Search Documents

By C Jenkins, J Jasper, Y Suryaputradinata, S Lozyk, M J. Hartmann

The primary objective of mining companies is to function as a profitable business by delivering products that fit customer requirements in a safe and sustainable manner. Optimum resource utilisation is a critical focus area to achieve this objective, and the long-term sustainable business performance of a mining company is determined by the extent to which this is achieved. Technology improvements and/or new technology development could improve resource utilisation. However, adding new projects to a Brownfield operation carries risk. Overall project schedules, tie-in schedules and safety risks normally receive adequate attention, but the introduction and integration of new technology to a Brownfield site also carries the significant risk of failure to achieve design performance (quality or throughput). This risk must be addressed via rigorous design phase risk assessments and piloting. Post commissioning, the effective metallurgical integration of any new technology/circuit/process plant into an existing process plant calls for critical assessment, through circuit performance testing, and optimisation to ensure alignment with design criteria. In addition, this approach provides clear focus areas for further optimisation of the new plant and additional opportunity for overall plant optimisation. Roy Hill recently navigated this process successfully, and this paper provides feedback on the journey that led to improved resource utilisation.

Nov 8, 2021

By Potter DJ, Firkin GR

The Imperial Smelting Furnace operated by Sulphide Corporation Pty. Limited at its Cockle Creek zinc-lead smelter was recently equipped with tuyeres angled at 25 degrees instead of the usual 10 degrees. This change was prompted by the results of model studies undertaken by tha Research Department of Imperial Smelting Processes Limited, at Avonmouth in the United Kingdom, and by the favourable results of operating trials on the Cockle Creek furnace using bent-tip tuyeres to simulate 25 degree inclination. The use of 25 degree angle tuyeres has made it possible to operate with lower zinc values in discard slag and has improved hearth stability over a wider range of sinter quality and composition.

Jan 1, 1981

By F Djukic, T Fisher, G Irving

Questionnaires were sent to 12 underground metalliferous mines in Queensland to enquire how these mines control diesel emissions from mobile diesel engines used underground. Where responses or controls were absent, discussion has been provided. A significant finding concerns secondary ventilation design rates. Some mines were designing ventilation rates to meet the superseded Mines Regulation Act of 1989 which required 0.04 m3/s/kW. The current Queensland Mining and Quarrying Safety and Health Regulation (2001) is risk based. In line with other jurisdictions, including New South Wales (NSW) and most Provinces in Canada, a minimum ventilation rate of 0.06 m3/s/kW is acceptable. However, this design ventilation rate will vary in practice depending on the diesel engines and controls. Dedicated ventilation engineers and technicians should be appointed to evaluate the effectiveness of the ventilation system. Personal exposure monitoring is required to confirm that exposure standards are not being exceeded. The primary control practice should be to reduce the emission at source. This can be ensured by purchasing low emission (Tier 2, Tier 3) equipment. In addition, the use of ultra low sulfur fuel (et al, 2002). Diesel fuel with a low aromatic content such as Eromanga diesel fuel will also mean employees are exposed to lower levels of poly-cyclic aromatic hydrocarbons. These controls should be carried out in parallel with good maintenance practices. Preventative maintenance should be programmed and emissions be routinely tested, including both gaseous and particulate pollutants and compared against defined criteria. According to McGinn, 2002, there are a number of fundamental tools necessary to carry out preventative maintenance. These are outlined in maintenance guidelines and best practices for diesel engines in underground mining produced for the Diesel Emissions Evaluation Program (DEEP). An effective diesel emission management system needs to be fully integrated within the Safety and Health Management System. These requirements are further discussed in this paper.

Jan 1, 2007

During 2009 the technical services staff at Barrick Gold Corporation's Australian Business Unit conducted a review of their five underground mines that utilise pastefill as the backfill component for these operations. Of the five mines reviewed three use dry tailings and two use wet tailings plants. The primary aim for these reviews was to determine whether pastefill was the right option to be used, and if not, what where the alternatives. The reviews undertaken focus on several areas including, paste plant operation, reticulation and barricade techniques, the geotechnical requirements for pastefill in regards to the current mining methods, the consideration of alternative methods, capital and operating cost histories compared to initial estimates, and a cost benefit analysis of pastefill against other mining methods. The main benefits from the use of pastefill is increasing the extraction of the resource, reducing or eliminating the need to leave pillars. In some mines the use of pastefill is geotechnically driven, to manage high stress environments or mining induced seismicity. A third benefit of using pastefill in some circumstances is that it reduces dilution, however it is considered that this is not a valid argument for most of the mines reviewed. At two mines no alternative to pastefill was determined, whilst differing extraction and filling strategies were potentially identified at the other three mines. The reviews developed cost benefit curves for those sites that had alternative mining methods to assist in determining whether pastefill is the right option to use for any particular stope. At the grades typically mined in each operation, pastefill was the preferred option to use. In all mines, pastefill was determined to be the best option at this time.

Nov 25, 2010

By Kristiansen J

A series of laboratory blasting and ball mill grinding tests have been done on four different types of hard and competent rocks. The results show that exposing these rock types to a higher level of explosive energy will enhance their grindability. True blasting optimisation should therefore look at the whole comminution process from solid rock to a marketable product.

Jan 1, 1995

Problems associated with gas management become more significant as exploitation of coal reserves in the Bowen Basin in Australia becomes deeper. At Oaky North mine, relocation of production from one area of the mine to another with a higher gas content required the use of pre-drainage, post drainage and inertisation techniques to enable production activities to continue largely uninterrupted. Innovative surface to inseam drilling techniques were developed for pre-drainage of reserves close to mine workings and have proven to be largely successful. The gas management techniques adopted and specific experience gained are discussed in this paper.

Jan 1, 2005

By D Luppnow, H Rourke

Recent disasters such as the failure of the Mount Polley tailings embankment remind us of the risks that tailings facilities pose. It is widely recognised that dam-break assessments are a vital tool in identifying the consequences of the failure of a facility, which in turn can be used to develop emergency action plans. A typical assessment includes an estimation of breach parameters and outflow volume, followed by the preparation of an inundation map to illustrate potential flow extents and downstream impacts. This paper focuses on the estimation of outflow volumes, which is an area that the authors feel can be improved. Presently, many types of analyses assume that the volume of tailings released is only a function of the storage volume and dam height. After a review of several documented tailings failures, it has been found that the extent and depth of the supernatant pond needs to be considered as it is just as important, if not more so, as the storage volume and dam height. Tailings facilities with excess water storage have a higher risk of failure as they are more susceptible to overtopping, piping and liquefaction failures. In addition, they pose greater failure consequences as the saturated conditions will lead to more material being mobilised.This paper has reviewed available information on a number of tailings dam failures and proposes an alternative estimation of potential tailings release volumes as a function of supernatant water stored on the facility for use in dam-break analyses. In a broader sense, the paper seeks to shift the current risk paradigm from tailings dam heights to volumes of water stored and provides a basis for continuing research and discussion.CITATION:Rourke, H and Luppnow, D, 2015. The risks of excess water on tailings facilities and its application to dam-break studies, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 225–230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By S J. Loach

F-Series reconciliations are formal comparisons of estimates and measurements of ore quantity and quality made at pre-determined points along the mining value chain. F1 is the ratio of ‘Depleted Grade Control Ore/Depleted Long-term Model Ore’ and validates the models upon which Resource and Reserve statements are based. F2 is the ratio of ‘Produced Tonnes and Grade/Depleted Grade Control Ore (-) Changes in Pre-Crusher Stockpiles’ and validates that the ore tonnes and grade delineated in the pit are being accurately extracted and correctly delivered to the processing plant. These factors provide important corporate assurance for a mining company by providing quantitative feedback on model-predicted tonnes and block grade estimates. Since 2009, BHPs Western Australian Iron Ore F-Series reconciliations have been calculated in a single, centralised sequel-server database. This software routinely collates data regarding mineral resource block model depletions, grade control model depletions, pre-crusher stockpile inventories and production tonnes and grade measurements and then calculates F-Series factors for both tonnes and product quality. This paper will present case studies where reconciliation factors were used to identify improvement opportunities leading to projects that improved our models and subsequent forecasts of production tonnes and quality. In addition, it will show how reconciliation factors are tools that monitor control during periods of rapid change and provide feedback on the effectiveness of improvement projects.

Sep 18, 2023

By Hagen G, Uhlig H

In the Federal Republic of Germany the thermal environment in underground coal mines has deteriorated progressively over the past years. The number and capacity of refrigeration plants have increased correspondingly. In recent years high capacity spray coolers have been used in addition to conventional cooling coils.

Jan 1, 1988

By Ovchinnikov YN, Novikov VS, Spirin NA, Babushkin NM, Mysik AF, Shcherbatskii VB, Kukarkin AS

Laboratory investigations were carried out to determine the resistance coefficient of the flow through beds irrigated with wetting and non-wetting liquids. A formula was obtained which may be used to evaluate the resistance of the irrigated packing. Quantitative investigations were also carried out on operating furnaces at Magnitogorsk. Continuous measurements of the lower pressure drops were made under different furnace conditions. Pressures were measured in the tuyere space and the bosh region. A significant transient behaviour of the pressure drop was observed in the irrigated zone as a function of the accumulation of the liquid phase in the bosh region as smelting progressed. Additionally, transient processes were also investigated in the upper furnace zones. The basic cause of the transient behaviour was shown to be the irregularity of burden descent caused by the casting cycle. It was shown that the rate of burden descent between consecutive casts reflects fairly accurately the accumulation and drainage of the liquid products as a result of which heat transfer, reduction and aerodynamic processes assume transient character. In practically all cases of casting a decrease in blast pressure and that over the furnace height of 0.2 kg/cm2 was observed. The analyses of radial gas composition at the stock line showed that compositional variations connected with the casting cycle are most pronounced in the central and peripheral regions, whilst in the intermediate regions the conditions are relatively stable. Calculations show that as casting progresses there is a decrease in the gas flow rate at the periphery and an increase in the centre of the furnace. The transient nature of the aerodynamic processes in packings revealed the existence of an appreciable reserve capacity. Elimination of transience was tested on the furnace at Magnitogorsk and improved operating and economical furnace parameters obtained.

Jan 1, 1975

By J J. Moreno, J Willis, P Garvey

Many of the tailings storage facilities (TSFs) in Australia are upstream raised facilities for which the consolidation of the hydraulically deposited tailings is essential to the stability of the TSF. While much operational consideration is given to limiting the rate of rise of TSFs through careful management of deposition rates to achieve desired consolidation, the rate of embankment raise construction (RoC) is often not given the same level of consideration. Loading the tailings at too high a rate during construction could lead to upstream and potentially downstream failure of the embankment. The Tailings Retention System (TRS) at the BHP Olympic Dam Mine comprises upstream raised TSFs that are continually raised with a zoned embankment. Improving on 20 years of successful embankment raising, there was a desire to understand the acceptable RoC under varying operating conditions and assess upper construction limits to improve operational risk management. To understand the RoC, trial embankment raise construction pads were constructed at different rates and the pore pressure response of the underlying tailings material was monitored. The pore pressure data were used to calibrate the permeability and consolidation characteristics of the tailings in a finite element model (FEM) that replicated a typical embankment raise. The rate of material placement, location of the phreatic surface and construction load were varied in the FEM until failure was initiated. The results were presented as a period (in days) over which the various zones for the embankment raise could be safely constructed. The results indicate direct sensitivity to the depth to the phreatic surface prior to commencement of an embankment raise, as well as the point of application of the construction traffic load. This paper presents the study approach, challenges experienced in modelling the construction methodology, the study results and their relevance in the improvement of understanding of RoC at the BHP Olympic Dam TRS.

Jul 1, 2021

By Matsumura T, Takematsu T

The Brown Coal Liquefaction Process (BCL Process) has been developed by Nippon Brown Coal Liquefaction Co., Ltd. (NBCL), and a 50-ton-per -day Pilot Plant has been partially completed and put into operation by Brown Coal Liquefac- tion (Victoria) Pty., Ltd. (BCLV) at Morwell, Victoria, Australia. This Project has been sponsored by New Energy Development Organization (NEDO), an or- ganization associated with MITI, and has been promoted as a National Project with funding by the Japanese government. This project has also been conducted as a cooperative technology de- velopment project between the Japanese and Aus -tralian governments since 1980 and has been supported by the Victorian state government and

Jan 1, 1987

Longwall mining operations have been in place in Australia since the early 1960s. This mining method is currently used to extract the bulk of coal obtained from underground mines in Australia (CSIRO, 2010). Despite the high tonnages extracted the expected utilisation of much equipment remains relatively low. To some extent this level of utilisation is influenced by the variability in conditions inherent in the mining process. This variability in production rates presents challenges to those attempting to design a coal clearance system. The difficulty is to design a system that has sufficient capacity to support production, without over capitalising or incurring high operating costs. The need to allow for a series of largely unplanned events in the design of a coal clearance system makes simulation modelling an ideal technology to employ. Simulation modelling is a methodology that allows a system with interacting components to be modelled over time, while explicitly taking into account unplanned events that may disrupt operations.This paper discusses how dynamic simulation models have been used to assist in the design of coal clearance systems. Typically this type of modelling has been used to look at the likely profile of production rates from the Longwall shearer and to determine how well various proposed combinations of belts, bins and stockpiles would support production.

Sep 26, 2011

By Ranklin W. J

The mechanism and rate-limiting step of carbonaceous reduction of zinc from slags was investigated in the laboratory. Disks of graphite were rotated in ZnO-containing slags at various speeds for fixed periods at 1250 to 1325¦C. The mass loss was used as a measure of the amount of ZnO reduced. Application of the Levich equation indicated that at rotation speeds at which it is valid, the reduction was chemically controlled with an activation energy of 27 kcal/mol. At zero rotation speed the reduction of ZnO by carbon appeared to be slag-phase mass transfer controlled with an activation energy of 38 kcal/mol. An increase in the FeO content of the slag increased the rate of reduction while an increase in sulphur content decreased the rate of reduction. When FeO was present in the slag, reduction appeared to occur by a combination of indirect reduction of ZnO by carbon and by reduction by FeO with reduction of Fe203 back to FeO by carbon. The effect of sulphur was consistent with a surface blockage mechanism due to the surface active nature of sulphur in slags.

Jan 1, 1993

By C J. R Hart, J K. Mortensen

The distribution of mineral deposits within northwestern North America (Alaska, Yukon, and northern British Columbia) allows for an in-depth examination of the metallogenic patterns of a growing continental margin. A more complete understanding of the tectonic evolution of this part of the Pacific Rim, achieved over the last 15 to 20 years, now allows for the placement of ore systems into a well-defined plate tectonic framework. Ore deposits older than about 185 Ma represent hydrothermal systems that were active in the platform/shelf environment of ancestral North AmericaÆs miogeocline or hydrothermal systems developed in oceanic arcs and continental fragments more distal to the craton. These include important SEDEX, VMS, and pre-accretionary porphyry deposits. In contrast, most mineral deposits younger than about 185 Ma were formed within the growing Cordilleran orogen, as terranes were accreted to the continental margin during interactions between the North America and Pacific/Farallon/Kula plates. Such syn- to post-accretionary mineralised systems include many large lode gold and porphyry/skarn systems.

Jan 1, 1999

Confirmation of significant mineable reserves of high grade silver ore at Elura Mine has led to the development of a high cost, high recovery mining system. At the contact of oxidised and sulphide ores lies a supergene zone of enrichment which has provided a contrast, not formerly imagined, to Elura's primary development and stoping operations. Because of the soft nature of the ore, intense ground support practice has been combined with a panel cut and fill continuous mining system to extract a reserve of small, but most valuable Proportions.

Jan 1, 1988

By Boshou B

In China, there are approximately 3,000,000 million m3 of gas (methane) included in highly gassy mines liable to coal/gas outbursts; the amount of methane pre-drainage possible is estimated at 400,000 - 500,000 million m3. At present, methane drainage has been carried out in 110 mines with a total amount of 19,000 million m3 methane produced during the period of 198 1- 1986. The methane drainage in coal mines of China can be divided into three types: from adjacent seams, from working face seams and from goafs, all with good results. In recent years, general attention has been paid to integrating methane drainage into the mining system but methane drainage from old goafs has to some extent been developed as well.

Jan 1, 1988

By Dhawan AK

On 8 July 1993, a landslide of about one million cubic metres of rock blocked the river Satluj near Sanjay Vidyut Pariyojana - Bhaba project and caused flooding into the Bhaba Power House (120 MW) resulting in suspension of power generation. The concerned authorities desired an early removal of the blockade by an underwater blasting operation into the over topping water to reduce the water level at the blockade and resume power generation in the power house. In the absence of underwater drilling, it was essential for the blasting technique to be used where no cavity to confine the explosive was required. For this reason mud capping and plaster shooting with directional throw were used and additional specially fabricated mild steel pipe charges were used under high current for an underwater trenching operation. By employing these techniques the river blockade was removed up to the required depth and on 8 September 1993 the Power House resumed the power generation.

Jan 1, 1995

By R Berry, S G. Walters, J A. Hunt, D Collett

The texture of an ore type is fundamental in understanding the metallurgical behaviour of an ore. This study will show examples of how quantified textural attributes (mineral shape, grain size and mineral association) can be obtained from automated and scanning electron microscope (SEM)-based microscopy and utilised using advanced image processing techniques. Examples will be shown of integrating quantified and semi-quantified meso- and macro-scale textural attributes as well as how they relate to texture-based visual logging systems. The implications of texture for processing behaviours such as comminution, liberation and recovery will be discussed. This research is part of a major collaborative geometallurgical project undertaken at the Centre of Excellence in Ore Deposits (CODES, University of Tasmania) and the Julius Kruttschnitt Mineral Research Centre (JKMRC, University of Queensland). The authors wish to acknowledge financial support and permission to publish from the sponsors of the AMIRA P843 GEMIII project.

Jan 1, 2008

By Chamberlain A. C, Fisher N, Avraamides J

The thermal decomposition of sodium ethyl xanthate (SEX) adsorbed onto activated carbon was studied by coupled thermogravimetric analysis-Fourier transform infrared spectroscopy (TG-FTIR). Two discrete mass losses were observed, in the temperature ranges 100 - 230¦C and 200 - 340¦C. The same two gases, carbonyl sulphide (COS) and carbon disulphide (CS2), were the main gases evolved in each of the mass losses. Samples of activated carbon from two industrial plants were obtained and analysed by TG-FTIR. COS and CS2 were not detected in one of the samples. The other sample did show evidence of COS and CS2, which indicated that fouling of the carbon by SEX was still present. Other organic compounds were detected in the evolved gas stream of both samples, indicating the presence of organic reagents other than SEX.

Jan 1, 1996