Search Documents

City Resources Limited selected Vanuatu as a target area for epithermal gold mineralization because of its relatively unexplored character and its location on the southwest Pacific rim. During 1985 a systematic program of reconnaissance prospecting was completed on six islands within the Vanuatu group, using a helicopter and a specially designed exploration support vessel with on-board assay laboratory. Within a period of 4 months, reconnaissance prospecting of all six islands was completed, two previously unknown epithermal gold provinces had been discovered, and six major prospects warranting detailed exploration had been identified. Factors which contributed to the success of the program include (i) a flexible management approach, (ii) the mobility and access provided by the support vessel/helicopter combination, (iii) rapid assay turn-around, and (iv) adherence to basic prospecting techniques. The relative merits of various sampling media are discussed.

Jan 1, 1987

By Medhurst TP, Trueman R, Hutchinson IN

A breaker line support (BLS) monitoring system, BLSmon, has been designed and constructed by the CSIRO and installed and commissioned at Laleham No.] Colliery, Queensland. This system was designed to record hydraulic leg pressure and canopy position measurements and relay these, in real time, to the surface. The system has shown itself to be capable of operating on the BLSs without any adverse affect on production. Analysis of the results of the monitoring exercise has shown that rate of change of leg pressures on the BLSs could be used as an aid in the prediction of adverse mining conditions. Under favourable mining conditions the supports were observed to initially unload from the set pressure, this unloading reduced with time and by the end of a typical lift cycle had either ceased or reversed slightly. This behaviour was considered to be due to one of four possible causes, these being; the compaction of floor debris, and/or compaction of the floor, and/or crushing of the roof and /or support creep. The actual cause can only be determined through detailed monitoring of both roof and support convergence. However observational data would suggest that compaction of debris and softened floor material beneath the supports was the most likely cause. The few positive loading rates recorded under these conditions were of short duration and occurred towards the end of individual lifts. Where mining conditions were unfavourable the negative rates of change of pressure, unloading of the support, were reduced throughout a lift, in both duration and magnitude, when compared with favourable mining conditions. Over the same period the positive rates of change were observed to be greater. The rate of change of loading and convergence can be utilised to identify the onset of instability in the lift area. However, before this facility can be utilised by the mine for the reliable prediction of instability more monitored data and sophisticated processing techniques are required.

Jan 1, 1992

By M Robertson

3D photogrammetry is a powerful tool for data capture and interpretation, utilised at all Australian underground MMG sites. In personnel constrained mines, 3D photogrammetry can free up personnel time, improve data quality for resource modelling, as well as benefit other mining departments.At Rosebery one of the challenges faced by geologists was no longer data capture but, rather, avoiding paralysis by analysis from the sheer abundance of information currently available to the department. Although the data had been interpreted, the structural model was cluttered; the geological block model was not incorporating any geological domains captured by 3D photogrammetry, nor was it being utilised by other departments such as geotechnical engineering.The geology department is now focusing on utilising all the interpreted data gained from each photograph heading into an uncluttered, easily understandable model for geologists and other mining departments.Our solutions involve integrating the Leapfrog modelling suite into the process, streamlining the structural model, tailoring the data interpretations for future updates of the block model and training other departments to improve utilisation of the interpreted data. This process also uncovered other benefits for near-mine exploration, and improving our understanding of the deposit’s origin.CITATION:Robertson, M, 2017. The practical use of underground 3D photogrammetry data at MMG Rosebery polymetallic mine, Tasmania, Australia, in Proceedings Tenth International Mining Geology Conference 2017, pp 409–412 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By B J. Wilde

Evaluating the resources and reserves in a mineral deposit requires many interdependent subjective decisions. The decision of stationarity is arguably the most important. This decision includes: the choice of domains that subset the entire deposit, modelling the boundaries of each domain, and understanding and considering the nature of the contacts between domains. Reasonable choices are made in consideration of the geological context, the available data, the goals of the study and the available resources for the study. This paper reviews aspects of the decision of stationarity in modern resource assessment with a focus on quantifying uncertainty and using numerical/statistical tools to help the geomodeller. The use of volume/distance functions to quantify uncertainty in domain limits is particularly important and is presented in detail. The use of contact plots provides help with the continuity of grades across domain boundaries. Realisations are not assembled as a branching combinatorial of all possibilities, but as a set of realisations that provide a measure of uncertainty. This paper amounts to a definition of stationarity for modern resource assessment.

Sep 26, 2011

By P M. Dight

Shotcrete usage in declines and developments has become pervasive as operators strive to achieve production improvements. Issues of mix control, fibreload, thickness control, temperature and curing conditions all play a part in the quality control. Often to overcome some of the quality control issues designers over specify the strength requirements in order to meet their operational constraints. Adherence to the standard civil testing requirements of 28 days moist cured at 21ºC without properly calibrating these results to the changing environment underground leads to contractual disputes. There are a number of standard tests specified including cylinder tests, cored tests, beam tests and round determinate panel (RDP) panel tests. The logistics of storing these samples and then transporting them to concrete testing laboratories without due regard to temperature changes with time can influence the results. All the samples can be readily handled by personnel except the RDP panel. The standard RDP panel is 800 mm diameter by 75 mm thick and requires an ITH machine at the mine and a fork lift at the laboratory to move it around. This paper will examine the possibility of a panel which provides scalable results to the standard RDP panel but can be easily handled by personnel and/or tested on site with suitable equipment. This allows for faster turn around and better quality control for the sample prior to testing. This enhances the identification of quality control issues at the mine and improves safety.

Mar 21, 2011

By L MacDonald, D Molver, D Pepper

Increasing contamination/impurity levels (including arsenic, antimony, mercury etc.) of concentrates is an issue of global commercial and health / environmental significance. With increasing environmental pressures at smelters, penalties for contaminants in concentrates continue to rise, accompanied by lower reject limits. There is a strong incentive for miners to investigate alternative means to remove contaminants in order to increase the value of complex ores and concentrates. This paper discusses the global problem of contamination in complex ores and concentrates, how the Toowong Process technology is a potential solution to this problem, and the opportunities this technology brings to the business of dealing with deleterious elements. CITATION: MacDonald, L, Molver, D and Pepper, D, 2018. The Toowong process for treatment of complex ores, in Proceedings Complex Orebodies Conference 2018, pp 119–121 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By R Knight

The spatial variability of geometallurgical characteristics in a mineral deposit can have significant impact on financial and mine planning, mineral processing, concentrate quality and tailings composition throughout the life of a project. These characteristics that may determine the success of a project are not readily apparent to geologists unless they are integrated with deposit geology and assay data, modelled in 3D and incorporated into resource block models.One of the primary objectives of geometallurgy is to integrate and incorporate various geologic, geotechnical and geometallurgical parameters into resource block models, which typically are limited to in situ tonnes and grade of economic metals. Critical attributes, such as concentration of deleterious elements that affect the project viability need to be identified and integrated into the resource block model early in the exploration stage to predict project profitability and address potential environmental impacts.Using data from a volcanogenic massive sulfide deposit we present an example of the integration of ore geochemistry (cadmium, arsenic and antimony) with the results of preliminary, bench-scale metallurgical test work in a 3D geometallurgical model that predicts subdomains of poor-quality concentrate and tailings containing environmentally-sensitive elements. This critical information was incorporated into the existing resource block model in order to inform both financial modelling and mine planning.This example demonstrates that geometallurgical data can be effectively integrated with geological and assay data using Leapfrog MiningTM software (Leapfrog Mining) early in the exploration stage of a project. Three-dimensional representations of geometallurgical data can be created directly using primary additive data, as well as from proxies of non-additive parameters. Resource block models can be updated continually with new information as the project passes from exploration through production. In addition, the software allows for 3D visualisation of the characteristics of the materials that will eventually constitute the mill concentrate, tailings, and waste. This study emphasises the critical importance of establishing a systematic geometallurgical approach early in the exploration stage that can be continuously updated with new information throughout the life of the project. In the example that we present, sulfide ore that had otherwise been identified as high-value (in the absence of geochemical and metallurgical data) turns out to be low-value ore due to concentrate penalties and increased environmental impact.

Sep 5, 2011

I WISH to express to the members of the Institute my sincere appreciation of the distinction which they have conferred upon me by again making me their president. It also gives me great pleasure to once more welcome the Institute to Mount Lyell.Since your last visit certain improvements in plant have been made, which I trust you will have found interesting, and which show that, though located in a remote corner of the world, we are abreast of the times.The opportunities which a recent lengthy trip to America has given me to observe the degree of interest which our local smelting practice continues to arouse in metallurgical circles make it seem appropriate that I should take advantage of your visit to lay before you some detailed information on the more practical features of pyrite smelting, particularly as carried out at Mount Lyell. There are only a few places in the world where the method is now being practised in approximate purity-only about half...

Jan 1, 1915

Early in 1950 a new laboratory was set up to deal with problems in mineragraphy, petrology and metallography. This paper describes the equipment, the organisation and association of the laboratory with the various departments of the company, the work that has been done and future plans.At Mount Isa it was soon realised that the microscope would play a most important role in mineral dressing problems and aiding geological research.As early as 1928, R. J. Colony submitted a petrographic report on Black Star ore for Consolidated Limited; much later, in 1934-5 Dr. Grondijs published for Mount Isa Mines Limited a preliminary study of the Mount Isa orebody, followed by a mineragraphicinvestigation of mill products, and in 1937 a Study of Mount Isa Ores by H. GrondIjs and C. Schouten appeared in Economic Geology, for June-July. Other papers dealing with the petrology and mineragraphy of Mount Isa ores are appended at the end of the paper.The mill research metallurgical staff has endeavoured to incorporate mineragraphy in solving milling problems and determining the effectiveness of laboratory as well as examining minerals sent in by the geological department.For many years the amount of equipment available was limited and much of it was locally made or improvised. An improvised briquetting machine, and grinding and polishing lap gave moderate results in conjunction with an old, but serviceable, Leitz microscope. However, for more detailed and accurate work not possible with improvised equipment, many mineragraphic problems were sent to specialist in.

Jan 1, 1953

This paper discusses some topical issues on the mining administration and legislation fields including:  1. Licensing û Administration and associated specialist functions including:Processing and volumes of mining privilege applicationsFuture organisation and possible decentralisationSpecialist staffFacilitiesGuide to the Mining Act 1971 2. Mining Amendment Act 1981 Transitional procedures 3. Planning Tribunal First hearing of objectionsPoints of principle resulted there from 4. Quarries and Tunnels Bill Currently before Parliament û implications for metallurgical mining

Jan 1, 1982

By J Salaya, J Kwak, L Keeney, S Dehkhoda

In addition to volatile commodity prices influencing decision making, in recent years, social and environmental performance have become important decision drivers within the mining industry. There are increased demands from stakeholders, communities, and governments to ensure that raw materials are mined, processed and refined responsibly. The industry also faces the challenge of better managing its waste, which has led to severe consequences when not done properly. The high commodity prices of the late 90s and early 2000s encouraged larger economies of scale and drove mining companies to extract large volumes of rock for separation and concentration at the downstream processes. Over time, as ore grades dropped, the cost of mining escalated and tailings volumes grew. This arduous process also caused strains on recovery cost and performance. Scarcity of water and energy resources coupled with increased production demands and higher operating costs are putting pressure on companies to find innovative ways to increase mining intensities. Hatch’s value chain optimisation methodologies, specifically Grade Engineering® and early waste rejection of the mine, have been of interest to intensify operational performance and minimise waste generation. Enabling preconcentration of the plant throughput, the methodology has significant potential to improve overall metal production and reduce water and energy intensities, whilst minimising wet tailings. Using representative data from real world mines, this paper reports on a case study that evaluates the impact of preconcentration using sensor-based ore sorting on downstream process improvements as well as energy, water and tailings reduction. Financial and economic viability of this technique is presented for both brownfield and greenfield implementation cases. The results show that business case for preconcentration is best when: the distribution of metal in the run of mine ore is negatively skewed and left tailed; mining costs are low; energy, water and tailings management costs are high; and low cost methods of recovering pay metal from low grade material are available.

Nov 10, 2020

By K Marler

The Water Act 2000 includes provisions to manage the take of overland flow water. Overland flow water is water that runs across the land after rainfall either before it enters a watercourse, after it leaves a watercourse as floodwater, or after it rises to the surface naturally from underground. To ensure adequate environmental flows and long-term security for water users, it is necessary to balance the amount of water taken as overland flow water and the amount left to flow into watercourses. A water resource plan made under the Water Act 2000 establishes the basis for the sustainable management of this type of water. Of the water resource plans that have been prepared for Queensland catchments, six include provisions to manage the take of overland flow water. This paper discusses some of the common features of these plans and the management approaches adopted. The paper identifies and explains key aspects of the Water Act 2000 framework for managing the take of overland flow water by the mining industry. In particular it explains key concepts of this framework, such as the ability to take overland flow water using existing works, uses of overland flow water that a water resource plan permits, situations where a specific entitlement under the Water Act 2000 is required, and the means for controlling works that take overland flow water. Future initiatives for the regulation and management of overland flow water are then identified and particular challenges for the mining industry associated with using overland flow water highlighted.

Jan 1, 2006

By M I. Pownceby, S P. Suthers, V Nunna, G J. Sparrow

Global demand for iron and steel has increased substantially over the past 20 years and there has been a greater focus on developing suitable processing options to treat low-grade hematite-goethite ores containing higher levels of silica and alumina impurities. The processing applicable to reduce the impurity levels in these lower-grade iron ores depends on their mineralogy and a thorough understanding of the process dynamics associated with the separation technology. Different separation technologies used to remove silica and alumina from low-grade iron ores were reviewed. The major concentration methods that may be applied to upgrade lower-grade lump iron ores include magnetic separation, wet and dry heavy media separation, and air-pulsed jigging. The technologies applicable to beneficiating iron ore fines include wet and dry gravity and magnetic separation, flotation, and roasting followed by magnetic separation. It is necessary to investigate the application of separation technologies on a case-by-case basis to select economically viable beneficiation strategies suitable for the particular low-grade iron ore. A commercial flow sheet is expected to involve the implementation of several separation technologies.

Nov 8, 2021

By V Pfannenstiel

The United States (US) coal mining industry has been working under comprehensive planning, operating and rehabilitation regulatory requirements for nearly 35 years. The public desire for environmental protection during mining and rehabilitation following mining to achieve post-mining land use and sustainability goals has been a major factor and continues to influence the process. Mining companies have evolved operations to achieve outcomes that address the desired goals and regulatory requirements cost-effectively and successfully. Over the 35 year regulatory period, requirements for more diverse topography, specialised revegetation communities, landform stability and assured sustainability have increased and become more complex. These challenges are effectively met by maximising integration of mine planning and operating with the rehabilitation process. Rehabilitation is then implemented in a more timely and efficient manner and with effective results that achieve desired outcomes, commonly with added value. Peabody Energy (Peabody) has taken this approach in its US operations and this paper discusses an integrated approach and illustrates learnings and results with examples from several of its western US operations.CITATION:Pfannenstiel, V, 2012. Integrated planning, mining and rehabilitation for effective results and sustainable land use - A western United States perspective, in Proceedings Life-of-Mine 2012 , pp 219-232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

Towards Improved Hydrocyclone Models - Contributions from Computational Fluid Dynamics

Sep 13, 2010

A brief history of the significant haulage truck feature changes and the factors that influenced those changes during the 60's and 70's provide a basis for forecasting the changes that can be expected in the 1980's. A review of the impact factors and changing requirements that currently exist that will create changes. Define the critical requirements of a successful haulage truck design and discuss the availability of bigger engines and better electric drive componetry to provide deeper pit capability and improve reliability. The Unit Rig Trolley Assist System to provide improved productivity and diesel fuel savings and an economic analysis to evaluate the Trolley System is covered. The Unit Rig Automatic Truck System for a driverless truck is covered in concept and discussed from the point of view of the experience in a test in a New Mexico mine. INTRODUCTION A good basis for trying to forecast what is going to happen in the future is to go back a little bit in history, to see what the influencing elements were in different periods of time as a foundation for the forecast. INFLUENTIAL FACTORS IN THE 1960'S If you look at the truck development that occurred in the 1960's, there were some identifiable factors that give us insight. (See Fig. 1) Several things happened at the beginning of the 1960's. Mechanical drive haulage trucks were introduced that were

Jan 1, 1982

By D Giles, A C. Bailey

In the first 20 years of the 21st century, just over 20 per cent of Australian mineral exploration expenditure was dedicated to iron ore, totalling >A$8 billion and >30 million metres of drilling (Australian Bureau of Statistics, 2021). Improvements in the cost, efficiency, safety, reliability and data quality of drilling have the potential to deliver significant productivity improvements, increasing the probability of discovery and reducing the time from discovery to mining. Currently in its third year of research, Mineral Exploration Cooperative Research Centre (MinEx CRC) is focused on a new set of exploration tools and new ways to deploy those tools which recognise the fundamental importance of collecting quantity and quality data from the subsurface, to enable exploration success for all minerals, including iron ore. MinEx CRC is focused on developing more productive, safer and environmentally friendly drilling methods to discover and drill-out deposits. This includes pioneering work on Coil Tube (CT) drilling technology and innovations in Diamond and Reverse Circulation (RC) drilling techniques aimed at improved drilling optimisation and automation. In parallel, MinEx is developing new technologies for collecting data whilst drilling. This is being undertaken in four separate industry-led projects utilising geophysical, seismic, downhole analytical and 3-dimensional (3D) modelling improvements. A National Drilling Initiative (NDI) is also underway, with two drilling programs completed in 2020. The NDI is a world-first collaboration of Geological Surveys, researchers and industry, which undertakes drilling in under-explored areas of potential mineral wealth in Australia and provides a test-bed for new mineral exploration technologies.

Nov 8, 2021

The following paper outlines the types of employment immediately available to graduates following their university degree, a discussion on mine manager requirements, mentions career advancement and time frames to achieve this as well as providing some key information regarding student vacation work. The author hopes to educate present graduates, as well as inform students of characteristics to develop the most opportunities in life.

Jan 1, 2006

By J Palise

As cities become more populated and the need for tunnelling increases, we continue to dig deeper urban tunnels in more challenging ground conditions. At the same time our expectations for durability and long-term performance are increasing.It has become increasingly apparent in recent years that repairing water leaks in tunnels can be very costly and unplanned infiltration can cause undesirable outcomes for long-term maintenance costs, structural durability and environmental impacts. For this reason, tunnel constructors are investing more time and effort upfront into drainage and waterproofing systems.Tunnel membrane systems are becoming accepted as a necessary part of tunnel construction, however the knowledge surrounding selection of appropriate systems, design detailing and installation methods has not increased at the same rate. Currently Australia relies heavily on International Standards from Europe and the United States with no immediate program in place to establish our own locally relevant industry standards.This paper gives an overview of where the industry in Australasia is heading in terms of adopting relevant standards. Current basic waterproof detailing options for drained and undrained tunnels with success and failure of various methods are also addressed. Finally we look at the Brisbane Airport Link as a case study for how tunnel waterproofing contract methods, design and installation issues are being addressed in context with recent projects including the Epping to Chatswood Rail Link in Sydney, Auckland Northern Gateway Tunnel, Eastlink Tunnel in Melbourne and Sydney City West Cable Tunnel.This paper’s primary objective is to propose guidelines for how tunnel waterproofing could be implemented on large infrastructure projects in the future and to map a path for preparing and introducing a ready to use document for selecting appropriate tunnel membrane and drainage systems whilst implementing detailing methods which are appropriate for local conditions.

Mar 8, 2011

By D Cliff

"Recent underground coal mine incidents have again raised the issue of: under what circumstanceis it safe for personnel to re-enter the mine? Mine rescue guidelines make recommendations aboutthe limits in terms of the circumstances, lives at risk, no lives at risk and training exercises. Theseare based upon percentages of the upper and lower explosive limits. Many factors infl uencesett ing limits for safe re-entry. These include: the representativeness of the sampling location(s),the rapidity of gett ing an underground sample analysed and the rate of change of the atmospherebeing monitored. Value judgements based upon these parameters will then infl uence the sett ing ofa trigger point based upon per cent explosibility. This raises the question of how the percentage ofthe lower or upper explosive limit is established. It is easy to defi ne this when the sampling pointdata sit on the fresh air limit line. However - what value is used when the sample sits somewherein the body of an explosibility diagram? This paper explores the various options and illustratesvarious pitfalls and problems that are faced in making such a determination. These include howthe data are represented and the assumed knowledge of those doing the interpretation."

Jun 1, 2012