Search Documents

By P. W. George

This paper presents geological data regarding deposits of over 7,500,000 tons of fine-grained sulphide ore in barite gangue. A series of pyroclastics and arkoses was intruded by sills of quartz porphyry in connection with batholithic intrusions of granite 3 miles from Buchans. Gentle folding, with fracturing and shearing of tuff beds and intruded quartz porphyry, accompanied and followed the intrusion of granite and porphyry. The sulphide-barite mineralization is localized primarily in fractured and sheared tuff beds, but also in the sheared quartz porphyry. Two structures have proved particularly favorable for mineralization—one, the center of an anticline; the other, a series of weak, incompetent tuff beds intruded by thin sills of quartz porphyry and located between strong beds of arkose. During the folding the weak tuff with intruded quartz porphyry was intensely sheared and contorted and subsequently mineralized by sulphides and barite. Introduction Buchans is 5 miles north of Red Indian Lake, in Central Newfoundland, at an elevation of 900 ft. above sea level and 400 ft. above Red Indian Lake, and is reached by a 37-mile private railway from Miller-town Junction. The first ore body found at Buchans was discovered some 30 years ago in the bed of Buchans River, by Matty Mitchell, an Indian woodsman employed by the Anglo-Newfoundland Development Co. Ltd. In the years following the discovery the ore was developed by shaft-sinking and drifting, with results indicating a lenticular ore body in a shear zone, containing about 100,000 tons of extremely fine-grained sulphide ore in barite gangue averaging about 0.05 oz. Au, 4 oz. Ag, 1.5 per cent Cu, 10 per cent Pb, 18 per cent Zn. Because a profitable metallurgical treatment for the ore was not found, the mine was closed down in 1911. In 1915, Mr. H. A. Guess, Vice President of the American Smelting & Refining Co., learned of the Buchans River ore body, and after metallurgical tests had been carried on from time to time in his company's testing plant a satisfactory separation of the sulphides by selective flotation was finally effected in 1925. Prospecting for additional ore bodies was begun in 1926, utilizing geophysical methods under the direction of Hans Lund-

Jan 1, 1937

By P. W. George

This paper presents geological data regarding deposits of over 7,500,000 tons of fine-grained sulphide ore in barite gangue. A series of pyroclastics and arkoses was intruded by sills of quartz porphyry in connection with batholithic intrusions of granite 3 miles from Buchans. Gentle folding, with fracturing and shearing of tuff beds and intruded quartz porphyry, accompanied and followed the intrusion of granite and porphyry. The sulphide-barite mineralization is localized primarily in fractured and sheared tuff beds, but also in the sheared quartz porphyry. Two structures have proved particularly favorable for mineralization-one, the center of an anticline; the other, a series of weak, incompetent tuff beds intruded by thin sills of quartz porphyry and located between strong beds of arkose. During the folding the weak tuff with intruded quartz porphyry was intensely sheared and contorted and subsequently mineralized by sulphides and barite. INTRODUCTION Buchans is 5 miles north of Red Indian Lake, in Central Newfound- land, at an elevation of 900 ft. above sea level and 400 ft. above Red Indian Lake, and is reached by a 37-mile private railway from Miller- town Junction. The first ore body found at Buchans was discovered some 30 years ago in the bed of Buchans River, by Matty Mitchell, an Indian woodsman employed by the Anglo-Newfoundland Development Co. Ltd. In the years following the discovery the ore was developed by shaft-sinking and drifting, with results indicating a lenticular ore body in a shear zone, containing about 100,000 tons of extremely fine-grained sulphide ore in barite gangue averaging about 0.05 oz. Au, 4 oz. Ag, 1.5 per cent Ch, 10 per cent Pb, 18 per cent Zn. Because a profitable metallurgical treatment for the ore was not found, the mine was closed down in 1911. In 1915, Mr. H. A. Guess, Vice President of the American Smelting & Refining Co., learned of the Buchans River ore body, and after metallurgical tests had been carried on from time to time in his company's testing plant a satisfactory separation of the sulphides by selective flotation was finally effected in 1925. Prospecting for additional ore bodies was begun in 1926, utilizing geophysical methods under the direction of Hans Lund-

Jan 1, 1937

By R. Shuttleworth, R. Smith

A Knudsen effusion tnethod I~as been used lo measure the vapor pressure of pure iron in the temperature range 1000° to 1500°C. Neutron-irradiated , natural iron was used and the Mn'~proclzdced by the (n, p) reaction removed by evaporation at high temperature. The results can be represented by the equation: where pM - 1.088 x 107 atm and T, = 20,890°K. A value of 100.2 kcal per g- atom was obtained for AH;. THE vapor pressure of pure iron in the temperature range 1000" to 1500°C has been measured. Radioactive iron and a Knudsen cell technique were used and the Mn' produced by an (n, p) reaction removed by evaporation at high temperature. From the variation of vapor pressure with temperature values of the enthalpy and entropy of solid iron have been found. Previous workers2 used a Lang-muir method and measurements were made over a smaller temperature range than that in this work. EXPERIMENTAL The apparatus used was similar to that of Pyle and Shuttleworth, and McLellan and Shuttle worth. However, because of the higher temperatures the Knudsen cell was machined from tungsten bar and the flanged furnace tube was beryllia. Heating was by passing a high current (70 amp at 7 v for 1500°K) through a strip of tantalum foil laid across the top of the cell and through a turn of molybdenum wire around the furnace tube. This method of heating ensured that the top of the cell was slightly hotter than the base and prevented condensation and re-evaporation from the orifice. The temperature was measured by means of a pt/Pt 13 pct Rh thermocouple spot-welded to the base of the crucible. To ensure accurate temperature measurement the iron was in the form of a thin disc (0.75 cm diam by 0.075 cm) which lay on the base of the cell. The high-purity iron was irradiated in the Harwell pile for a week at a neutron flux of 1.2 X 10" neutrons per sq cm per sec. The isotopes fe'~ and Fe" are produced by (n! y) reactions but only Fe", half-life 45.1 days, is a emitter; Mn which is also a y emitter, half-life 300 days, is produced simultaneously by an (n,p) reaction.' Immediately after irradiation of natural iron the ratio of ~e" to Mn y activity was 100:l. However, manganese is very much more volatile than iron and almost all the y activity of the condensate is due to Mn'~. Thus it was essential to eliminate all the manganeses before any measurement of the vapor pressure of iron was made and this was done by preliminary heating for 20 hr at 1400°C. For each determination the iron was dissolved from the target with acid and the y activity compared to a known weight of iron. By means of a y-ray spectrometer the y-activity measurements were made at the 1.09-mev peak of the 17e5' spectrum where the background was of the order of 3 cpm. Despite the low specific activity of ~e" a mass of 10- " g of iron could be determined corresponding to a vapor pressure of about l0-'' atm. RESULTS The vapor pressures were calculated from the equation: Where m is the mass of iron effusing in a time t through an orifice of area a2, r is the radius of the target, Z is the distance from the orifice to the

Jan 1, 1965

By G. F. Tagg

In an earlier paper1, the author described a method of interpreting earth-resistivity curves, based on the theoretical investigation of a single horizontal underlying stratum. If the four-electrode system of Wenner is employed, the resistivity in a homogeneous soil is given by the formula where a is the electrode separation and R is the resistance of the earth between the two inner electrodes. If the earth is not perfectly homogeneous, the application of this formula gives an apparent specific resistance varying with the electrode separation. In the special case of the single horizontal underlying stratum, there is a surface layer of thickness h and resistivity p1 and a lower layer, extending to infinity, of resistivity pz. It has been shown by Lancaster-Jones2 that the apparent resistivity obtained by an application of equation 1 is related to the true resistivities, the depth h and the electrode separation a by an expression of the formhere pa is the apparent resistivity and F is a function (actually an infinite series), of the ratio h/a, and a reflection coefficient k = (p2 — p1)/(p2 + p1). For given values of h/a and k, the right-hand side of equation 2 can be calculated, and curves drawn showing the relationship between pa/p1, h/a and k. Such a set of curves for the case when p1 > p2 is given in Fig. 1. When pl is less than pz it is more convenient to use conductivity instead of resistivity. Hence, if oa = the apparent conductivity = lip, and a1 = the conductivity of the upper layer = l/pl, it follows that GeophyGical prospecting by earth-resistivity methods is frequently applied to investigation of structural problems in geology. Fig. 1 indicates a scheme of the general arrangement used in these methods of measurements. The battery (or generator) E is connected with two "current electrodes" I1 and I2. The current of intensity J, supplied by this battery, passes through the earth between these elcc- trodes. A potential difference U will be measured between two other electrodes V1 and Vz, called "potential electrodes." According to the configuration of electrodes (Fig. I), the resistivity of a homogeneous soil results from the formula

Jan 1, 1940

By G. F. Tagg

In an earlier paper1, the author described a method of interpreting earth-resistivity curves, based on the theoretical investigation of a single horizontal underlying stratum. If the four-electrode system of Wenner is employed, the resistivity in a homogeneous soil is given by the formula where a is the electrode separation and R is the resistance of the earth between the two inner electrodes. If the earth is not perfectly homogeneous, the application of this formula gives an apparent specific resistance varying with the electrode separation. In the special case of the single horizontal underlying stratum, there is a surface layer of thickness h and resistivity p1 and a lower layer, extending to infinity, of resistivity pz. It has been shown by Lancaster-Jones2 that the apparent resistivity obtained by an application of equation 1 is related to the true resistivities, the depth h and the electrode separation a by an expression of the formhere pa is the apparent resistivity and F is a function (actually an infinite series), of the ratio h/a, and a reflection coefficient k = (p2 — p1)/(p2 + p1). For given values of h/a and k, the right-hand side of equation 2 can be calculated, and curves drawn showing the relationship between pa/p1, h/a and k. Such a set of curves for the case when p1 > p2 is given in Fig. 1. When pl is less than pz it is more convenient to use conductivity instead of resistivity. Hence, if oa = the apparent conductivity = lip, and a1 = the conductivity of the upper layer = l/pl, it follows that GeophyGical prospecting by earth-resistivity methods is frequently applied to investigation of structural problems in geology. Fig. 1 indicates a scheme of the general arrangement used in these methods of measurements. The battery (or generator) E is connected with two "current electrodes" I1 and I2. The current of intensity J, supplied by this battery, passes through the earth between these elcc- trodes. A potential difference U will be measured between two other electrodes V1 and Vz, called "potential electrodes." According to the configuration of electrodes (Fig. I), the resistivity of a homogeneous soil results from the formula

Jan 1, 1940

By G. A. Chadwick, D. Jaffrey

The morpho1ogies and orientation relationships of the phases in the Sn-Zn and A1-A13Ni eutectic systems were examined by electron microscopy and X-ray diffraction techniques. In each alloy the "transition" from the lamellar to the fibrous morphology was found to be one of scale, not of type. The minor phase in both systems exhibited certain well developed facets which were not affected by changes in the ingot solidification rate. The crystallographic relationships displayed by the pairs of phases in both systems were also insensitive to the growth rate. In the Sn-Zn alloy, the unique relationship of: growth direction - II [1201 Sn - II [01101 Zn and ribbon interface plane 11 (101) Sn 11 (7012) Zn was determined. The Al-Al3Ni alloy phases did not possess any particular orientation relationship, though the Al3Ni phase invariably grew in the [010] direction and exhibited the same set of facet planes. These results are discussed in relation to current eutectic growth theories and explanations of the "lamellar to fibrous transition". THE lamellar to fibrous transition that occurs in many eutectic alloys has been the subject of considerable speculation and experimental study. In some alloys it can be induced solely by an increase in the solidification rate,'-3 whereas in others the transition supposedly occurs only if the lamellae are forced to grow out of the overall ingot growth direction.4-6 he cause of this latter type of transition has been attributed to deviations of the lamellae from their low energy habit planes;4'5'7 fibers are produced because the sustaining force for lamellar growth (a low energy boundary) is destroyed. Implicit in these explanations is the assumption that fibers are circular in cross-section and completely lacking in low energy inter-phase interfaces. The "natural" growth rate dependent transition has been studied less thoroughly although Tiller8 has attempted a theoretical explanation of it. Tiller's arguments are not completely satisfactory9 but his suggestion that the relative undercoolings of the solid/liquid interface for lamellar and fibrous morphologies are growth rate dependent cannot be totally discounted; it is possible, for instance, that the relative interfacial undercoolings could alter and produce the observed morphology change if the orientation relationships between the phases and the associated interphase bound- ary energies were sensitive to growth rate. Salkind et al." have reported finding a change in the orientation relationships in the A1-A13Ni system accompanying the lamellar to fibrous transition, but contradictory evidence has also been reported for this3'" and another system,12 so the position remains unclear. In an attempt to clarify matters a study was made of the "lamellar to fibrous" transition in the Sn-Zn and A1-A13Ni eutectic systems; the morphologies of these two selected systems are quite similar when viewed by optical microscopy. In the present research the morphologies and morphology changes were investigated by electron microscopy. The orientation relationships existing between the eutectic phases were also determined for both morphologies in both eutectic systems. EXPERIMENTAL PROCEDURE The materials and method of alloy preparation and ingot solidification for the Sn-Zn system have been reported previously.2 In this investigation nine horizontally grown ingots of the highest purity (99.9997 pct) were used. The temperature gradient in the melt was not intentionally varied and was approximately 10°C per cm. Seven growth rates between 1.3 cm per hr and 20 cm per hr were imposed. The A1-A13Ni alloys were prepared from "Spec. Pure" nickel and 99.995 pct aluminum by melting the components in an open alumina crucible and casting the melt into the cold graphite mold. Six ingots of the Al-Al3Ni alloy were unidirectionally solidified at growth rates from 1 cm per hr to 12 cm per hr under high purity argon. A typical ingot was 20 cm long, 1 cm wide, and 0.75 cm to 1.5 cm thick. Samples taken from the bars at positions 12 cm from the nucleation end were examined by conventional orthogonal-section metallo-graphic techniques. When required, samples were mounted for X-ray diffraction analysis using the Laue back-reflection technique with a finely focussed X-ray source. The surfaces of the A1-A13Ni specimens were prepared by mechanically polishing them down to the 1 µ diamond pad stage followed by an electropolish in 80/20 methanol/perchloric acid solution at 0°C and 20 to 30 v. The Sn-Zn specimens were repeatedly polished on an alumina pad and etched in hot dilute (2 pct) nitric acid until the diffraction spots were found to be sharp. Thin films of the alloys were prepared for observation in an electron microscope by spark machining thin discs (0.03 to 0.04 in. thick) from longitudinal and lateral sections of the bars and elec-trolytically thinning them via a jet polishing technique. For the A1-A13Ni eutectic alloy, an 80/20 mixture of ethanol/perchloric acid at 40 v and 20°C was found to be satisfactory. A solution of 70/20/10 methanol/perchloric acid/butylcellosolve at 25 v and 20°C was used on the Sn-Zn alloy. For the former alloy the jet nozzles (cathodes) and the disc clamps were of aluminum;

Jan 1, 1970

By E. S. Machlin, A. A. Hendrickson

Use was made of a recently developed surface-accumulation diffusion technique to measure the self-diffusivity of edge-type dislocation singular lines (Burgers vector along <110>) in a bent and polygonized single crystal of silver. Two factors are involved in obtaining a number for the diffusivity. One factor, the dislocation-line density, was measured by a microscopic technique recently developed, and the value of the other parameter, the effective "diameter" of a dislocation pipe, was estimated. With these parameters equal to 7.3 X 106 dislocations per sq cm and 10-7 cm, respectively, it was found that the self-diffusivity along edge-type dislocation lines was a factor of about two times the average grain-boundary self-diffusivity. The dislocation-pipe diffusivity is about 7x10-7 sq cm per sec at 450°C. THE possibility of short-circuit diffusion through imperfections in crystals has been recognized for some time. It was only recently, however, that concerted effort has been expended to obtain values of diffusivity for grain-boundary short circuits. The work, for example, of Hoffman and Turnbull1 on silver, Fisher&apos;s&apos; analysis of the grain-boundary dif-

Jan 1, 1955

By D. W. Rudd, D. W. Vose, S. Johnson

The permeability of Mo-0.5 pel Ti to hydrogen was investigated over a limited range of temperature and pressuire (709° to 1100°C, 1.i and 2.0 atm). The resulting permeability, p, is found to obey the The experimental data justifies the permeation mechanism as a diffusion contl-olled pnssage of Ilvdrogen atoms through the metal barrier. 1 HE permeability of metals to hydrogen has been investigated by a number of workers and their published results have been tabulated by Barrer&apos; up to 1951. Since most of the work on the permeability has been accomplished prior to this date, the compilation is fairly complete. Mathematical discussion of the permeability process has been reported by Barrer, smithells, and more recently by zener. From these efforts several facts are observed. First, the permeability of metals to diatomic gases involves the passage through the metal of individual atoms of the permeating gas. This is evidenced by the fact that the rate of permeation is directly proportional to the square root of the gas pressure. Second, the gas permeates the lattice of the metal and not along grain boundaries. It was shown by Smithells and Ransley that the rate of permeation through single-crystal iron was the same after the iron had been recrystallized into several smaller crystals. Third, it has been observed that the rate of permeation is inversely proportional to the thickness of the metal membrane. Johnson and Larose5 verified these phenomena by measurirlg the permeation of oxygen through silver foils of various thicknesses. Similar findings were noted by Lombard6 for the system H-Ni and by Lewkonja and Baukloh7 for H-Fe. Finally, it has been determined that for a gas to permeate a metal, activated adsorption of the gas on the metal must take place. Rare gases are not adsorbed by metals, and attempts to measure permeabilities of these gases have proved futile. ~~der&apos; found negative results on the permeability of iron to argon. Also, Baukloh and Kayser found nickel impervious to helium, neon, argon, and krypton. From what was stated above concerning the dependence of the rate on the reciprocal thickness of the metal barrier, it is seen that although adsorption is a very important process, at least in determining whether permeation will or will not ensue, it is not the rate determining process for the common metals. A case in which adsorption is of sufficient inlportance to cause abnormal behavior has been noted in the case of Inconel-hydrogen and various stainless steels.&apos;&apos; APPARATUS The apparatus used in this study is shown in Fig. 1. The membrane is a thin disc (A), but is an integral part of an entire membrane assembly. The entire unit is one piece, being machined from a solid ingot of metal stock. When finished, the membrane assembly is about 5 in. long. Two membrane assemblies were made; the dimensions of the membranes are given in Table I. The wall thickness is large compared to the thickness of the membrane, being on the average in the ratio of 13 to 1. There exists in this design the possibility that some gas may diffuse around the corner section of the membrane where it joins the walls of the membrane assembly, If such an effect is present, it is of a small order of magnitude, as evidenced by the agreement of the values of permeability between the two membranes under the same temperature and pressure. A thermocouple well (B) is drilled to the vicinity of the membrane. The entire membrane assembly is then encased in an Inconel jacket and mounted in a resistance furnace. The interior of the jacket is connected to an auxiliary vacuum pump and is always kept evacuated so that the membrane assembly will suffer no oxidation at the temperatures at which measurements are taken. The advantages of this configuration are: 1) there are no welds about the membrane itself, so that the chance of welding material diffusing into the membrane at elevated temperatures is remote. 2) It is possible to maintain the membrane at a constant temperature. Since the resulting permeation rate is very dependent upon temperature, it is advisable to be as free as possible from all temperature gradients. 3) It is possible to obtain reproducible results using different specimens. The only disadvantage to this configuration is the welds (at C) in the hot zone. The welding of molybdenum to the degree of per-

Jan 1, 1962

R. Schuhmann, Jr. (Purdue University)— Fulton and Chipman&apos;s results on rate of silica reduction from slags are analogous in many was to the results of Parlee, Seagle, and Schuhmann10 on rate of alumina reduction from alumina crucibles. Both investigations have given comparably low rates of reduction and slow approaches to equilibrium. Accordingly, we may hypothesize that the rate-determining step is the same in both kinds of experiments; that is, oxygen diffusion across the stagnant boundary layer on the liquid-metal side of the interface between the liquid metal and the oxide phase (slag or solid oxide). I suggest that silica reduction involves the following consecutive steps: I) At the slag-metal interface: SiO2(slag) Si+ 20 II) Transport of oxygen from slag-metal to gas-metal interface: a) diffusion across liquid-metal boundary layer at slag-metal interface. b) convection within the body of liquid metal. c) diffusion across boundary layer at metal-gas interface. 111) At the metal-gas interface: C +O- CO (gas) Iv) At the graphite-metal interface: C (graphite) -C At steelmaking temperatures it is reasonable to assume that equilibrium is attained in all three chemical reactions (I, 111, and IV) right at the respective interfaces. Convection within the stirred liquid metal (step IIb) is also rapid. Transport of Si and C should be orders of magnitude easier than transport of 0, because of the relatively high concentrations of Si and C. Accordingly, we might expect the overall reaction rate to be determined by boundary-layer diffusion of oxygen, either IIa or IIc. Fulton and Chipman&apos;s demonstration that bubbling CO through the system had no major effect on reaction rate indicates that IIc is not the slowest step. Therefore, it becomes logical to estimate the maximum rate for step IIa and to compare this theoretical estimate with Fulton and Chipman&apos;s experimental data. If oxygen diffusion across the liquid metal boundary layer at the slag metal interface (step IIa) is rate-determining, In this equation, dn sio, /dt is the rate of silica reduction in moles per sec,A is the area of slag-metal interface in sq cm, Do is the diffusivity of oxygen in sq cm per sec, 6, is the boundary layer thickness in cm, c,* is the oxygen concentration right at the slag-metal interface in moles per cubic cm, and co is the oxygen concentration in the body of the liquid metal, also in moles per cubic cm. Equilibrium data" on the silicon deoxidation reaction in liquid iron and steel at 1600°C indicate that the oxygen contents of the liquid metal in Fulton and Chipman&apos;s experiments at 1600°C probably fell in the range of 0.5 x10-3 x10-3wt pct. That is, the maximum conceivable value of co*-co for the system under consideration was on the order of 10"5 mole oxygen per cubic cm. On the basis of previously published data,1O,11 it is estimated that Do/0 will fall somewhere in the range from 10-3 to 10-1 cm per sec. The surface area A in Fulton and Chipman&apos;s experiments was approximately 20 sq cm, and the weight of metal involved was about 500 grams. Combination of all these figures with the above rate equation leads to an estimate that the rate of silica reduction should fall within the range from 0.002 to 0.2 wt pct Si per hr. This estimate is consistent with the experimental data. For example, Fulton and Chipman&apos;s Fig. 2 shows a change of about 0.3 pct Si in 10 hr, corresponding to an average rate of 0.03 pct per hr. According to the proposed hypothesis, increasing the temperature will increase the reaction rate ill two ways: 1) by increasing oxygen diffusivity and 2) by increasing the oxygen concentration (oxygen solubility) in the liquid metal. The combination of these two effects accounts for the high value of the observed activation energy. Summarizing, I propose that the rate of silica reduction, like that of the carbon-oxygen reaction, is diffusion controlled and that low oxygen concentration in the liquid metal is the major factor accounting for the very low observed rates of silica reduction. John Chipman (author&apos;s reply)—The authors thank Professor Schuhmann for his interesting contribution. His proposed explanation may well prove to be the correct one. There is clearly a need for much further experimental work on this problem, and further research is in progress.

Jan 1, 1961

By M. T. Melvin, N. P. Kripakov

The practical application of a post-processing modeling procedure to simulate progressive rock failure around the periphery of coal mine entries is presented. This numerical scheme utilizes a simple rock model that incorporates easily obtainable input parameters consistent with basic rock mechanics principles. These parameters include the cohesion, angle of internal friction, modulus of elasticity, and Poisson&apos;s ratio of the bedded deposits that comprise the imediate roof, coal seam, and immediate floor. The geometry of the entry, along with the in situ stresses existing at a mine site prior to mining, are also considered in the analysis. The potential of this procedure as a predictive tool in determining the extent of pillar rib fracturing and yielding of the immediate roof and floor is evaluated assuming a Mohr- Coulomb failure criterion. The procedure is designed to be user oriented and is adaptable to any finite element code with linear elastic capability, making it particularly attractive to users with limited budgets and computer size.

Jan 1, 1983

By Oscar M. Wicken

The mineral magnesite (MgCO3) if pure would consist of 47.7 pct MgO and 52.3 pct CO2. It is one of the calcite group of rhombohedral carbonates which includes calcite (CaCO3), siderite (FeCO3), rhodocrosite (MnCO3), and smithsonite (ZnCO3) among others. The members of this group enter into a wide range of substitutional solid solutions, whose range is still imperfectly known.* MgCO3 and FeCO3 appear to form a complete series of which breunnerite (ferroan magnesite) is a well known variety. Because of the considerable difference in size of the Ca and Mg ions, there is only a limited range in substitution in the MgCO3-CaCO3 series. (Dolomite, not strictly a member of the calcite group, may be regarded as an ordered structure developed when Ca: Mg is approximately 1:1.) The practical consequence of these relationships is that the lime carbonates (calcite and dolomite) are commonly present in magnesite deposits chiefly as mechanical mixtures. Magnesite may be either crystalline or "amorphous" (cryptocrystalline). The crystalline form has a hardness of 3.5 to 4.0. The color may range from white to black through shades of yellow, blue, red or gray. It is rarely found pure but generally contains variable amounts of iron, lime, and silicate minerals. Color cannot be used as an index of purity except under specific local conditions in a single quarry. In a given quarry an experienced man may be able roughly to grade magnesite by intuitively assessing such features as crystallinity and color. Crystalline magnesite occurs in larger deposits, but the cryptocrystalline variety is more common. The latter is fine-grained and compact and shows no cleavage; often it is descriptively called "bone magnesite." The fracture is usually conchoidal, and hardness is 3.5 to 5.0. It is normally white, but sometimes it is light yellow to orange or buff because of included impurities. In addition to lime and iron, which may be present in small amounts, silica may be present as inclusions of serpentine, quartz, chalcedony, or other minerals. In general, commercial deposits of "amorphous" magnesite have lesser amounts of accessory minerals than does crystalline magnesite. The specific gravity of "amorphous" magnesite is 2.90 to 3.0. Pure, crystalline magnesite has a specific gravity of 3.02, but iron carbonate, commonly present, raises the specific gravity to somewhat higher values. Magnesite dissociates, when sufficiently heated, into magnesia (MgO) and carbon dioxide. Either simultaneously or upon further heating the magnesia develops a crystalline structure identical with that of the natural mineral, periclase, which occurs sparingly in nature but not normally in workable deposits. Brucite is another magnesium mineral capable of being directly reduced to magnesia by heat alone. Brucite (Mg(OH)2) has been mined for the production of various grades of magnesia. It theoretically contains 69.1 pct MgO and 30.9 pct H2O. It may be white, but is generally blue or green with a gray cast. It has a translucent appearance. The mineral is soft (hardness, 2.5), and has a specific gravity of about 2.4. Nomenclature of Products The word "magnesite" literally refers to the natural mineral, but common usage has applied it plus a prefatory word to two other

Jan 1, 1960

By H. T. Clark

NO previous determinations of the deformation or recrystallization textures of titanium or of titanium-base alloys have been reported in the literature. The room-temperature structure of titanium is hexagonal close-packed with a c/a ratio less than 1.633. It would be expected, therefore, to have a rolling texture similar to that of other hexagonal close-packed metals, namely (0001) [1010]. Burgers and Jacobs1 have shown that zirconium, a metal isomorphous with titanium in its structure and similar in many of its properties, has such a texture with a scatter of the basal plane toward the transverse direction. This scatter is in the opposite direction from that found in magnesium by Bakarian2 but similar to that reported by Smigelskas and Barrett3 or beryllium. The rolling and annealing textures reported here for high-purity iodide titanium are significantly different from the . textures of any other hexagonal close-packed metal. All titanium used during this investigation was prepared by the iodode process." The annealed hardness of this material varied from 73 (material used for sample No. 2) to 97 Vickers hardness number. An estimate of the chemical composition of this grade of titanium has been reported by Finlay and Snyder.5 With one exception, shown in table I, the as-deposited titanium was cast into 10 to 20 g ingots in an electric arc furnace in purified argon before being rolled to sheet. The cast ingots were forged and ground until their cross-section was approximately rectangular, annealed 1 hr at 700°C in vacuum and cold rolled. Rolling was carried out in a two-high, 4 in. diam mill, using reductions no greater than 10 pct per pass. The direction of rolling was reversed after each pass, and, in order to avoid temperature effects, the sheet was allowed to cool after each pass. Unless the rolled sheet was sufficiently thin for X-ray penetration (about 0.004 in.), it was reduced to this thickness by pickling. Because of the possibility of introducing twinning or other deformation during grinding, no attempt was made to maintain uniform thickness of the sample during pickling by intermediate grinding or sanding operations. Those samples to be used for determining the annealed texture were recrystallized by vacuum annealing the cold-rolled sheet for 1 hr at 500°C. These thin samples were held between thick titanium sheets during annealing to prevent distortion. Table I outlines the rolling and annealing schedule of those samples for which photograms or texture patterns are shown. X-ray Techniques The usual techniques for determining textures were employed during this work. Molybdenum radiation was used for the transmission exposures and copper radiation for the glancing angle ones. Since titanium fluoresces under these conditions, it is necessary to employ a filter between the sample and the film. The Kß radiation filters are very satisfactory for this purpose. Sufficient grains having favorable orientation were present in both the cold-worked and in the cold-worked—500°C annealed samples to provide satisfactory patterns with the samples stationary. Because of the difficulties of comparing intensities of transmission photograms with those obtained

Jan 1, 1951

By William Benzon

Bethlehem Steel&apos;s Cambria Division coal cleaning and preparation plant, operated by Bethlehem Mines Corp., is located in Cambria County, Pa., about 2 ½ miles southeast of Ebensburg. Here, above ground, is the most modern coal preparation plant in the world. Below the surface is a new coal mine also referred to as "the most modern that could be built today." The preparation plant has a capacity of 1370 tons of clean coal per hr. It serves three Bethlehem mines, Heisley No. 31, Revloc No. 32, and the new Cambria Slope No. 33.

Jan 12, 1965

By M. F. Smith

BELOW the nose of the bainitic C curves in isothermal transformation diagrams, the rate of the austenite-to-bainite transformation usually decreases with decreasing temperature. However, in some steels and iron-carbon alloys, there is a noticeable acceleration in the initial reaction rate at temperatures just above Ms. Such speeding-up of the bainitic transformation would be understandable at temperatures just below Ms because of the catalytic effect of the martensite formed,&apos; but the reversal in isothermal kinetics just above Ms seems quite anomalous. This behavior was observed by Howard and Cohen&apos; in a 1.35 pct C steel and, on the basis of metallo-graphic examination, it was attributed to the formation of a thin plate-like product not belonging in the bainitic sequence. More recently, schaaber2 found two-stage reactions occurring in the vicinity of Ms in a number of steels, and suggested that the first stage might be the isothermal formation of marten-site, preceding the isothermal formation of bainite in the second stage. A decrease in the bainitic incu-

Jan 1, 1960

By D. E. Thomas

Oxidation rate constants were determined for Cu-Pd and Cu-Pt alloys as a function of alloy composition and temperature. Reaction products were identified. Relationship between oxidation rate constants and diffusion constants in the reaction zones is discussed. THE mechanism of oxidation of alloys is consider--&apos;¦ ably more complex and not so well understood as that of pure metals. The oxidation of a one-phase binary alloy of which one component is a noble metal should logically be the simplest case of alloy oxidation, for in this case one is concerned presumably only with the oxidation of the base metal and the diffusion process by which it reaches the reaction site. This had led a number of investigators to study such systems. Probably the earliest work was that of Tammann and Rienacker&apos; on the tarnishing of Cu-Au alloys at temperatures up to 300°C. These alloys oxidize according to the logarithmic law, that is, the film thickness is proportional to the logarithm of the time. The rate of film formation was found to decrease with increasing gold content. Raub and Engel² investigated the oxidation of Au-Cu, Cu-Pd, Au-Ag-Cu, Au-Pd-Cu, and Ag-Pd-Cu alloys at 750°C in air. These alloy systems form a continuous series of solid solutions at the temperature of oxidation with the exception of those containing silver. Au-Cu alloys oxidize parabolically, the rate constant decreasing slowly with increasing gold content up to about 15 atomic pct* Au, and more rapidly thereafter. An alloy with 14 pct Cu forms only a very thin layer of CuO on the surface and probably also a subscale.† Alloys containing more than 14 pct Cu have scales consisting of CuO and subscales of Cu,O embedded in nearly pure gold. The Cu-Pd alloys obey the parabolic law except for slight deviations for alloys containing 53 and 84 pct Cu. The overall oxidation rate decreases rather smoothly with increasing palladium content. A scale consisting of a thin layer of CuO and a thick layer of Cu²O and a subscale of Cu²O embedded in nearly pure palladium was observed for alloys containing 84, 53, and 30 pct Cu. An alloy with 19 pct Cu formed only a subscale of CuO embedded in nearly pure palladium, and an 8 pct Cu alloy formed only a thin film which was presumed to be PdO. The ternary alloys considered by Raub and Engel oxidized in much the same way as did the binaries. Wagner and Grunewald³ found that Ni-Au alloys, oxidized at 900°C in oxygen, formed a scale of NiO and a subscale containing NiO and gold. The overall oxidation rate increases with increasing gold content, passes through a maximum and then decreases to zero for pure gold. The fact that gold increases the oxidation rate was attributed to "pores" in the scale. Kubaschewski&apos; investigated the air oxidation of alloys of platinum or gold with up to 10 pct Cu or Ni at temperatures in the range 300" to 1550°C. Parabolic behavior was noted for all alloys except Au-Ni, with rates decreasing in the order Au-Cu, Au-Ni, Pt-Ni, Pt-Cu. The diffusion coefficients for the latter three systems are known, and they decrease in the same order. However, activation energies for the oxidation of these alloys do not agree with the activation energies for diffusion in the respective alloy systems. Kubaschewski and Goldbeck7 nvestigated the oxidation of Ni-Pt alloys in air at temperatures of 600"

Jan 1, 1952

By R. D. Schoone, J. T. Michalak

Recovery, recrystallization, and texture development of a cold-rolled aluminum-killed steel have been studied during simulated box annealing. Two different initial conditions existed prior to cold rolling: 1) essentially all of the nitrogen in solid solution and 2) most of the nitrogen precipitated as AlN. The combined effect of nitrogen and aluminum in solid solution before annealing was to inhibit recovery and sub-grain growth at temperatures above about 1000°F and to raise the recrystallization temperature range on continuous heating at 40°F per hr from 1000"-1050°F to 1065"-1085°F. For the material with nitrogen and aluminum initially in solution there was an inhibition in the nucleation of the (001) [110] texture component and an enhancement of the (111) [110] texture component. The differences in annealing behavior mzd texture development are attributed to preprecipitation clustering of aluminum and nitrogen at subboundary sites developed by prior cold working. THE annealing of cold-worked aluminum-killed steels has been the subject of numerous investigations.&apos;-&apos;2 These studies have been concerned with kinetics of recrystallization, with microstructure and texture development, and with the individual and combined effects of composition, thermal history prior to cold rolling, and heating rates during subsequent annealing. It has been shown that the inhibition of recrystallization, and the development of the pancake-shaped grain and recrystallization texture characteristic of aluminum-killed steels, can be associated with the precipitation of A1N particles during a recrystallization anneal involving heating rates in the range 20" to 80°F per hr. If the AIN is precipitated before cold rolling or if more rapid heating rates are employed, the cold-rolled steels recrystallize more rapidly to an equiaxed grain structure and texture comparable to that of rimmed low-carbon steel. The retardation of recrystallization, the development of the elongated grain structure, and the pronounced (111) texture have been attributed to: 1) precipitation of A1N at prior cold-worked grain boundaries to form a mechanical barrier to grain boundary migration;&apos; 2) precipitation on the boundaries of the growing recrystal-lizing grains as well as on cold-worked grain boundaries;&apos;" and 3) preprecipitation clustering or precipitation on subboundaries to retard recovery, nucleation, and growth. The present study was undertaken to study in more detail recrystallization and texture development during commercial box annealing of cold-rolled aluminum-killed steels. Comparison of the annealing be- havior after cold rolling, for two different conditions prior to cold rolling, was made in an attempt to define more clearly the role of aluminum and nitrogen in forming the recrystallization texture. A) MATERIAL AND PROCEDURE The material used in this investigation was a commercial low-carbon aluminum-killed steel which was hot-rolled with a finishing temperature of about 1565"F, then coiled at about 1020°F. The composition, in wt pct, was: 0.050 C, 0.30 Mn, 0.007 P, 0.019 Si, 0.03 Cu, 0.02 Ni, 0.02 Cr, 0.045 Al, and 0.004 N. Two 4.5 by 13 by 0.078 in. sections were cut from the center section of a hot-rolled panel and one of these was reheated to provide two different conditions prior to cold rolling: low AlN: as commercially hot-rolled, with aluminum and nitrogen in solid solution; and high AlN: as commercially hot-rolled, then reheated at 1300°F for 3.5 hr to precipitate most of the nitrogen as AlN. ~etallc&a~hic examination indicated that the reheating did not change grain size nor carbide distribution (some spheroidization of pearlite was noted). Texture analysis at half-thickness level showed that both sections had the same substantially random as-hot-rolled texture. The results of check chemical analysis of each sample are given in Table I. Both sections were cold-reduced 65 pct on a laboratory rolling mill to a final thickness of 0.027 in. Cold rolling, in one direction only, was in the direction of the prior hot rolling. Specimens 1.0 by 1.25 in. were cut from the cold-rolled sheets and given a simulated box anneal in an atmosphere of 2 pct HZ-98 pct He. Specimens were heated at a constant rate of 40°F per hr from room temperature to various temperatures in the range 750" to 1300°F and cooled immediately by withdrawal to the water-cooled end of a tube furnace. The temperature in the 6-in. uniform hot zone of the furnace was controlled within 3"F. Selection of the individual specimens was made to give a random distribution of annealing temperatures with respect to location in the cold-rolled sheet. At least two specimens of each condition were annealed to the same temperature and smaller specimens for light microscopy, transmission electron microscopy, and X-ray studies were prepared from each of these. Rolling-plane sections for each of these studies were taken at half thickness. Light microscopy and transmission electron micro-

Jan 1, 1969

By A. T. Miesch, L. B. Riley

An error occurred in the preparation of Fig. 3, p. 249, of Basic Statistical Measures Used in Geo-chemical Investigations of Colorado Plateau Uranium Deposits. This figure shows the relation of the arithmetic mean: geometric mean ratio to the geometric deviation. Curves for the cases where n, the number of samples, is 100, 10, and 5 are too high with respect to the ordinate. The error is negligible at low geometric deviations, but becomes increasingly greater wi,th higher values of geometric deviation. Arithmetric mean values in Table I1 are not effected by the errors in Fig. 3. The authors will endeavor to supply copies of the revised curves on request; write to: A. T. Miesch, Geologist, Branch of Radioactive Materials, U.S. Geological Survey, Bldg. 25, Federal Center, Denver 25, Colo.

Jan 1, 1962

By Walter R. Crane

PAGE I. Apparatus and Methods.......... 406 1. The Magnetic Circuit...........406 2. Apparatus Employed in the Traction-Method...... 406 a. The Coils............409 b. The Pole-Pieces..........409 3. Methods of Testing Fields Produced by Different Pole.Pices.. ..409 c. Testing with a Search.Coil........410 d. Testing with Iron-Filings and Glass Tube.. .. .410 4. General Forma of Pole-Pieces.........411 e. Flat Poles............411 f. Conical Poles........... 411 g. Spherical Poles...........411 h. Chisel-Edged (Chamfered) Poles.......412 II. Magnetic Fields...........412 5. Methods of Testinq for Magnetic Permeability...... 421 i. The Rod-Method..........423 j. Method Employed in These Experiments......424 k. Difference in the Results of the Two Methods..... 425 l. The Traction-Method.........427 m. Effect of Loosening the Charge.......430 n Corrections...........432 6. Theory.............433 o. Effect of Varying Weight on Tractive Force..... 434 p. Effect of Varying Pole-Distance.......436 q. Effect of Varying Magnetization.......436 T. Effect of Varying Size.. .......437 a. Summary,........... 441 III. The Relative Magnetic Permeability of Various Minerals,. 443 The form and strength of magnetic fields have attracted much attention. especially in connection with the designing of dynamo-electric machinery—an art which has been revolution-

Jan 1, 1902

By Harry Gard Knox, F. R. Harris

This paper covers some of the problems presented to the oil industry in the drilling of oil wells in the open waters of the Gulf of Mexico. The hazards, delays and relative costs of offshore drilling are reviewed and various forms of drilling platforms discussed. The requirements of the offshore drilling rig are summarized together with the principal items affecting the cost of construction. Sea waves and their size and characteristics as affecting offshore platforms are reviewed. Drilling platforms are classified as fixed, or fixed and floating. Fixed platforms of the conventional cofferdam and pile-supported type are discussed together with their good points and their limitations. The desirability is pointed out of eliminating as much offshore work as possible where operations are subjected to constant and expensive delay and substituting therefor the prefabrication of structures ashore or in sheltered waters. Marked economy will come with the standardization of offshore rigs aid special means of transporting them to the site. Several types of structure which are partly pile-supported and partly buoyancy-supported are discussed and their possibilities of future usefulness commented upon. General Considerations The predominant attribute of offshore drilling equipment is that it must be equal to the job in hand. We therefore give first thought to the matter of adequacy. In view of the probable depth of drilling, the investment involved and the per diem labor costs, it is assumed heavy modern drilling equipment will be employed. In order to usc such equipment efficiently, the working deck must be ample in size and strength and supported so as to be relatively free from motion and from green seas even in heavy storms. These requirements necessitate a high and rigid land-based support for the drilling rig and machinery with plenty of space for supplies, such as pipe, mud, water and fuel, with reserves for days when transportation from shore is impracticable. In offshore rigs the crew will be housed onboard in comfortable quarters, probably air conditioned and equipped with a galley and refrigerated food storage. An important consideration will be the ability to transfer stores and crew to and from the rig in all but the heaviest weather and the platforms must be protected from the impact of supply vessels when alongside. It will be essential to maintain continuous communication with shore by radio or cable, not forgetting the possibility of a helicopter landing space for the transfer of crew and light stores as well as a means of general communication. Whatever structure is constructed must be secure from storms of hurricane force and a safe place for the operating crew to work. If the well comes in, the drilling rig will presumably be removed and a small but rugged pile-supported platform will remain to carry the Christmas tree with safe working space around it. It will be protected from damage on all sides by buffer piles or dolphins. It is assumed that the flowing oil will be piped to storage tanks in the vicinity of the well. An individual tank for each well or a

Jan 1, 1949

By C. O. Burgess, W. D. Forgeng

The results of an investigation of the ternary system iron-chromium-silicon were reported in 1936 by the present authors.l Partly for the sake of theoretical interest, and partly because of the possible commercial importance of these alloys, the present investigation was undertaken to determine the effect of some of the commoner elements likely to occur, deliberately or otherwise, in such alloys if made on a commercial scale. The elements thus added were carbon, nickel or manganese. The alloys studied were, therefore, parts of quaternary systems. This investigation was concerned primarily with the effect of these additional elements on the alpha-iron phase and the boundary between this phase region and the alpha plus sigma two-phase region. The sigma phase is a ternary solid solution based upon the compound FeCr. The work was performed mainly by X-ray methods, but a number of microscopic examinations were also made and are reported. While isolated alloys in the composition ranges studied may have been discussed in metallurgical publications, no systematic investigation of any assistance to us was found. Of the earlier work, the investigations on the iron-chromium-carbon system and on the chromium carbides by Westgren and his coworkers2&apos;3 enabled us to identify the carbide phase. Several articles appeared after the present experimental work had been completed. Lucas and Wintrup4 determined the solubility of carbon in molten iron-chromium-silicon alloys. Tofaute and his coworkers5&apos;6 have made detailed studies of the iron-chromium-carbon system, which will be referred to later. Materials and Methods Materials.—The iron, chromium and silicon used were essentially the same as those used in the investigation of the ternary system.l The

Jan 1, 1938