Search Documents

By Kadoya H, Kondo Y

The Harima works were established in 1964 and started operation in 1966. The initial capacity was 3500 t/month of zinc and 1500 t/month of lead. Until 1990 a lot of improvements had been made and the capacity had increased 6600 t/month of zinc and 2200 t/month of lead without enlarging the furnace size. During the ten weeks campaign shut-down at the end of 1990, many modifications were carried out including the enlargement of the furnace shaft area. By these changes, the capacity has gone up to 7500 t/month of zinc and 2500 t/month of lead. In the sinter plant, the amount of SO2 rich gas supplied to the acid plant was raised to 50 000 Nm3/h from 43 500 Nm3/h. An electrostatic precipitator was adopted instead of a venturi scrubber to clean the rich gas. Oxygen enrichment has been continuously operated since August 1991, because the furnace capacity is more than the rate of sinter production. Utilisation of the sinter plant is high being as much as 97 per cent and the sulphur burning rate has been increased. In 1990 the furnace was replaced except the hearth. The shaft area was enlarged to 19.4 m2 from 15.3 m2. The target blast was designed to be more than 36 000 Nm3/h. Tuyere layout was changed to prevent slag breakouts. Due to these modifications shaft condition has been very good. Automatic launder jacket cleaners were installed to increase the lead cooling efficiency. Many other improvements and developments were also made. Coke powder injection from the tuyeres has been successfully operated since April 1987.

Jan 1, 1993

By S C. Dominy

The Bendigo Goldfield is located in the state of Victoria, Australia, and is one of a number of quartz-reef fields that make up the greater Central Victorian Goldfield. At Bendigo gold particles are characterised by their very coarse nature, ranging from below 100 to over 10 000 ¦m in size. Some 60 per cent of the gold occurs in particles greater than 1000 ¦m in size. This characteristic ensures that the mineralisation is very challenging to both sample and evaluate. Diamond drilling provides a measure of geological structure, but is a poor measure of in situ grade, understating it by up to 75 per cent. Drilling combined with on-reef development, bulk sampling and geological interpretation has been used to define Indicated Mineral Resources. For grade control, a balance had to be sought between sample representivity, cost, turn around time and practicality. Sampling of extreme nugget effect deposits generally requires the use of bulk sampling in order to be representative. However, the cost and turn around time is significant. As a result, a 50 kg micro-bulk sampling system has been introduced that attempts to overcome these problems by providing a fast, practical method that can discriminate between ore and waste. As the mine passes into production, grade control will increasingly become dependent upon geological data collection and interpretation.

Jan 1, 2005

By K J. Lownie, T Rafferty

The in situ testing of mine ventilation fan systems has been a contentious issue for many years. Site testing was generally undertaken by adapting standards that were developed for the laboratory testing of fans using standardised airways. The deficiencies inherent in this practice have been widely recognised by informed practitioners, and this led to the first stand-alone document specifically intended for the in situ testing of large fans (ISO 5802:2001 Industrial fans - Performance testing in situ).This paper describes the structure of the International Standards organisation and the processes that are followed in the course of preparing such a standard.The application of ISO 5802:2001 is briefly outlined together with how test data is assessed for compliance with the suppliers guarantee. This paper must be read in conjunction with ISO 5801:2007, ISO 5802:2001 and ISO 13348:2007.CITATION:Lownie, K J and Rafferty, T, 2013. A review of ISO 5802:2001 industrial fans - performance testing i n situ, in Proceedings The Australian Mine Ventilation Conference , pp 149-154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By J R. Taylor, J A. Muchan, S M. Pape, B S. Davis

Acid and metalliferous drainage (AMD) is routinely derived from waste rock, tailings, pit wall rock, underground mine voids, heap leach pads, ore stockpiles, concentrate stockpiles and even slag piles. In many jurisdictions, there is an assumption that tailings materials represent the highest AMD risk. This is likely due to their highly sulfidic and ultra-fine grained nature, and the fact that they occur in large tonnage, partially unsaturated deposits. These characteristics are not unreasonably associated with reactive and therefore highly polluting mine waste materials. Interestingly, however, the high sulfide content and highly reactive nature of tailings achieves the rapid consumption of oxygen in tailings pore spaces. This oxygen depletion can limit or halt sulfide oxidation throughout much of the tailings pile. Oxygen can only be resupplied to the tailings via atmospheric exchange at the air-tailings interface. The grain size of most tailings materials limits this resupply to a diffusion related process that only affects the uppermost 100–2000 mm. Hence sulfide oxidation in tailings can be inherently self-limiting. Unfortunately, the same cannot be concluded for waste rock materials.Using a unique site assessment strategy that focuses on quantifying acidity fluxes from various domains at a mine site, it has become increasingly evident that sulfidic waste rock produces the majority (typically 60–80 per cent) of the soluble acid and metalliferous pollution at most active and decommissioned sulfide-bearing mine sites. Whether sulfidic waste rock is disposed in engineered above ground facilities, backfilled into pits or even underground voids, it remains the primary source of pollutants for decades to centuries.Conventional end-dumping waste rock practices result in angle-of-repose pathways for air and water, and these internal fabrics exacerbate sulfide oxidation (ie pollution generation) and discharge from waste rock materials. The primary aim of many cover systems is to retard the access of air and water to these conduits. Recent thinking is that more emphasis needs to be directed at strategic waste rock pile construction practices, and less reliance placed on thin soil cover systems to prevent AMD.Waste rock pile construction approaches that minimise porosity and permeability but raise the retained moisture content and enhance water residence times have the potential to lower sulfide oxidation rates and thereby improve water quality outcomes. For example, innovative base-up, layered and compacted (BULC) waste rock piles have the potential to avoid or minimise the generation of AMD, supersede the need for treatment and facilitate successful closure and relinquishment across the mining sector (Figure 1).CITATION:Taylor, J R, Pape, S M, Davis, B S and Muchan, J A, 2016. Waste rock pile construction to lower closure and relinquishment costs, in Proceedings Life-of-Mine 2016 Conference, pp 97–99 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Wilkins C

The Browns Creek deposit is located 8 kin west of Blayney and 220 km west of Sydney (Figure 1), at lat 33¦32'S, long 149¦10'E on the Bathurst (SI 55-8) 1:250 000 scale map sheet. The total measured, indicated and inferred resource at 30 June 1997 was 1.29 Mt at 6.39 g/t gold and 0.45 per cent copper. During the 1996 - 97 year 263 557 t of ore at 6.30 g/t gold and 0.48 per cent copper was treated, to produce 47 496 oz of gold, and 1 169 t of contained copper in concentrate. As the result of an increase in the resources and reserves, because of underground exploration drilling and accelerated mine development, 1997 production at Browns Creek is predicted to expand from 240 000 to 390 000 tpa, to yield more than 70 000 oz of gold per year.

Jan 1, 1997

By N Taylor, P Hewitt

The Northern Beaches Storage Project (NBSP) is part of Sydney Water’s SewerFix™ Program to improve the wastewater system and protect public health and the environment. It was built by the SewerFix Wet Weather Alliance (the Alliance), a partnership between Sydney Water, RPS, MWH, Parsons Brinckerhoff and United Group Infrastructure.The project temporarily stores excess wastewater diverted from the Narrabeen Submain during wet weather. The project considered a below-ground storage facility, which involved constructing a deep tunnel from Brookvale to Fairlight, connecting into the Northside Storage Tunnel and a storage tank, which was subsequently adopted and constructed.The storage tank scheme included a pumping station and inlet and outlet pipes installed by microtunnelling. The storage tank site is in the Brookvale industrial area situated in an area of deep marine sediments overlying Hawkesbury Sandstone at about 30?m below ground. Microtunnelling for the inlet pipe was conducted from a 12?m deep jacking shaft. The jacking shaft and 14?m deep pumping station excavations were carried out from within secant pile earth retaining structures adjacent to existing buildings.Construction activities had the potential to cause settlement of the adjacent buildings. During excavation and microtunnelling the water ingress, adjacent groundwater level and settlement of the adjacent buildings were monitored. The monitoring data was assessed against an action plan, which modified construction activities as required to minimise the risk of damage to buildings from settlements caused by lowering of the groundwater table outside the excavations. The secant pile construction, excavation, microtunnelling and pumping station construction proceeded without incident or damage to adjacent buildings.This paper highlights that tunnel/underground options should be considered during options development, describes the original storage tunnel scheme and presents details of the successful microtunnelling and deep shaft construction adopted on the NBSP.CITATION:Taylor, N and Hewitt, P, 2014. Tunnelling on Northern Beaches Storage Project, Sydney, to improve water quality, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 451–458 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Stone I

Tahmoor Mine is located in the southern Sydney Basin 80km south-west of Sydney and produces 1.2 MT of Bulli Coal annually. Bord and pillar methods used to date will be supplemented by a longwall system. Difficult roof conditions have been experienced since mining began in 1979. A dominantly horizontal stressfield promotes shear failure in the thinly interbedded roof sequence of shales, laminites, siltstones and fine sandstones. General roof conditions and failure characteristics are related to the angle between the roadway direction and the principal horizontal stress direction. The apparent stressfield changes direction, magnitude and the ratio of principal horizontal components across the mine workings in response to both in situ and mining induced causes. Initial roof support of 5 x 2.1 m bolts per W-strap at in intervals, with mesh, was upgraded to include RSJ's in order to support areas of failed roof. This support system was inefficient and costly. A third system of support emphasizes roof reinforcement with full resin encapsulation of 2.1 m bolts in W-straps. The number of bolts per strap (6-8), extra butterfly straps and bolts, and W-strap spacing is determined for each area by expected roof and stress conditions. Intersections are pre-bolted and ribs are supported in some areas. Pillar dimensions, order of drivage and roadway width have each been altered to improve roof control. The intensity of roof deformation at the face varies from panel to panel and causes development rates to decrease to 30% of the maximum. 1. Manager, Tahmoor Mine, Tahmoor, N.S.W. 2. Senior Geologist, BP Coal, Picton, N.S.W. Roof conditions in each area of the mine are characterised and then projected to future development areas based on the relationship between stressfield orientation, relative roadway direction and face conditions. Planning information available includes expected development rates, roof support requirements and areas of changing conditions. Future improvements of strata control involve defining support design parameters for the range of mine conditions already seen at Tahmoor.

Jan 1, 1986

By D Felipe, G J. Harbort

In the past 40 years substantial changes have occurred in flotation machines. This has included increases in mechanical cell size to 630 m3 , significant changes to flotation column aeration design and widespread use of the Jameson cell and other pneumatic flotation cells. Over the corresponding period there has been increased used of machine characterisation measurements to benchmark and optimise flotation circuit performance. JKTech maintains a database of industrial flotation machine characterisation measurements. The database contains over 4000 entries and includes gas dispersion measurements, such as bubble size, gas hold-up and superficial gas velocity, cell dimensions and impeller tip speeds. Data comes from numerous operating sites and commodity groups, including gold, copper, molybdenum, nickel, palladium, lead-zinc, platinum, silica, phosphate, coal and iron ore. Flotation duties registered include flash flotation, preflotation, roughing, scavenging and cleaner circuits. Measurements have been conducted on a wide range of flotation machines from different manufacturers. This includes forced air machines, such as Outotec and Dorr Oliver, and self-aerated machines, such as Denver and Wemco. The database also includes substantial flotation column entries, such as the Microcel, Eriez/CMT Slamjet and Jameson cell. This paper describes the flotation machine characterisation database and discusses the variation between different types of industrial flotation machines, in operating production circuits.

Aug 24, 2022

By D S. Perera, P Wal, D C. Southam, J L. Lowe

The Cooperative Research Centre for Sustainable Resource Processing (CSRP) is undertaking a large research project involving partners from industry, universities and government, which aims to develop the necessary chemical and structural understanding of geopolymer materials made from waste products for them to be used to capture a significant market share of the concrete business for a given industrial region. We are investigating the suitability of a range of soluble silica-bearing waste streams for use as geopolymer concrete feedstocks. In order to utilise a variety of waste streams, either singly or blended, an understanding of the role of secondary metal ions (Fe, Ca, Mg, Ti, etc) in the geopolymerisation process is essential. A range of experimental and analytical techniques is therefore being used to better understand the structure-chemistry-property relationships of geopolymers. Currently, we are investigating geopolymers made from a variety of waste streams (fly ash, kaolinite, red mud, etc) available in the Kwinana Industrial Region, Western Australia. This paper will detail how the basic scientific research underpinning the project is vital if waste streams of varying composition are to be successfully used in a commercial concrete product and the regional synergies required to develop geopolymers from waste streams.

Jan 1, 2006

By C S. Kelsey, J R. Kelly

Australia is presently enjoying the fruits of a booming iron ore market. Expectations are that market strength will be supported in the short to medium term by increasing feedstock demands from steel mills, as world economies rebuild post-Covid-19. However, as cost and environmental pressures increase the longer-term market outlook will be dominated by product quality. The ‘flight to quality’ will place increasing demands on direct shipping ore miners as they compete to maintain their standing in the iron ore marketplace. China will progressively disengage from its dependence on Australian imports, leaving miners under increasing pressure to boost product quality and diversify outlets globally. Australia has vast deposits of low-grade magnetite ores located mainly in remote and arid regions of the continent. This paper proposes a dry grinding and magnetic separation process to produce premium concentrate grades from the low-grade ores, to assist in meeting future product quality demands. The premium grade concentrates could be either blended with lower quality direct shipping ores or marketed separately. The proposed dry concentration process involves the pairing of Vertical Roller Milling (VRM), a mature technology widely used in the cement industry, and Planar Magnetic Separation (PMS), a new methodology, which has been developed to the threshold of commercialisation by the private Australian company Cyclomag P/L. Two laboratory prototype planar magnetic separators with field strengths of 1800 gauss and 6000 gauss have been built and tested on a range of magnetite ore types over the past three years. In each case, following grinding to liberation sizes, a combination of roughing and cleaning operations has produced pellet grade concentrates. Vertical roller milling has competed successfully with conventional media milling in grinding cement clinker, limestone and blast furnace slags. A key advantage of dry VRM/PMS processing is its potential adaptability to stepwise modular development, which can minimise initial capital investment, while generating early revenue streams to cope with unpredictable market volatility.

Nov 8, 2021

By Warren L. J

The recovery of phosphate minerals from the Mt Weld deposit by froth flotation has been studied by many researchers. Most of the flotation experiments were carried out with a tall oil fatty acid as collector and sodium silicate as dispersant and gangue depressant at pH about 10. Several rougher stages and cleaner stages and, sometimes, a desliming stage were included. The major difficulty was to reduce the Fe2O3 impurities in the concentrate to the required level. We used QEM*SEM (Quantitative Evaluation of Materials by Scanning Electron Microscopy) to provide a comprehensive and accurate mineralogical analysis of the flotation products. The analysis indicated that the Fe2O3 impurities were mainly recovered in the second concentrate, owing partly to the incomplete depression of the liberated iron oxides by the sodium silicate and partly to composite particles containing iron oxides. The selective depressing action of sodium silicate was improved by adjusting the variables such as the modulus (SiO2/Na2O), pH and time of standing of the stock sodium silicate solutions or by adding some polyvalent metal salts into sodium silicate solution. The flotation process was optimised to produce a phosphate concentrate with the required grade and recovery (38.6 per cent P2O5, 2.67 per cent Fe2O3, 13.7 for P2O5/(Fe2O3 + A1203), at P2O5 recovery of 81.5 per cent). The possibility of recovering the rare-earth phosphate, monazite, from the Mt Weld deposit by flotation was also studied.

Jan 1, 1991

By W Russell, P Wighton, J Franke

Recent advances in ruggedised industrial control system technology and architecture in combination with latest technologies in the fast-evolving 3D LiDAR sensor sector becoming available have enabled the implementation of sophisticated automation algorithms for mining equipment such as bucket wheel reclaimers, as published by the authors in the peer reviewed AusIMM 2019 Iron Ore conference proceedings. This paper provides an overview of a second use case for such automation technology in bulk material ports integral to iron ore operations. The real-time 3D machine-vision based port automation system described in this paper was originally developed for the BHP-Mitsubishi Alliance’s (BMA) Hay Point port. The system has seen deployment at other major mining and general ports in Australia, such as at Dalrymple Bay Terminal (DBT) (shown in Figure 1) managed by Dalrymple Bay Infrastructure Management (DBIM), Hay Point, Queensland. It has the following use cases:

Nov 8, 2021

The paper highlights the conceptual developments in rock mechanics applied to quantify the effect of bolts in the stabilization of joints and yielding soft rocks. NOTATION Aa = stress change after excavation Eä EE, Eä = moduli of intact rock, single joint and jointed rock Eb = elastic modulus of the bolt k, = normal stiffness of joint Ab = cross section area of the bolt A, = area of influence per bolt ab = axial bolt stress e, = axial strain of the bolt eä e,, ej, = strains of intact rock, joint and jointed rock Ai = area of the joint ,r+ = shearing resistance of the bolt (at the joint) a = normal stress at the joint plane aäa3 = major and minor principal stresses c;, 4i; = cohesion and friction angle of the joint 0 = angle between the bolt and the joint a = inclination of the joint to the vertical axis P = bolt density parameter u, = convergence of unsupported tunnel section u, = convergence of bolted tunnel

Jan 1, 1992

By Kobe HW, Balance PF, Black PM, Sporli KB, Smith IEM, Locke CA

The Hauraki Goldfield consists of a large number of volcanic-associated epithermal gold deposits within the Coromandel Volcanic Zone (CVZ), North Island , New Zealand; it is the most accessible and most studied of the Southwest Pacific gold regions. The deposits occur generally as steeply dipping quartz veins and breccia sheets in faults and fractures.From a tectonic perspective, the CVZ is generally considered a Neogene convergent volcanic arc constructed under an extensional tectonic regime; the common tectonic setting for epithermal mineralisation. The gold deposits are mostly hosted in subaerial andesitic arc-type volcanic rocks. Temporally, however, mineralisation is associated with rhyolitic rocks of a bimodal volcanic suite that may represent a back-arc environment. Rifting and calderas may be important components of the latter regime, but this is not yet clear; the general structural framework controlling the location of CVZ gold deposits remains poorly understood. Geophysics, particularly aeromagnetics, has a role in mapping regional fault patterns in the CVZ

Jan 1, 1990

By C E. Loayza, R M. Pinto, J G. G=mez

The Yanacocha District is located 20 km north of the city of Cajamarca, in the Northern Andean Orogenic belt of northern Peru.Gold production may have occurred as early as Incan times (Paverd, 2000), but modern exploration that began in the 1960s targeted only copper and silver. Newmont Mining Corporation, BRGM and Compa±fa de Minas Buenaventura began exploring for gold in 1983, with Newmont as operator.Initial drilling took place in 1985. By 1992 a reserve of 1.28 million ounces was reported (Teal et al, 2002).Production began at the Carachugo deposit in 1993.Current reserves are 31.7 million ounces at $US 325 per ounce at a grade of 1.03 ppm (Newmont Annual Report, 2003).The operating company, Mineral Yanacocha SRL (Newmont 51 per cent, Buenaventura 44 per cent and International Finance Corporation five per cent) produced 2.85 million ounces in 2003, making Yanacocha one of the largest gold mining operations in the world. The district is made up of a series of epithermal, high sulfidation style gold deposits and one gold-rich gravel deposit (La Quinua), aligned in a NE trend.La Quinua is not discussed in detail in this paper. The bedrock deposits are hosted in a Miocene volcanic package, the Yanacocha Volcanic Complex that also trends NE.Re gional NW striking Andean faults intersect the NE striking Trans-Andean Chicama-Yanacocha structural corridor (Turner, 1997), localising the district mineralisation. These two structural orientations dominate the district, controlling breccia and intrusion locations, and gold mineralisation. Discontinuous EW oriented fracture zones are interpreted as extensional and locally are important in controlling gold mineralisation.

Jan 1, 2004

By Y K. Leong

Occasionally additives are used in the wet processing of iron ore tailings and slurries, for examples, in the thickening of tailings with flocculant to recover process water, and in the smooth pumping of concentrated slurries. They can mitigate slurry behavioural issues that could significantly affect the plant operation and production. The nature of iron ore business requiring the plant to have a high throughput to be economical, large amounts of slurries are therefore processed every day. The quantity of additives needed will correspondingly be large and so are the associated costs. This could have a significant impact on the plant profitability. If additives are used they must be very costeffective. NaOH is among the lowest cost chemicals available, at ~US$400 per ton. In this paper we will look at use of composite additives involving phosphate compounds with NaOH added to reduce the cost, for the control of iron ore slurries rheology. The NaOH worked synergistically with the phosphate compounds. The effectiveness of these composite additives in viscosity reduction can be neutralised by another cheap additive such as lime or a Ca(II)-based salt turning the slurries back to being a paste. Tailings paste is an ideal material for safe storage in the dam. These composite additives can also be used to facilitate the recovery of iron ore at commercial grade from tailings (Leong, 2020a, 2021a).

Sep 18, 2023

By A M. L Smith, W E. Dubbin, K A. Hudson-Edwards

Jarosites (KFe3(SO4)2(OH)6) are examples of minerals that are highly effective scavengers of toxic elements, and are abundant in acid rock drainage systems, acid sulfate soils, metallurgical wastes and other contaminated sites. The K, Fe and S sites can be filled by toxic elements such as Cd, Cu and Zn, but the mechanisms of this incorporation are not well understood.We have used atomistic simulation methods to model the jarosite (102) surface and its interactions with Cd, Zn and Cu, in order to understand the mechanisms by which these potentially toxic elements are incorporated into the K-jarosite structure. Our results suggest that incorporation via a defect complex consisting of an impurity cation at the K site charge balanced by a K vacancy stabilises the (102) surface in the order Cu>Zn>Cd.

Jan 1, 2008

By H J. J Boshoff

Pit lakes, as a final void after completing open cut mining, are in most cases unavoidable. Initial mine designs and approvals require consideration and assessment of closure objectives, legislation and stakeholder acceptance to ensure suitable understanding of the closure liability. Mining companies undertake studies and engineering during the planning, operational and closure stages of mining to identify closure options for the final voids, which would be sustainable. Without adequate planning prior to and during the life of the mine, options during the closure stage become limited resulting in costly closure works or long-term liabilities. Engineering consultants provide a specialist service in the assessment of long-term pit lake water levels and characteristics. Ongoing advances in mining methodology and technology, coupled with improved data collection and data management aid in a better understanding of the complexities in estimating long-term pit lake water levels and characteristics. Closure objectives developed during the planning stage sets the requirements for long-term pit lake water levels, which could require maintaining a water level and pit water or discharge water quality. A variety of approaches could be used to assess these closure scenarios each requiring specific data and methodologies. Typically, limited data is available during the planning stage, which results in assumptions based on past experience and relevant case studies. Closure assessments are revisited during the life of mine and leading up to the closure stage, during which additional site-specific data is available improving the accuracy of the assessments.CITATION:Boshoff, H J J, 2018. Assessment of approaches, data requirements and methodologies for estimating long-term pit lake water levels, in Proceedings Life-of-Mine 2018, pp 28–31 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By Boyd G. L

Stress measurement is at the core of most stability design analyses. It is demonstrated that contrary to accepted practice, it is the field measurement, and not the calculated prediction, of stress that requires most examination and review. Since it is not really possible to quantify rockmass properties, the stiffness values used in reduction of stress measurements and in subsequent design analyses (either empirical or numerical modelling) must consider an appropriate range of values.

Jan 1, 1995

By Kneisley RO

This paper presents a brief overview of current bump mechanics theories and pillar design methodologies, and relates these concepts to experiences at two mines located in a north- central Utah coalfield where different pillar designs were used to control mountain bumps. Experiences gained at the first mine demonstrated the successful implementation of a two-entry, 9.8 m (32 ft)-wide, yield-pillar design. A U.S. Bureau of Mines field study quantified the timing of chain pillar yielding and resulting load transfer from the gateroad. In-mine pillar response, although apparently sensitive to site-specific conditions, compared favorably to estimates derived using two yield- pillar design methods. A second study conducted at another mine located in the same district, but subjected to different geologic conditions, documents the unsuccessful attempts to employ progressively narrower three-entry pillar designs based on successes achieved at the first mine site. This second mine never achieved a true yield-pillar design. Use of pillar widths ranging between 9.1 m (30 ft) and 27.4 m (90 ft) always resulted in violent bumps in the tailgate pillars. The pillars were either too large to yield, or too small to support peak operational loads. Hypothetical gateroad systems were evaluated using both analytical and empirical approaches for configurations comprised of two rows of conventional pillars, and systems incorporating both yield and abutment pillars. Analysis concluded that yield pillars less than 6.1 m (20 ft) wide and abutment pillars ranging between 30.5 m (100 ft) and 39.6 m (130 ft) square would be required to achieve a stable gateroad design. However, results of a field study conducted on a two-entry, 36.6 m (120 ft)- wide abutment pillar concluded that abutment pressures from the first panel overrode the pillar, and that a still larger pillar may be required to preclude bumps in the tailgate during second panel mining. Without the benefit of a demonstrated in-mine success, it is not clear which design would ensure elimination of gateroad bumps.

Jan 1, 1992