Search Documents

By Menne D. M, Ladyman R

Camel Creek Mine operated by Lynch Mining Pty Ltd is located 65 km west of inghain and 160 kin north west of Townsville in North Queensland. (Figure 1). The Camel Creek gold mineralisation was discovered in mid-1987 in an area previously known for its tin workings. Mining commenced in January 1989 after an oxide reserve of 1.2 million tonnes @ 2.1 g/t gold had been delineated. The first gold pour was in May 1989. The mine developed into a medium sized open cut operation, with full site facilities. The initial mining rate was 500 000 tpa utilising run-of-mine (ROM) heap leaching to recover the gold. By the end of 1990 the wider orehodies were mined and efforts were focused on the narrow orebodies, of width typically less than three metres. Smaller earth moving equipment was employed to selectively mine the narrow orehodies leading to a decrease in the mining rate to 200 000 tpa. The Red Gold deposit (80 000 tonnes « 3.0 g/t to 18 in vertical) was mined in mid-1990 and ore was hauled approximately 8 kin to the Camel Creek heap leach operation. The ore was hauled in a dedicated campaign after being stockpiled. The cost of dedicated ore haulage ensured that only the more exceptional of the remote orebodies could be mined in this manner. The Golden Cup orebody, some 20 km from Camel Creek, was too distant to permit ore haulage. However, this prospect contained sufficient gold (initially 90 000 tonnes @ 3.0 g/t) to warrant the installation of a small mobile adsorption facility. Construction of the second heap leach operation commenced in late-1990. Gold production commenced in early April 1991. Mining of several smaller orebodies remote to the second heap leach facility has been undertaken and further mining is planned. This paper outlines heap leaching practice at Camel Creek Mine and summarises the success of the Golden Cup heap leach.

Jan 1, 1994

By H Kundapen, B R. Bolton, H Davies

The Ok Tedi porphyry copper-gold mine is located in the Star Mountains of Western Province, Papua New Guinea. Open-cut mine commenced in 1984 and is due to cease around 2010. The mine produces a total of 88 Mt of waste annually including 58 Mt overburden and 30 Mt tailings, which are discharged directly in to the Ok Tedi River. Mine derived wastes are transported downstream and deposited within the river channel in a variety of bar forms. The prevailing hydrogeological conditions including, velocity, competency, capacity, gradient, grain size and specific gravity, control the deposition and segregation of these sediments. Periodic exposure of the reactive sulfides to oxygen during fluctuations in the river discharge may result in oxidation, localised acid generation and liberation of metals into solution. To evaluate the significance of this issue, Ok Tedi Mining Limited initiated an investigation of the sediments deposited in the upper Ok Tedi River as part of its overall ARD Management Program. The specific objectives were to: evaluate the acid-forming characteristics of identified high sulfide river deposited sediments; characterise geochemically the waters in contact with sulfide-bearing river deposited sediments; map and monitor exposure areas and oxidation depth of deposited potentially acid forming (PAF) sediments; determine the depositional processes controlling sulfide distribution; and assess lag period, oxidation and metal release rates for the sediments. This work included the analysis of sediment and water samples collected on a 50 + 50 metre grid at six gravel/sand bars. The sediment samples were analysed for total sulfur, ANC, NAG, total sulfur and total copper. Water samples were tested for general water quality parameters, sulfate and a suite of dissolved metals including; Al, Ca, Cd, Cu, Fe-sol, K, Mg, Mn, Na, S and Zn. This paper presents the results of these investigations with particular emphasis on the geochemistry of the river sediments and associated contact waters.

Jan 1, 2003

Recent work on computerised mineral resource databases at the Institute of Geological and Nuclear Sciences Limited has concentrated on the development of the GERM, REGCHEM, and MINLIT databases, and their integration in a Geographic Information System using MapInfo software on an IBM-compatible microcomputer local area network. GERM (GEological Resource Map) is a mineral deposit inventory with national coverage and more than 10 300 entries. REGCHEM (REGional Exploration GeoCHEMistry) is a database of stream sediment analyses from open-file mining company reports, containing more than 14 000 sample sites from the Coromandel and west Nelson regions. MINLIT (MINeral LITerature bibliography) is an annotated bibliography of literature on topics relating to the exploration and geology of mineral deposits in New Zealand, and includes more than 5000 entries for published books and papers, and unpublished mining company reports, university theses, and government reports. Master sets of GERM and MINLIT continue to be maintained on a VAX mainframe network but REGCHEM is operated only in the PC environment using the Microsoft ACCESS database management system software.

Jan 1, 1993

By Stewart R, Manson RA, Haig DW, Perembo RCB, Kruman B

Since the advent of plate tectonic modelling, the Ramu-Markham valley has been thought the site of a classical island-arc/conti- nent collision zone. In this interpretation the units south of the Markham Valley are held to be island are / micrcontinental mate- rial accreted to Australia and those north of the valley are thought to represent a separate Finisterre island-arc terrane. Recent remapping by the Geological Survey of Papua New Guinea shows: (1) there is no terrane boundary along the Ramu-Markham valley (2) the Finisterre Volcanics are probably part of either a fore-arc sequence or oceanic plateau obducted onto a microcontinent/ volcanic-arc composite terrane, accreted to the continental Australian plate. A new tectonic model is proposed for northern PNG and involves: (I) Eocene to Late Oligocene subduction below a microcontinent remote from Australia to produce the Sepik are and related intrusives, the Finisterre Volcanics (fore-arc or possible oce- anic plateau), together with the Alife blueschist. (2) obduction of the Sepik arc in Late Oligocene-Early Miocene times over the advancing Australian plate. This resulted in crustal melting, some of the products of which are the Mid- dle to Late Miocene Akuna and Bismarck intrusive complexes of the Maramuni arc. (3) obduction of the Finisterre Volcanics began in Early Pliocene times and continues today. (4) post-Middle Miocene mineralisation is the result of melting after obduction of the Sepik microcontinent.

Jan 1, 1997

Cable bolts are being used more extensively by the mining industry for many different rock reinforcement applications. The configuration of these bolts has evolved over the last 20 years to meet the immediate needs of industry at the particular time. Most improvements to date have focussed on increasing the mechanical performance with little attention given to issues such as ease of handling, matching response to that of the rock mass or corrosion protection. Ultrastrand has been designed and being developed with this broad perspective in mind so that it will satisfy the ground reinforcement needs of today's and tomorrow's mining industry.Laboratory tests on Ultrastrand prototypes have confirmed that mechanical performance is superior or equivalent to Standard and Birdcage Strand respectively. Preliminary discussions have been held with an installation equipment manufacturer with a view to conducting a trial at a mine site by early-1992.

Jan 1, 1992

By R R. Anand

Recent research by CRC LEME from an Australian mineral exploration perspective, has focussed on regolith architecture and mechanisms of geochemical anomaly formation, within transported regolith. Methods have been developed for the rapid production of regolith-landform maps which is the starting point for understanding regolith architecture in the third dimension. Methods for development of 3D regolith models are less well advanced, and require integration of all available geological and geophysical datasets, but still with a heavy reliance on drill-hole information. The base of the transported regolith û the unconformity û remains the most important regolith boundary for geochemical sampling in transported regolith terrains. A new generation portable spectral logger, employing a broader spectrum can interpret important features from drill chips within the regolith. This allows internal architecture, redox fronts and the all-important interface to be objectively identified. Transported lateritic components can provide vectors to mineralisation in depositional regimes. Palaeomagnetic and new radiometric methods which date individual phases of the regolith provide evidence of different episodes, each characterised by different geochemical dispersion patterns in transported regolith. Along with lateritic residuum, calcrete is prime sampling medium. Calcrete is probably enriched in gold through physical and biological processes, rather than straight chemical processes. In South Australia, the lowermost calcrete layer buried within the depositional regime, especially where it lies directly over the silcrete layer at the buried interface, is the desired sampling medium. Certain gum trees, with deep roots in transported regolith have been shown to record anomalous values of gold and basemetals in leaves, twigs and bark. Anomalous metals in acid-sulfate soil seeps can also provide a window through sedimentary cover in respect of mineralisation in the basement. A number of Yilgarn occurrences of gold anomalies in transported cover, strongly infer hydromorphic and biological mobilisation of gold. This inference is supported by micro-analyses of regolith mineral hosts in hardpans and mottled sediments, which show gold and pathfinder elements prefer to reside in goethite and specific types of clay minerals. This creates anomalies in specific mineral phases. However the inference that that these are sites of mobile or labile metal ions remains enigmatic. Similarly there is inconclusive evidence that selective extractions will provide an anomaly not otherwise detected by conventional total dissolution methods. Hydrogeochemistry is a promising exploration tool for basemetal exploration. The importance of microbes in both the dissolution and precipitation of gold in the Australian regolith is demonstrated. We are on the verge of identifying the functional gene sequence of individual active microbes. A consideration of possible mechanisms for creating anomalies in soils above transported regolith, presents difficulties in facilitating upward movement of ions from the watertable to the surface. Perhaps the best avenues of research lies with surrogate soil gases, and biotic transfers.

Jan 1, 2004

TasmaniaÆs mineral endowment has resulted in 600 abandoned mines. Commonly occurring sulfide minerals such as pyrite and pyrrhotite can generate acid drainage and also mobilise heavy metals. Due to the StateÆs steep topography and high rainfall the risk to water quality in the receiving environments is significant. Surface waters impacted by abandoned mine sites typically showed high sulfate and metal distribution at pH range of 2.0 to 5.0. The impacted waters generally showed metal distribution in the high acid/extreme metal to low acid/low metal range. A similar trend was shown by sulfate distribution. Elevated levels of metals and sulfate downstream from several abandoned mine sites indicated that active sulfide oxidation is occurring and these sites may be potential point sources of metal pollution in the receiving environment. High correlation between metal and sulfate distribution suggests that sulfate distribution in surface waters may be used as a cost-effective investigation tool for preliminary assessment of acid drainage.

Jan 1, 2003

By Lorenzen L, Van Der P F

It is the aim of this paper to review recent research in understanding the role of cyanide in the elution of gold. Under conditions of severe pre-treatment (high temperatures and levels of cyanide), the dynamics of elution are determined mainly by the adsorption equilibrium and the flow conditions in the column. When conditions are less favourable for desorption, transport phenomena are rate controlling. The most important sub-processes of elution are the changes in cyanide, potassium and gold concentrations, as well as the change in passivation of the carbon surface. Mathematical models to simulate the various sub-processes are described briefly.The presence of an irreversibly adsorbed species such as AuCN on the carbon is determined mainly by the pH, temperature and the type of carbon. Cyanide in the pre-treatment step will convert the AuCN to reversibly adsorbed Au(CN)2. Competition between cyanide and Au(CN)z for adsorption sites will enhance the elution of gold, but plays a minor role at elevated temperatures. The most important effect of cyanide is its reaction with the functional groups on the carbon to passivate the surface for the adsorption of anionic metal cyanides and thereby promote the elution of gold. This passivation, caused by the degradation of cyanide, is strongly temperature dependent. Free cyanide in the elution step of an AARL elution is of lesser importance than the cyanide in the pre-treatment step. Elution without cyanide is possible only after cold acid washing, and has been proven on plant scale.

Jan 1, 1992

Since the early 1990s it has been evident that electricity demand has outstripped investment in generation and transmission. At the same time, concerns were being expressed about the risks associated with the run down of the Maui gas field. It is axiomatic that the necessary investments firstly require a stable and supportive regulatory and fiscal environment, and secondly that such investments have long lead times. A unwillingness by successive Governments to fund the necessary infrastructure, however, lead to the profound restructuring of the electricity with the ultimate objective of transferring the investment risk from Government to the private sector. Successive power crises since 1992 result from a failure to put in place a regulatory framework necessary to provide the environment to allow the private sector to make the needed investments within the necessary timeframe. The electricity sector has now stabilised to the extent that the regulatory risks associated with generation investment have been reduced. This does not mean that risk has been eliminated, however, and both economic and environmental issues will continue to constrain investment in some power proposals particularly those in the South Island and especially any South Island coal or gas thermal proposal. This is firstly because of several very simple economic issues:  1. while the South Island may have significant coal resources it lacks a significant electricity market; 2. except for a six to ten week period in a dry year, low cost hydro will price any large-scale South Island thermal out of the market which will restrict any large scale thermal station to a dry year and/or peaking load; 3. except for a six to ten week period in a dry year, export capacity on the HVDC link to the North Island is constrained to around 964 MWe (and 482 MWe from North to South in dry years); and 4. construction of any new thermal plant in the northern half of the North Island will price any South Island thermal station out of the market. There are also significant environmental issues associated with the establishment of a large scale thermally based power station in the South Island. Because the South Island lacks any large scale economically proven gas reserves, the environmental constraints considered are those associated with coal production. A coal mine dedicated to power generation will have significant on-site impacts associated, in particular those associated with disposal of opencast overburden and visual impacts. These will, however, be partially offset by the relative remoteness of such sites to population centres. What cannot be offset, however, is the off-site impacts, in particular, CO2, SOx and NOx emissions, water disposal and acid mine drainage.

Jan 1, 2003

We operate a 50 cubic metre per hour mobile alluvial tin mine on small scattered deposits in the Irvinebank area. Wash is loaded by a Cat. 950 front end loader into the bin of a screening section and screen undersize is pumped to a separate jig unit. Both units are rubber tyre mounted and are shifted once a month when the haul distance gets to about 150 metres. The shift takes about 8 hours.The screening section is sited close to the face with a ramp for dumping in and a one metre drop for the screen oversize which is removed by the loader.A reciprocating plate feeder with variable rate hydraulic drive, feeds wash onto a horizontal 1.2 metre x 2.2 metre two deck Kinergy screen. Minus 10 millimetre undersize is pumped by a Warman 6/4 sand pump with a 37 kW variable speed Reeves Motordrive to the jig unit.The jigs are placed 20 to 70 metres away so that tailings will run back into previously mined ground. Reject stone is used to impound the sand and mud, allowing the water to filter through and return to the feed water pump.An MTE trapezoidal module is used as a primary jig. Hutch product is pumped to an eight cell clean-up jig which we developed ourselves along MTE lines. It has a trapezoidal shape and sawtooth stroke provided by cams. Clean tin is taken from the first four spigots. These consist of clear plastic tubes fitted with taps so that there is no water loss except when the tin is drawn off. Fine concentrate from the last four spigots is put over a curvilinear table which sits on a steel base packed with earth.

Jan 1, 1986

By Bruington T, Perkins J, Hutton R

Natural resource developments are among the largest and most challenging projects taking place in the world. They involve capital intensive investment with long lead times and the management of geological, market, technical, operational and financial issues. A clear strategy is required to manage these projects and this strategy is underpinned by a development Philosophy.

Jan 1, 1997

By N Davies, M J. Coward, P L. Hissey

Mount Isa Mines has four mining operations in Mt Isa with the X41 and Enterprise Mines producing copper and the Lead Mine and George Fisher producing lead zinc and silver. Each stream contributes ore to their respective concentrator at a feed rate and therefore metal ratio set out by the monthly schedule. Mine Planning and scheduling lead to a sales and operating plan (S&OP) and revenue projections which ultimately derives actual revenue /tonne and therefore cost/tonne. At Mount Isa, both the copper and lead/zinc streams produce ore from relatively new operations to be blended with material from more mature operations. It is critical to accurately predict the metal contribution from each operation in order to gauge the relative performance of each mine. Development mining ore contributions are estimated and reconciled, as are stope and bench sources. Performance is continually measured and assessed during extraction and grade adjustments are made to account for underbreak, overbreak and design modifications. It is critical to not understate or overstate the contribution from one operation relative to the other as this can produce a false picture of operational performance. Identifying process improvements are key to improving the business overall. Ore from the lead stream passes 17 measurement stations and two midstream reconciliation points before delivery to the heavy media plant (HMP), where the metallurgical circuit begins. From this point two concentrates are produced. A zinc concentrate for treatment off site and a lead concentrate for further on site processing. The lead smelter takes 100 per cent of Isa concentrates as well as a contribution from BHP-BillitonÆs Cannington Mine.

Jan 1, 2002

By M Henderson, M Hudyma

Mining-induced seismicity at Junction Gold Mine became a serious operational problem in the late-1990s. Assessing the local seismic hazard is an important step in assessing the risk associated with potential rockbursting. This paper discusses the qualitative and quantitative means of assessing seismic hazard used at Junction. In qualitative hazard assessment, the role of the primary factors contributing to mining-induced seismicity and rockbursting are identified. These factors include: rock mass properties, geological structures, mine development, and stoping. A qualitative seismic hazard map has been developed considering these factors. In quantitative hazard assessment, seismic source parameters from an Integrated Seismic System are used to assess seismic hazard. The seismic source parameters found to be relevant to seismic hazard assessment at Junction are discussed.

Jan 1, 2002

By D T. Feinstein, M B. Gotkowitz

In Wisconsin, state laws and regulations governing metallic mine permitting stipulate that protection of groundwater quality be assured indefinitely through all phases of the mining project, including development, active mining, reclamation, and long-term closure. By rule, the Wisconsin Department of Natural Resources (WDNR) requires that permit applicants use a numerical model to assist in the assessment of compliance with this requirement for all proposed mine-waste facilities. As a part of the compliance assessment, model calculations are used to predict groundwater solute concentrations through time at designated boundaries for comparison to current groundwater quality standards. In practice, this modelling requirement has involved the application of numerical solute-transport models. Our review of a solute-transport model submitted by the developers of a proposed mine near Crandon, Wisconsin, provides us with an opportunity to assess the usefulness of transport modelling as a permitting requirement. Recent evaluations of solute-transport models by other workers suggest limitations in predictive accuracy. Our review of the model submitted for this project also identified important limitations due primarily to uncertainty in calibration of model parameters at the undeveloped site. The utility of any model to predict project compliance or non-compliance with numerical standards is limited by the range of uncertainty of key model parameters, such as dispersivity and porosity. Uncertainty in the future behaviour of the solute source(s) also reduces the predictive power. Moreover, the site characterisation provided by the model may have limited power to describe the site condition post-development. Although these inherent shortcomings accompany the use of solute transport models at undeveloped sites, the requirement for model development and the ensuing technical review has substantially assisted in our evaluation of site conditions and project design. Through this process we have identified elements of the waste facility design that are crucial to the environmental viability of the project, resulting in modifications to original project proposals. While results from this model review will be used to evaluate compliance, additional benefits come from the identification of critical design features that enhance groundwater protection.

Jan 1, 2003

With increasing depth of mining, geotech nical factors assume increasing importance in the design and operation of open pit coal mines. Dragline strip mines are particularly sensitive to stability conditions since the draoline is a relatively inflexible machine, particularly in relation to its limited dump- ing radius for overburden disposal. Geotechnical factors relevant to strip mine design include: 1. spoil pile stability 2. wall stability 3. floor stability 4. excavation characteristics 5. groundwater conditions A basic geotechnical investigation pro- gram for new mine feasibility studies is described. This includes: 1. terrain evaluation 2. geotechnical drilling and logging 3. geophysical logging 4. materials testing 5. seismic refraction traversing 6. groundwater studies Such a program will give an overall geotech- nical assessment of the site and highlight any areas which may require further, more detailed Investigations

Jan 1, 1981

By Jensen B, Ofori P, He Y, White E, Stanmore B, Brien M, O&apos

As part of a large AMIRA project, an on-line moisture meter was installed at two mine sites in Central Queensland. This project investigated the factors which control the moisture content of coarse (>0.5 mm) coal from the centrifuges used in conventional coal preparation plants. It was placed immediately after the first centrifuge to isolate the factors pertaining to one machine and its feed.The meter was found to be accurate and precise when compared with manual and mechanical sampling methods. The Grubbs estimator technique indicated that its precision is better than 0.3 per cent at the 95 per cent confidence limit.It has been identified that:1. the variability of the measured moisture contents of coarse coal can be described by normal distributions. Standard deviations of about 0.6 per cent are common; and2. the treatment of the coarse coal on the drain and rinse screens immediately prior to the centrifuge can affect the final moisture content.

Jan 1, 1995

By E Claridge

There are a number of major infrastructure tunnelling projects currently underway or proposed in New Zealand, including construction of new road and rail facilities and the refurbishment of existing road tunnels. These new projects have triggered a rethink of traditional practices in underground fire and life safety and local regulation.While there is a current surge in activity, tunnels have been a signifi cant part of New Zealand’s transport infrastructure for over a century. Despite this background, the new projects commonly face challenges that are symptoms of a national regulatory environment that has aspects that are inappropriate for underground environments. There are inconsistencies in local regional regulation and an absence of national guidance and standards relating to tunnel design. Historically, New Zealand has looked across the Tasman for guidance. Although recent overseas tunnel designs present learning opportunities, the adoption of international best practice and standards may not necessarily address local expectations or needs.This paper explores a number of specific matters affecting the design of road and rail tunnels in the New Zealand context, namely; the Building Regulations and associated local consenting processes and parties, and the responsibilities and needs of the New Zealand Fire Service.The discussion highlights the importance of a collaborative approach involving the designer, asset owner, regulators, emergency services, and other parties, and ensuring up-front clarity in design responsibility and ownership of residual risk.

Mar 8, 2011

By Trueman R

If continuous mining systems are to be successfully applied in metalliferous mines then reliable models will be needed to predict rock cutting machine advance and tool wear rates for effective machine selection before mining commences. Many of the predictive models developed to assess cuttability in situ are over-simplistic. As a result they tend to be both site and/or machine specific. Nevertheless very detailed models have been developed for full face machines which are capable of accurate cuttability predictions in a variety of rock mass conditions and for a variety of machine and tool configurations. However, models to predict productivity and tool consumption for partial face machines are not as well advanced. There is a need to develop reliable models for partial face machines such as Roadheaders, the Robbins Mobile Miner and the HDRK-Wirth CMM, as these types of machine are likely to predominate in a mining environment. The paper outlines the current state-of-the-art for predicting cutting machine performance and the work being carried out within the Centre for Mining Technology and Equipment (CMTE), in collaboration with the Australian mining industry, to advance our capability in this area.

Jan 1, 1995

By E Cunha, D Roldao, TáTamantini, J F. C L Costa, T Webber, C Monteiro

The main problem of geostatistical simulations is to reproduce the real characteristics of the mineral deposit when there are few conditioning data. In this case, the geological interpretation, based on structures, geophysics and geological maps, plays the major role in terms of resource evaluation.The paper investigates the use of principal component analysis (PCA) to help classify multiple geostatistical categorical simulations considering the similarity among them and the interpreted model, herein referred as training image (TI).An iron deposit with four lithological facies, in a specific horizontal plane, was used as case study for two-dimensional (2D) simulations. Sequential indicator simulations (SIS) was used to obtain ten equally probable 2D images, which were generated and compared against the interpreted model (TI).In this study, 11 random variables are comprised by the vector of ten SIS realisations plus the training image (TI). The similarity between the TI and each SIS realisation is measured using the angle between the TI and SIS vectors projected in the new coordinate systems (PCA factors). It is possible to order the SIS realisations from the highest to the lowest PCA factor taking into account the TI similarity.The visual analysis of the images shows coherence in the PCA results as a method to measure similarity. This methodology can be used as a post-processing tool to rank simulation results and to select the ones which better represent the prior known geology or to compare the quality of different methods of simulation.

Sep 26, 2011

By M Olsen

"Segregation of conveyor roadways is a ventilation practice that is being increasingly applied in Australia. It is largely driven by the legislated requirements in Queensland pertaining to separation of escapeways from the mine. This legal requirement was based on a recommendation from the Moura No. 2 WardenÆs Inquiry (Windridge, 1996) into the mine disaster that claimed 11 lives. The report recommended: ... the introduction of a requirement for all underground mines to have one intake airway that is completely segregated from other parallel intake airways so as to provide two separate means of egress from the mine via an intake airway.This recommendation seeks to assist mine workers in escape from a mine after a fire by providing them with an airway that is free from smoke or contaminants.The concept of an airway being æcompletely segregatedÆ is an ideal that is challenging to implement in practice when considering the effect of leakage. The practice of belt segregation is concerned with the potential for fires in the belt roadway although there are numerous other potential fire sources in underground coal mines. A review of segregation practices has been conducted applying ventilation engineering principles. Four different scenarios have been analysed with regard to the effectiveness of the segregation stoppings in preventing potential fire contaminants migrating to other parts of the mine. The results show that in some cases the benefits of segregation to a person evacuating a mine in the event of a fire range from beneficial to detrimental. This is influenced by many factors including the location of that individual in that particular mine. There is room for improvement in the design and implementation of escapeways in underground coal mines. Escapeways need to be planned and designated with regard to the potential sources of fire, pressure differentials between escapeways and the operational practicalities of maintaining the pressure differential between them.CITATION:Olsen, M, 2013. Belt road segregation and escapeways - Compliance or risk management?, in Proceedings The Australian Mine Ventilation Conference, pp 311-318 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 1, 2013