permits the addition of conveyor structure and mine systems from the surface to the face for advance and retreat mining with longwall, shortwall or room and pillar panels.

Jan 1, 1998

By P Licence, M Stevens, P Atkinson, J L. Mauk

The Rahu and Ascot epithermal Au-Ag prospects are two km north of the Karangahake deposit in the Hauraki Goldfield, and all occur in an approximately 6 km2 north-south elongated magnetic æquietÆ zone. The prospects are hosted by andesitic flows, lithic-crystal tuffs and local sedimentary rocks; local silica sinter occurs at Ascot. These host rocks are intensely altered by quartz, adularia, albite, chlorite, pyrite, illite, interstratified illite-smectite and calcite. Several minerals show zoned distributions, such as widespread adularia that overlies more localised and deeper albite. Illite is the only dioctahedral phyllosilicate in several drill holes, but elsewhere it forms a shallow carapace underlain by interstratified illite-smectite with 50 to 90 percent illite. Veins are common with quartz dominating near the surface and calcite becoming more abundant at depth. Local laumontite-calcite veins also occur. Pseudosecondary and secondary fluid inclusions in quartz and calcite at Rahu and Ascot have homogenisation temperatures (Th) that range from 162¦ to 268¦C and 128¦ to 243¦C, respectively. Most inclusions have trapped dilute fluids with salinities of less than 1.9 weight percent NaCl equivalent, but 20 percent of the inclusions have salinities of 2.0 to 10.5 weight percent NaCl equivalent. Calculated paleowater table elevations suggest that the water table at Rahu occurred at 440 m above sea level (asl). At Ascot, silica sinter formed from discharging geothermal fluids (=100¦C) at the paleosurface at ~135 m asl. However the sinter also contains comb quartz with pseudosecondary inclusions that have a Th average of 229¦C, corresponding to a paleowater table at ~430 m asl during inclusion entrapment. Taken together, these results suggest that the Ascot sinter was buried by approximately 300 m of cover material during a major volcanic or tectonic event, and that subsequent hydrothermal fluids formed veins and alteration at Rahu and deposited comb quartz at Ascot.

Jan 1, 2007

By Morrison R. S, Doennilan N

Recent mapping (1989-1992) by the Northern Territory Geological Survey in the Tennant Creek 1:250 000 map sheet area has resulted in substantial revision of the lithostratigraphy of the Tennant Creek Block (Donnellan, Hussey, and Morrison, in press). Briefly, the former Warramunga Group (Dunnet and Harding, 1967; Dodson and Gardener, 1978) is divided into the Warramunga Formation, and an overlying less deformed volcano-sedimentary succession, the Flynn Subgroup. The latter is conformably overlain by the Tomkinson Creek Subgroup of the Tomkinson Creek province in the north of the Tennant Creek Inlier. These two Subgroups constitute the Churchills Head Group which is essentially equivalent to the Hatches Creek Group of the Davenport province to the south of the Inlier.

Jan 1, 1994

One of the most difficult places to ventil ate in any mine is the working face area of an advancing mine heading. With an ever changing configuration, continual modification and extension to the ventilation system is necess- ary to maintain an adequate supply of fresh air and to control mixing and recirculation. Methane emissions and high dust levels as coal is broken and removed from the face area can produce unhealthy and dangerous conditions if ventilat- ion is not adequately monitored. An understanding of the air flow patterns which develop through use of different face ven- tilation systems can be reached by undertaking underground measurements or through observations using physical models. Tests undertaken by the author to determine the adequacy of different system-configurations are discussed together with approaches adopted by others working in the United States. Various new methods have been proposed for improving face ventilation beyond that sustained using conventional brattice curtain or tubing systems. The adequacy of some advances adopted by mining companies to improve ventilation while maintaining output efficiency is discussed.

Jan 1, 1983

By Holcombe R. J, Dobos S. K, Little T. R

Blue amphibole-bearing rocks in the North D'aguilar Block of southeast Queensland occur either as relict pods and lenses within regionally extensive greenschist facies phyllites and schists or as blocks entrained in serpentinite-matrix melange. Epidote + crossite-bearing varieties predominate and formed under conditions consistent with underplating and high P:T metamorphism in a subduction-related tectonic environment. Neither lawsonite nor jadeite has been observed and metamorphic conditions are estimated at 380-4500C for pressures of 0.5-0.8 GPa. High P:T metamorphism occurred during the earliest stages of deformation and was superimposed upon protoliths of inferred Late Devonian - Early Carboniferous age, including mafic volcanics, tuffs and coarse volcaniclastic breccias as well as pelagic and henipelagic sediments, all of which have undergone varying degrees of over-printing to the greenschist facies. Greenschist facies metamorphism occurred during the second phase of deformation and was associated with the formation of mainly flat-lying or subhorizontal structures; it followed the cessation of subduction and occurred in response to either thermal relaxation during uplift or the imposition of regional heating induced by crustal thickening and/or synkinanatic granite emplacement. Uplift and cooling of the high P:T rocks was completed by 260-265 Ma and may have occurred in response to the same extensional processes which gave rise to the onset of rifting in the adjacent Esk Trough.

Jan 1, 1990

By P Duuring

Late-Archean banded iron formation (BIF)-hosted deposits in the Yilgarn Craton of Western Australia are less well understood compared to the larger Paleoproterozoic, Superior-type BIFhosted deposits of the Hamersley Province. The Weld Range greenstone belt, in the Murchison Domain of the Yilgarn Craton, hosts two Archean, high-grade deposits, Madoonga (68 Mt resource at 57.7 wt per cent Fe) and Beebyn (62 Mt resource at 59.6 wt per cent Fe, ASX announcement 2008). Five main types of high-grade (>55 wt per cent Fe) iron mineralisation at Weld Range each display characteristic grades, tonnage, and contaminant levels, which affect exploration strategies and beneficiation methods:1. ‘Residual’ ore formed as a result of two generations of hypogene alteration of BIF. The first alteration phase replaced silica-rich bands with siderite and/or Fe-rich dolomite; the second phase involved the removal of carbonate gangue minerals and the concentration of residual Fe oxide-rich bands in the BIF via volume reduction. The product is a high-grade, high-tonnage Fe orebody, with minor contaminants.2. Magnetite-bearing shear and fault zones cut BIF along lithological contacts. These zones of secondary magnetite formed as a result of the addition of hypogene magnetite via the circulation of Fe-rich, hypogene hydrothermal fluids through BIF. This type of mineralisation produces narrow (low-tonnage), high-grade magnetite-rich ore zones with high levels of contaminants (eg SiO2, Al2O3) due to the difficulty in mining these zones.3. Specular haematite ± quartz-bearing shear and fault zones cut residual orebodies and magnetite bearing structures. They share similar characteristics to magnetite-bearing structures.4. Goethite-haematite supergene ore zones are controlled by brittle faults that cut BIF. These faults promoted the flow of supergene fluids through BIF and resulted in large ore zones with variable Fe grades and contaminants.5. Detrital deposits comprise transported BIF fragments and are intensely goethite-haematite supergene-altered. These orebodies are locally extensive, with moderate Fe grades.

Jul 11, 2011

Distillation of the large and growing greenhouse literature indicates that: ò Global warming has occurred over the past century or more; ò Build-up of CO2 (and lesser greenhouse gases) in the atmosphere is a fact; ò This build-up is likely to cause further global warming. It does not appear possible to conclude that the observed C02 build up and observed global warming are linked; nor is it yet possible to forecast global or regional climate variation with conviction. The dominant greenhouse gas is C02 with about half the warming potential of those gases emitted by man's activities; and about 80% of anthropogenic C02 emissions are from the burning of fossil fuels. Fossil-fuel C02 emissions arg divided about equally between the developed countries of OECD and the rest of the world. However C02 output growth over the past decade was about 4% for OECD and some 40% elsewhere. Population growth and pressure for better living standards will ensure continued higher growth outside OECD. Uncertainty about the impact of increasing C02 emissions on climate, and the long lead-times involved in limiting the increase in atmospheric C02 concentrations, are good reasons for taking action now. Australia accounts for about 275 million tonnes a year or just over 1% of the CO2 emitted from the world's consumption of fossil fuels, and the fight to control global emissions will be won or lost elsewhere. Australia's participation will be by wise conselt and by example. In view of the uncertainties involved, it appears premature to take actions that might place an additional financial burden on our hard-pressed country. However, much can be done now that makes good economic sense and has the added benefit of limiting the growth in Australia's CO2 emissions. Natural gas emits less C02 per unit of energy when burned than either coal or oil. Furthermore, new gas-fired power stations utilise energy at considerably higher efficiency than is the case today with coal or oil. Because of much lower capital costs, there is a compelling economic case for permitting natural gas to compete freely with coal in the Australian power generation market.

Jan 1, 1989

By B J. Monaghan, P Zulli, X F. Dong

In the lower zone of blast furnace (BF), slag trickles down through a packed bed of carbonaceous particles in the form of films, rivulets or droplets. During its downward flow, there are significant interactions occurring between slag and other phases, ie gas and packing particles. In particular, the interaction between gas and slag is closely associated with the key flow phenomena such as loading, flooding or channelling in the lower zone of the BF. With gas introduced laterally through tuyeres and slag flowing downward from the cohesive zone to the hearth, this interaction varies throughout the lower zone and in the cohesive zone:  strong cross-flow of gas relative to the slag occurs in front of the raceway  counter-current flow of gas and slag occurs in the upper parts of the lower zone  both strong cross- and counter-current flow of gas and slag around and within the cohesive zone. These interactions can be linked to furnace irregularities, affecting smooth operation and limiting production. Therefore, understanding the gas-slag interaction and its influencing factors remains critical for BF process control. In the current review, the physical behaviour and key influencing factors of gas and slag flow are initially examined. Numerical models describing gas and slag flows in a packed bed at micro-, mesoand macro-scopic levels, are reviewed. Each simulation approach has its advantages and limitations, as well as unique assumptions when used in BF process modelling. Applications of these approaches to gas-slag flow in key identified functional zones will highlight the differences between approaches and modelling outcomes. As no single approach can fully address all aspects of gasslag interactions, an integration of different approaches is considered an effective and beneficial method in providing a more complete understanding of gas-slag flow in the BF process.

Jun 19, 2024

In North-West Nelson the Riwaka Complex, a linear basic intrusive complex, is exposed for approximately 45 kilometres. Some 500 kilometres south, across the Alpine Fault, a linear zone of similar but less well known basic intrusives that may be correlatives of the Riwaka Complex is exposed discontinuously for about 80 kilometres. The Complex was emplaced at several centers along a major tensional fracture zone that developed in upper Carboniferous to Lower Permian time. This fracture zone probably formed in response to the development of a west dipping subduction zone that gave rise to the Permian volcanic arcs in east Nelson and western Southland. The Riwaka Complex contains three rock suites. The Fractionation Suite, characterized by cyclic mineral layering and small scale cumulus banding is the largest and is divided into the Ultramafic, Hornblende and Plagioclase Series, each of which is subdivided into several units. The Cumulus Gabbros represent a restricted but important suite of unusual composition, while the third suite is the late phase Diorite Suite.

Jan 1, 1980

By Van Weert G

Ferrous chloride solution pyrohydrolysis is a successful IICI regeneration process which is carried out in either a spray roaster or a fluid bed. Pyrohydrolysis is not restricted to ferrous chloride only, every metal chloride can theoretically be hydrolysed. In practice, however, the conditions for ferrous chloride pyrohydrolysis differ from those of many non-ferrous metal chlorides eg zinc, lead and cadmium. Hence, a pyrohydrolyser could function as a ferrous/non-ferrous separator, eg an iron oxide and zinc chloride separator. Most pyrohydrolysers operate on solutions, in which case more than 50 per cent of the process energy is needed for heating and evaporating water. However, this disadvantage would be diminished by feeding a slurry to the reactor. Against this background it was decided to investigate the chloridisation of zinc ferrite which is an iron bearing solid with a non-ferrous impurity, and subject to processing and disposal problems. Synthetic zinc ferrite was chloridised in a tube furnace. The gas atmosphere in the tube furnace resembled that of a fluid bed pyrohydrolyser and consisted of HCI, 1120 and nitrogen. Gas composition, temperature, residence time and sample mass were varied. The experiments showed that complete (99.6 per cent) zinc extraction from synthetic zinc ferrite was possible in a simplified pyrohydrolyser atmosphere at 1100 K in four hours. The zinc ferrite was converted into gaseous zinc chloride, and hematite and magnetite solids. It was also found that zinc removal from the zinc ferrite lattice caused not only rccrystallisation of the zinc ferrite into hematite, but also hematite crystal

Jan 1, 1993

By D Wallace, H Guo, B Shen

Appropriate management of the ground subsidence induced by coal mining activities is essential. To assess the effectiveness of grout injection for mining subsidence control, time-lapse ground penetrating radar (GPR) imaging data were collected before and after grouting. The pregouting subsurface responses were interpreted to have changed after grout injection. The changes were caused by injecting the grout materials (flyash and water) into the delaminated strata and permeable fracture zones. The largest distance of the observed GPR event changes at the right end of the main profile is 132 m away from the injection borehole. Although the GPR images could not easily tell if the image changes were caused by the injected ashes or the water, it does suggest that the injection materials had been pushed at least 130 m away from the injection borehole. This is consistent with the borehole scan monitoring, which confirmed that the grout has travelled more than 90 m from the injection borehole.

Jan 1, 2006

By R Dimitrakopoulos, C Paduraru

The optimisation of mine complexes and related value chains is a challenging problem due to the simultaneous presence of a highly-dimensional decision space, integer decision variables, non-linear constraints and recovery functions, as well as geological and market uncertainty. In addition, if the uncertainty is revealed progressively, then decisions need to continuously adapt to new information, which poses additional challenges. Stochastic dynamic programming is a well-known class of methods for addressing problems where a decision-maker reacts to new information. While simplistic applications of dynamic programming using exact representations would be intractable for any realistic mine planning problem, new dynamic programming methods using approximate value function representations have been successfully implemented in the past to address problems of similar complexity. This work formulates the problem of mine complex optimisation as an approximate dynamic program and presents an application of the resulting method to a gold-copper deposit.CITATION:Paduraru, C and Dimitrakopoulos, R, 2014. Mineral supply chain optimisation under uncertainty using approximate dynamic programming, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 415–422 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014