Search Documents

By I. R. Kramer, H. Shen, S. E. Podlaseck

The tensile and creep properties of aluminum in vacuum have been investigated. It was found that the general effect of a vacuum environment was to reduce the rate of work hardening. Results obtained from creep tests showed that lowering the test pressure from 2 x 10-4 to 10-7 torr produced a decrease in the activation energy as much as 500 cal per mole. An attempt is made to explain these effects in terms of how the surface-stress field of a specimen may be affected by a vacuum environment during plastic deformation. In a previous paper,' the results were reported of some of our early work on the effect of vacuum environment on the stress-strain curve of aluminum single crystals. This effort has been extended to the studies of the tensile and creep properties in vacuum as a function of various metallurgical parameters. Some of the recent surface-effect studies2'3 have revealed that a region of high dislocation density, the so-called "debris" layer, is formed near the surface of the specimen as a result of plastic deformation. This layer acts as a surface barrier to oppose dislocation movement. The strength of this barrier depends on the surface condition such as oxidation or surface removal. Experimental results obtained from surface-removal work2, 3 indicate that such a surface barrier, which may be characterized by a stress field, affects the applied stress and the rate of work hardening. In the case of aluminum, this stress field was found to be directly proportional to the strain and the strain rate; however, the slope of this curve is independent of orientation of the crystal and may be altered by using different surface treatment. Since the escape of dislocations may be retarded by the presence of an oxide on the surface of a specimen, it is expected that a change in the rate of oxidation in vacuum will affect the process of dislocation accumulation in the debris layer. Consequently, it also affects the plastic behavior of a metal. This paper reports the changes in some of the creep and tensile properties of aluminum in vacuum and discussions of the observed effects in terms of the concept of the "debris" layer. EXPERIMENTAL PROCEDURE Tensile Tests. A sketch of the tensile apparatus is given in Fig. 1. This apparatus was contained in a bell jar (14 in. diam by 24 in. high) connected to a 10-in. vacuum system. The load was applied to the specimen by means of a gear train which was driven by a magnetic clutch located outside the vacuum chamber. The specimen, held by a pair of square shoulder grips, was attached to the load cell at the top and the drive gear at the bottom. A displacement transducer was placed between the two grips as shown in the figure to measure the elongation. Signals of elongation and load were amplified and recorded on an X-Y recorder. The system was capable of detecting loads as small as 0.025 lb and displacements of 0.0002 in. Shoulder-grip specimens of aluminum single crystals, having a nominal square cross section of 1/8 by 1/8 in. and a 3-1/2-in, gage length, were grown by the Bridgeman techniques. The original purity was 99.997 pet. The orientations of the crystals investigated are shown in Fig. 4(a). The crystals were annealed at 600°C for 2-1/2 hr, electropolished, and placed in the vacuum test chamber without any delay. All the crystals were deformed at a strain rate of 4 x 10-5 sec-1 at 24o ± 3°C. A study was made to find whether a chemically passive surface film would give the same effect as a vacuum environment. Specimens of aluminum 1100 (0.187 in. diam with a grain size of 0.1 mm)

Jan 1, 1965

Mining Methods LUCIEN EATON, Chairman GERALD F. SHERMAN, Vice-chairman CHARLES W. WRIGHT, Secretary Alluvial Mining CLINTON BERNARD CHARLES H. MUNRO CHARLES JANE N H. R. NORSWORTHY Open-cut Mining Iron MAX H. BARBER J. A. MacKILLICAN Copper MICHAEL CURLEY H. B. TEMPEST Underground Mining Iron C. H. BAXTER CARL BREWER TENNEY C. DESOLLAR Copper W. B. DALY A. H. WOHLRAB R. W. THOMAS

Jan 1, 1934

By J. C. McKinnell

The appraisal of an oil lease may often be mad,? through production decline analysis, which requires description of the functional relationship between the oil production rate and either cumulative production or time. Heretofore, attempts to define the function appropriate to a given set of production data have depended to some extent on subjective procedures. The purpose here is to introduce an objective solution, obtained by combining the principle of least squares with the theory of equations. MATHEMATICAL ANALYSIS The fundamental differential equation appropriate to a general class of decline curves may be written. Solution of Eq. 1 for general boundary conditions may be written in terms of either the cumulative oil production or time: These equations constitute the mathematical expression of the so-called hyperbolic decline. Their complete description for a given set of production data requires the numerical evaluation of the three parameters1.', n, D, and (go),. For the special case of n = 0, Eq. 2 becomes q. = (q.), - DiN with the corresponding expression in terms of time being q. = (qa),e...........(5) Similarly, for the special case of n = 1, Eq. 3 becomes with the corresponding expression in terms of cumula- tive oil production being q. = (q.),e " '.......(7) Eqs. 4 and 5 constitute the mathematical description of the so-called exponential decline; Eqs. 6 and 7 are the mathematical description of the harmonic decline.',' Returning to the hyperbolic expressions, Eqs. 2 and 3 may also be written, q: = sNp + b........ (8) and where a = 1 - n; s = (n— 1)D,(q0);"; b = (go):-"; a'=-n;s/= nD,(qo);"; and b' = (go);-. Note that both Eqs. 8 and 9 are linear in either time or cumulative production with respect to an exponential function of the production rate. In other words, a straight line relationship results for both variables when associated with the appropriate power of q,. This fact is of prime importance in the application of statistical analysis. . STATISTICAL ANALYSIS For a given oil lease, the time, production rate and cumulative production are recorded records. To establish predictive formulas from Eqs. 2 and 3, it remains to determine numerical values for the three parameters [n, D, and (q,) .] through an investigation of the past history. Upon interpreting a, s and b as parameters, Eq. 8 may be expressed for every time interval of interest, i, over the past history as follows. (q,): = s(Np), + b........(10) In general, Eq. 10 will not be satisfied exactly, because of the assumptions in the expression of Eq. 1, and the errors and anomalies universally associated with production data. It will instead define the residual, s(Np), + b- CO=d......(11) Squaring both sides and summing over all the data points, m, under consideration yields

By Eric J. Jette, Frank Foote

The unusual physical, electrical and magnetic properties of the iron-nickel alloys has given rise to a voluminous literature. This work will be reviewed critically in "The Alloys of Iron and Nickel," a monograph of the Alloys of Iron Research Series, soon to be published. In what follows we shall therefore confine ourselves to those of the earlier investigations that involved the use of X-ray crystal-structure methods. The earliest X-ray work on the iron-nickel system was by Miss Andrewsl. Using the powder method of X-ray analysis purely as a means of identifying the phases present, she located a region between 20 and 30 weight per cent nickel in which body-centered and face-centered phases coexisted. No lattice constants nor details of heat-treatment were reported. Bain2 also reported some qualitative observations. McKeehan3 made a systematic investigation over the whole of the system, giving many of his alloys four and some five different heat-treatments. In alloys furnace-cooled from 900' to 950' C. he found two coexisting phases between 0.15 and 30 per cent nickel. The precision of the lattice-constant measurements was low in comparison with what can be obtained today. Even for alloys of the same heat-treatment, differences in the constants were often between two and ten parts per thousand. In regions where no change of lattice constant with heat-treatment should occur, differences of the same order of magnitude were found. Since the maximum change in the lattice constant of nickel with change of composition is only about 2 per cent of the constant for pure nickel, these variations in the constants for a given alloy cause the points to "scatter" badly about any curve that may be drawn to represent them and it is difficult to interpret such results. In spite of this, McKeehan shows that the lattice constant of nickel increased as the iron content increased. His results for the alpha-iron phase are less conclusive. Osawa4 also investigated the entire system. For alloys slowly cooled from 1150' C. and then filed into samples for X-ray analysis, he found

Jan 1, 1936

By Frank Foote, Eric J. Jette

The unusual physical, electrical and magnetic properties of the iron-nickel alloys has given rise to a voluminous literature. This work will be reviewed critically in "The Alloys of Iron and Nickel," a monograph of the Alloys of Iron Research Series, soon to be published. In what follows we shall therefore confine ourselves to those of the earlier investigations that involved the use of X-ray crystal-structure methods. The earliest X-ray work on the iron-nickel system was by Miss Andrewsl. Using the powder method of X-ray analysis purely as a means of identifying the phases present, she located a region between 20 and 30 weight per cent nickel in which body-centered and face-centered phases coexisted. No lattice constants nor details of heat-treatment were reported. Bain2 also reported some qualitative observations. McKeehan3 made a systematic investigation over the whole of the system, giving many of his alloys four and some five different heat-treatments. In alloys furnace-cooled from 900' to 950' C. he found two coexisting phases between 0.15 and 30 per cent nickel. The precision of the lattice-constant measurements was low in comparison with what can be obtained today. Even for alloys of the same heat-treatment, differences in the constants were often between two and ten parts per thousand. In regions where no change of lattice constant with heat-treatment should occur, differences of the same order of magnitude were found. Since the maximum change in the lattice constant of nickel with change of composition is only about 2 per cent of the constant for pure nickel, these variations in the constants for a given alloy cause the points to "scatter" badly about any curve that may be drawn to represent them and it is difficult to interpret such results. In spite of this, McKeehan shows that the lattice constant of nickel increased as the iron content increased. His results for the alpha-iron phase are less conclusive. Osawa4 also investigated the entire system. For alloys slowly cooled from 1150' C. and then filed into samples for X-ray analysis, he found

Jan 1, 1936

By V. A. Zanadvoroff

THE mine and concentrator of the Howe Sound Co., Chelan Division, are at Holden, in a remote section of the Cascade Mountains of northwestern Washington. Holden is at an elevation of 3200 ft., in the narrow valley of Railroad Creek. This creek drains into Lake Chelan, at a point some 40 miles up the lake from the town of Chelan. The concentrator treats 2000 to 2500 tons of low-grade copper-gold-zinc ore per day. Concentration is achieved by the differential flotation process, with recovery of 94 per cent copper and 82 per cent gold in the copper concentrate, followed by the recovery of 65 to 70 per cent zinc in the zinc flotation circuit. The final flotation tailing is deslimed, and coarse sands, representing 60 to 70 per cent of the total, are cyanided. The tonnage of tailing material amounts to 1900 to 2370 tons per day. GENERAL CONSIDERATIONS The property is within the Chelan National Forest. Railroad Creek is a fishing stream, being stocked regularly with trout from State hatcheries. Consequently, in planning a milling operation, the Howe Sound Co. was obliged to avoid any pollution of the stream by tailing material, and also destruction of valuable stands of timber. Moreover, the selected tailing disposal sites should not mar the natural beauty of the valley. In addition to these requirements, the problem of tailing disposal at Holden was complicated by topography and climatic conditions. The valley is long and narrow, averaging 1200 to 1500 ft. in width. Its walls are flaring at a steep angle. There are no extensive flat areas suitable for deposition of tailing. All valleys tributary to Railroad Creek, also the well-marked paths of snowslides, must be avoided. Finally, the direction of prevailing winds and possible dust hazard arising therefrom dictated the necessity of selecting the tailing-disposal sites downstream from the mill building and two campsites. Heavy snowfall during the winter months of November to March, inclusive, impedes building of the retaining dike, making it necessary to prepare the needed storage space during the summer months. It is inadvisable, also, to do any dike building during the freezing weather, because the dike becomes unstable with the spring thaws, producing inevitable "sloughing" of the built-up borders. TAILING-DISPOSAL SITES The existing tailing-disposal areas are near the south wall of the valley. They were developed, and put to use in the following sequence: No. I. Area.-Covers approximately 10 acres. Built up to the height of 60 ft.

Jan 1, 1946

The first meeting of the Naval Consulting Board was held at the office of the Secretary of the Navy, Washington, D. C., on Oct. 6, 1915. The Board organized by electing Thomas A. Edison, Chairman, Peter Cooper Hewitt, First Vice-Chairman, William L. Saunders, Second Vice-Chairman, and Thomas. Robins, Secretary. All of these officers are members of the American Institute of Mining Engineers. The other members of the Board are given below, and those who are members of the Institute are marked with an asterisk: *W. R. WHITNEY MATTHEW B. SELLERS. L. H. BAEKELAND. HUDSON MAXIM. FRANK JULIAN SPRAGUE. HOWARD T. COFFIN. BENJAMIN C. LAMME. ANDREW J. RIKER. R. S. WOODWARD. HENRY A. WISE WOOD ARTHUR GORDON WEBSTER. ELMER A. SPERRY. A. M. HUNT. *BENJAMIN B. THAYER. ALFRED CRAVEN. *J. W. RICHARDS. *SPENCER MILLER. *LAWRENCE ADDICKS. WILLIAM LE Roy EMMETT.

Jan 12, 1915

By O. Schaaber

THE existence of isothermal martensite without the presence of the athermal form thus far has been established only in a 6 pct Mn, 0.6 pct C steel' and a 23 pct Ni, 3.5 pct Mn-Fe alloy.' " Theoretical calculations, moreover, predict this phenomenon to be observable only within narrow composition limits.' In all other steels, it is generally considered that martensite inevitably forms upon cooling below the M, temperature. Even the possibility of isothermal martensite transformation has been questioned for the common steels, although Averbach and Cohen" showed that martensite formation does not stop when the cooling is arrested and that as much as 5 pct retained austenite may transform isothermally to martensite at room temperature. This note presents some observations made on a number of low alloy steels by dilatometric and inductive measurement of isothermal austenite transformation at various temperatures close to the Ms. In the dilatometer studies reported previously, austenitized specimens were immersed in a salt bath maintained at proper temperature and immediately inserted into the dilatometera8' already at thermal equilibrium with the bath. The dilation was read on a dial gage divided into 0.001 mm intervals. Induction measurements were made with a separate excitation source and a test coil, sealed together in a salt-tight case. The increase in the induced voltage caused by the transformation products was recorded at a paper speed of 4 mm per sec. The steels studied are listed in Table I. Specimens prepared from steels 1 and 2 were in the form of hollow cylinders 60 mm long, 10 mm ID, 14 to 16 mm OD, while specimens of steels 3 and 4 were in the form of notched-bar impact test specimens, DVM type. Specimens of steel 5 were in the form of strip, 7x0.3 mm. In the bainitic range, curves representing the amount of transformation vs log time have a single step appearance, as is shown by the curve of isothermal transformation at 320°C in Fig. 1.Y ransformation proceeds in accordance with the Austin-Rickett equationo P -----------= k t" 100-P where P is the percentage of transformed austenite, t is time, and k and n are constants. Near the M, temperature, however, complex curves having two steps are observed. As shown in a previous papera for steel 3 isothermally transformed at 245"C, such complex curves can be separated into two separate transformations or reactions each following the Austin-Rickett equation. The values of n in the equation for a number of such two-step transformations are listed in Table 11 for steel 1. At transformation temperatures of 250" and 235"C, evidence of a second transformation is very

Jan 1, 1956

By Stanley L. Lopata, Eric B. Kula

The problem of preferred orientation has been considered in quantitative phase analysis by X-ray diffraction techniques. The average intensity of a diffraction peak can be obtained by integration over the whole pole figure, or by random rotation of the specimen in the X-ray beam, or by a combination of both. For rod or wire, where the pole figure shows rotational symmetry, the intensity is measured along a radius of the pole figure. Where no symmetry is present, rotational symmetry is imparted by rapid rotation of the sheet around its surface normal during measurement. These methods are applied to the determination of aus-tenite in an Fe-31 pct Ni rod and Fe-28 pct Ni sheet. X-RAY diffraction techniques are frequently used for quantitatively determining the relative amounts of two or more phases present in a structure.1,2 Briefly, the method requires a measurement of the intensity of a Bragg reflection for each phase. The method is based on the principle that the intensity of a Bragg reflection, IA, is directly proportional to the volume fraction of the given phase present, CA: T KRACA/2µ [1] where K is a constant independent of the diffracting phase, RA can be calculated and depends on the Bragg angle ? and the particular reflection measured, and µ is the linear absorption coefficient of the mixture.' For a mixture of two phases A and B, IA = RAcA [2] IA/IB=RAcA/Rbcb and CA+ CB = 1 [3] This allows the volume fraction of a phase to be calculated directly from the measured integrated intensities of the two phases present. This method is frequently used for quantitatively determining retained austenite in steels, but can be used for the quantitative determination of in titanium alloys, as well as phases in other alloy systems. The intensities are generally measured by diffracting only from planes whose normals are perpendicular to the specimen surface, with the implicit assumption being made that this intensity is typical of reflections from planes whose normals lie at other angles to the surface. If the specimen contains a texture or preferred orientation of the crys- tallographic planes by virtue of previous mechanical working, however, this measured intensity is correct only if the intensity level fortuitously is one times random. Examination of pole figures for actual rolled sheet shows that the intensity level at the center of the figure is seldom at the random level, and can very easily differ by a factor of five or more, leading to a commensurate error in the calculated amount of the phases. Textures have been commonly found in materials which are cold-rolled or recrystallized after cold rolling. This problem is becoming of greater importance since structural materials in use today, such as the high-strength stainless steels, frequently are further strengthened by cold rolling, and hence contain textures. Although high-strength carbon-containing alloy steels generally do not contain textures, some of the newer thermomechani-cal treatments will impart a texture even in these cases. In the case of hexagonal metals, such as titanium, probably every wrought sample will show some anisotropy. Since the standard X-ray techniques are inapplicable in all these cases, there is a clear need for some method of taking this anisotropy into account. The specific problem is to obtain the integrated intensity of a Bragg reflection for each phase, averaged over all orientations of the sample with respect to the X-ray beam. This can be done either by purely mechanical means or by a mathematical averaging. Mechanically, a small spherical speci-

Jan 1, 1965

By J. Chipman, J. B. Gero, T. B. Winkler

D. C. Hilty—This paper is a useful and timely addition to our store of quantitative data relating to manganese distribution between slag and metal in steel-making processes. For some time, many of us have suspected that the values of Kmn derived by Körber and Oelsen might be too low, and this paper now appears to confirm that suspicion. Application of the new constant to openhearth data should prove interesting. The manganese deoxidation curves of fig. 4 agree fairly well with direct measurements of isothermal solubilities of oxygen in liquid iron containing manganese that have recently been made at the Union Carbide and Carbon Research Labs., Inc. According to the solubility data just mentioned, however, the curves for 1550" and 1600°C lie much closer to each other than the authors have indicated. In other words, the solubility measurements suggest that the logarithm of the oxygen solubility is not a linear function of the reciprocal of the absolute temperature, as the authors have assumed for their calculations. It seems possible that this discrepancy may be due in part to the authors' use of the distribution coefficient, L,,, obtained from Taylor and Chipman's curve for the solubility of oxygen in iron as shown in fig. 2. Taylor and Chipman gave the equation of this curve as —6320 Log % 0 - ---T + 2.734 Their data, however, can be fitted equally well by a curve having the equation: 13.23 x104 1.18x10" Log % O = 36.350 -13.23x10 Moreover, this curve also fits the authors' oxygen distribution data somewhat better than does the linear curve of Taylor and Chipman. Its use in the derivation of Lo for calculation of the deoxidation curves by the authors' eq 15 causes the effect of temperature on the calculated curves of fig. 4 to agree quite well with the temperature effect that has been observed. An experimental determination of the temperature coefficient of the manganese reaction appears to be desirable. J. E. Stukel—Because the authors have done such an excellent job, my comments will be confined to additional information. Very shortly Professor T. L. Joseph and I will publish the results of a study of the reaction between molten manganese and silica. It was found that electrolytic manganese, melted in silica crucibles, reacted with the silica to form a silico-manganese alloy containing 18 pct silicon (1500°C) and a silica saturated MnO-SiO, slag. Therefore, the presence of silicon and its oxides in the Fe-Mn-0 system will affect the equilibrium. Carbon is also an important factor. The higher the carbon content of the iron the less ability manganese has to reduce silica. As a matter of interest, recently a study of the manganese equilibrium in carbon saturated iron and blast furnace slags was completed at Carnegie Institute of Technology. As a comparison to the present study, 2 to 5 hr were required to reach equilibrium and temperature was a much more important factor than slag composition in determining the (Mn)/(MnO) ratio. These results will also be published in the near future. It can be seen, therefore, that the results of this paper cannot be applied directly to openhearth studies without a degree of flexibility. J. Chipman (authors' reply)—With regard to the effect of silicon on the manganese constant, this effect is, of course, known. Much more data is needed in order to establish it accurately, and I hope we can look forward to having some accurate data on that. Mr. Hilty suggests that a three-term expression for the Taylor-Chipman solubility of oxygen in liquid iron might fit a little better than the two-term equation. I think that it would be too great a compliment to the precision of the data to employ a three-term equation, and I would still recommend the simple, two-term expression.

Jan 1, 1951

[United Engineering Society WALTER H. ALDRIDGE J. VIPOND DAVIES J. V. N. DORR Engineering Societies Library Board SYDNEY H. BALL ALEXANDER C. HUMPHREYS GEORGE C. STONE JOHN H. JANEWAY Engineering Foundation Board H. M. BOYLSTOX J. VIPOND DAVIES GALEN H. CLEVENGER]

Jan 1, 1928

By Donald K. Weaver

THERE have been eight different oil zones identified and produced at Santa Fe Springs, of which three or four are in turn divided into two or three parts. These zones are, from top to bottom, the Foix, difference of opinion over this nomenclature, with reference to the different zones referred to as Clark, it has no particular bearing on the water problems. Each of these oil zones has had waters of varying salinity associated with it, either within or at the bottom of the 'zone. Table 1 is a tabulation of the zones, their maximum thicknesses, salinity and heads of various waters. Surface waters are fresh, and of high head, giving artesian flow in some instances.

Jan 1, 1930

By E. K. C. Williams, Nathaniel Arbiter

INTRODUCTION The surface processes involved in preparing ores for flotation and for operations depending on their flocculation/dispersion characteristics * vary widely in agitation dependence. Most of the reagents used for these purposes are added to grinding circuits, pump sumps, launders, or directly to flotation cells with the turbulent flow conditions usually adequate both for mixing reagents and for surface reactions without special conditioners. However, some reagent systems do require specific control of agitation intensities and reaction times, the more important of these being the following: 1. Activation of ZnS with CuSO4. With the usual conditions pH about 10, with collector added with the CuSO4, Cu 2+ is almost completely precipitated as basic compounds and as collector salt. As a result the levels of reagent in solution are extremely low which probably accounts for the need for separate conditioning. The agitation intensities are at about the 0.01 HP/ton level.** 2. Flocculation with natural or synthetic polymers. In this case the agitation problem is two-fold; first, to insure adequate initial mixing of the viscous stock solution of the

Jan 1, 1980

By AIME AIME

JOHN LIVERMORE CHRISTIE belongs to that group of metallurgists who entered the industrial field during World War I and have been responsible for many of the important metallurgical developments since that time. He was born in Montclair, N. J., on Jan. 31, 1894. After graduating from Montclair High School he attended Sheffield Scientific School, Yale University, received his Ph.B. degree in chemistry in 1915 and that same year was employed by the Bridgeport Brass Co. in its laboratory. Among his first duties was the return to Sheffield Scientific School for two years of graduate work in metallography under C. H. Mathewson; receiving his M.S. degree in 1917. Thus we see him becoming one of that group of eminent physical metallurgists who, with Dr. Mathewson's teaching as a foundation, have done outstanding work in metallurgy.

Jan 1, 1945

By Burt C. Mariacher

The Minerals Beneficiation Division meets each year at the Annual Meeting of AIME. All members are invited and encouraged to attend. For the information of those who did not attend the meeting in Denver last February, this column presents a summary of the reports given and topics discussed. Technical Committee Coordination Consolidation of technical programs having common interest to MBD and the Extractive Metallurgy Division is proving a considerable success, both on the technical committee level-through the efforts of the MBD-EMD Coordinating Committee-and in special symposia. MBD Chairman, R. S. Shoemaker, noted that J. D. Prater will be serving as Chairman of both the MBD Chemical Processing Committee and the EMD Hydrometallurgy Committee for 1970-71. R. P. Ehrlich commented on the cooperative effort of both divisions in organizing the Copper Metallurgy Symposium held at the Denver Meeting. This effort, he said, was important to the success of the Symposium. H. R. Spedden discussed inter-Division coordination activities on the SME level. The forthcoming MBD-M&E-EMD Joint Lead-Zinc Symposium is yet another example of progress in this direction.

Jan 1, 1970

Meeting, of Jan. 22, 1915.-Dr. Albert R. Ledoux was unanimously nominated-by the Board as one of the representatives of this Institute upon the Engineering Foundation Board. The following Tellers to count the votes for officers and directors on Feb. 16, 1915, were appointed: David H. Browne; Arthur S. Dwight, and Bradley Stoughton; and the following Tellers to count the ballots, on the amendments to the Constitution: Arthur L. Walker, Max Roesler, and Burr A. Robinson. Karl Eilers was appointed a member of the Library Board of the United, Engineering Society, representing this Institute in place of C. R. Corning, ;resigned. The Pick and Hammer Club of the University of Oklahoma was established as an Affiliated Student Society. The sum of $150 was appropriated to the Columbia Local Section. The sum of $29.50 was appropriated to the Chicago Local Section.

Jan 3, 1915

By Francisco Cadena

THE construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather closely, and this resulted in the accumulation of many data bearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general information as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars. Coarse Aggregate Aggregate for the concrete poured at Norris Dam came from a dolomite quarry within 2000 ft. of the west abutment of the dam. Geologically this rock is known as a Knox dolomite. A typical chemical analysis is given in Table 1. TABLE 1 .-Typica.1 Chemica1 Analysis [PER CENT H20,1100F ............................................ 0.0'2 Ignitionloss ............................................. 43.56 MgO .................................................. 19.19 CaO .................................................... 29.07 FezO .................................................... 0.39 A1203 .................................................... 1.94 FezO .................................................... 0.39 A1203 .................................................... 1.94 ..................................................... 5.75 SO2.. .................................................. Tr.] Rock was carried by 12-yd. dump trucks to a 42-in. gyratory crusher set at 6 1/2 in. The product of the primary crusher was taken by a belt conveyor to a double-deck vibrating screen followed by a 5 1/2-ft. cone

Jan 1, 1937

By Francisco Cadena

The construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather closely, and this resulted in the accumulation of many data hearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general information as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars. Coarse Aggregate Aggregate for the concrete poured at Norris Dam came from a dolomite quarry within 2000 ft. of the west abutment of the dam. Geologically this rock is known as a Knox dolomite. A typical chemical analysis is given in Table 1. Table 1.—Typical Chemical Analysis Per Cent H2O, 110° F............................................. 0.02 lgnition loss.............................................. 43.56 MgO.................................................... 19.19 CaO ................................................... 29.07 Fe²O³.................................................... 0.39 Al2O³ .................................................. 1.94 SiO2..................................................... 5.75 SO2...................................................... Tr. Rock was carried by 12-yd, dump trucks to a 42-in. gyratory crusher set at 6 1/2in. The product of the primary crusher was taken by a belt conveyor to a double.-deck vibrating screen followed by a 5 1/2-ft. cone

Jan 1, 1938

By Francisco Cadena

The construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather closely, and this resulted in the accumulation of many data hearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general information as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars. Coarse Aggregate Aggregate for the concrete poured at Norris Dam came from a dolomite quarry within 2000 ft. of the west abutment of the dam. Geologically this rock is known as a Knox dolomite. A typical chemical analysis is given in Table 1. Table 1.—Typical Chemical Analysis Per Cent H2O, 110° F............................................. 0.02 lgnition loss.............................................. 43.56 MgO.................................................... 19.19 CaO ................................................... 29.07 Fe²O³.................................................... 0.39 Al2O³ .................................................. 1.94 SiO2..................................................... 5.75 SO2...................................................... Tr. Rock was carried by 12-yd, dump trucks to a 42-in. gyratory crusher set at 6 1/2in. The product of the primary crusher was taken by a belt conveyor to a double.-deck vibrating screen followed by a 5 1/2-ft. cone

Jan 1, 1938

By M. W. BERNEWITZ

ALTHOUGH many persons know that a lot of type metal and etchings are used in the U. S. Government Printing Office few would expect to find anything on metals in the annual report of the Public Printer, George H. Carter. Yet the report for the fiscal year ended June 30, 1931, contains many interesting items. For example: Among the 57,500,000 lb. of materials and supplies delivered to the printing office was little new metal, but the metal in circulation is 6,000,000 to 7,000,000 lb. In the cost of production $31,523 is charged against metal, nearly one-third for salaries and wages. In miscellaneous sales were $4,696 from waste metal and $1,147 from waste gold (from books). Electrotype and stereotype covered 11,438,314 sq. in. The vaults and storage rooms contain 1,700,000 plates and 130,000 pages of type containing 4,600,000 lb. of metal valued at $275,000. In what was known as the Congressional Globe vault were 46,000 stereotype plates; these were salvaged by remelting for other platemaking service. The Congressional Record superseded the Congressional Globe in 1873.)

Jan 1, 1932