Search Documents

By Chen Z, Dong H

This paper describes the autogenous carrier flotation of 0 - 20 ¦m ilmenite using 40 -- 80 }tm ilmenite as carrier. Investigation is made of the influence of main technological parameters on autogenous carrier flotation. The mechanism of autogenous carrier flotation is discussed using extended DLVO theory. The main conclusions are as follows: 1. the smaller the fine particles the more easily they adhere.to carriers; 2. the selectivity of autogenous carrier flotation depends on the selectivity of adsorption of collector. In the autogenous carrier flotation of ilmenite/plagioclase mixture assaying 15.35 per cent TiO2, a concentrate containing 47.17 per cent Ti02 can be obtained by primary separation with a recovery of 93.05 per cent. KEYWORDS: Autogenous carrier flotation, extended DLVO theory, ilmenite, styrylphosphonic acid.

Jan 1, 1993

By R Peiffer, L van Wyk

The Port of Port Hedland is the largest bulk export terminal in the world and is one of Australia’s most important pieces of economic infrastructure. BHP is the largest Port user to support the export of iron ore products from mines located within the Pilbara region of Western Australia (WA). BHP’s priority is the safety and well-being of its workforce and the communities where it operates. In a recent regulatory application to increase export capacity, BHP committed to the deployment of wind fences to reduce wind erosion from stockpiled ore. Wind erosion from stockpiles was identified through inverse modelling as the most significant dust source compared to other sources such as stackers, reclaimers, shiploaders and transfer stations. The primary cause of dust emissions from stockpiles is dust lift-off during high wind conditions. BHP proposed the installation of wind fences across its Port Hedland operations, targeted at reducing emissions from wind dependent sources, primarily stockpiles, by reducing the wind speed downwind of the wind fence. Modelling predicts that installation of the wind fence will significantly reduce emissions from stockpiles, particularly at BHP’s western operations (Finucane Island). To be effective in shielding stockyards and reducing wind speeds, the wind fences are located upwind and as close as practical to the open stockyards. BHP’s wind fence design incorporates learnings from other existing installations and has been tailored for Port Hedland’s cyclonic conditions. The wind fence will be higher than the stockpile height, with a mesh porosity of approximately 50 per cent. The mesh porosity allows some of the wind to pass through the mesh. This reduces the wind turbulence downstream of the wind fence, as opposed to a solid wind fence, which increases downwind turbulence, resulting in increased dust.

Sep 18, 2023

By M D. Griffith

Oct 12, 2022

Black coals occur in most of the major sedimentary basins in Australia. In addition to the better known Permian coal occurrences of the Sydney, Bowen, Oaklands and Galilee Basins, coals of Permian age occur in the Arckaringa Basin in South Australia, the Bonaparte Basin in Northern Territory and the Collie, Perth and Canning Basins in Western Australia and the Tasmania Basin in Tasmania. Coals of Triassic age occur in the Ipswich Callide and Tarong Basins in Queensland, the Tasmania Basin in Tasmania and the Leigh Creek area in South Aus- tralia. Coal bearing rocks of Jurassic age occur in the Mulgildie Basin and Maryborough Basins in Queensland and in both the Queensland and New South Wales portions of the Clarence Moreton Basin and Surat Basins. They also occur in the Perth Basin in Western Australia. Rocks of Cretaceous age known to contain coal occur in the Styx, Maryborough and Laura Basins in Queensland, the Gippsland Basin in Victoria and both the Queensland and New South Wales portions of the Surat Basin. The coal measures have been deposited in a variety of sedimentary environments and the coals vary widely with regard to thickness, extent, banding characteristics, maceral and ash content. However, they are generally of low rank and most are suitable only for steaming.

Jan 1, 1975

By J A. Wells, K G. Thomas, R F. Dewhirst

"One of the contributing factors to the extreme cost escalation in the first decade of the 21st century was the increase in the amount and cost of engineering work that went into studies and projects. Various reasons for this were identified, including unsatisfactory productivity due to a shortage of experienced/qualified engineers, the increased complexity and infrastructure requirements of many projects due to location, metallurgy that is more challenging and increasing environmental and social requirements. These conditions often led to unsatisfactory project results in terms of cost and schedule blowouts and created a loss of confidence – both internally and externally – in the industry’s ability to complete projects on time and on budget.Technical fundamentals aside, the experience and effectiveness of project teams has had, and continues to have, a major impact on project cost, schedule and ramp-up to nameplate capacity and operating parameters. There are unfortunately too many examples of where project teams have not been as effective as they could or should have been, all to the ultimate detriment of the project.Using the authors’ extensive experience on both owner’s and engineer’s teams, this paper discusses some of the main reasons for suboptimal team, and hence project, performance and offers thoughts on how best to build and maintain project teams. The analysis and conclusions drawn are built around the Tuckman model of group development known as ‘forming-storming-norming-performing’, which was first proposed some 50 years ago. Given the importance of good teamwork to project success, understanding how project teams grow and become efficient and productive is an essential part of good project management that should receive more attention.CITATION:Dewhirst, R F, Thomas, K G and Wells, J A, 2016. Building and maintaining effective project teams, in Proceedings Project Evaluation 2016, pp 38–48 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By M Paakkunainen

Sampling is often the most critical part in process analysis. When the mean of a continuous lot, such as a process stream within a given time interval, is estimated by calculating the mean of several samples, the uncertainty of the estimated mean depends usually on the sampling strategy. Three different strategies can be used: systematic, stratified or random sample selection. The standard deviation of the lot mean is different for these methods so that systematic sampling usually gives the smallest and random sampling the largest standard deviation. Pierre Gy developed a method where the sampling errors of one-dimensional lots for these three strategies can be estimated from a variogram, which is calculated from a variographic experiment, ie from a set of one-dimensional time series measurements with fixed sampling interval. While variogram is an excellent tool for characterising and displaying the variability of autocorrelated processes as function of time, the sampling error estimation from it is quite laborious, however. In this work an alternative method for estimating the sampling errors was developed. The process is divided into strata of equal sizes, varying the length of strata similarly to variographic analysis. For stratified sampling the standard deviation estimates are obtained by analysis of variance and for systematic sampling by fitting a linear regression line to each stratum and calculating the residual variances. By pooling the individual variance estimates the variance estimates that are corrected for autocorrelation are obtained. The new method was tested with simulated and real data sets having periodic, random and/or drift fluctuations. For stationary processes the results agreed well with the results of the GyÆs variographic method. The method can probably be generalised to estimate the sampling variance of higher-dimensional lots.

Jan 1, 2005

Portfolio management tends to separate the functions of Asset Allocation and Stock Selection, so the person responsible for reviewing an expert's report on a company would typically be choosing between companies rather than between a company and cash or bonds. How these choices are made depends on the investment time horizon, philosophy and style. Two styles, momentum investing and value investing are contrasted and the role of valuation methods within the framework of each style is evaluated. Finally, pricing is distinguished from valuation.

Jan 1, 1994

By S Lockie, G Ivanova, J Rolfe

One of the consequences of mining expansion in the Bowen Basin region of Central Queensland in Australia has been a substantial increase in demand for housing, with subsequent impacts on housing and rental markets. Those pressures are reduced to some extent by a proportion of the workforce choosing to live in other centres and commuting to workplace for block periods. The main factors influencing location choice are: housing availability and affordability, basic urban services and lifestyle of the town and the town physical attractiveness such as coastal town. Low costs housing provided by the mining company acts as an attracting factor for some miners to live in the mining town. Recommendations for three short-term and two long-term strategic policy guidelines to address housing situation and location issues are provided.

Jan 1, 2009

By D R. Seaman, R P. Tooher, B A. Seaman

"Several mine scheduling tools exist for use in optimising and scheduling the reserve according to in situ value. These tools generally value the ore on a per block basis according to regressed recovery models based on ore grade and type. It is then the task of the plant metallurgist to ensure that these ore blocks are fed to the plant in a manner that satisfies the prevailing plant constraints. This task is often completed in complex Excel® spreadsheets that are modified over time with factors applied to account for plant modifications or limitations.It is the authors’ experience that this approach is difficult to audit and replicate in a consistent manner. Furthermore, operational decisions, such as primary grind size or autoclave oxidation are made on the metallurgist or managements’ perceived optimum value and does not necessarily represent a cash flow based optimum.Many processing plants contain multiple internal constraints. As ore feed grades and properties change over the life-of-mine (LOM), processing-bottlenecks shift from one unit process to another and different operating strategies need to be adopted to maximise cash generation from the process.This paper presents a unified optimisation approach to scheduling ore based on a circuit mass balance to describe the process plant with individual models for each significant unit operation. The approach allows for optimisation over multiple input variables and the inclusion of linear and non-linear constraints.This optimisation process has been applied to different complex gold operations. The end result is an automated scheduler that selects the optimum blend of ores as well as plant operating conditions that satisfy all internal plant and shutdown constraints while maximising the objective of choice (metal production or cash flow). The models are also valuable for evaluating expansion or debottlenecking opportunities of individual processing units. These models are coded in Matlab® R2016a provided by MathWorks®, and can be deployed to end users in a compiled version with significant savings in time to run different scenarios over the Excel®-based systems.Citation:Seaman, D R, Tooher, R P and Seaman, B A, 2016. Optimisation of Complex Gold Processing Plants with Multiple Unit Operation Constraints - the Newcrest Planning Scheduler, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 191–198 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By M Brockman, M Cowan, A Robeson

"Sunrise Dam Gold Mine (SDGM) is located 820 km from Perth, 220 km from Kalgoorlie—Boulder and 55 km south of Laverton in Western Australia. The SDGM main pit had successfully operated since 1997 and was due to be completed during 2012. An opportunity existed to extract the high-grade crown pillar – 600 kt @ 7 g/t for 135 koz by either open pit or underground methods.The crown pillar was the 60 m (vertically) thick remaining part of the high-grade Cosmo orebody between the top of the paste filled underground mine stopes and the planned base of the final open pit shell.There were two major difficulties being considered when choosing the underground or open pit options:a major wall failure in the upper section of the main pit wall directly above the crown pillar restricting access from the base of the open pit to the top of the crown pillarimpact of a high rainfall event while the crown pillar was being mined from either surface or underground resulting in flooding of the underground mine workings.This paper will discuss the following issues:the process to identify and evaluate the risks in both options using knowledge based modelling software; this technique allowed the evaluation of a complex set of assumptions to arrive at the preferred optionremediation of the Watu failurethe selection of the preferred option and the challenges encountered before, during and after the extraction of the crown pillarthe planning and geotechnical work to ensure the safe extraction of the crown pillarsuccessful outcomes transitioning from open pit operation to a solely underground operation.Citation:Robeson, A, Cowan, M and Brockman, M, 2016. A Case Study on the Assessment, Planning and Extraction of the Crown Pillar at Sunrise Dam Gold Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 115–136 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

Fluid circulation occurs in oceanic crust of all ages, at the seafloor spreading axis, on mid-ocean ridge flanks, in the ocean basins, and in subduction zones. In the first three settings the fluid originates as seawater. At the axis and on the ridge flanks, the circulating seawater produces a major chemical exchange between the oceans and the crust. Based on heat budget constraints, between 10 and 40% of the river flux of Mg can be taken up during high-temperature alteration of the basaltic crust along the mid-ocean ridge axis. Most of the hydrothermal -heat loss, however, occurs on the mid-ocean ridge flanks, where the temperatures are lower and the seawater flux correspondingly larger. The estimated heat loss on the flanks is so large that upwelling must occur over a large fraction (5-30%) of the seafloor less than 65 Ma in age, at seepage velocities on the order of 10 to 100 cm/yr. The circulating seawater need lose less than 1 to 2% of its Mg content in order to solve the Mg mass balance for the oceans. Fluids in subduction zones are commonly less saline than seawater and are rich in methane and other light hydrocarbons. These fluids may originate by dewatering of the downgoing slab. If so, they may close the geochemical cycle of H2O that began with hydration of the basaltic crust at the ridge axis.

Jan 1, 1990

By A Krishnan, C Garcia, I Luna-Berbesi

The discovery and exploration of deposits are progressively shifting to extremely remote regions and greater depths. As a result, exploration costs and the economic risk of a bad investment increase. Current megatrends in the exploration and mining sector indicate a growing demand for the implementation of automation, digitalisation, and machine learning techniques. The implementation of a multi-sensor-based core logging device (DMT, 2024) was done on 400 m of drill cores to optimise interdisciplinary processes in terms of time and quality, by using interlinked and consistent data in real-time, to obtain reliable predictions that support and speed up decision-making. The results are consistent with the laboratory data previously obtained by the mining company, highlighting the benefits of introducing ANCORELOG into their core logging procedures.

Sep 1, 2024

By J Col, D La Rosa, W Valery, A Jankovic

Metso Minerals Process Technology Asia-Pacific and South America (MMPT) has been working with operations around the world to increase their efficiency through æMine-to-MillÆ or Process Integration and Optimisation (PIO) projects. These projects have delivered significant improvements in mine efficiency, mill throughput and reduced operating costs at mines around the world. The MMPT methodology involves rock characterisation, site auditing, data collection, modelling/simulation and implementation of integrated operating and control strategies on site. This results in significant benefits to the operations û for example, 5 to 20 per cent increases in concentrator throughput have been measured. MMPTÆs rock characterisation utilises simple and inexpensive measurements that can be performed by trained site personnel. The advantage of these measurements is that a large amount of data can be collected in a very short timeframe, as the samples do not require shipping to an outside laboratory. Typically, a PIO project starts with a site visit to perform blasting and process audits, collect high quality data including measurements of run-of-mine fragmentation and survey data around all crushing and grinding circuits. These measurements are combined with rock characterisation and the definition of strength and structure domains to model the complete production chain. Site-specific models of the blast fragmentation, crushing, grinding and flotation processes can then be developed. This proven methodology has applications ranging from greenfield projects to long-standing operations with AG/SAG or conventional grinding circuits. Process improvements can be higher mining productivity, higher mill throughput, decreased overall operating costs and higher flotation or leach recovery. This paper discusses a recent application of PIO conducted at a large open pit operation in South America and emphasises the potential that every operation has to ædo more with what they haveÆ.

Jan 1, 2007

By S Khosrowshahi, A Weeks, W J. Shaw

"To provide an indication of expected performance of the mine and mill, feasibility studies should include an assessment of the expected day-to-day variability in process plant feed. Attempts to do this based on conventional resource models will be flawed as such studies fail to consider and account for the in-built smoothing (averaging) of input data.This can lead to one of two situations: an expensive, over-engineered process plant that can cope with every possible situation, or operational strategies that fail to manage the natural variability within the orebody and the impact of day-to-day operational decision-making.In both cases the value of the project diminishes through excessive capital costs or reduced throughput or recovery during operations.Unlike conventional estimation techniques, the geostatistical method of conditional simulation can reproduce the inherent variability of the deposit. Once a valid model has been developed, it is possible to analyse the model using a transfer function that simulates the proposed mining processes and provides a representation of the likely variation of mill feed characteristics at any time scale.The case study demonstrates how the proposed mining strategy would result in mill feed being considerably more variable than expected, resulting in poor recovery, low throughput and potential breaches of environmental conditions. Mitigation measures included budgeting for additional mining equipment to enable greater flexibility during mining and revised stockpiling and crusher feed strategies.Awareness of the benefits of modelling the variability of geometallurgical parameters will increase the use of this approach in producing more realistic financial models of expected mine performance at the design stage.CITATION:Shaw, W J, Khosrowshahi, S and Weeks, A, 2013. Modelling geometallurgical variability - a case study in managing risk, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 247-252 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By M Hilden, K Barbosa, M Yahyaei, C Ndimande, K Runge, V Jokovic

Classification devices provide a link between comminution and flotation. Basically, it determines which particles are diverted back for additional grinding and which ones pass to downstream flotation. Therefore, the classifiers play an important role in the performance of a mineral processing circuit. Hydrocyclones are the most common classifiers used in wet grinding, despite being associated with poor classification efficiency. Hydrocyclones are widely used due to advantages related to low maintenance as well as reduced capital and operating cost. Other classifiers, such as fine screens, have much better classification efficiency compared to hydrocyclones. The major challenge of using screens in an operation, however, is their large footprint and increased maintenance requirements relative to hydrocyclones. Some researchers have demonstrated that switching from hydrocyclones to screens, as the classifier device in a ball milling circuit, resulted in a 20 per cent increase in plant throughput and significant improvements in coarse particle recovery, resulting in a 6 per cent increase in overall flotation recovery. However, it is known that these benefits of improved classification are very much ore specific, ie depending on the ore response. Therefore, there is a need to estimate the benefits of improved classification in pilot scale testing before the plant could consider the potential classifier upgrade. This paper presents the results of two pilot-scale grinding tests where the ore sample was processed using different classifiers: a traditional hydrocyclone and hybrid classification involving the use of a semi-inverted hydrocyclone followed by a screen. The size specific energy and circulating load were used to compare the performance of the grinding circuit. The grinding product was subject to mineral liberation analysis and the impact of classification efficiency on the mineral liberation is discussed in the paper.

Aug 24, 2022

By Taylor R. N

Flow simulations have been performed on the flash-smelting burners currently used at KNS. This paper presents studies of the heat transfer between gas and particles at the burner exit. Gas and particle temperatures, velocity and concentration profiles of the two-phase flow are calculated by the mathematical model. The predicted gas temperatures have been favourably compared against values measured by thermocouples placed near the burners in the flash furnace. The predicted particle temperatures are also reasonable when compared with the measured temperatures.

Jan 1, 1992

Gold mine production in South America was 247.3 tonnes in 1995 up from 156.4 tonnes ten years earlier in 1986. This represents a 58 per cent increase and amounted to 11 per cent of total world gold mine production. The major countries involved in order of production, were: Brazil (67.4 tonnes), Peru (51.5 tonnes),. Chile (48.5 tonnes), Colombia (24.1 tonnes), Venezuela (17.1 tonnes), Bolivia (16.0 tonnes), Ecuador (9.6 tonnes), Guyana (8.8 tonnes), French Guiana (3.3 tonnes) and Argentina (one tonne). The most dramatic increase was reported in Peru where production increased from 10.9 tonnes in 1986 to 51.5 tonnes in 1995, heavily influenced by the production from Minera Yanacocha which began operations in 1993 and produced 17.2 tonnes in 1995.With the reformation of the mining laws and the introduction of investment incentives in all the South American countries in recent years, dozens of major and junior mining companies began flocking into the area in the early-1990s to conduct exploration. A recent study undertaken in Brazil shows that an average of $240 million per year will be expended in this country during the period 1993 - 2010. Twenty-five per cent of this expenditure is expected to be made on gold exploration. Similar figures for Peru are $220 million total per year with 50 per cent for gold; $170 million per year in Argentina with 25 per cent for gold and $120 million ner year in Chile also with 25 Der cent for gold.

Jan 1, 1997

By W Y. Kim, Y B. Kang, Y J. Park

The phase equilibria in the Al2O3–TiOx system were investigated in wide ranges of temperature and oxygen partial pressure: 1300~1600°C and 10-16.6~10-8 atm, respectively. The equilibrium phases and their compositions were identified using X-ray diffraction (XRD) and electron probe microanalysis (EPMA), respectively. Most noticeably, a wide range of pseudobrookite solid solution was found in equilibrium with almost pure alumina. At each temperature, the cationic ratio expressed as RTi = nTi/(nAl + nTi)) of the pseudobrookite solid solution showed a noteworthy dependency on the oxygen partial pressure. This resulted in the formation of a broad range of pseudobrookite solid solutions, ranging from Al2TiO5 (RTi = 1/3) to Ti3O5 (RTi = 1.0). Complete miscibility within the pseudobrookite solid solution was observed at 1600°C, with only a minor miscibility gap becoming evident below 1500°C. Based on the results obtained in the present study, the behaviours of Al2TiO5 pseudobrookite have implications in two key domains: (1) understanding changes in the physical properties of the materials, and (2) elucidating the evolution of Al–Ti complex oxide inclusions in liquid steel which can deteriorate the steel cleanliness.

Aug 21, 2024

By J Eberhard, C Paton, J Bennett, C Baillie, A Melland, J F. Clewett, T Newsome

A central aim of rehabilitation is to ensure that disturbed land is returned to a post-mine condition that is safe, stable and self-sustaining. This paper describes initial results from a grazing trial at the New Acland open-cut coal mine in southern Queensland (-27.27 lat, 151.72 long) that aims to assess the sustainability and viability of cattle production from rehabilitated mined land compared to production from surrounding unmined lands (Newsome 2014). The grazing trial was established in 2013 by the Acland Pastoral Company, a subsidiary of New Hope Coal, on lands previously used for dairying, beef and crops before open cut coal mining of the Walloon coal measures began in 2002. The area has a mean annual rainfall of 640 mm. Local soils, typically dermosols and vertosols derived from sandstones or overlying basalt flows, are suited to grazing but are marginal for cropping.CITATION:Clewett, J F, Newsome, T, Paton, C, Bennett, J, Melland, A, Eberhard, J and Baillie, C, 2018. Sustainable production from rehabilitated coal mine pastures in southern Queensland’s Brigalow Region – Acland grazing trial results, in Proceedings Life-of-Mine 2018, pp 35–37 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

In general the iron ore industry has been slow to adopt the Whittle Pit optimising software in the evaluation of iron ore deposits. The reasons for this are two-fold:the iron ore industry has developed techniques, usually bespoke software residing in the corporate offices of the respective iron ore companies, to establish their final pit limits; and the fact that the Whittle software doesnÆt easily lend itself to estimating a sales product of constant quality without maximising grade (metal content). The Whittle software is based on the work done by Lerch and Grossman (in the early 1970s), which proposed that graph theory be used to establish an optimal surface that maximises the revenue from a deposit. The maximised surface created in the pit optimiser is translated into a proposed optimal final pit shape that can be used by the mine design engineers as a target outline to lay out the final practical pit. By treating a geological and ore resources model that was created for an iron ore deposit as a subset of the recoverable resources estimation (RRE) type of geological models, the evaluation of an iron ore deposit and establishing the final pit is greatly simplified in the Whittle 4-X optimiser. Instead of trying to optimise the iron content of the deposit, the emphasis swings to maximising the extraction of a finished and saleable iron ore product. This is achieved by treating the finished saleable iron ore as an element in the multi-element Whittle optimiser. The quality of the finished sales product is represented, and the material that cannot be used in the blended product is also shown. Proposals for enhancing the functionality in the Whittle 4-X optimiser to make the evaluation of iron (and coal) deposits easier includes the creation of a new reporting function that will allow the user to specify which field(s) can be used as the divisor(s) for the reporting of the element grades in the model.

Jan 1, 2007