Search Documents

[A AALSETH, EARL P GEOLOGIST. AMERADA PETROLEUM CORP. BOX 1498 BILLINGS. MONT ABADIE, HENRY G ASST TO SUP OF OPER LONG BEACH OIL DEVEL. CO. 255 S. SANTA CLARA. LONG BEACH, CALIF. ABBE. TRUMAN W. … ASST.FLD.SUP.OF PROD SUN OIL COMPANY BOX 66 STOWELL. TEXAS ABBOTT. J. L. .... GEOL. PARTNER PRITCHARD & ABBOTT 504 CENTURY BLDG. FORT WORTH, TEX ABBOTT, RICHARD H OWNER ABBOTT AND HOWARD OIL 422 W. HERMOSA DR. SAN ANTONIO, TEXAS. ABBOTT, SETH J.. JR PETR ENGR.]

Jan 1, 1961

By Ronald E. Versaw

Environmental legislation, both existing and proposed, requires that mills, tailings dams, evaporation ponds, and related processing facilities be located, constructed, and operated within stringent guidelines. An early step in planning a new processing facility is performing a site selection study in which topographic, hydrologic, geotechnical, and environmental parameters are evaluated for several alternate sites. Once a site is selected, then an environmental report, including a description of the proposed action, alternatives, baseline surveys, and discussions of potential environmental impacts, mitigation measures and monitoring programs is required. The federal legislation, siting studies, and environmental studies (along with the implications of these as they affect design) are discussed. In addition, costs for performing these studies and implementing control of effluents are discussed.

Jan 1, 1978

THE first session of the production engineering group on Wednesday, morning, with J. B. Umpleby as chairman, recorded the principal developments since the Fort Worth meeting. Added to this was a lively discussion of pressure maintenance. Recent advances in the air-gas lift have resulted from the need of applying the method to smaller wells at lower costs. In many places intermittent flow has given excellent results, and numerous mechanical de-vices for its automatic control have been, developed. Papers by C. V. Millikan on the Mid-Continent field and by A. H. Bell on California, fields formed the basis for discussion. The maintenance of initial sand pressures was ably discussed for two Texas fields by t. V. Foran in a paper that not only outlined the technic of operation and the results obtained but also contained noteworthy cost data in terms of increased ultimate production. Mr. Foran recommends the use of air in the first stages of pressure maintenance as a means of determining sand conditions and directions of flow, later turning to gas, if available, because of its greater solubility on oil. A round table discussion on petroleum engineering educational problems, with H. G. George as chairman, brought out much interesting discussion that is difficult to summarize. The other Wednesday morning session was a refinery engineering symposium with T. G. Del-bridge as chairman and the economical application of heat for the general topic. A paper on the modern pipe -still, by H. S. Bell, and another by C. W. Stratford on the modernization of the cylindrical still elicited a lively discussion.

Jan 3, 1928

By Gordon E. Agar

Several correlations have been proposed to relate energy consumption and size reduction in comminution, and although these are arrived at from different starting points, it is postulated that they are all statements of the same basic concept. To test this postulate, the dry ball mill grindability of langbeinite was determined, and the results were analyzed according to the various methods. An examination ' of the energy-particle size relationships proposed in the recent past revealed that they had much in common. In fact, the conclusion was tentatively drawn that these expressions were essentially the same, even though they were arrived at from quite different basic premises. The equations attributed to Charles2 and Holmes3 were shown to re- duce to the same single equation, W - A K-3, and the simulated continuous test used by Maxson et al.4 was shown to give the best experimental value of the required empirical parameter, ß. Furthermore, the size distribution parameter a in the Schuhmann equation, y - (x/K)2, was shown to be equal to ß in many cases. The kinetic approach used by Arbiter and Bhrany5 should give the same results as the Maxson test procedure; however, the batch operation used by Arbiter and Bhrany could not produce data that would be as precise as the simulated continuous technique. To test the validity of these conclusions, the simulated continuous method was used to obtain data on the dry grinding of langbeinite. The results are discussed in terms of the various equations and approaches. APPARATUS AND MATERIAL A ball mill with internal dimensions of 17.5 cm (6 7/8 in.) in length by 19.4 cm (7 5/8 in.) in diam was loaded to 50% of its volume with balls 3.2 cm in

Jan 1, 1969

EXECUTIVE COMMITTEES OF LOCAL SECTIONS Arizona E. P. MATHEWSON, Chairman W. V. DECAMP, First Vice-chairman F. W. MACLENNAN, Second Vice-chairman E. D. GARDNER, Secretary-Treasurer, U. S. Bureau Of Mines, Tucson, Ariz. MICHAEL CURLEY J. P. HODGSON HENRY F.1 ASTER CLYDE E. WEED Boston Meets first Monday each winter month GEORGE A. PACKARD, Chairman FRANKLIN B. RICHARDS, Vice-chairman F. LEROY FOSTER, Secretary-Treasurer Rooms 8-219 Mass. Inst. of Tech., Cambridge, Mass. G. W. METCALFE D. H. MCLAUGHLIN

Jan 1, 1932

By A. H. Daane, B. J. Beaudry

The yttl-irtm-nickel system has been investigated by metallo-graphic, thermal ard X-ray methods. There are nine intermetal-lic compounds present: Y3Ni, Y3Ni,, YNi,, YNi,, Y,Ni,, YNi,, and Y,Nil, which rodergo peritectic decomposition and YNi and YNi, which melt congruently. There are eutectics at 34.8, 57.5 and 93.3 at pct Ni which melt at 805°, 950 and 1285 C, respectively. Crystallographic data are given for YNi, YNi,, YNi,, YNi5and Y,Ni,. The terminal solid solubility is low. In recent work by Fisher and Fullhart' in which yttrium crucibles to be used for containers of uranium-chromium eutectic were clad with a high nickel steel, a low melting phase formed where the yttrium was in contact with the steel. To investigate the cause of this phenomenon, Daane, et al. made a survey study of yttrium systems with chromium, manganese, iron, and nickel and found an 18 wt pct Ni (weight percent) alloy to melt at approximately 950°C. voge13 in a study of the systems of cerium, lanthanum, and praseodymium with nickel found six compounds of the same formula in each system, i.e., R3Ni, RNi, RNiz, RNi3, RNi4, and RNi5. Since there is a great similarity between yttrium and the rare earths, compound formation was likely to occur also in the yttrium-nickel system. voge13 observed that the ability of transition metals to form compounds with the rare earths diminishes in the order nickel, cobalt, and iron while no compounds are formed with manganese, chromium, and titanium. Available data on yttrium systems with these elements indicate similar behavior, except that a slightly greater tendency toward compound formation is apparent. Simple eutectics with limited solid solubility have been found in the yttrium-titanium4 and yttrium-chromium5 systems, but at least one compound is present in the yttrium-manganese system.' In the case of yttrium-iron, at least three compounds are present,5 while only two are present in the cerium-iron,' and no compounds are present in the lanthanum-iron5 system. On the basis of both the trend in the alloying behavior of yttrium and rare-earth metals with the first transition series metals and the large number of compounds in the cerium-nickel system, one might expect six or more compounds to form in the nickel-yttrium system. A consideration of Hume-Rothery's rules of alloying based on size factor, electronegati-vity, and valence predicted low terminal solid solubility and possible compound formation. The present study was undertaken to confirm these predictions of

Jan 1, 1961

By Bernard Kopelman

The particle size of tungsten metal powder used to make tungsten wire for use in radio tubes and incandescent lamps must be closely controlled if the highly desirable feature of nonsagging is to be achieved. Our knowledge of factors affecting the particle size of tungsten powder has been limited by lack of any extensive literature on the subject. There are no publications in the English language discussing this problem in any but the most general terms. In this paper the published experimental information on this subject is reviewed. Based on the published data and some experimental data obtained by the author, a general theory of factors affecting the particle size of tungsten metal powder obtained by reduction of the oxides in hydrogen is offered. The various forms of the tungsten oxides and tungsten metal used in the experiments described were those prepared by commercial processes, so that the experimental results obtained on a laboratory scale would be more directly applicable to actual commercial reduction conditions. The effects of time of reduction, temperature. and concentration of water vapor in the hydrogen were observed by counting microscopically the particle distribution obtained. Such a method is very time-consuming, but the data obtained by this method are more reliable and more fundamental than those obtained by any of the several instruments available for measurement of particle size. Review of the Literature Until the year 1912, tungsten powder was prepared commercially by reducing tungstic oxide in the presence of carbon or one of its compounds (such as glycerin or ethylene glycol), usually by firing the mixture in a closed fire-clay crucible. The resultant powder contained about 95 per cent tungsten.' When reduction of tungsten oxides by H² was introduced Commercially,²,³ several investigators became concerned with the equilibria between tungsten metal and its several oxides in an atmosphere of hydrogen and water vapor.4-l3 While these many investigations were in fair agreement on the equilibria WO³ + H2 = WO2 + H2O and WO2 + 2H2 = W + 2H2O there arose considerable controversy as to the chemical composition of the oxide between WO³ and WO², because of very poor agreement on the equilibrium constant of this intermediate oxide reduction reaction. The controversy on this intermediate oxide has been in progress for more than 100 years. Thus Malguti,14 in 1835, decided it was WO2.56 In 1857, Riche15 proposed the formula W³O8. Usler,16 in 1865, confirmed the existence of WsO8 and further proposed W1O1l. In 1897, Desil7 agreed upon W²O8 but also found W5O14.

Jan 1, 1947

By Bernard Kopelman

The particle size of tungsten metal powder used to make tungsten wire for use in radio tubes and incandescent lamps must be closely controlled if the highly desirable feature of nonsagging is to be achieved. Our knowledge of factors affecting the particle size of tungsten powder has been limited by lack of any extensive literature on the subject. There are no publications in the English language discussing this problem in any but the most general terms. In this paper the published experimental information on this subject is reviewed. Based on the published data and some experimental data obtained by the author, a general theory of factors affecting the particle size of tungsten metal powder obtained by reduction of the oxides in hydrogen is offered. The various forms of the tungsten oxides and tungsten metal used in the experiments described were those prepared by commercial processes, so that the experimental results obtained on a laboratory scale would be more directly applicable to actual commercial reduction conditions. The effects of time of reduction, temperature. and concentration of water vapor in the hydrogen were observed by counting microscopically the particle distribution obtained. Such a method is very time-consuming, but the data obtained by this method are more reliable and more fundamental than those obtained by any of the several instruments available for measurement of particle size. Review of the Literature Until the year 1912, tungsten powder was prepared commercially by reducing tungstic oxide in the presence of carbon or one of its compounds (such as glycerin or ethylene glycol), usually by firing the mixture in a closed fire-clay crucible. The resultant powder contained about 95 per cent tungsten.' When reduction of tungsten oxides by H² was introduced Commercially,²,³ several investigators became concerned with the equilibria between tungsten metal and its several oxides in an atmosphere of hydrogen and water vapor.4-l3 While these many investigations were in fair agreement on the equilibria WO³ + H2 = WO2 + H2O and WO2 + 2H2 = W + 2H2O there arose considerable controversy as to the chemical composition of the oxide between WO³ and WO², because of very poor agreement on the equilibrium constant of this intermediate oxide reduction reaction. The controversy on this intermediate oxide has been in progress for more than 100 years. Thus Malguti,14 in 1835, decided it was WO2.56 In 1857, Riche15 proposed the formula W³O8. Usler,16 in 1865, confirmed the existence of WsO8 and further proposed W1O1l. In 1897, Desil7 agreed upon W²O8 but also found W5O14.

Jan 1, 1947

By Margaret G. Scroger, Luke L. Y. Chang, Bert Phillips

Using the sealed-system technique, isothermal sections at 1000°, 1400°, and 1700°C for the system Co-W-O hare been determined. The equilibrium data were obtained by microscopic and X-ray diffraction examination of samples winch had been equilibrated in pellet form fit sealed capsules and subsequcelly quenched. The only ternary phase in the system is CoWO, which mells congruentlly at approximately 1280°C. At 1000°C, this ternary phase exists in equilihrinm with all the allows and oxide compounds in the hounding binary systems. At 1400°C, liquid forms in thin oxygen-rick region near the CoWO4 composition and only one phase assemblage in the system (W + WO2 + H'5CV7) contains no In order for tungsten to be used to its full potential as a refractory metal. it is necessary that coatings be developed which will preclude oxidation of the metal. It is true that coatings now in use do protect tungsten for short periods at temperatures near 1700 °C. but no coating has been developed which protects adequately at or above this temperature where the use of tungsten is most required. This situation exists despite the great effort in recent years to develop such coatings. and it has become evident that success in this area can be achieved only after a more fundamental knowledge of the thermochemical and therrnophysical propertics of tungsten oxidation and tungsten -metal oxidation is obtained. In our 1aboratories. a project liclrriel. At 1700°C, tungsten is the ouly solid phase which is stctble, and a large range of compositions melt to two liquids, one metallic and one oxidie. The sealed-system method of etjuilibra lion prevents the determination of the partial pressure of oxygen and the total gas pressure orer the condensed phases at equilibrium. This data is not available and can be obtained only by some other method. We can generalize on these unknowns and indicate that both partial pressure of oxygen and total pressure of the gas phase must increase as compositions change from the W-Co binary toward the oxygen apex and as temperatures increase. has been initiated which is directed at providing some of this fundamental information through a study of metal-tungsten-oxygen reactions and equilibria and the properties of any intermediate phases which result. This paper is based on a part of this program in which the system Co-W-O was studied between 1000° and 1700°C. I) RELEVANT INFORMATION FROM THE LITERATURE A) The Notable Lack of High-Temperature Work on Metal-Tungsten-Oxygen Systems. It should be pointed out that there has been no published report (of which we are aware) which deals with the study of a metal-metal-oxygen system at 1700°C. Also, there has been no report on a complete metal-luugsten-oxgen system at any temperature. As a matter of fact. before this program started. The

Jan 1, 1965

By Otto C. Kopp, Thomas B. Crattie, Dennis R. Owen

Whole-rock analyses of limestones, fine-gralned dolostones and coarser-grained dolostones adjacent to mineralized breccias (Coy mine, Mascot-Jefferson City district) were compared with similar lithologies adjacent to apparently non-mineralized breccias at the new Thorn Hill section located approximately 39 km north of the Coy mine. Specimens were analyzed for Ca, Mg, Si, Al, K, Fe, Mn, Sr, Br, C1, S, Ti and P using X-ray fluorescence analysis. The concentrations of the major and most minor elements for Thorn Hill specimens fall within the range of concentrations for Coy mine specimens; however, significant differences (probability < 0.05) were noted for Fe, C1 and Br for fine-grained dolostones and for MgO, Fe and Mn for the coarser-grained dolostones. No significant differences were detected for the limestones.

Jan 1, 1985

By R. W. Heins, N. Street

Recently Hiller1 reported results on the impairment of the strength of quartz glass rods through wetting, indicating that there was general agreement with the prediction of the Griffith formula in that for the liquids used the rods were weakest in water i.e. the liquid which probably had the greatest free energy of immersion. The Griffith equation predicts that the tensile stress necessary to propagate a crack of length c is where ? is the interfacial free energy, E Young&apos;s modulus. Since for a solid immersed in a liquid of surface tension ?L and contact angle 8 at the solid-liquid-gas contact, ?s - ?SL = ?L cos ? where ?s is the surface free energy of the solid. Hence comparison between ?L cos 0 and strength impairment should be possible. In a study of the usefulness of the Kuznetsov pendulum2 as a means of studying rock drillability we have determined the effects of various liquids on the pendulum hardness of Bavarian limestone. The pendulum used had diamond points (Burgess Vibro-graver), a period of 1.14 sec and a total on sample weight of 1191 g. The decline of the pendulum oscillations was recorded by a light beam on light sensitive paper carried on a kymograph. Rehbinder&apos;s expression relating hardness to amplitude attenuation as a function of time can be written In A = - (1/H) t + In Ao where A, A, = amplitude at time t and initial amplitude respectively, H = hardness parameter, and t = time. The line of best fit to the experimental points was determined using the IBM 7090 electronic computer, the computer also gave A, by extrapolation to zero time. The results for the various liquids tested are given in Table I and Fig. 1. The limestone surfaces were highly polished before testing and each reported hardness value represents the average of at least ten separate determinations of the pendulum decline curve. On each newly prepared surface the water value was again determined (also

Jan 1, 1964

By Blake M. Loring

RECENTLY the S-curves for 30 to 40 alloy steels have been published.1,2 These steels show individual characteristics, which make each additional S-curve of great interest. There are important differences in the mechanism of the transformation process, the type of transformation product, and the influence of alloying elements. Steels of the same general alloy composition may possess such variable characteristics with regard to the length of time of isothermal transformation that an S-curve for each heat of steel may be desirable. In the present work the isothermal transformation of a steel having the following composition and grain size was studied: 0.20 percent carbon; 0.21 manganese; 0.026 phosphorus; 0.017 sulphur; 0.056 silicon; 1.45 chromium; 3.25 nickel; austenite grain size, 7. The progress of the isothermal transformation was followed by several different methods, including hardness measurements, dilatometer observations, and examinations of the microstructure. It was not expected that these methods would be in precise agreement.3 Accordingly, the changes in microstructure and hardness were given additional weight in determining the initial stage of transformation and the dilatometer measurements were relied on in estimating the completion of the process. The beginning of transformation was indicated by I per cent of transformation products and the end of transformation by about 99 per cent. The reproducibility of the various methods in the ranges of highest sensitivity was checked by several observations at each time and temperature. The steel used in this investigation was annealed for 24 hr. at 925°C. Macroetching revealed no serious segregation. The specimens for the metallographic and hardness investigations were 1 1/4 by 1/2 by 1/8 in. Wires attached to the samples were used for handling, instead of tongs, to avoid chilling. The specimens were heated at 845°C. for 1/2 hr. and quenched into constant-temperature salt baths held at various temperatures from 205° to 650°C. The time required to transfer the specimens was found to be about x 1 1/2 sec., and nearly 5 sec. more was required for them to come to the temperature of the bath. After various lengths of time in the constant-temperature baths the specimens were quenched in water at 21°C. The specimens were cut in half for the metallographic examination, to provide a surface free from decarburization. To determine the beginning and end of the transformation the percentage of transformation determined metallographically and by hardness was plotted against time. A planimeter was used in the metallographic determination. The hardness and metallographic determinations made at room temperature were confirmed reasonably well by dilatometer measurements taken during the process of transformation at the various temperatures. Two dilatometers were used to

Jan 1, 1941

By J. M. McDowell, E. C. Doty, F. Morgan

Improvements in the X-ray method of measuring liquid saturation and saturation distribution are presented. Two identical direct current amplifiers have been added to measure continuously the intensities of the X-ray tube output and the beam which has passed through the core under test. The ratio of these intensities is automatically recorded on a modified Brown Electronik Recorder. Arrangements have been made to drive the core automatically and in synchronism with the recorder chart so as to give a continuous curve showing the variation of liquid saturation along the length of the core. By determining the ratio of the two X-ray beam intensities simultaneously the measurements are made essentially independent of small fluctuation in voltage and current supplied to the tube. This improved technique has been used for investigating the fluid distribution along the length of cores and core assemblies when one fluid is displaced by another. Typical results of these studies are shown. INTRODUCTION In a previous publication&apos; a method was described for measuring the oil saturation in cores which was based on the absorption of X-rays by the fluid content of the core. While that technique is capable of yielding accurate results, the original apparatus was not especially convenient for determining the fluid distribution along the length of a core. This was primarily due to the slow response of the amplifier and galvanometer and the necessity of making a point by point survey of the material under investigation. It was, therefore, not only possible for sections of the core having a variable or unusual saturation distribution to escape observation entirely, but changes in output of the X-ray generator between readings on the unknown and the monitor introduced errors in the measurements that could be avoided only by further stabilization of the source or by taking a large number of readings. This paper describes a method and apparatus for recording continuously and automatically the intensity of the X-ray beam that is transmitted by a core. The variation of saturation with time at a given section of the core may thus be found, or by scanning the core by driving it in synchronism with the recorder the saturation distribution may readily be determined. As indicated in the previous paper, the X-ray method possesses an advantage over the weighing technique in relative permeability experimentation in that the core need not be removed from the holder for the purpose of making a saturation measurement. Furthermore, the actual distribution of fluid and the effects upon that distribution of inflow and outflow heads may be investigated. And errors due to gas bubbles or loss of liquid that are frequently sources of error in volumetric methods of saturation determination are avoided. PRINCIPLE OF THE METHOD The energy in an X-ray beam that has passed through an absorbing material is expressed by the well known formula: E = E0, e-cd (1) where E, is the energy in the incident beam, µ the mass absorption coefficient, c the density or concentration of absorbing material, and d is the length of path of the beam in the absorber. The coefficient µ varies with the wavelength of the radiation as well as with the absorbing material. The output of an X-ray tube varies in an approximately linear manner with the tube current, but to the second or higher power of the anode voltage. Moreover, the quality or wavelength distribution of the radiation varies with the voltage.

Jan 1, 1950

By AIME AIME

THE Industrial Conference appointed by President Wilson has presented the following tentative plan for preventing or retarding strikes and industrial conflicts by proposing new Federal machinery for the adjustment of differences between employers and employees. Theplan is signed by William B. Wilson, Secretary of the Department of Labor, &apos;as chairman of the conference; Herbert Hoover, former Federal Food Administrator, as vice-chairman; Martin H. Glynn; Thomas W. Gregory, former Attorney Gen¬eral; Richard Hooker; Stanley King; Samuel W. McCall former Governor of Massachusetts; Henry M. Robin¬son; Julius Rosenwald; Oscar S. Straus; Henry C. Stuart, former Governor of Virginia; F. W. Taussig; William O. Thompson; Henry J. Waters; George. W. Wickersham, former Attorney General; and Owen D. Young.

Jan 1, 1920

By Victor Lenher

The interest shown recently in selenium and tellurium has brought many requests for an assembling of the analytical chemistry of these two elements. The intention of this paper is to discuss all of the chemical principles utilized in the detection and quantitative determination of these elements, as well as to describe the works methods actually followed by producers of tellurium and selenium in the United States. These methods have been furnished by S. Skowronski of the Raritan Copper Works, H. D. Greenwood of the United States Metals Refining Co., F. F. Colcord of the U. S. S. Lead Refinery, and E. W. Rouse and A. E. Hall of the American Smelting and Refining Company. Occurrence Selenium is found associated with sulfur, to which in many respects it is quite similar. Occasionally deposits of native sulfur, notably those in the Lipari Islands, Kilauea, and Japan, show a red-brown coloration, I which is readily distinguished from that of other sulfur; this red-brown * sulfur contains a small amount of selenium. Not infrequently, the , sulfides of the heavy metals are accompanied by selenium and tellurium, • presumably as selenides and tellurides. The Scandinavian pyrite, which is one of the large sources of European sulfuric acid, when roasted has fur- - nished a large part of the selenium that has come to the United States; it I was in flue dust from the roasting of Scandinavian pyrites that the element was discovered by Berzelius in 1817. Greek and Spanish pyrites also

Jan 1, 1923

By Victor Lenher

The interest shown recently in selenium and tellurium has brought many requests for an assembling of the analytical chemistry of these two elements. The intention of this paper is to discuss all of the chemical principles utilized in the detection and quantitative determination of these elements, as well as to describe the works methods actually followed by producers of tellurium and selenium in the United States. These methods have been furnished by S. Skowronski of the Raritan Copper Works, H. D. Greenwood of the United States Metals Refining Co., F. F. Colcord of the U. S. S. Lead Refinery, and E. W. Rouse and A. E. Hall of the American Smelting and Refining Company. Occurrence Selenium is found associated with sulfur, to which in many respects it is quite similar. Occasionally deposits of native sulfur, notably those in the Lipari Islands, Kilauea, and Japan, show a red-brown coloration, I which is readily distinguished from that of other sulfur; this red-brown * sulfur contains a small amount of selenium. Not infrequently, the , sulfides of the heavy metals are accompanied by selenium and tellurium, • presumably as selenides and tellurides. The Scandinavian pyrite, which is one of the large sources of European sulfuric acid, when roasted has fur- - nished a large part of the selenium that has come to the United States; it I was in flue dust from the roasting of Scandinavian pyrites that the element was discovered by Berzelius in 1817. Greek and Spanish pyrites also

Jan 1, 1923

By Bailey, Lewis Newton

Bailey, Lewis Newton, Master Engineer, Senior Grade, 4th Regiment, U. S. Engineers, Headquarters Company, died of pneumonia at Camp Merritt, N. J., on Apr. 30, 1918. Baird, Louis, Lieut., Royal Field Artillery, British Army, died on the battlefield in 1915. Ballamy, John H., Capt., 103d Engineers, killed in action near Fismes, Aug. 9, 1918. Bowles, Martin F., 2d Lieut., Co. B, 355th Infantry, killed in action, Sept. 3, 1918. Burt, Andrew, died in active service, 1916. Cobeldick, William Morley, Royal Engineers, died from gas poisoning on Oct. 7, 1915. Dougall, Ralph, 4th University Co., Princess Patricia Regiment, killed in action early in the war. Evans, Alfred Winter, Lieut.-Col., New Zealand Rifle Brigade, D. S. 0., D. C. M., killed in action on Oct. 12, 1917.

Jan 3, 1919

By R. C. Ferguson, Harlowe Hardinge

Oscar Johnson—In my opinion, the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. Comparing the entire groups of operators with those who have had the opportunity to make slow-speed mill studies, I think you will find the latter small in numbers. Most managers want the equipment worked to its maximum output. There are, however, some installations where plant and mill sizes are such that they can do the job with reduction of mill barrel speeds. The past and the present installations of the industry are laid out to get the most capacity for the least capital outlay. This is the case even with the plants of Chile Exploration, International Nickel, Morocco, and Anaconda, now under construction or being changed. The industry recognizes that most all equipment it buys today is good and can be depended upon for efficient performance. Under this scheme of things, I am doubtful that slow-speed ball mill operation will be generally applicable. With reference to the U. S. Bureau of Mines laboratory tests, I think table II could have been omitted. It is inconclusive as to maximum efficiency for the low-pulp level mill on hard ore. There should be no question about this point. However, data on mill speeds can be found to substantiate various theories as well as refute them. Gow, Guggenheim, Campbell and Coghill, in their paper on Ball Milling,&apos; believe their 2 x 2 ft laboratory mill reflects results that can be expected from large mills. If so, then referring to their table 11, they state, "The conclusion to be drawn from this second series is that high speed, not exceeding 72 pct of the critical, favors capacity, as before, but that with proper conditions of operation high speeds may give as good efficiency values as low speeds. In this case the efficiency values are nearly constant. A horizontal curve would indicate that the amount of grinding was directly proportional to the power expended, and these tests suggest that such a coildition can be made to exist in commercial operations." Table II (From Paper by Gow et a1)2 Speed. Pot Critical 32 42 52 62 72 82 Capacity: Surface tons per hr (65- mesh) 266 42.1 54.4 65.9 74.3 74.1 Surface tons per hr (200- mesh) 56.1 87.4 112.7 137.1 154.2 153.0 Efficiency: Surface tons per net hp hr (65-mesh) 35.7 36.3 36.3 35.4 34.3 32.3 Surface tons per net hp hr (200-mesh) 75.3 75.3 75.1 73.7 71.0 66.0 Ore in mill, 1.b. 98 100 100 113 122 165 The field performance data, table 111, represents much effort in its collection and preparation. But, one must realize that there are many variables that effect the efficiency of grinding mill operation, and too much must not be assumed as to the effect of some specific change. Possibly with changes in mill speed, the results might be more consistent by also a change in ball rationing, type of ball, volume of ball charge,. p.ulp level and amount of pulp in the mill, pulp consisting, design of liner, circulating load, etc. Also, changes in ore character must be reckoned with when evaluating grinding performance. At present the Climax Molybdenum Corp. is running at much reduced capacity. Mr. James Duggan informs me that at mill speeds of 17 rpm, they save a $0.025 per ton on liners and $0.025 per ton in power, but, if the demand for molybdenum increased, he would go back to higher speed to obtain maximum tonnage, as the values from the increased tonnage would far more than offset the one half saving at the slower speed. The Jnspiration ran a six months&apos; test between mills running 21 rpm and 23.5 rpm. The slower mills ground 10 pct less ore with a slight saving per ton, but when the reduced plant tonnage was checked back into the actual cost figures of concentration, the high-speed mills with their greater tonnage showed considerable advantage. To be convinced of possible practical results from the predictions in the conclusions, I think we would have to rely on the analysis of expert cost accountants to furnish the necessary proof figures. Hardinge and Ferguson are to be commended for the work in preparing this paper. I am convinced that our Massco engineers should go into higher speeds with our equipment. Harlowe Hardinge (authors&apos; reply)—For one, I heartily agree with Mr. Johnson&apos;s opening statement that the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. It was on this basis and for this reason the paper was written. Mr. Johnson, on the other hand, takes the position that, on the whole, low speeds are not justified from the economic standpoint, basing his principal reason on the fact that lower mill speeds cut mill capacities and hence reduce the gross income from the product produced. There is no denying this point. It is almost axiomatic. It is for this very reason that the overall advantage of lower mill speeds has been discounted and even overlooked. It was for this reason mainly that the paper was written in the first place. It is one thing to plan an efficient operation at the outset, basing one&apos;s figures on the tonnage requirements at the time, and it is quite another to be confronted with the problem of increasing the output of an existing installation at a minimum of capital expenditure. Economic consideration of a new installation is greatly influenced by referring to an old one. Too often, the analyst assumes that if this practice is followed in the new installation, one would not go wrong. It is just here that he may be wrong. Past practice and low capital expenditure are all too frequently given priority over the engineer&apos;s analysis of operating costs. When we are able to start fresh, we should give proper weight to other economic factors which do not exist in an old installation. It is these economic factors that make it possible to spend at the outset just a little more money and get it back in a matter of months and effect big savings for years to come. F. C. Bond—This paper is of considerable importance in that it emphasizes a modern trend to operate ball mills at somewhat slower speeds than formerly. We have checked the data in the paper with that obtained

Jan 1, 1951

By Harlowe Hardinge, R. C. Ferguson

Oscar Johnson—In my opinion, the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. Comparing the entire groups of operators with those who have had the opportunity to make slow-speed mill studies, I think you will find the latter small in numbers. Most managers want the equipment worked to its maximum output. There are, however, some installations where plant and mill sizes are such that they can do the job with reduction of mill barrel speeds. The past and the present installations of the industry are laid out to get the most capacity for the least capital outlay. This is the case even with the plants of Chile Exploration, International Nickel, Morocco, and Anaconda, now under construction or being changed. The industry recognizes that most all equipment it buys today is good and can be depended upon for efficient performance. Under this scheme of things, I am doubtful that slow-speed ball mill operation will be generally applicable. With reference to the U. S. Bureau of Mines laboratory tests, I think table II could have been omitted. It is inconclusive as to maximum efficiency for the low-pulp level mill on hard ore. There should be no question about this point. However, data on mill speeds can be found to substantiate various theories as well as refute them. Gow, Guggenheim, Campbell and Coghill, in their paper on Ball Milling,&apos; believe their 2 x 2 ft laboratory mill reflects results that can be expected from large mills. If so, then referring to their table 11, they state, "The conclusion to be drawn from this second series is that high speed, not exceeding 72 pct of the critical, favors capacity, as before, but that with proper conditions of operation high speeds may give as good efficiency values as low speeds. In this case the efficiency values are nearly constant. A horizontal curve would indicate that the amount of grinding was directly proportional to the power expended, and these tests suggest that such a coildition can be made to exist in commercial operations." Table II (From Paper by Gow et a1)2 Speed. Pot Critical 32 42 52 62 72 82 Capacity: Surface tons per hr (65- mesh) 266 42.1 54.4 65.9 74.3 74.1 Surface tons per hr (200- mesh) 56.1 87.4 112.7 137.1 154.2 153.0 Efficiency: Surface tons per net hp hr (65-mesh) 35.7 36.3 36.3 35.4 34.3 32.3 Surface tons per net hp hr (200-mesh) 75.3 75.3 75.1 73.7 71.0 66.0 Ore in mill, 1.b. 98 100 100 113 122 165 The field performance data, table 111, represents much effort in its collection and preparation. But, one must realize that there are many variables that effect the efficiency of grinding mill operation, and too much must not be assumed as to the effect of some specific change. Possibly with changes in mill speed, the results might be more consistent by also a change in ball rationing, type of ball, volume of ball charge,. p.ulp level and amount of pulp in the mill, pulp consisting, design of liner, circulating load, etc. Also, changes in ore character must be reckoned with when evaluating grinding performance. At present the Climax Molybdenum Corp. is running at much reduced capacity. Mr. James Duggan informs me that at mill speeds of 17 rpm, they save a $0.025 per ton on liners and $0.025 per ton in power, but, if the demand for molybdenum increased, he would go back to higher speed to obtain maximum tonnage, as the values from the increased tonnage would far more than offset the one half saving at the slower speed. The Jnspiration ran a six months&apos; test between mills running 21 rpm and 23.5 rpm. The slower mills ground 10 pct less ore with a slight saving per ton, but when the reduced plant tonnage was checked back into the actual cost figures of concentration, the high-speed mills with their greater tonnage showed considerable advantage. To be convinced of possible practical results from the predictions in the conclusions, I think we would have to rely on the analysis of expert cost accountants to furnish the necessary proof figures. Hardinge and Ferguson are to be commended for the work in preparing this paper. I am convinced that our Massco engineers should go into higher speeds with our equipment. Harlowe Hardinge (authors&apos; reply)—For one, I heartily agree with Mr. Johnson&apos;s opening statement that the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. It was on this basis and for this reason the paper was written. Mr. Johnson, on the other hand, takes the position that, on the whole, low speeds are not justified from the economic standpoint, basing his principal reason on the fact that lower mill speeds cut mill capacities and hence reduce the gross income from the product produced. There is no denying this point. It is almost axiomatic. It is for this very reason that the overall advantage of lower mill speeds has been discounted and even overlooked. It was for this reason mainly that the paper was written in the first place. It is one thing to plan an efficient operation at the outset, basing one&apos;s figures on the tonnage requirements at the time, and it is quite another to be confronted with the problem of increasing the output of an existing installation at a minimum of capital expenditure. Economic consideration of a new installation is greatly influenced by referring to an old one. Too often, the analyst assumes that if this practice is followed in the new installation, one would not go wrong. It is just here that he may be wrong. Past practice and low capital expenditure are all too frequently given priority over the engineer&apos;s analysis of operating costs. When we are able to start fresh, we should give proper weight to other economic factors which do not exist in an old installation. It is these economic factors that make it possible to spend at the outset just a little more money and get it back in a matter of months and effect big savings for years to come. F. C. Bond—This paper is of considerable importance in that it emphasizes a modern trend to operate ball mills at somewhat slower speeds than formerly. We have checked the data in the paper with that obtained

Jan 1, 1951

By J. N. Hobstetter, J. J. Becker

Slip lines in deformed copper single crystals exhibit very pronounced cross-slip and clustering if the stress axes are not too far from <100>. This orientation dependence seems to persist whether or not attempts are made to reduce the bending constraints of ordinary mechanical tests. THE purpose of this paper is to report some microscopic features of the plastic deformation of copper single crystals. The material used was OFHC copper obtained from the American Brass Co. Single crystals about 3 in. long and 5/16 in. in diameter were made by lowering graphite crucibles containing this copper out of the hot zone of a vertical tubular furnace at a rate of 1 1/4 in. per hr. The furnace atmosphere was nitrogen. The orientations of the crystals were determined by the back-reflection Laue technique.&apos; The X-ray spots usually indicated a slight lineage structure of not more than a degree or two. The crystallography of slip is discussed in Schmid and Boas.&apos; The terms classical slip, cross-slip, and conjugate slip are used here with the same meanings as in ref. 3. Compression Specimen 17 (Fig. 1) was selected because the resolved shearing stresses on eight slip systems dif- fered at most by a factor of 1.2. It was hoped that in this situation such effects as cross-slip might be made more prominent. Two intersecting planes parallel to the stress axis were ground on the crystal, using optical abrasive on a lead lap. The large plane was approximately perpendicular to the plane of the axis and the primary slip direction. Its exact orientation was determined by X-ray. The smaller made an angle of 49" with the larger, measured by reflecting a small light source. The specimen was etched with nitric acid until its diameter had been reduced 0.010 in., and then was given a metallographic polish and very

Jan 1, 1954