Search Documents

By N Lewis

Recent major urban trunk sewer infrastructure projects in Melbourne have involved construction of nearly 10 km of tunnel boring machine (TBM) driven tunnels in a range of geological conditions varying from soft alluvial soils to hard volcanic rock. To provide both construction and permanent access to the new trunk sewer network, a total of 17 shafts between 5 m and 13 m in diameter, and up to 64 m in depth have been constructed. This paper describes the design and construction of the temporary shaft support systems for the shafts.The range and variability of geological conditions at each shaft site required the adoption of the following shaft support systems across the projects – jet grouting, sheet piles, diaphragm wall, secant pile, contiguous pile, reinforced shotcrete rings and rock bolts.Groundwater control, settlement, TBM launch and reception chambers at the shaft base, chambers and TBM launches at mid-depth of shafts, connection shafts between new and existing sewers and bypass pumping shafts are among the challenges that have been met.This paper reports on the some of the challenges involved and experience gained in developing design and construction solutions for large diameter shafts that are excavated within varying geology in Melbourne over the past three years.

Mar 8, 2011

The light microscopic study of the physical structures of coal and associated mineral matter is an important technique in providing information on the characterisitics and possible behaviour of coals in industrial processes. However the ultrafine nature of coal and mineral particles together with the limits of resolution of the light microscope restrict such studies. Scanning electron microscopy (SEM)with its better resolution and higher magnifications is the means by which further information on coal properties can be obtained. An associated energy dispersive X-ray specrometry (EDS) method allows non-destructive in-situ chemical analyses to be carried out at the same time.

Jan 1, 1989

By Omnes G

Sixty Schlumberger electrical soundings were carried out in the Depot Springs area, near Agnew, Western Australia as part of an investigation into the availability of groundwater for the Agnew nickel project. The object of the survey was to locate calcrete aquifers related to Tertiary drainage channels on the Pre- Cambrian surface. The electrical soundings were initially interpreted using sets of master curves and auxiliary point methods. Electrical sections were produced and contour maps prepared of apparent resistivity for AB=80m, total conductance of the overburden and transverse resistance.

Jan 1, 1975

Computers and other microprocessor technology lead the world of technological change. Nevertheless, the real advances in the world at large are not necessarily in the computer industry, but in the industries whose economics benefit most by the advances that this computer revolution makes possible. The minerals industry has always been in the forefront of this advance. Technological change in the era preceding the industrial revolution, and the mining industry's part in it, provides an instructive lesson for what is happening today. Strong parallels can be drawn for predicting future advances. With each technological advance allowing more efficient production comes a re-alignment of economics - absolute and relative changes to prices, to quantities demanded, and to other market characteristics. This re-alignment applies not only to the mineral industry, but also to the world at large. Adaptability, rather than technical advancement per se is the key to survival and growth in a changing world. 'Adaptability' as a concept is easy to support. As an operational philosophy it is not so easy to implement. As a goal for planning, it is much harder to quantify. A fixed scenario of a future world may provide helpful guidelines, but a scenario that demands adaptability to an uncertain future world is much less definite. Of course, everyone else in the world is also uncertain about the future, and they are making their plans using different assumptions. This virtually guarantees that our future will turn out different to our expectations. This is in part what Hayek (1945) calls the 'knowledge' problem. Until now, most of the planning and technical research undertaken in the world has ignored this problem. This ignorance is a luxury that we can no longer afford. The paper looks at the history of technological change and highlights the characteristics of successful technological revolutions. 'Adaptability' to unforeseen circumstances is the key to success in this environment. The paper examines the knowledge problem from the perspective of the mineral industry, and suggests a number of directions for maximising the returns from application of computer technology in this important area.

Jan 1, 1995

By Stuart M. S, Allen P. B

The Childe Harold deposit was mined by the Granny Smith Joint Venture (GSJV) from late-March through to early-December 1993. This was a fast-tracked mining project whose history began with an offer to purchase agreement being signed at the end of October 1992. A feasibility study was completed by the end of December 1992 after completion of a reverse circulation (RC) and diamond drilling program. Subsequent additional definition drilling culminated in a remodelling of the reserve by March 1993, by which time all necessary governmental and company approvals had been granted. The crucial aspect of mining Childe Harold quickly was to maintain oxide ore supply to the Granny Smith mill at the maximum possible rate for blending with existing fresh ore stocks. As a result, high production rates had to be balanced with

Jan 1, 1994

Changes in mining technology have led to an increase in the number of underground sulfide dust explosions reported in Australian and overseas mines. Samples collected at the Elura mine consisting primarily of pyrite, pyrrhotite, arsenopyrite, sphalerite and galena, were tested in 8 litre explosion chamber. The dusts were found to be capable of producing dangerous dust explosions with maximum explosion pressures of 440 kPa and rates of pressure rise of 5200 kPa/s. The hazards of a sulfide dust explosion are associated with the pressure wave and flame front of the explosion and the toxic gases remaining after the explosion.

Jan 1, 1984

By Bockhorst R. W, Christopher D. A

Over the past fifteen years, horizontal drilling in coal seams for advance degasification has become an established practice in the United States of America. Consolidation Coal Company pioneered the development of the horizontal drilling system and licensed the technology in the U.S. A. and to Du Pont (Australia) for commercial production. This paper discusses the most recent developments in the equipment design, especially the borehole telemetry system, known as the Downhole Drill Monitor (DDM).

Jan 1, 1988

By J B Tucker, A T. McGrath

Situated in north-west Queensland, Australia, the Ernest Henry Mine (EHM) has been producing copper and gold since 1996. Owned and operated by Glencore Xstrata, ore is currently sourced from a newly developed underground sublevel cave (SLC) mine below the old EHM open pit (the pit). Ore feed to the concentrator is supplemented by satellite open pits comprising the Mount Margaret operation.The transition from open pit to a producing underground mine involved a complex extraction sequence for the first two production sublevels on RL1650 and RL1625. Underground mining during cave initiation was further complicated when south wall instability prevented completion of the final open pit shell. The transition mining phase included mass firing of an inclined crown pillar between the initial SLC void and the pit followed by a combination of transverse and longitudinal SLC mining.The inclined crown pillar mass firing was the first significant milestone in the extraction of the transition ore block. Comprising approximately 890 000 t of in situ material; 70 000 m of drilling was charged with 351 t of emulsion and 6026 electronic detonators to initiate the single mass firing. The firing contained five direction changes over 19 seconds making it one of the largest and most complex underground blasts ever conducted in Australia.Risk management was integrated into every facet of the technical and operational planning and execution of the transition mining phase, whilst maintaining daily mine construction and production commitments. This paper provides a detailed overview of the transition objectives and constraints, mining method selection, post mass blast outcomes and the journey ahead.CITATION:McGrath, A T, Campbell, A D and Tucker, J B, 2014. Transition of the Ernest Henry Mine from open pit to an underground sublevel cave, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 297–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By A Agasty, O Langefeld, MáKellner, E Clausen

The lowering of the pollutant concentration limits at the workplace subjects the mining industry to higher requirements for dilution; this situation is worsened with the current discussions within the European Union (EU) to set new stricter exposure limits for nitrogen oxides in the workplace. This is directly reflected in the performance of the mine ventilation system, which may need to be revised to meet the new standards. The after blast re-entry time, being inversely proportional to the threshold limits, will be higher for a lower limit. This in turn increases the down time for production from the blasted area.Numerical tools have been very useful in predicting the effectiveness of ventilation. This study aims at analysing the dilution time for NOx gases from an ANFO blast in a room and pillar panel. The effect of changing the ventilation on the dilution time is studied next, which helps with the selection of a suitable ventilation system.CITATION:Agasty, A, Clausen, E, Kellner, M and Langefeld, O, 2013. After blast re-entry time for a room and pillar operation, in Proceedings The Australian Mine Ventilation Conference , pp 179-186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

The application of methods using large diameter down holes has become an important facet in both the development and stoping operations of mines within the Aberfoyle group. Holes of up to 98 metres (vertical) and 78 metres (inclined) have been successfully used in stoping operations. A number of rises have been developed to meet ventilation, servicing and escape-way requirements. The most ambitious rise to date has been a..vertical 93 metre long by 4.50 metre square ventilation rise. Although some early problems were experienced, the ultimate successful completion of this rise has enabled the technique to be incorporated with confidence in future mining plans. This paper summarises experience in long hole rising techniques, their evolution from the original cratering concepts, and the approach to further development of these techniques.

Jan 1, 1982

Computers represent substantial capital investment. A better return on that invest- ment comes from more effective use of the computer's facilities. By using Telecom's data communications facilities, more people in more locations can have ready access to those facilities.

Jan 1, 1983

By Dorricott M. G, McAllister J

This paper is concerned with the application of a probabilistic approach to the risk assessment of mining projects.In current practice, sensitivity analysis is the most commonly used deterministic approach of accounting for the uncertainties involved in mining project evaluation, while Monte Carlo simulation is considered to be the best probabilistic method available for the same purpose. The methodology of the approach proposed in this paper is as simple as that of sensitivity analysis. However, the results obtained can be more comprehensive than those obtained from Monte Carlo simulation. Various important statistical features, such as correlation and skewness, of the basic random parameters can be easily taken into account by the proposed approach. Example studies are demonstrated. Lotus 123 was employed for the associated probabilistic calculations.

Jan 1, 1992

By J Krawcz, S Wasilewski, W Mironowicz

Barometric pressure and its variation in deep underground workings have a considerable effect on ventilation conditions. Pressure changes which create transient states of air flow and air parameters in workings are especially significant. Experiments have shown that pressure changes have a remarkable effect on air parameters at mine workings and hence, attempts to evaluate the scale of this phenomenon are of value. Continuous monitoring of the barometric pressure on the surface of mines allows for the detection of changes in pressure which undoubtedly influence alternations of pressure in the underground areas of mines. Very important factors are the internal disturbances of pressure within a mine ventilation system due to variable conditions of fan operation and the operation of a winding machine where a mine cage moving in a shaft causes piston like disturbances. Local transient disturbances caused by temporary opening/closing of air stoppings due to personnel or underground transport traffic are of importance. The results of over two years of observations of barometric pressure and its influence on pressure variation in underground mine workings are presented in this paper. The observations were possible through the installation of pressure sensors at selected points of the downcast shaft in a mine. Of interest are the observations of the transient states of pressure and other air parameters caused by emergency fan stoppage, movement of a mine cage and changes due to the opening of air stoppings. Data acquired during experiments of opening and closing air stoppings were used for the validation of a flow model in a long working.

Jan 1, 2005

By M J. Noy

The automated measurement of rock fragmentation particle size distribution in the muck during muck excavation has been developing over the last 16 years. The introduction of stereo camera imaging of the muck has provided improved automated particle segmentation for image-based measurement algorithms. Recently, a new vision system processing algorithm has been developed. The inclusion of 2D texture in the analysis has provided a significant improvement in the definition of the finer size fractions, which has resulted in the automated analysis no longer requiring calibration.The previous stereo vision system algorithm required analysis calibration to account for poor ‘small particle’ definition in the 3D surface profile. This was because of the depth perception limitations of the stereo camera system at greater than 8 m. The new algorithm has been implemented on a number of shovel-installed vision systems, and the algorithm’s performance in automated analysis has been assessed against a diligent manual analysis of the same fragmentation images. The new algorithm provides improved distribution resolution and accuracy.CITATION:Noy, M J, 2015. Evaluation of a new vision system algorithm for automated fragmentation measurement from a shovel, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 721–726 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Dixon D. R, Sparrow G. J

Pressure leach liquors from the pressure oxidation of a bulk flotation concentrate prepared from a complex Cu-Pb-Zn sulphide ore were treated to remove iron, either by pressure oxidation (the Hematite process) or with particles of magnetite (the Magnetite process), followed by cementation of various metals with zinc dust to obtain a purified solution from which zinc was electrowon. Satisfactory iron removal was achieved by both processes after neutralisation to pH 4.5 or 5.5. Pressure oxidation of the liquor at 200¦C and 690 kPa oxygen overpressure, conditions similar to those of the Hematite process used in the zinc industry, resulted in the precipitation of the iron as hematite. With the Magnetite process, an iron hydroxide was precipitated onto magnetite at atmospheric pressure and ambient temperature and removed by a magnetic separation step. The performances of both these processes for the removal of iron are compared. It is concluded that the Magnetite process offers considerable cost savings. Other impurities, in particular arsenic, were also removed with the iron in both processes. Cementation at pH 5.2 and 85-90 ¦C with 3.5 g/L zinc dust reduced the levels of copper, cadmium, and nickel to a satisfactory level and subsequent electrolysis in a laboratory cell gave an acceptable deposit of zinc.

Jan 1, 1989

By Jensen B

The investigation of the explosion characteristics of nine Bowen Basin (Central Queensland) dust samples in a suitable coal dust explosion chamber using a new dust concentration probe provides several advances in the area of coal dust explosibility testing. The 20 litre explosion chamber, of novel design, uses rotation of the main body of the chamber together with air jets for dust dispersion, and allows testing of different types of explosion initiators and analysis of the explosion characteristics of coal dust/methane mixtures of varying concentrations.A new development was a dielectric dust probe for the measurement of coal dust concentration. A capacitive micrometry technique was successfully adapted to measure dust concentration. The system uses a ratio-transformer bridge for measurement of small changes in a capacitive probe designed to sample a representative volume. The device is accurate, and is capable of operating in the hostile environment within the explosion chamber.The explosion chamber and dust probe characterise the explosive potential of coal dust samples by determination of the dust lean limit concentration in varying mixture with methane. Plots of lean limit points obtained in this way present an explosion curve for each sample which indicates the potential of the coal dust/methane to explode under the conditions of initiation in the chamber. The explosion curve obtained for each sample presents a unique signature that appears to reflect the physical and chemical characteristics of the dust.The results from this series of laboratory experiments appear to provide a useful index and indicate potential areas of interest for future research.

Jan 1, 1991

By J Rock, K Bambrook

"Hanwha Mining Services was approached by Glencore Coal to provide a series of (trial) demonstration blasts at its Clermont coalmine. The intent of the project was to trial a bulk explosive product that would be able to provide sufficient energy for the ground type encountered without production of post-blast fume. Three blasts were loaded using the patented XLOAD bulk explosives with a density of 1.00 g/cc. XLOAD bulk products are water resistant explosives that can be loaded at densities much lower than traditional (generic) water resistant heavy ammonium nitrate – fuel oil (ANFO) or pumped blends with significantly reduced risk of fume. In addition, these products have detonation characteristics that generally deliver a higher heave partition than conventional bulk products and hence improve muck pile looseness and digability.The priority key performance measures included the absence of fume from blasting, being at least cost neutral and providing similar if not improved shovel dig rates. The design for the initial blast took a conservative approach to ensure the key blast outcomes of fume control and fragmentation were achieved.The second blast used the same pattern dimensions as the benchmark bulk product used in this area to provide a cost neutral comparison with the benchmark products that had been used over the prior six months. This resulted in a 20 per cent lower powder factor than would have otherwise been used. To test the suitability of XLOAD, this shot was slept for over two weeks between loading and firing in geology where the sleep time is typically kept to a few days to minimise the fume risk.The third blast utilised a slightly larger drill pattern to push the capabilities of XLOAD and provide a cost neutral comparison between the trial product and the traditional benchmark products. All three blasts were fired with no fume observed, no recordable incidents and good fragmentation. Shovel productivity from all three of the trial blasts was excellent with higher average instantaneous dig rates being recorded (average six per cent improvement against the instantaneous dig rates recorded for the benchmark blasts).Citation:Rock, J and Bambrook, K, 2016. Controlling Blast Related Fumes with Unconventional Explosives, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 39–49 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

As part of its Concentrator operation Hamersley Iron Pty. Limited uses wet high intensity magnetic separation to upgrade shaley low grade ore in the minus 0.5mm size range. Materials handling problems, largely caused by fine ore types and design deficiencies, surfaced in the Fines Treatment Plant soon after Concentrator commissioning in 1979. Surging throughout the circuit impaired process efficiency and added to problems caused by capacity and process control limitations. In 1981 extensive modification works were initiated to supplement minor changes made to that date. The new circuit significantly increases capacity and provides greater process control.

Jan 1, 1978

The Matakan Unit of New Ireland, Papua New Guinea is a highly fossiliferous lagoonal deposit containing numerous coal pods and lenses. The unit is strati graphically part of the massive reefal Lelet Limestone of Miocence age. These organic-rich sediments have a high hydrocarbon potential as evident from microscopical observations as well as Rock- Eval pyrolysis data. The coal is varied in regard to dominant macerals, vitrinite being predominant in some parts and pollen and spores present in sufficient proportions to constitute a cannel coal elsewhere. The highly fossiliferous carbo as Rock-Eval pyrolysis data. The coal is varied in regard to dominant macerals, vitrinite being predominant in some parts and pollen and spores present in sufficient proportions to constitute a cannel coal elsewhere. The highly fossiliferous carbonaceous sedimentary rocks associated with the coal are rich in pyrite expressed in the sulphur content (19.7 - 22.8%). A high primary productivity and anoxic sediment pore waters or just above sediment - water interface have given rise to sufficient organic matter accumulations to yield a potential hydrocarbon source rock. Atomic H/C ratios of the coals are between kerogen type III and type II mainly, expressing the mixed nature of the coal and that of the associated sediments is type II. Early generated hydrocarbons (exsudatinite) have formed from pollen exines filling the pollen cavities and in places filling micro- fissures in the surrounding vitrinite.

Jan 1, 1987

Australian continental crust has accreted and consolidated by thirds: 1/3 during Archean time, 1/3 during Early to mid- Proterozoic time, and 1/3 during latest Precambrian to mostly Paleozoic time. The progression of orogenic systems and the crustal consolidations they represent seem not fundamentally different in basic orogenic processes from better known Mesozoic-Cenozoic examples in that accretionary, continental margin, collisional, and intraplate intracratonic inverted and/or reactivated systems are all recognizable in the tectonic evolution of Australia.

Jan 1, 1995