Search Documents

By Williams P

The assumptions made in conventional (Terzaghi) consolidation theory are not met in a tailings deposit. Finite or large strain consolidation theory must be employed. The paper describes such a consolidation model and its application to the design of tailings impoundments, water management systems, and long term rehabilitation.

Jan 1, 1990

By E J. Coyle, L A. Millington

Tailings storage facilities are geotechnically complicated structures that develop heterogeneous strength profiles and varied porewater conditions. The monitoring of porewater pressures is one of the only direct measurements that can be performed to monitor the performance of a facility throughout its life and is of particular importance in upstream facilities. Foundation underdrainage, continuous and staged tailings deposition, climate inputs (rain, snow, humidity, evaporation, etc), and stratified tailings permeabilities can complicate this critical measurement that introduces uncertainty to stability analyses. These difficult conditions manifest in vibrating wire piezometer measurements as very low or negative pressure readings, both of which are within the instrument’s range of accuracy. However, the data can be difficult to interpret, and a range of interpretations are adopted from optimistic low phreatic surfaces to conservative fully saturated tailings. Where tailings are potentially liquefiable, these very low readings introduce further uncertainty regarding the pore space saturation ratio and liquefaction potential above the estimated phreatic surface. This area of uncertainty is the vadose zone, and its affect on tailings behaviour is not well understood. The two facilities analysed in this paper are upstream, raised embankments with tailings classified as clayey, sandy silt that have been found to be potentially liquefiable. The vibrating wire piezometers (VWP) at both sites show very low or negative readings when they are initially installed near the surface and then go through cycles of re-saturation and de-saturation. Eventually the readings settle as the VWPs are buried deeper within the tailings. The instrumented sections within the tailings column do not show consistent readings that would be indicative of a hydrostatic phreatic surface at either site. Rather, they are highly variable and can be interpreted as either representing a high phreatic surface within the tailings or as a ‘perched’ phreatic zone within the tailings layers. How the VWP data is interpreted has a significant impact on how the facilities are raised and operated. The design outcome for Site 1, which adopts a lower phreatic surface, results in an embankment that meets factor of safety (FoS) requirements under residual strength conditions without any buttressing. Conversely, a conservative (high) phreatic surface has been adopted for Site 2 and has resulted in the facility requiring a significant buttress to meet FoS under residual strength conditions.

Jul 1, 2021

In October 2005 Phelps Dodge mining, a US based company, visited several Australian mining companies and mine sites to ascertain the current applications of risk management methods in the organisation. The results of this review, documented by the author, indicated a ælayeredÆ approach from high level site or major hazard analysis through to face level, æstop and lookÆ, methods. The approaches of several companies were summarised in one simple layered model. This model is helpful to other sites and companies to identify potential improvements but also offers an image of best practice that may assist with the governance of OH&S by both company boards and community regulators. The issue is particularly relevant as we discuss national consistency in mining regulation. This paper examines the layered model, the company and site approaches that helped define the model, as well as the suggested implications of the layered model to governance.

Jan 1, 2006

By B N. Noller, J C. Ng, S L. Bruce

Mining activities can result in the transfer of harmful elements, including arsenic and lead, into the environment. In Australia, one of the potential future uses of rehabilitated mine land is to stock grazing animals. Elemental uptake is dependent on bioavailable fraction for adsorption upon exposure. Bioavailability data are generally lacking in order to provide realistic health risk assessments relating to harmful elements from mine tailings in Australian conditions. Another key component of risk assessment is the ability to estimate a realistic exposure, or dose rate, of the tailings to the grazing cattle over a set period of time. Hence, we aimed to conduct grazing trials directly on rehabilitated tailings facilities in order to provide valuable in situ information on heavy metal dose rates and associated accumulation. For the laboratory-based evaluation of comparative bioavailability, groups of cattle were fed five days a week on a normal diet spiked with mine tailings or soluble pure salts of target elements (eg sodium arsenate, sodium arsenite and lead acetate) for about eight months. For the field validation, cattle were allowed to graze directly on rehabilitated tailings facilities over a similar length of time. Blood and a biopsy of the muscle and liver were periodically collected to monitor arsenic accumulation. At necropsy, blood, muscle, liver, kidney and other saleable tissues were measured for arsenic concentrations. Although this study was focused on arsenic, lead and other metals were also measured. Predictive models for arsenic and other metals have been established to calculate the maximum grazing duration without the risk of exceeding specific food safety guidelines. The outcome of this study is a predictive model for maximum beneficial use of certain rehabilitated tailings for cattle grazing where grazing activities do not impact on the integrity of the tailings dams.CITATION:Ng, J C, Noller, B N and Bruce, S L, 2014. A predictive model for beneficial use of rehabilitated mine tailings for grazing cattle after mine closure, in Proceedings Life-of-Mine 2014 , pp 563–572 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

The New Broken Hill Consolidated Airshaft is the first major undertaking in the development of New Broken Hill Consolidated Ltd's. property, which adjoins that of The Zinc Corporation Ltd. on the latter's southern boundary.The Zinc Corporation ore-body has a southerly pitch. The Zinc Corporation's New Main Shaft is 1000 ft. north of the common boundary, and the general plan of development of the New Broken Hill Consolidated property is by driving south from this shaft on the lower levels. No downcast airway from the surface was available south of the Zinc Corporation's New Main Shaft; this shaft acts as the main downcast to the bottom of the Zinc Corporation mine, the general air flow then being northward and upward to the upcast shaft at the extreme north end of the Zinc Corporation property.Rock temperature is 920 F. at 2000 ft., increasing by 10 Fahr. each 72 ft., the rock temperature at 3000 ft. being estimated at 1060 Fahr. With the general air flow northward from the Zinc Corporation's New Main Shaft, adequate ventilation under these temperature conditions would not be practicable for any great distance south of this shaft without another main airway from the surface. Accordingly the New Broken Hill Consolidated Airshaft is being sunk at a point 1000 ft. south of the common boundary, i.e., 2000 ft. south of the Zinc Corporation's New Main Shaft, to ventilate future New Broken Hill Consolidated workings and that part of the Zinc Corporation mine between the boundary and the New Main Shaft.

Jan 1, 1940

The Mt Whaleback open cut mine South Wall is, in part, developed as an unbenched dip slope. The remainder of the rock slope consists of asymetrical overturned folds which have been locally truncated by major low angle faults. The Mt Whaleback orebody is structurally controlled and therefore extensive structural geology input has gone into the final rock slope design. The design is based on normalised 40 m geological cross sections, but the inherent complexity of the geological structure of the orebody yields a high degree of uncertainty within that interval. There- fore, the final slope bench face and the penultimate bench faces are mapped in detail to accurately establish the geological contacts and struc- ture. The knowledge of accurate geology of final and penultimate faces plays a very important role in the design of controlled perimeter blast- ing. Accurate geology is established mainly by face mapping, and by hole geological evaluation of blastholes to locally refine the current Geologi- cal model.

Jan 1, 1989

By D Kent, J Bullock, M Wilkinson

Over the last few years at Glencore’s Mount Isa Copper Operations (MICO) mining conditions have become increasingly challenging through lower head grades and higher work indices. MICO has had great success improving operating efficiencies and increasing productivity through focusing on technology, innovation and operational discipline. The recent implementation of the Mine Site Technologies (MST) ImPact System has supported the continued transformation of the MICO operations through improved personnel safety and direct measurement of productivity. The ImPact System has implemented new safety systems such as the heavy vehicle proximity detection system, underground personnel tracking system and emergency evacuation dashboards improving the overall safety of the workforce. The ImPact System has facilitated productivity improvements via real-time equipment and personnel monitoring, and the implementation of exception reporting (personnel productivity), KPI reports and production dashboards, and transparent reports highlighting developing maintenance issues.This paper discusses the components of the ImPact System, the current installation at MICO, and critically analyses the implementation processes and right sizing of the system to meet the needs of the business today and into the future.CITATION:Bullock, J, Kent, D and Wilkinson, M, 2017. Productivity and safety improvements supported by MST’s ImPact System at Glencore’s Mount Isa Copper Operations, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 279–286 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By McQuade CV, Riley SJ

Acid mine drainage is an unavoidable consequence of some coal mining operations. Typically runoff pH is below 3.5 and at these pH levels heavy metals are mobilised. Leachate from coal reject dumps may require collection and treatment to raise the pH and precipitate the metals before being discharged.A bi-product of coal mining operations at Clarence Colliery is coarse washery reject. At present the coarse reject is deposited above ground and rehabilitated. Adjacent to Clarence Colliery is the Kable's Transport Pty Ltd sand mining operation. It has been proposed that co-disposal of the rejects from both operations may produce a product whose leachate has near neutral pH.

Jan 1, 1998

By Hendon G. W, Carr F, Jiang Y

A vast majority of the operating longwall sections use shield-type face supports to provide ground control in the United States. As a co-operative research program between the University of Alabama (UA) and Jim Walter Resources, Inc.(JWR), a joint research program is underway to study interaction of shields with surrounding rock masses. A series of analyses on the response of shields are performed using monitored data at a longwall face in a deep coal mine. In this paper, various effects of parameters, such as leg pressure, setting load, developing load, maximum loading rate, pressure in capsule, and convergence between canopy and base, are discussed and recommended as stability indices. A microcomputer program is being developed for instantaneous interpretation of the shield monitored data, and for giving warnings of potential problems. The preliminary results define the effects of the setting load, developing load, and rate of developing load or leg closure rate. The objective of the study is to understand the shield characteristics and their interaction with surrounding strata in real time, then develop a reliable program for maintaining longwall stability.

Jan 1, 1992

By D Newton

The Mt Morgan Minesite in Central Queensland has been subject to both underground and surface gold mining operations since the late-1800s. The site is largely unrehabilitated and poor quality surface run-off and subsurface leachate is contaminating the nearby Dee River. The site is dominated by a large open cut, which now stores contaminated surface and subsurface run-off. Three models were used to simulate the complex hydrologic processes occurring at the Mt Morgan Mine: a rainfall-run-off model, a groundwater model and a storage behavioural model. Study results showed that the open cut is filling with water and will soon spill large volumes of highly polluted water to the Dee River on a regular basis if no remedial action is taken. This will result in a three-fold increase in pollutant load to the Dee River. Based on a consideration of water quality and quantity it was concluded that the first priority for future minesite water management should be the prevention of spills from the open cut. Potential management options to achieve this objective included surface rehabilitation, catchment diversions, modification of the pump-back system and controlled releases to the Dee River during floods. However, assessing the relative effectiveness of these measures required a thorough understanding of the complex surface and subsurface hydrology of the site. The results of a 100 year simulation of hydrologic processes revealed that previously favoured management options would be ineffective in preventing spills to the river. On this basis, a continuous treat and release strategy was proposed as the only reliable method of preventing future spills. The results of this study demonstrate that good environmental management decisions must be based on an understanding of the relevant physical processes and consideration of cumulative effects over an appropriate time scale.

Jan 1, 2003

By F T. Suorineni

Empirical methods are deeply rooted in geomechanics. This is a consequence of the recognised complexity of the nature of the rock mass. The usual assumptions of material continuity, homogeneity, isotropicity and linear elasticity often assumed for soil, concrete and steel are difficult to justify in a rock mass except for mathematical convenience. These assumptions form the bases for most mechanistic, analytical and numerical methods in geomechanics. Believers in empirical methods argue that the complexity of the rock mass and its interaction with structures developed in it is adequately accounted for in empirical methods, which compensate for our ignorance.Franklin (1993) defines empirical design as quantified judgement based on experience. He further states that empirical methods often prove ‘closer’ to the ‘truth’ than the apparently more precise predictions of theoretical analysis, adding that based on real data empirical methods provide a standard against which theoretical predictions are measured and can be judged. This paper takes a critical look at the common empirical methods in geomechanics – rock mass classification systems (Bieniawski, 1973; Barton, Lien and Lunde, 1974; Hoek, 1994a), Laubscher block caving design rules (Laubscher, 1994), the stability graph (Mathews et al, 1981), pillar design equations (Salamon and Munro, 1967; Hedley and Grant, 1972; and their derivatives), pillar design chart (Lunder and Pakalnis, 1997) and failure criteria (Hoek and Brown, 1980; and its derivatives). The common thread in the application of these methods is that in most cases they are often applied blindly without an understanding of the underlying assumptions and database limits. This paper emphasises that users of these methods need to know the underlying assumptions, database limits and inherent hidden risks that are often unmentionable for their satisfactory use. Finally, suggestions are provided for the efficient use of empirical methods and how they can be improved.CITATION:Suorineni, F T, 2014. Reflections on empirical methods in geomechanics – the unmentionables and hidden risks, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 143–156 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By B R. Castley

Consumable materials used in mines are often transported to the working areas down shallow angle decline shafts, typically at anywhere between 10¦ and 30¦ to the horizontal. The winding equipment is usually a relatively small single-drum winder and the material is transported in one or more cars, running on rails in the decline. The winding rope is attached directly to the cars, which are mechanically coupled together. For small rock hoisting declines, the cars are replaced with hoppers or skips. The winder is normally of basic design, fitted with only the minimum required safety devices and very elementary brake control. Since these winders are not ælicensedÆ and are usually located in remote areas, the standard of maintenance on the installations is often poor, leading to frequent accidents, resulting in runaways, derailments and broken ropes. These problems can be overcome easily with the application of the rope haulage principle. When large volumes of ore have to be transported to surface, belt conveyors are used on shallow angle inclines, or high-capacity friction winders are used in vertical shafts. Conveyors are limited to inclines no steeper than 14¦ and vertical shafts with large friction or drum type winders are extremely capital-intensive. Rope haulage systems can be used on decline shafts where the inclination is too steep for belt conveyors and too shallow for conventional drum winders. Rope haulage systems also offer a variety of safety, technical and cost advantages over other winding and transport systems. This paper describes the adaptation of the rope haulage principle to modern requirements and, combined with 21st century electronic technology, explains how the principle can be used as an efficient, safe and practical solution to some problems associated with the transport of materials, personnel and ore in mines. The authors describe the designs, methods of operation, safety aspects, automated control, loading and unloading facilities of modern rope haulage systems used for transporting personnel, material and ore. This paper considers a variety of systems already designed for different applications, from small material-only installations to multi-purpose and large rock-hoisting systems with payloads as much as 180 t. It also describes in more detail, a material transporting system recently commissioned in South Africa.

Jan 1, 2005

Completing its historical role the opera tion of copper blast furnace of the Saganoseki Smelter was terminated in 1970, but it left some interesting data on metal lumps formed at the furnace bottom. Analysis disclosed the lumps to be speiss containing 100 to 10,000 g/t of Au and Ag and stratified to iron speiss and copper speiss. Solidifying temperatures of iron speiss and copper speiss being approximately 1,090¦C and 800¦C respectively, copper speiss precipitated at the lower side. The distribution coefficient of Au and Ag between matte and speiss (g/t Au(Ag) in matte / g/t Au(Ag) in speiss) is in the range of 1 x 10 2 to 2 x 10 ' and 1 x 10 1 to 5 respectively. The higher Cu % is in speiss, the-more An and Ag are distributed into speiss. Except for a few data, these results comfotm well to the range of distribution equilibria of Au and Ag in matte and speiss systems by Gerlach and Others.

Jan 1, 1980

By La Brooy S R, Fenton K

A low grade copper flotation tailing from Telfer containing 1.2% Cu as chalcocite and cuprite and 5 gt-t Au was leached with ammonia, cyanide and ammonia-cyanide mixtures to extract copper and/or gold. Direct cyanidation extracted both copper and gold but consumed about 30 kgt 1 NaCN. Pre-leaching the tailing with an aerated ammonia solution containing 28 kgt 1NH3 and 17 kgtl(NHa)2S0a at pH 10 readily extracted up to 95% Cu in about 6 hours under optimum conditions. However pH and total ammonia concentration were critical factors. Subsequent cyanidation ex- tracted 80% Au using 6 kgt NNaCN. Ammonia-cyanide mixtures werefound to selectively leach gold over copper depending on the concentration and relative proportion of NH3 and CN. The best composition for leaching up to 80% Au from Teller tailing was 1.6 kgt t NaCN and 1.1 kgf 1 NH3 in the presence of 0.3 kgt t Cue+. Such a mixture left only 50 mgL-1Cu in the final solution after precipitation of some of the initially dissolved copper.

Jan 1, 1991

By Y Xu, J Hacker, D J. Williams

Shear strength parameters of compacted clay liners are needed to analyse the stability of mine waste dumps containing compacted clay liners as sealing layers for potentially acid forming waste rock. A representative clay sample was supplied by McArthur River Mine from the mine site in the Northern Territory, Australia, with an average as-supplied gravimetric moisture content of about 13.6%. The clay was compacted in a 100 mm by 100 mm direct shear box at the as-supplied moisture content to a dry density of 1.85 t/m3, representing the field compaction specification adopted by the mine. To determine the peak and ultimate shear strengths of the compacted clay, single-stage direct shear testing was carried out at nominal initial normal stresses of 50 kPa, 100 kPa and 200 kPa, representing shallow depths of burial in the North Overburden Emplacement Facility of about 2.8 m, 5.6 m and 11.1 m, respectively (assuming a waste rock wet unit weight of 18 kN/m3). Three shearing rates of 1 mm/min (rapid), 0.1 mm/min (intermediate) and 0.01 mm/min (slow) were applied to study the influence of shearing rate on shear strength. In addition, the development of a residual shear plane was tested by reversal and re-shearing in the direct shear box. In the first shearing, the peak and ultimate shear strengths are determined. The normal load was then removed and the box rewound to its starting position. The normal load was then re-applied and the specimen re-sheared. Two reversals were applied to each specimen, and it was found that there was no significant reduction in shear strength. Finally, based on a range of shear strengths obtained in the laboratory for McArthur River Mine clay and other materials by various laboratories over time, shear strength parameters for the compacted clay were recommended for use by the mine.CITATION:Xu, Y, Williams, D J and Hacker, J, 2018. Shear strength of compacted clay liner at McArthur River Mine, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 208–219 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By L Lachance, F Flament, D Leroux, S Gariépy

The pervasiveness of poor sampling practices in and around mineral processing plants could seem intriguing in view of the various documented evidences both for causes and consequences. To this extent, this paper revisits the well-documented but lesser-known fact that failure to care sufficiently about how samples are selected and managed is the mother source of almost all sampling biases. The authors believe that the potentially huge leverage between causes and consequences as well as the diversity of people involved in sampling call for a globally integrated solution rather than for a point solution. Such a globally integrated solution has already been put forward by the AMIRA P754 Metal accounting – code of practice and guidelines (AMIRA, 2007) that inherently requires accuracy to be targeted, measured, reported and managed. Furthermore, always in order to avoid a point solution, several layers of protection against biases must be put in place with each one involving a different ownership whenever possible. This is exactly the role intended by the supervisory bias detection method described in this publication. It is based on the continuous monitoring of the expected value of reduced residuals obtained from statistical data reconciliation conducted in a metal accounting context. This supervisory bias detection method is developed in full details after which Monte Carlo simulations are done on a mineral processing plant example for showing how it can be successfully applied for detecting hidden biases.CITATION:Lachance, L, Leroux, D, Gariépy, S and Flament, F, 2014. Detecting sampling biases in metal accounting, in Proceedings Sampling 2014 , pp 109–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By C D. McCullough, M Gerner

Rarely do opportunities arise allowing closure of a mine site to be planned as a key beneficial land use asset within a new urban growth area; particularly so well prior to cessation of mining.Pit lakes are common mine closure legacies for many open cut mines and may form in open cut mine voids extending below the water table upon closure. Mine closure guidelines increasingly require post-mining land uses of equivalent capacity to premining conditions and that minimise long-term post-mining liabilities and maximise benefits to stakeholders and the environment. However, risks presented by pit lakes are regularly neglected in closure planning or are not able to be addressed to allow beneficial end use of the lake or surrounding land.This paper describes strategic planning initiated by quarry owners ten years before mining ceases. In liaison with the planning agencies, the planned closure of a large 100-year-old limestone quarry pit will form a lake on mine completion, with a well-considered beneficial end use in an urban setting in mind. The quarry pit and adjoining land at Batesford South about the edge of the City of Greater Geelong, Victoria, Australia. Geelong is experiencing growth pressures that necessitate development of a new growth area from about 2025.A multidisciplinary expert team assessed the constraints, opportunities and feasibility of rehabilitating the quarry and pit lake and developing the surrounding land as Geelong’s next urban growth area.The concept is exciting and demonstrates that a former mine site could become a valued home to about 40 000–45 000 people. About 30 per cent of the land will also be developed as an ecological riverine corridor including the pit lake that will become a regionally iconic lake as the centrepiece of an urban development.Our paper outlines technical challenges and how these can be met to achieve closure and beneficial use that meets the social, economic and environmental expectations of contemporary urban planning.CITATION:Gerner, M and McCullough, C?D, 2014. Planning for the future – development of beneficial end use from a quarry pit lake, Victoria, Australia, in Proceedings Life-of-Mine 2014 , pp 99–112 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By M Akhtar, E Jak, M Shevchenko

This article presents an overview of the experimental phase equilibria studies of S-containing systems (Ni-Sn-S, Cu-Sb-S, and Cu-Sn-S) and As-containing systems (Fe-Sb-As and Fe-Sn-As). These systems improve the prediction capabilities of FactSage in a 20-component ‘Cu2O’-PbO-ZnOFeO- Fe2O3-CaO-SiO2-S-(Al2O3-MgO-CrO-Cr2O3-Na2O)-(As, Sn, Sb, Bi, Ag, Au, Ni, Co) system for complex pyrometallurgical operations during both refining and recycling. Experiments involved equilibration at predetermined temperatures (300–1200°C) with or without preheating, followed by rapid quenching in a brine. Quenched samples were then directly measured using an electron probe microanalyser. For the Ni-Sn-S system, liquid phases (NiS- and SnS-rich mattes and liquid metal) and solid phases (Ni1+xSn, SnS, Ni3Sn, FCC-Ni, Ni1-xS, NiS2, Ni3Sn4, SnS2, Sn2S3 and β-Ni3S2) were observed. A new Ni3Sn2S2 phase was found to melt incongruently. For the Cu-Sb-S system, liquid metal, matte, FCC-Cu, digenite, Sb, CuSbS2, Cu3SbS3 and Cu3SbS4 phases were observed. For the Cu-Sn-S system, liquid metal, matte, digenite, SnS and Cu3Sn phases were found at liquidus.

Jun 17, 2024

By J Morgan

Regular monitoring of surface deformation over mine sites is important for providing updated information to managers regarding geotechnical risks related to ground instabilities. This is particularly true in cases where unexpected or accelerating movement patterns are observed, as these trends may have implications related to worker safety within active mining environments, as well as continuity of ongoing operations. InSAR is an active remote sensing technique that uses radar satellite imagery to precisely measure ground movement. This technology has started to become a standard tool for monitoring surface stability in many different sectors, including underground and open pit/cut mining applications. In recent years the launch of satellites that collect radar imagery on a more frequent basis, coupled with advances in InSAR processing techniques, has improved both the extent to which movement patterns typical of mining operations can be characterized and the temporal scale on which results can be reported to geotechnical departments. As a result of these developments, InSAR monitoring can now better meet the operational needs of mine sites. An overview of the more recently launched satellites that have a particular relevance to the monitoring of mines is provided, along with an explanation of the InSAR tools that are the most valuable to mine managers and geotechnical engineers. First, broad differences between high resolution X-band imagery and low resolution (but freely available) Sentinel imagery are discussed. Second, the various InSAR tools and their particular applications for different types of mine sites and operations are covered, which include fast delivery deformation maps for short-term reporting, multi-interferometric algorithms for longer-term analyses and rapid movement tracking (RMT) for emergency monitoring or high-risk situations. The ability of the technology to resolve 2D and 3D movement is also touched upon. Practical examples of InSAR application over a variety of mine sites will be presented, as well as surrounding hazards including landslides, to illustrate how InSAR can help provide geotechnical engineers with a picture of surface stability over the full mine site and surrounding areas to help manage risk. CITATION:Morgan, J, 2018. Wide area mapping of ground instabilities from space: InSAR for geotechnical risk assessment and hazard monitoring, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 375–382 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By S Jayakumari, E Ringdalen, V Canaguier

Silicomanganese (SiMn), containing approximately 16–30 per cent Si, is produced in submerged arc furnaces using various Mn sources and quartz as the primary raw materials, along with fluxes and reductants. In the high-temperature zone known as the coke bed, a silica-rich slag is formed. SiMn is produced through the reduction of SiO2 from the slag. Dissolution of quartz into slags with different compositions, the primary slag formed from the Mn sources and flux before any MnO reduction occurred, representing conditions at the top of the coke bed, and dissolution of quartz into a partially reduced slag to simulate conditions inside the coke bed has been investigated. Experimental investigations were carried out to study the dissolution of quartz particles of varying sizes, 5 mm and 25 mm in synthetic slags with different compositions at temperatures between 1400°C and 1600°C, with varying holding times. Observed results are compared with liquidus compositions and equilibrium phases for original and formed slags. Particle size has been shown to be of little importance for the dissolution. Quartz dissolved more easily in slag at top of the coke bed than slag in the coke bed. Complete dissolution was observed after 30 mins at 1600°C in all cases, but not after 0 mins.

Jun 19, 2024