Search Documents

By B. H. Sage

IN recent years there has been an increase of interest in the flow of gases at relatively high pressures. Hydrodynamic calculation of the energy losses in the flow of gases in conduits, as well as through the porous solid materials constituting natural petroleum reservoirs, requires a knowledge of the viscosity of the fluid at the pressure and temperature involved. Although there are numerous publications concerning the absolute viscosity? of hydrocarbon gases at atmospheric pressure, there appears to be little information available relating to the effect of pressure upon the viscosity of these gases. Vogel28 determined the viscosity of methane at 32° F. and atmospheric pressure. His measurements at 32° F. were later substantiated by the measurements of Rankine and Smith17 at 63° and 212° F. Ishida12 also reported values for the viscosity of methane at atmospheric pressure. Trautz and Kurz26 measured the viscosity of propane at atmospheric pressure, from 83° to 530° F., by the use of a short capillary tube. Rap-penecker18 determined the viscosity of gaseous isopentane at elevated temperatures. Day' made an accurate investigation of the effect of pressure upon the viscosity of n-pentane and isopentane at pressures from 2 lb. per sq. in. ? to the vapor pressure at 77° F. (approximately 9.8 and 13.3 lb. per sq. in., respectively). Earhart5 reported data upon the viscosity of several natural gases measured by the long capillary-tube method. The viscosity of air, at atmospheric pressure and 73.4° F., was measured by Harrington7 by the rotating-cylinder method. Kellstrom13 has recently made an elaborate investigation of the viscosity of air at atmospheric pressure. The latter work is perhaps the most accurate investigation of the viscosity of a gas that has been made. .

Jan 1, 1937

By Paul M. Tyler

FOR the same reason that water is not missed until the well runs dry, the roles of many industrial minerals in wartime are often overlooked. In contrast to the growing shortages of many metals, our supplies of most nonmetallic minerals are limited only by our machinery for taking them from the ground and by our processing facilities. With few exceptions, the demand for increased supplies has been met without fanfare or delay. Only Brazilian quartz crystals, certain kinds of mica, and, latterly, industrial diamonds are on the so-called strategic list, although asbestos, beryl, corundum, cryolite, fluorspar, crucible-grade graphite, ilmenite, iodine, kyanite, monazite, nitrates, rutile, and zircon have caused more concern among those responsible for procurement and are included in our preclusive buying programs. Such specialties are needed urgently, but they are far less important in the over-all picture than the more abundant minerals.

Jan 1, 1942

By D. F. Gibbons

THIS investigation was undertaken in order to gain further information on the mechanism of plastic deformation of iron at temperatures between room temperature and 77.2°K, and also to contribute to our understanding of the low temperature brittleness phenomenon that occurs in both the tensile and impact tests. It was decided to study as pure an iron as possible and to use the tensile test in order to simplify the problem as much as possible. Two series of iron were used throughout the investigation: iron A, obtained from the National Research Corp. and supplied as gas-free, high purity iron; and iron B, obtained from Fast' and produced by melting iron under purified hydrogen. Typical analyses of samples of both irons, after fabrication, are given in Table I. The main difference in composition of these irons is in their nickel and oxygen contents. Nickel has a very large solid solubility in iron. However, oxygen has an extremely small solid solubility. An attempt was made to reduce the oxygen content still further by remelting under purified hydrogen. This was successful in reducing the oxygen content to -0.0006 pct. However, no results on tests of this iron are included, since difficulty was encountered in fabricating the ingot. Wire specimens 1 mm in diameter were used for the investigation. The wires were produced from the ingots, as supplied, by cold rolling and swaging, with intermediate vacuum anneals at 700°C. Care was taken to reduce preferred orientation in the wires to a minimum by keeping the percentage of reduction in area between anneals of 30 to 40 pct. X-ray transmission photographs showed no indication of preferred orientation. The final grain size of iron A was 20 to 24 grains per linear mm and of iron B, 16 to 18 grains per linear mm. All specimens were tested in the decarburized and denitrided condition unless otherwise stated. The procedure was to pass hydrogen, saturated with water vapor at 26oC, over the specimens at 730°C for 2 hr. The specimens were quenched in iced water and then annealed in a vacuum of - 5x10-6 mm Hg for one day at 560°C to remove hydrogen. Higher temperatures were used for the vacuum anneal but this temperature was found to be quite satisfactory in removing hydrogen. The specimens were slow-cooled after the vacuum anneal. Where it is stated that the specimens were carburized, the specimens were given an identical decarburizing treatment and then carburized by passing hydrogen, saturated with pure n-heptane vapor at 0°C, over the specimens at 730°C. The specimens were then homogenized at 730°C for 2 hr in dry hydrogen. After the carburizing treatment the specimens were given the same vacuum anneal as for the decarburized specimens. The carbon content was determined from the maximum value of the internal friction carbon peak.2 Apparatus Fig. 1 shows a diagram of the tensile apparatus, with half the cooling coil removed. The cooling coil enabled temperatures from 200" to 77.2oK to be obtained. The apparatus was designed to fit a standard Tinius Olsen Universal tensile machine. The apparatus consisted of the rigid plate A which carried two carefully machined hooks H. These hooks attached the plate firmly to the moving crosshead of the tensile machine. The lower grip B was rigidly suspended from the plate A by three stainless steel rods. The upper grip C was joined to the upper grip of the tensile machine by the stainless steel rod E. The lower part of the apparatus was surrounded by a Dewar vessel, which was made a sliding fit inside the brass collar D. The specimen was held in a clamp which fitted into the grip, forming a ball and socket joint (see inset a). This was to attain as nearly pure

Jan 1, 1954

By Gilbert E. Doan

IN a technical civilization, that is. one whose major difference from past civilizations is its enormous development of technology, in transportation, communication, labor saving, centralized control, and mass production, it is natural that the most critical problems should be those that arise out of technologic advances; it is natural also that a. man who understands these advances should be chosen as the leader to meet these problems. This was done in the selection of Herbert Hoover as President of the United States. Mr. Hoover was a good, and perhaps a great President. But he was not a great politician and that ensured his defeat when a crisis came.

Jan 1, 1939

||Abad, Leopoldo F., Min Engr, Div of Mines, Bureau of Science Manila, P I '23 Abadilla, Quirico A, Geol, Lago Pet Corp Box 172, Maracaibo, Venezuela '20 ||Abbey, Robert Graham, The W W Sly Mfg Co Train Ave, Cleveland, Ohio '21 Abbott, A. N., Mines Supt, Mazapil Copper Co, Ltd Concepcion del Oro, Mexico '23 Abbott, Clarence E., Mgr, Mines & Quarries, Tenn Coal, Iron & R R Co, 1242 Brown Marx Bldg, Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr , Consolidation Coal Co , Elkhorn Div Jenkins, Ky. '16 Abbott, Robert R., Met Engr , Peerless Motor Car Co Cleveland, Ohio '12 ||Abbott, Wells Osborn, Ray Consolidated Copper Co Hayden, Ariz. '23 Abeel, George H, Jr., Cons Min Engr 4612 West 17th St , Los Angeles, Cal '18 Abel, Albert E., Asst to Pres, Valley Mould & Iron Corp Sharpsville, Pa. '19 Abernathy, George Elmer, Prof of Geol & Min , Kansas State Teachers College, Pittsburg, Kans. '20 Abey, Hiroshi, Min & Met Engr, Min & Met Dept, The Higher Technical School, Osaka, Japan. '17 ||d'Ablaing, Philip R, Chem , Anaconda Copper Min Co Great Falls, Mont '25 Aborn, Robert H , Research Assoc., Mass Inst of Tech Cambridge, Mass '19 Abouchar, Sylvain Sley, Min. Engi & Geol , care of S H Sekaly, 13 Rue El Nimr, Cairo, Egypt '17

Jan 1, 1923

By Howard H. Fields

Any mining engineer with a desire to operate independently, with some financial backing, and with no fear of heavy responsibility and long hours, should be able to make a comfortable living in Mexico. Barring a few inconveniences such as a lack of satisfactory liability or accident insurance, the difficulty of obtaining repair parts or vehicles, and the length of time required to receive returns from shipments, the operation of small mine is not at all difficult. It is, in fact, a little easier to find a good prospect in Mexico than in the U.S.

Jan 1, 1950

By William F. Boericke

THE Christy Creek clay mine of the General Refractories Co., in the Olive Hill District, ranks with the most important producers in the north-eastern Kentucky fire clay field, both from production of high-grade flint clay, as well as unusual extent and thickness of deposit. The property is but one of a number controlled by the General Refractories Co. in this district, but is given first consideration among them by the operating staff. Its total area is over 5000 acres, owned in fee or by lease of clay mining rights, and although mining operations have been in progress for over five years, scarcely one per cent of the ground has been worked as yet. The mine is near the southwestern end of the clay field, which extends in a belt 12 miles wide and 55 miles long, in a southwestern direction from Kenova, W. Va., which, as the name indicates, is at the junction of Kentucky, Ohio, and West Virginia. Olive Hill, where there is one of the l1Ulin plants of the General Refractories Co., and to which the clay from the mine is shipped, is about 26 miles distant from the mine. Connection is made with the Chesapeake & Ohio R. R. by a spur line . 8 miles in length, owned and operated by the company.

Jan 1, 1929

By L. E. Young

IT has been said the British Empire was built on British Coal. In all the postwar planning for Great Britain the necessity for producing cheap coal and the prosperity of the coal industry are given first consideration. On Jan. 23, 1945, there was released in London a "Report to the Colliery Owners" which had been awaited with great interest. This was entitled "A Plan for Coal" and was the recommendation of Robert Foot, chairman of The Mining Association (Colliery Owners), prepared at their request. Presentation of the "Plan" at this time is particularly significant as it is an answer to the demand for nationalization of the coal industry by the Labour Party and at the same time is a carefully considered program for postwar reconstruction, prosperity, and stability. In the words of Mr. Foot, If the coal industry for the first ten years after this war is to find itself in a situation similar to the one it occupied for the ten years following the last war, with its record of disputes, strikes, stoppages, short-time working, unemployment, and, with it all, a completely insufficient margin of profit, and all the insecurity and instability in our basic industry that was brought with them, it is goodbye to any real prospect of full employment, social security, and high standard of living. To present an elaborate review of the conditions which have brought to a crisis the unfortunate situation in the British coal industry is here unnecessary, but certain of the salient points

Jan 1, 1945

By A. B. Kinzel

ALTHOUGH the iron-carbon diagram has undergone many changes in the last 20 years, the region below the eutectoid line and up to approxi-mately 1.7 per cent carbon has been little affected. This region is generally considered to consist of cementite and ferrite. Graphite has been noted occasionally in the hypereutectoid steel region, and the ready formation of graphite nodules in malleable cast iron is a phenomenon difficult to interpret in the light of cementite, supposedly stable at sub-eutectoid temperatures. In this case the graphite formation has been partly explained by the presence of silicon, and many have believed that silicon acts to change the stable state rather than to accelerate reactions so as to arrive at the stable state in a briefer period of time. Consider-ation of this phenomenon indicates that cementite is not the stable phase in the temperature composition zone referred to. In the course of examining a low-carbon steel tube taken from a petroleum cracking still, which had been in service for approximately three years at temperatures somewhat below the eutectoid temperature, observations were made that shed light on this entire subject. The tube in question analyzed:1 C, 0.15 per cent; Mn, 0.49; Si, 0.02; S, 0.023; P, 0.015. The microstructure of the tube after service is shown in Figs. 1 and 2. From these it is evident that cementite as such is absent, and that in its place nodular graphite has been formed. In order to check this observation further, samples taken from the tube were heated at 850° C. for varying periods of time. The small samples were put into a large hot furnace, and the total time is recorded. The structure of the

Jan 1, 1934

By L. Bombardieri, H. F. Mills

IRON KING mine, producing gold-silver-lead-zinc ore, is 10 miles east of Prescott, Ariz. At present the 1806 level is being developed. The echelon pattern of ore deposit continues at depth but is less pronounced, and the orebody is now more or less continuous over 2600 ft of strike length. with widths 5 ft to as high as 26 ft where overlapping of lenses occurs in one section of the mine. Better continuity of ore at depth has encouraged systematic mining and improved plant facilities to offset higher operating costs. With favorable persistence of ore at depth. the three-compartment No. 6 hoisting shaft appeared inadequate to handle increased tonnage from greater depths, and in 1952, a four-compartment steel and concrete shaft was started. This is now at a depth of 1906 ft, and shaft pockets and loading cartridges are being installed on the 1806 level. Ore from the new shaft, hoisted in 51/2 -ton Jeto bottom dump skips, is dumped into a 500-ton shaft bin, from which it is fed to a 16x30-in. gyratory crusher and conveyed 415 ft through an undersurface concrete gallery to the secondary crusher and conveying system supplying the 900-ton mill. Lead, zinc, and pyrite concentrates are floated, and the flotation tailings are cyanided after desliming. Waste from the new shaft is dumped into a 250-ton surge bin, fed from this bin to a 24-in. conveyor, and discharged into the glory hole above the block cave. The new shaft is served by a double-drum 400-hp hoist used for ore and waste; the No. 6 shaft conveys men and material To secure a cheap source of waste fill for stoping operations, a block cave area was undercut In the hanging wall near the north end of the mine above the 600 level. Waste from the block cave is drawn from any of three large drawpoints on the 600 level, and a series of hanging wall transfer raises with controls and bypasses on each level provide a fast low-cost material for fill. The block cave is worked vertically through to surface in the form of a steep-sided hole 350x250 ft and several hundred feet deep, the sides of which cave and provide fill material without any blasting. Fill is a mixture of caliche-cemented surface gravel and small particles of hanging wall schist. Level Development: An orebody 300 times as long as it is wide requires a lot of development work. Former practice consisted of driving a haulage drift about 30 ft from the ore in an andesitic footwall, a drift on the ore, and crosscuts from the haulage drift at 100-ft intervals. Crosscuts are about 90 ft long. At present, only the odd numbered levels are so developed, and on the even numbered levels only the haulage drift and crosscuts are driven. Little or no timber is used for this development. This change resulted in 20 pct reduction of development costs and 50 pet reduction of square set stoping required for removal of floor pillars. Elimination of ore drifts on alternate levels leaves

Jan 1, 1957

THE first session was held in the small hall of the Academy of Music, on Tuesday evening, February 18th, 1879. The proceedings were opened by the reading, by President Eckley B. Coxe, of the following Address : SECONDARY TECHNICAL EDUCATION. Technical education is a subject to which both the American Institute of Mining Engineers and the American Society of Civil Engineers have of late years given much attention, and deservedly so. We all remember the admirable address of our former President, Mr. Holley, at the Washington meeting, upon this subject, and the very interesting reunion of the two societies in Philadelphia for its discussion. The problem to the solution of which the meeting devoted its attention was, "Shall the practical education of the engineer in the mine, in the rolling-mill, in the workshop, or in the field, precede, be contemporaneous with, or follow his theoretical studies in the technical school ?" I do not propose to add anything to what was so admirably said by so many of our leading engineers on that occasion ; but I shall ask your attention to another question in technical education, which seems to me equally worthy of our consideration, and which, I am sorry to say, has as yet attracted but little attention in this country. It is, "Shall the apprentices (I call them so for the want of a better general name), who are growing up and learning their trades in and around our mines and works, and from whose ranks the master mechanics and foremen of the future must be taken-shall they be provided with some means of obtaining as much theoretical training as may be necessary to enable them properly to understand the various processes and operations that they may be called upon to superintend, and not be obliged to pick up, as best they may, here a little and there a little truth mingled with much error?" In the former case, those who have the ability and industry to avail themselves of the advantages that should be offered to them would fit themselves to become real foremen, men who would understand and appreciate the true engineer and his methods. Of late years the young men of this country who have wished to enter our profession have had great facilities offered to them for so doing ; there have been undoubtedly great improvements in the methods of instruction; and although I am very far from imagining that no further progress can be made, or is demanded, yet I feel sure that

Jan 1, 1879

Jan 1, 1879

By R. B. Walker, R. Palmer, L. C. Bryner

The purpose of this investigation was to further study some of the factors affecting the air oxidation of sulfide minerals. Data obtained from laboratory studies on the effect of temperature, concentration of iron salts, pH, and other catalysts on the biological and nonbiological oxidation of sulfide minerals are presented. The oxidation of copper sulfide minerals and subsequent leaching of the soluble copper has long been a profitable operation. The chief oxidizing agent is oxygen from the air. This reaction is influenced by a number of different factors such as temperature, light, hydrogen ion concentration, oxidizing agents, and various catalysts. Sullivan1 found that copper sulfide minerals are slowly oxidized by the air and that dilute sulfuric acid and iron (111) increased their solubility. At that time it was not known that bacteria were involved in the oxidation of the sulfide minerals. It has been shown that pyrite, molybdenite, free sulfur, and the copper sulfide minerals found in the waste rock dumps in Bingham Canyon, Utah, are largely oxidized by chemosynthetic autotrophic microorganisms found in the leaching streams.2-6 Similar organisms have been isolated in other mining areas7,8 and from the effluents from coal rnines.9 The following are some of the questions that have arisen regarding the mechanisms of the reactions involved in the leaching process. How dependent is the leaching operation upon the biological reactions? How does the temperature effect the biological and non-biological reactions? How does the concentration of iron (II) and (111) effect the rate of oxidation of copper (II) sulfide? Does the iron act as a catalyst? Does activated carbon act as a catalyst on the oxidation of sulfide minerals? What effect does the hydrogen ion concentration (pH) have on the above reactions? The purpose of this paper is to report the results of laboratory studies on these problems. EXPERIMENTAL The apparatus used in this investigation was an air lift percolator described in our earlier work.' The percolator consisted essentially of an air lift which enabled the leaching solution and microorganisms to pass freely through a suspension of mineral (substrate) in Ottawa sand. The air lift served the additional purpose of maintaining an ample concentration of oxygen and carbon dioxide in the nutrient (leaching) solution. (See Fig. 1.) The percolators were so constructed that they could be immersed in liquid constant temperature baths for temperature studies. The thermostats were controlled to +0.5°C. The reactions were all run in the dark. The percolators were charged with one to three g of mineral, dispersed in 100 g of Ottawa sand and 100 ml of nutrient or leaching solution. The sand was purified to remove traces of iron by digesting with concentrated hydrochloric acid and washng with distilled water until free from chloride. After drying, the sand was ready for use. The compressed air supply was regulated to 5 psi and bubbled through an aerator containing distilled water, which was maintained at the same temperature as the bath used. The air was filtered through cotton plugs to maintain sterile conditions. The tops of the

Jan 1, 1968

By NEWTON B. KNOX

THE Guianas region is a geological unit, consisting of the northern lobe of the Brazilian Shield, but political accident and the fact that rivers act as the principal means of transportation have divided the region between five separate sovereignties. Brazilian and Venezuelan Guiana have already been considered. The French, Dutch, and British colonies consist of a coastal plain some fifty miles wide, which, together with the lower reaches of the principal rivers, support the greater part of the population. Inland from this tidewater region is a wide area of low, forest-covered hills, under-lain by gneisses, schists, granites, and pegmatites of the Shield. As in Venezuelan Guiana, these rocks are overlain by a thick series of horizontal continental sediments intruded by moderately basic magmas. Gold, bauxite and diamonds have been the principal products of the colonies. The first metal is quite widespread in the hill country. The quartz mines are small, though occasionally rich; probably the greater number of veins remain undiscovered because of the thick mantle of decomposition product that covers the schists and gneisses. The greater proportion of the gold, therefore, is derived from placers which are exploited in all three colonies. Some geologists claim that they occur in two belts parallel to the coast; whether this feature has its origin in the location of the primary mineralization or in the gradients of the rivers is not clear. In some instances the river gravels grade into auriferous laterite. The laterites are well developed in the Guianas and represent the weathering products of the more basic rocks.

Jan 1, 1946

By R. K. Govila, E. H. Parkison

THE interplanar angles for hcp metals vary with c/a ratio, and therefore must be computed separately for each particular metal or alloy. Manual computation of these angles is laborious and time consuming, and for this reason computer programs have been developed to accomplish this task.1"3 However, these programs have certain disadvantages. For example, they require prior knowledge and understanding of ALGOL or FORTRAN languages. Further, they will not print out specific angles but instead give all angles between given limits—thus program2 prints out a total of 26,649 angles between planes with indices and in the range from (4 4 4) to (4 4 4) for any given c/a ratio. The purpose of this note is to present a simple and inexpensive computer program for accomplishing this task. This program is written in BASIC language4 which does not require any prior knowledge of computer programming, and is ideally suited for nonprofessional programmers. It also provides flexibility for the user by allowing him to select any indices for as many or few planes as desired for any given c/a ratio. The computer program proposed below is based on the relationship in which + is the angle between any two planes and . TO illustrate use of the program, consider the problem of calculating the interplanar an-

Jan 1, 1970

By Alfred Boyles

"HEREDITY"' in cast iron has been a subject of much discussion. Numerous experimenters have found that the properties of gray iron may vary greatly without corresponding variations in composition or thermal treatment. The main structural difference in such cases is in the size and distribution of the graphite flakes and the explanations given usually attribute this difference to some chemical element not shown by ordinary analysis or to some physical factor, such as inclusions in the melt. It cannot be said that any of these theories is completely satisfactory. Much remains to be learned about cast iron and for this reason a study of the material was undertaken as a part of the program of fundamental research at Battelle Memorial Institute. A review of the literature indicated that very little systematic work had been done on the mecha-nism of freezing in cast iron. The experiments described below are largely concerned with that problem.

Jan 1, 1937

By Thomas T. Read

THE official title of our topic for today is "Resources of Metals and Other Strategic Minerals," but in accepting the invitation to open this discussion I claimed the privilege of being allowed to talk about problems other than resources for the two reasons that a great deal has already been said about resources and because we can never discuss them with the degree of certainty that an engineer likes. Resources are uncertain for many, reasons. One is that we do not know what is in the earth. It is four thousand miles to its center and although oil wells 1 ½ miles deep are becoming common and engineers are now talking of drilling holes 2 miles deep, even when they do they will have advanced only one two-thousandth part of the total distance. Only a relatively few mines are over a mile deep as yet. We know certainly that it is comparatively expensive to work at such great depth, but it would be a very foolish man who would assert it will be' impossible, one or two hundred years from now, for engineers to obtain from great depths mineral supplies that are now being obtained at or near the surface. As long as- I can remember I have been hearing that our petroleum resources were in imminent danger of speedy exhaustion, and yet the yearly output is now of the same order of magnitude as the total resources were once estimated, with ' the cry of over-production the loudest it has ever been. Tapping progressively deeper and deeper sources of supply, has produced this result. Even in the thin layer that we are now working much-exploration still remains to be done. .

Jan 1, 1929

By AIME AIME

BY the end of 1943, the United States will be able to produce aluminum at a rate of 1,150,000 tons a year. How much aluminum is 1,150,000 tons? It is sufficient to replace every railroad passenger car in this country three times a year. Or, it would put a thirty-piece aluminum cooking utensil set in every one of America's 34,000,000 homes with enough metal left over to make 5,000,000 miles of aluminum transmission cable, such as was used in the electrification of much of rural America. Expansion of aluminum production capacity for the war program has occurred in three steps: (1) expansion by private industry; (2) the letting of contracts by the Defense Plant Corp. for the construction of additional aluminum plants which may remain after the war to compete with existing facilities; and (3) the more recently announced D.P.C. program for the building of emergency plants to make aluminum, using stand-by power available in large metropolitan centers power of relatively higher cost, making it questionable whether such plants, now gravely needed, will be able to compete in a peacetime economy.

Jan 1, 1943

By M. Marciano, K. Kreider

Silicon carbide coated boron fiber (Borsic) reinforced aluminum composites were made which exhibit strength and modulus values predicted by the rule of mixtures. A successful technique for fabricating these composites consists of plasma spraying of monolayer filament reinforced tapes and subsequent diffusion bonding of these tapes into composites. The elastic properties of the composites were given by the rule of mixtures in reinforced directions. (The modulus parallel to the fibers was 32 x 106 psi for a composite with 50 pct by volume fibers. The other elastic properties for a composite with 50 pct fiber were transverse modulus = 14 to 16 X 10 psi, G = 9.5 x 106psi, and v,, = 0.23. Tensile strengths of over 190,000 psi were measured for the composites with 50 pct fiber and the average strength for these composites was 162,000 psi. These same composites had interlaminar shear strengths of 12 to 15,000 psi. Multidirectionally reinforced composites demonstrated the same reinforcement efficiency in strength and modulus as the uni-directimlly reinforced composites. Comrpessive strengths of composites with 50 pct by volume fiber were found to be greater than 250,000 psi. STRUCTURAL filamentary composite materials are being considered for use where high strength, high modulus, and lightweight materials are required. Metal matrix composites have been considered for use at temperatures ranging from cryogenic (aluminum stainless steel) to 6000°F (plasma sprayed tungsten plus tungsten fiber) and other requirements have been similarly diverse. Metal matrix composites offer high modulus and high strength in unreinforced directions, the ability to be joined by brazing or welding, and greater fracture toughness compared with the more easily fabricated resin matrix composites. This paper deals with the mechanical properties of aluminum boron composites, a system which is being considered for applications where lightweight, high modulus, and high strength are required at temperatures including those above the normal operating temperatures of resin composites. The boron fiber used in this investigation had an average room temperature strength of greater than 400,000 psi, a modulus of 58 x 106 psi, and a density of 0.09 lb per cu in. (2.6 g per cu cm).' The fiber used in the composites had a coating of silicon carbide to retard degrading reactions with the matrix at elevated temperatures. The coated fiber, which is sold commercially as Borsic: has been reported to have excellent resistance to degradation at temperatures up to 600°C in air and in aluminum2 and the same mechanical properties as the standard bare boron fiber. Fabrication of Composites. The composites were diffusion bonded from plasma sprayed monolayer tapes. These tapes were fabricated on a substrate of aluminum alloy foil which is incorporated in the composite matrix. The technique consists of winding a layer of fiber on the foil, and plasma spraying the balance of the matrix alloy over the windings which bonds all of the components together. Advantages of this process include the ability to achieve good fiber spacing, Fig. 1, the formation of a good bond between fiber and matrix (achieved during the plasma spraying), and the adaptability of the process for forming large and complex parts. This is particularly true when used with brazing foil backing which alloys low pressure bonding of the structural shape. PROPERTY EVALUATION TECHNIQUES Tensile test specimens, 5 to 7 in. long with a reduced gage section and ,030 to ,040 in. thick, were cut from composite sheets with a diamond saw. The gage section was .200 in. wide, while the gripped section was .240 in. wide and over 2 in. long in each grip. The standard gage length used was 1 in., however, transverse specimens (i.e., specimens with the fibers oriented 90 deg to the loading axis) were tested without a reduced section. Twelve specimens were also made with a 3-in. gage length but no significant effect of gage length was measured. The tensile test specimens were mounted in a fixture and aligned in friction grips using a 10X microscope. Unbonded foil doublers (0.010-in.-thick aluminum) were used to insure firm gripping with a minimum of damage to the fibers. The test specimens were transferred to the testing machine in a rigid fixture and mounted in the self aligning loading train. Testing was performed using a Tinius Olsen four screw testing machine with a torsion bar LVDT load

Jan 1, 1970

By C. F. Jenkins, G. V. Smith

Serrated plastic flow in stable austenitic alloys based on Fe/Ni has been shown to be related to the presence of carbon and/or chromium in the systems. Strength peaks and plateaus in the serrated-flow temperature region for a commercial alloy correlate with an increased dislocation content, arising, presumably, from enhanced multiplication as a result of a strong interaction between dislocations and solute atoms. The data generally support a mechanism controlled by migration of vacancies, with the energy for vacancy motion being modified by the presence of chromium. Chromium atom -dislocation interaction is responsible for effects above 500°C, whereas the defect interacting with dislocations between 200" and 500°C is suggested to be a carbon-vacancy Pair. ThE phenomenon of jerky flow, serrated flow, or the Portevin-le Chatelier (P-C) effect in austenitic stainless steels is usually attributed to substitutional at1,2 mospheres1,2 or to precipitates&apos;-4 which form at dislocations during plastic deformation. On the other hand, evidence exists which supports a direct inter-stitial-dislocation interaction mechanism for serrated flow in fcc Ni-C,5,6 Ni-H7-9 and in nickel-austenites containing carbon." The present work consists in a study of serrated plastic flow in stable austenitic al-loys. The effects of carbon and of chromium were investigated separately, and a commercial stainless steel with different levels of interstitial impurity concentration was studied in an attempt to delineate the combined effects of the alloying elements. EXPERIMENTAL TECHNIQUES a) Materials and Fabrication. A commercial AISI 330 stainless steel and several specially prepared aus-tenitic alloys have been studied. The experimental alloys were prepared by arc melting the constituents under purified argon. Analyses of the materials are given in Table I. The commercial alloy was obtained as 5/8 in. bar stock and rolled to 0.092 in. sq, with several intermediate anneals. At this stage some of the material was annealed in Pd-purified hydrogen at 1100°C to establish different levels of interstitial content. All other heat treatments were in vacuum (10-5 torr). The "pure" alloy ingots were swaged to 0.120-in. rod and annealed in Pd-purified hydrogen at 1100°C. The analyses for these conditions are also contained in Table I. Following the above treatment, the final wire sizes Table I. Chemical Analyses of Test Materials Hrin Hydrogen at Cr, Ni, Alloy 1lOO°C wt pct wt pct C, ppm* N, ppm* Type 330 As-received 14.78 33.25 430 300 Type 330 64 14.78 33.25 40 50 Type 330 200 14.78 33.25 27 21 Fe/35 Ni 72 - 35.10 <10 62 Fe/35 Ni 200 35.10 <I0 44 Fe/35 Nil15 Cr 72 14.95 34.94 <I0 61 Fe/35 Ni/15Cr 200 14.95 34.94 <10 45 Fe/35 Ni/C $ 35.OM 380 *Sensitivity: N t 5 ppm Ct10ppm. f Nominal Ni content. % A master NiC alloy was used in preparation of this material; courtesy of D.E. Sonon. were obtained by either swaging or cold drawing. The test results did not vary with these techniques. b) Specimen Preparation. Two sizes of specimen and two gripping systems were used. i) 0.070-in. wire with a chemically milled gage section: 0.75 in. long, 0.060 in. in diam. These were fastened into grips containing tapped grooves. ii) 0.050 in. wire, gage length 1.5 in. Ball bearings were welded to the ends of the wires and the gage length was taken to include all material between the welds. Socket-type grips were used with these specimens. With specimens of type ii), joining was performed in a specially constructed brass jig, under argon, and automatic timing was utilized in the procedure. No adverse effects of welding were noted. Specimens were encapsulated and solution treated for 1 hr at temperatures selected to produce the same average grain size, -50 µ. Annealing twin boundaries as well as normal crystal boundaries were counted. The temperatures used are listed in Table 11. Table 11. Specimen Size. Temperature of Heat Treatment and Resulting Grain Diameters for Test Materials Recrystallization Resulting Material Condition Temperature Grain Sue AISI 330 Not H purified 0.070 120O°C 45 to 55µ in, wire AlSl 330 H , pure, 0.070 in. 1150°C 45to55µ wire Fc/35Nil15Cr Pure, 0.070 in. wire 1000°C 45tossp Fe/Ni Pure. 0.070 in. wire 775°C 45 to 55µ Fe/Ni/C Pure, 0.050 in. wire 850°C 10 to 20p AlSl 330 Not purified, 0.050 1150CC 45to55p in. wire AlSl 330 ti, pure, 0.050 in. 1150°C 45to55p wire

Jan 1, 1970