Search Documents

By J. F. Wilson

An experimental investigation has been made of gas-driven slug displacements in a system of high gas saturation to evaluate the process for use in a California reservoir. Fluid compositions, temperature, pressure and core permeability duplicated reservoir conditions as closely as possible. The temperature was above the critical of the slug materials. The slug composition required for 100 per cent oil recovery in the linear flow systems was found to agree with that determined from equilibrium phase studies. A qualitative theory for the slug displacement of two-phase systems is proposed and found to be in general agreement with the observed flow behavior. The theory predicts that the length of the reservoir fluid-slug transition Zone will increase with increased initial gas saturation and decrease with increased oil swelling accompanying the composition change from reservoir oil to the critical composition. The precipitation of small amounts of an asphaltic phase during the formation of the transition zone had no adverse effects on the flow behavior of otherwise miscible systems. INTRODUCTION Despite the large number of recent publications relating to oil recovery by miscible displacement, little information is available concerning the behavior of crude oil-natural gas systems at conditions likely to be encountered in field application. The laboratory data reported here were obtained during an investigation of the possibility of using a gas-driven LPG slug in a partially depleted California reservoir. Seven gas-driven slug displacements employing slugs of different compositions and sizes were made in 26- to 27-ft long sandstone cores. The equilibrium phase behavior of the systems was also determined. The features of primary interest in this study are the following. 1. Data were obtained on the displacement of reservoir fluids at reservoir conditions. 2. A high gas saturation existed in the long cores at the start of the displacements. 3. The temperature of the studies was above the critical of the slug materials. 4. A comparison between the flow behavior and equilibrium phase behavior, as illustrated by a pseudo-ternary phase diagram, is afforded for a system of considerable complexity. THEORY Phase Behavior The use of the pseudo-ternary phase diagram to illustrate the phase behavior in miscible displacements has been discussed by Clark, Schultz and Shearin. Sie-vert, Dew and Conley and Arnold, Stone and Luffel' have presented both phase equilibrium and flow data for true ternary systems. For the true ternary, the application of the theory is straight-forward; for a reservoir system represented as a ternary, the theory undoubtedly gives a qualitatively correct picture. One purpose of this investigation was to see if the pseudo-ternary phase diagram could be used to predict with reasonable accuracy the conditions necessary for miscible displacements with actual reservoir systems. MiscIBLE Displacement of Two-Phase System A large number of papers "I3 have treated the miscible displacement of a single-phase fluid from both an experimental and a theoretical viewpoint. However, the normal field application of the process will be in a partially depleted reservoir. Often the state of the system will be such that the mobility of the gas phase is greater

By H. E. Hawkes, D. A. Barr

Time variations in the copper content of the sediments of streams draining mineralized areas were studied in two areas of contrasting climatic environment, one in northern and one in southern British Columbia. In each area, samples were collected and observations made of rainfall, stream discharge and air and water temperature at intervals throughout the summer season. Samples were analyzed for total and cold-extractable copper. Results showed a weak inverse relation between cold-extractable copper and discharge in two out of the three test sites in the southern area, and a decrease in ratio of COld-extractable to total copper over the duration of the test period at a highly anomalous site in the northern area. In suspended rock flour resulting from glacial erosion of mineralized rock in the northern area, virtually all the copper was found to be soluble in cold, dilute hydrochloric acid. None of the variations observed is sufficient to cause serious problems in geochemical sediment surveys. Systematic collection and trace analysis of stream sediments has seen wide application in recent years as a method of primary prospecting in primitive areas. Common practice is to collect fine-grained samples of sediment either from the active channel or from the flood plain near the channel. Samples are dried, sieved and the -80-mesh fraction analyzed after breakdown of the sample by a relatively strong attack, such as by fusion or by treatment with hot perchloric acid. Drying, sieving and rigorous chemical attack requires established facilities, either in a well equipped central laboratory or in base camp. Thus analysis for total metal involves a substantial delay from the time the samples are collected until the analytical data can be reported. An alternative system uses a cold aqueous extrac-tant in place of the hot acid or flux.4 Advantages of the cold-extraction techniques are that kits can be prepared for use directly at the sample site and that, in some problems, the patterns in cold-extractable metal, usually abbreviated cxMe, are more useful as ore guides than the patterns in total metal.' In the course of operational geochemical sediment surveys, a problem that has come up repeatedly is failure to reproduce anomalous values or patterns by resampling the same areas. The mystery of the vanishing anomaly has led to speculation as to whether there is a significant variation in the metal content of sediment samples with the weather or with the time of year. Review of the published literature shows that a number of experiments have been carried out on time variations in the metal content of stream water.1,2,5,7-9 The only published report on time variations in stream sediments that has come to the authors' attention, however, is by Govett,3 working in Northern Rhodesia.

Jan 1, 1963

By Paul H. Lu

Methods and results of measuring three basic parameters for ground stability control, ground pressure, strata movement, and geomechanical properties of mine rock are presented in this paper. It is found that these parameters can be measured in situ by simple and practical techniques with nonsophisticated and inexpensive instruments. Specifically, a drillhole dilation technique employing a cylindrical hydraulic borehole pressure cell (CPC) was used to determine the modulus of rigidity. Premining ground pressures were determined by pressure convergence tests with a combination of one CPC and two pre-encapsulated flat hydraulic borehole pressure cells (BPC) installed in a single drillhole. Abutment pressures and pillar loading were monitored with BPC's. Differential strata movements and bed separations were measured with self-recording 10-anchor-point extensometers. Roof-to-floor convergence was measured with self-recording convergence meters. Some applications of these in-situ-determined parameters to mine design and ground stability control are also discussed.

Jan 1, 1984

By L. A. Updegraff

Before discussing the application of capacitance for the measurement of moisture content in a moving stream of coal it might be well to first give a brief description of the process and then show how it can be applied to the coal industry. A capacitor may be described as a device having two conductors separated by an insulator, the conductors hereafter being designated as a test cell or test plates and the insulator as the dielectric. Capacitance, therefore, is a measure of the ability of a capacitor to store an electrical charge. Two basic factors that affect capacitance are the dimensions of the capacitor and the dielectric constant of the insulator. Capacitor dimensions which affect its capacity are the area A of the conductive surface, and the distance d between plates. Capacitance is inversely proportional to the distance between plates and directly proportional to area A, so if capacitance is indicated as C and the dielectric constant as K the equation for capacitance would be C = AK/d. The dielectric constant can be described as the ratio of the actual capacitance of any given material to that of a vacuum, which is unity. In industrial applications the area of the plates remains constant as also does the distance between them, leaving the dielectric constant as the only variable to affect the capacitance measurement. Figure 1 is a schematic diagram of an r-f excited capacitance bridge in which a test cell is part of the circuit. This bridge consists of four capacitors in two pairs connected across an a-c voltage source. In one side of the circuit the two capacitors are fixed but in the other side they are variable, one being the rebalance capacitor operated by the servo motor and the other the test plates between which the dielectric passes. Capacity of the plates is a function of the dielectric constant of the material between them and is measured at radio frequency. Within the recording instrument is an r-f oscillator and a 60 c ps modulator. The radio frequency signal is generated by the oscillator, modulated by a 60 cps wave, and sent to the bridge. Therefore the signal entering the capacitive bridge is a radio frequency carrier with a 60 cycle envelope, If the bridge is in balance as the signal enters there would be no voltage drop and so no output by the detector. As long as the dielectric constant remains the same the bridge will stay in balance. However, any change in the dielectric constant, which in this case would be a change in moisture content, would affect the bridge. Higher moisture increases the capacity of the test cell which causes less voltage to develop across it causing imbalance of the bridge. This in turn causes a radio frequency signal to appear at the detector. Output from the detector is a 60 cycle ripple which is in proportion to the imbalance of the circuit. A 60 cycle amplifier boosts the detector signal to enough power to drive the servo motor which positions the recording pen and also rotates the variable capacitor, to which it is mechanically connected, to bring the bridge back in balance. An increase in moisture causes the servo motor to rotate in one direction, but a decrease causes imbalance in the opposite direction, and thus rotates the motor in that direction. This brings the bridge back in balance and stops the motor. The bridge shown in Figure 1 has been modified so as to provide a wide range of adjustments. Coarse and fine span adjustments located in the recording instrument are set to govern the amount of pen movement for a given change in capacitance. A measuring head unit contains coarse and fine zero adjustments for

Jan 1, 1961

Jan 1, 1968

US 4,133,866-Selective recovery of the bound sodium content of red mud obtained in the production of alumina by the Bayer process The red mud is mixed with aqueous ferric sulfate, the resulting suspension stirred intensively at a temperature of 15-85°C and adjusted to a pH value of from 4.4 to 4 6, and the solids are removed. The clarified solution of sodium sulfate can be used directly for the leaching of additional bauxite T Lakatos, M Miskei, J Szolnoki, F. Toth, and L Revesz, assigned to Aluminiumipan Tervezo es Kutato Intezet, Almasfuzitoi Timfoldgyar, and MTA Geokemiai Kutatolaboratorium. Jan. 9, 1979. 3 pp (423-208). Filed: 10¬28-77 (846,588) Priority: Hungary, 10-29-76 (AU 364). US 4,145,398-Continuous digestion of bauxite with aqueous sodium hydroxide, with higher throughput in existing plants or the construction of smaller plants with equivalent capacity The ore suspension at a solids concentration of 1-6% by weight and temperature of 200-300°C is flowed through a digestion tube or nest of tubes at a velocity of preferably from 2 to 5 m/s and under a pressure of from 10 to 200 atm Heat is supplied by a fluid heat carrier flowing in countercurrent in a concentric outer tube. Preferably, some of the red mud is recycled to the digestion operation. L. Plass, assigned to Vereinigte Aluminium-Werke A.G Mar 20, 1979. 5 pp. (423-121) Filed: 2-27-76 (754,749) Same: British 1,437,548, dated May 26, 1976 Same Canadian 1,008,253, dated Apr 12, 1977. US 4,146,573-An aqueous slurry of red mud, formed in the Bayer process production of alumina from bauxite, can be solidified by treating the red mud with a described quaternary ammonium salt, continuing mixing until the red mud has set up to a rigid mass, and recovering the solidified concentrated red mud J Kane, assigned to Nalco Chemical Co Mar 27, 1979 4 pp (423-82). Filed 8-2-78 (930,251).

Jan 1, 1980

By H. W. Fleming, R. R. Brooks

The Clearwater Deposit, a small occurrence of massive-sulphide mineralization enclosed in an envelope of disseminated-sulphide mineralization, was discovered as a result of an aeroelectromagnetic survey in New Brunswick in 1955. Subsequently, additional flights were made over the deposit and various ground follow-up methods were employed to ascertain the nature of their response. All methods proved to be capable of indicating the occurrence with varying degrees of precision. This paper is a presentation and a discussion of the magnetic and electromagnetic data, both airborne and ground, and the self-potential data obtained over this deposit. The attention of Canadian mining exploration companies was initially focussed on New Brunswick by the discovery, in 1953, of the Brunswick ore body. Ground electromagnetic surveys were of considerable assistance in locating and developing this deposit. In the following year, 1954, the Heath Steele base-metal deposits were discovered by employing an airborne electromagnetic device and ground electromagnetic surveys to follow-up the airborne indications. These discoveries demonstrated clearly that both airborne and ground electromagnetic techniques were applicable for locating the near-surface deposits of massive sulphides present in this region. Airborne electromagnetic equipment became available on a contract basis through Aeromagnetic Surveys Limited early in 1955 and was used extensively thereafter throughout a large portion of northern New Brunswick. It was as a result of one of these surveys with Aeromagnetic Surveys Limited equipment in the summer of 1955 that the Clearwater Deposit was detected. The airborne anomaly was located on the ground by means of an electromagnetic survey using a Swedish Slingram unit. During 1956, the region was investigated more thoroughly- in the hope that other sulphide bodies might be located. Airborne electromagnetic coverage was extended and the Clearwater Deposit itself was used as a testing ground for the various methods and types of equipment currently in use in New Brunswick. In this paper com prative data are presented for the airborne magnetic, airborne electromagnetic, ground magnetic and ground electromagnetic surveys over this deposit. The ground electromagnetic instruments used were the McPhar vertical-loop unit and the Slingram and Boliden horizontal-loop units. Self-potential surveys were carried out with a McPhar unit. From the geophysical point of view, all ground electrical methods employed indicated the presence and the extent of the massive-sulphide mineralization with a good degree of accuracy. The horizontal-loop methods however, defined the contacts more precisely as is to be expected when dealing with a flatly-dipping

Jan 1, 1961

By E. T. Turkdogan, P. Grieveson, J. F. Beisler

Jan 1, 1963

By A. L. Sweetser

EXPERIENCE has shown how difficult it is to obtain information regarding laboratory-tests in connection with the chlorination-process for the extraction of gold from its ores, and I therefore present the following method, somewhat in detail, for the benefit of those who may desire to pursue research work in this field. The ore chosen was a partly-decomposed porphyry, extremely siliceous and comparatively soft, and of an average value per ton of from $25 to $26 in gold and $0.68 in silver. The chemical analysis gave : Fe2O3, 3.35; FeS, 1.5; MnO2, 0.75; ZnCO3, 4; Al2O3, 3.20; H2O, 0.7; SiO2 and insol., 83.50 per cent. The ore, first crushed to pass a 5-mesh screen, was coned and quartered until a 45-lb. sample was obtained. Samples for assay and analysis, taken from this lot by means of riffles, were crushed to pass a 100-mesh screen. The original sample was divided into 10-lb. lots, of which one was crushed to pass a 10-mesh screen; another through a 12-; the third through a 20-, .and the last through a 30-mesh screen. Because of the production of an excessive quantity of fine material it was deemed inexpedient to crush finer than 30-mesh size-a decision the wisdom of which is proved by the data in Table I., showing the increasing ratio of slimes, in proportion as the ore is crushed finer. In order to determine the percentage of fines in the sizes of mesh selected, a weighed sample of ore was taken from each mesh, and a sample from the 10-mesh lot was passed successively through 20-, 40- and 100-mesh screens, and the percentage remaining on each screen determined. This process was repeated with the 12-, 20- and 30-mesh lots, with the results given in Table I.

Sep 1, 1907

By K. C. Ko, D. A. Pifer

The theory of probability with respect to the failure of structures is discussed. It is shown that the probability of safety, probability of failure, and factor of safety are directly related to each other and that as standard deviation approaches zero, the probability curves approach a unit step function which can be interpreted as the conventional factor of safety. The factor of safety is numerically the ratio of the load to the strength of the material at a particular point or plane in an engineering structure. Mathematically, it can be illustrated as a unit step function undefined at the point where the factor of safety is one (Fig. 1). The uncertainty of variation of soil and rock strengths require factors of safety much higher than those used in other engineering structures. The factors of safety used are generally determined from past experiences with similar structures. However, the factors thus determined do not have any theoretical meaning or do not indicate any relationship to actual safety.' It seems, therefore, logical to develop a system with a sound theoretical basis to obtain a more suitable factor of safety for structures. An application of elementary theory of probability indicates that it is possible to relate this number to theoretical and practical engineering facts.

Jan 1, 1971

By D. K. Deardorff, Haruo Kato

D. K. Deardorff and Haruo Kato (U. S. Bureau of Mines)—We wish to refute the 1875" 20°C value that Giessen, et al., report as the transformation temperature of hafnium. Although these authors state that their work along this line will be reported later, we can't leave their value undiscussed, for we believe it to be 125°C too high. Our value of 1750° 20°C, which the authors mention, has been substantiated in our laboratories by the use of three other methods. The first method of substantiation was by heating and cooling curves using a hafnium/tungsten thermocouple, the couple having first been calibrated against a t/Pt-10 pct Rh couple. The second method was by quenching and metallography of dilute Hf-Ta alloys. The third cussion, it may be pointed out that the observations of Rogers referred to large unidirectional strains where the internal cracks or voids appeared only after a strain of 32 pct or more. On the contrary the internal fissures observed, as a result of fatigue cycling, occurred for a total extension of some 5 pct and furthermore followed the directions of the slip zones. Finally, it is not our contention, as implied in Dr. Alden's last paragraph, that the tensile stress is an important factor in crack propagation. Indeed, in connection with the reference to the companion report, special note is made of the fact that "Deformation was apparently concentrated in grains which have a slip plane nearly perpendicular to the specimen axis and thus near the plane of maximum applied shear." This dependence of the growth of fissures on the orientation of the slip planes with respect to the direction of maximum applied shear is clearly shown in work on the torsional cycling of single crystals which has been submitted for publication. method was by heating and cooling curves with W/W-26 pct Re thermocouple. Counting the original resistometric method, four different methods have yielded 1750" 20°C as the transformation temperature of hafnium. All our work on determination of the hafnium transformation temperature has shown that the specimen under test must be quickly heated to and through the transformation temperature if the lowest possible transformation value is to be determined; otherwise a higher value not representative of pure hafnium will result. Speed was emphasized in all methods. In our resistometric work the corresponding voltage, amperage, and temperature readings were taken quickly and the transformation temperature was usually reached within 5 min total heating time. In the thermal analysis work involving Hf/W or W/W-26 pct Re thermocouples the transformation temperature was attained within three minutes total heating time, this time being less because the two variables were

Jan 1, 1963

By P. H. Metzger, D. W. Fuerstenau

The activation of sphalerite was found to occur at a much lower rate with Pb++ then with Cut++ or Ag+. To prevent activation with Pb++, the ratio [m in solution must approximate 103. An example is given illustrating how this condition is met in practice through the addition of zinc sulfate and soda ash. In selective lead-zinc flotation, the mill operator, especially the one who is concentrating a partially oxidized ore, often must add zinc sulfate and/or soda ash for effective depression of the sphalerite. In the present paper the authors show how this practice prevents the activation of sphalerite in the presence of Pb++. A number of years ago Gaudin (1) postulated that Zn++ might control the activation of sphalerite with Pb++ through competitive adsorption. However, recent experimentation has shown the activation of sphalerite with Ag+ and Cut++ to be a chemical reaction in which silver or copper ions replace zinc in the sphalerite lattice through the formation of a more insoluble sul-fide (2,3,4) Thus, if activation with Pb++ is similar to that with Ag+ or Cu t+, zinc salts should control the activation of sphalerite not through competitive adsorption but because the ratio of [zn++/Pb++] in solution regulates the extent of the chemical exchange between Zn++ and Pb++ in the solid phase. The objective of this investigation has been to study the kinetics and equilibrium conditions for the uptake of Pb++ by sphalerite and to investigate the prevention of lead activation with zinc salts. BASIC PRINCIPLES Sphalerite activation has been shown to be a replacement reaction wherein a less soluble compound is formed at the expense of the more soluble zinc sul-fide (2,3,4) For example, if sphalerite is placed in an aqueous silver nitrate solution, ZnS gives to the solution more S= than can exist together with Ag+, and hence the following reaction takes place: ZnS + 2 Ag+? Ag2 S + Zn ++; k = [zn ++]/[Ag ++]2 = 10 26 (1) Therefore, ZnS will dissolve in the presence of Ag+ and activation of sphalerite with Ag+ will proceed after monolayer coverage by solid state diffusion until equilibrium conditions are reached in the system (2, 4) Because of the large difference in the solubility of ZnS and Ag2S, zinc salts cannot affect the reaction unless a complexing agent, such as cyanide ions, is present to complex Ag+ more tightly than Zn++ . By complexing Ag+ and Zn++ in solution, the uptake of Ag+ by sphalerite can be regulated by controlling the ratio m. . Experimentally (2) it was found that the activation of sphalerite by Ag+ could be prevented through the addition of NaCN if this ratio reached a value of approximately 10 26. The mechanism of sphalerite activation with copper salts is given by the following reactions: ZnS + Cu ++ ? CuS + Zn + + ; (2) k = [Zn++]/[Cu++] = 10 11 ZnS + Cu + ? Cu2S+ Zn++; (3) Experimentally Mao (3) found that the activation of sphalerite with Cu++ or Cu + was prevented if the ratios expressed in Equations 2 and 3 were approximately l09 and l022, respectively, with cyanide ions as the deactivator. Although zinc salts do not affect the activation of sphalerite with silver or copper ions in the absence of a complexing agent, activation with lead ions theoretically can be controlled by the addition of zinc salts because of the relatively small differences between the solubility of ZnS and PbS (5). Equilibrium

Jan 1, 1961

By P. F. Allen

WITH capacity of 51,000 tpd, the Morenci concentrator produces approximately 49,000 tons of tailing for final deposition. Disposal involves distribution of thickened tailing to dams in such a manner that solids can be used for dam construction and water can be impounded for reclamation. During early operation, although tonnage treated was lower, it was necessary to use orthodox disposal practices in the areas available for tailing. Trestles mounted on a series of dams, constructed of borrow material, carried the pipelines from which tailing were spigoted behind the dams. When adequate disposal areas were finally established, it became desirable to look for more efficient methods. The idea of placing the distribution pipe or manifold directly on the crest of the dam was advanced in 1945. After a period of testing, that procedure in modified form replaced the older trestle arrangement. Marked economies resulted, and time required to prepare dams for succeeding storage cycles was greatly reduced. The tailing disposal area for the Morenci concentrator lies south and southwest of the concentrator building. Ample storage space is available. A wide valley contains three sharply defined ravines lying on an average slope of 4 pct. The more central of these ravines, and the largest of the three, is known as Morenci canyon, which provides substantially more tailing storage area than the other two. Stargo canyon lies to the west; the other is appropriately named East canyon. Total area of the tailing disposal site is nearly 31/4 sq miles, or about 2000 acres. The storage area in use was somewhat more than 850 acres at the end of 1954, or 16 acres per 1000 tons of tailing to be stored daily. At the present time none of the east side dams are in regular use but they are available in emergency. There are five dams on the west side (in Morenci and Stargo canyons) as well as two auxiliary dams adjacent to No. 4 West and No. 5 West. This has made it possible to concentrate men and equipment in a smaller area with consequent savings in both manpower and machinery. Tailing Thickening: Tailing from the flotation process reaches the thickeners with a solid content of about 18 pct. The launder carrying this pulp is subdivided at a central point into seven launders carrying a proportional share to each of seven tailing thickeners, which are located in Morenci canyon close to the concentrator. Five of these thickeners are 300 ft diam and two are 325 ft diam. Thickeners are of the peripheral traction type and rakes travel at the rate of one revolution in 37 to 39 min. The entire installation provides 500,000 sq ft of settling area, or approximately 101/2 sq ft per ton of tailing to be thickened daily.

Jan 1, 1957

By R. S. French, W. R. Hibbard

FOR tensile deformation, if the stress value is defined by the ratio of the load to the actual area, and the strain value by the natural logarithm of the ratio of the immediate length to the original gauge length of the sample, the resulting data when plotted with logarithmic coordinates result in a linear relation extending from the initial plastic yielding through the maximum load and in some cases, such as for copper and brass, to fracture'.'. The normal form of the curve, therefore, is a parabola, satisfying the following equation: S = Kem [1] where S and e represent true stress and strain, K is a constant, and m is a coefficient evaluating the slope of the curve and designated therefore as the strain hardening coefficient. Hollomon² has reported that this coefficient is a function of the yield strength as effected by grain size in alpha brass, and the carbon content and heat treatment of steel. In the case of steel, the value of the proportionality constant is a function of the carbon content. It was further shown in that paper2 and also by Low and Prater -hat, if the power relation between stress and strain remains valid, the strain hardening coefficient m, is equal to the strain at the maximum or necking load. Thus, an added significant feature is that this coefficient may serve as an index of the capacity for deformation prior to localized necking and subsequent fracture, e.g. drawability. The constant K may be defined as the strength of the material at unit strain. Together the K constant and the m coefficient describe an alloy's physical properties as far as strength and ductility are concerned for a particular yield strength and, in the case of steel, a particular carbon content. The work of Lacy and Gensamer4 gives data on alloy ferrites from which very close estimates of the strength of ternary and higher iron alloys have been made. It was the purpose of this investigation to develop similar data for commercial copper base alpha solid solution alloys. Preparation of Specimens Commercial binary alloys of copper with aluminum, beryllium, cadmium, nickel, silicon, tin and zinc were investigated. In addition, laboratory castings were made of a 1 pct silicon alloy and a 2 pct aluminum alloy to complete these particular series. Two types of copper were used, oxygen free OFHC and tough pitch FC. The analyses of these alloys are shown in table I. Standard ASTM sheet tensile specimens were used to determine the usual physical properties of each alloy and to obtain stress data at strains from 0.0005 to 0.01. Small (1/4 in. x 3 in. x tk.) samples

Jan 1, 1951

By Richard A. Kesler, W. Michael Reed

Grindability or resistance to fine comminution is the fundamental issue involved in the application and sizing of grinding mills. Over the years, many theories for determining the amount of energy required for size reduction to a specified fineness have been proposed. The first published theory, introduced by P. R. von Rittinger in 1867, stated that the energy required for crushing or grinding is proportional to the increase in surface area produced. The surface area of a ton of particles of diameter (d) is proportional to (1/d), therefore the work input per ton for particles of diameter (d) would be proportional to (1/d). The second significant theory is that of F. Kick published in 1885. Kick said that the work required is proportional to the reduction in volume of the particles concerned. If (f) is the diameter of the feed particles and (p) is the diameter of the product particles, the work input relationship would be: [W =Ioq(f/p) 9] The "Third Theory" of F.C. Bond, introduced in 1951, states that the work required is proportional to the length of the new crack tips produced in particle breakage during crushing or grinding and equals work represented by the product minus that represented by the feed. This takes the form: [W=]

Jan 1, 1982

By B. Wilshire, P. W. Davis

It has been shown that grain-boundary migration during high-temperature creep can reduce or even prevent the formation of intercrystalline voids, giving a considerable increase in ductility.' A similar observation has been made in a recent investigation of the creep properties of various grades of nickel and nickel alloys. The results can be illustrated by the observations made on: a) Pure vacuum-cast nickel (99.993 pct Ni) b) Impure vacuum-cast nickel (99.97 pct Ni) c) Pure nickel containing internal voids (produced by a process of intering). d) A substitutional solid solution alloy of pure nickel containing 1.16 pct Sn. All the materials were given a high-temperature anneal (>850°C) to produce a stable grain size of 7 to 10 grains per linear mm. The apparatus and techniques used to obtain the present results have been described elsewhere.' In this series, grain growth was observed only in the highest-purity, vacuum-cast metal. Thus we may consider that in the other materials grain-boundary migration was prevented by either preexisting voids or solute atoms. The effect of migration on the creep ductility of the above materials can be seen from Fig. 1, which

Jan 1, 1962

By Frederick Laist

AFTER a series of experiments covering a period of about three years, ending from the spring of 19iJ.2 to the spring of 1915, a 2,000-ton leaching plant for the treatment of the accumulated copper concentrator tailing was built and put into operation. During the experimental period, the first step was that of laboratory experiments or beaker leaches. The results on this small scale were so satisfactory that a small operating plant, capable of handling 5 tons of roasted tailing per day, was installed. Again, the results proved satisfactory and an 80­ton plant was built and operated continuously from August until February, 1913. In this plant, full-sized roasting and leaching units were

Jan 8, 1916

By A. L. Sweetser

Experience has shown how difficult it is to obtain information regarding laboratory-tests in connection with the chlorina-tion-process for the extraction of gold from its ores, and I therefore present the following method, somewhat in detail, for the benefit of those who may desire to pursue research work in this field. The ore chosen was a partly-decomposed porphyry, extremely siliceous and comparatively soft, and of an average value per ton of from $25 to $26 in gold and $0.68 in silver. The chemical analysis gave: Fe,O,, 3.35; FeS, 1.5; MnO,, 0.75; ZuCO,, 4; A1,0,, 3.20; H,O, 0.7 ; SiO, and insol., 83.50 per cent. The ore, first crushed to pass a 5-mesh screen, was coned and quartered until a 45-lb. sample was obtained. Samples for assay and analysis, taken from this lot by means of riffles, were crushed to pass a 100-mesh screen. The original sample was divided into 10-lb. lots, of which one was crushed to pass a 10-mesh screen; another through a 12-; the third through a 20-, and the last through a 30-mesh screen. Because of the production of an excessive quantity of fine material it was deemed inexpedient to crush finer than 30-mesh size—a decision the wisdom of which is proved by the data in Table I., showing the increasing ratio of slimes, in proportion as the ore is crushed finer. In order to determine the percentage of fines in the sizes of mesh selected, a weighed sample of ore was taken from each mesh, and a sample from the 10-mesh lot was passed successively through 20-, 40- and 100-mesh screens, and the percentage remaining on each screen determined. This process was repeated with the 12-, 20- and 30-mesh lots, with the results given in Table I.

Jan 1, 1908

By Frederick Laist

I. INTRODUCTION The new slime-concentrating plant at the Washoe Reduction Works, Anaconda, was put into operation during March, 1914. This plant, which has a capacity of 26,000,000 gal. of slime pulp carrying 2,500 tons. of solid matter per day, consists of Dorr thickeners and Anaconda multiple-deck slime concentrators.' This plant is the culmination of a great deal of experimental work extending over a considerable period of time, which work will be described briefly in the following pages.

Jan 8, 1914

By A. C. Lane

Relations de la profondeur de plissement avec la gravita-tion et la hauteur des montagnes dans les Alpes. Par A. Heim (Zurich) 50me Anniversaire, Livre Jubilaire Soc. Geol. De Belgique, Rome, Fascicule 1, 17 to 28. Measurements show a negative anomaly, less densities of .the material below sea level. The author expresses it in terms of the thickness of rocks of an arbitrary density, 2.4, which might be considered wanting. The accordant heights of the summits, the depths of the folds, the deficiency in .gravity, and denudation he finds to be connected. The Alps float on the lightness of the folds of "sal" of weight 2.6 to 2.75 plunged into the heavier "Sima" according to a for-mula: P = h (2.7/2.8-2.7) where - P is the depth of fold-ing below sea level; 2.7 is the weight of the material accu-mulated in folding; 2.8 is the weight of the material dis-placed by it; and h is the mean height of the mountainous regions. For instance, between the valley of Saar and the Val de Bagne in Valais the depth of the folds according to Ar-gand's profiles is between 30 and 40 kilometers. The loss of gravity has been estimated in this region as 1450 X 2.4 = 3480 in units of weight. Obviously errors in the densities would profoundly affect the estimates of the thickness of folding, but his depths of folds are obtained from sections, and from them he works back to the densities. Of course other densities might be placed in the formula. Zur Dichte bestimmung von Tonen. By J. Koenigsberger, Berg u. Hüttenmannisches Jahrbuch, 75, I. Discusses Dr. B. Wilser's investigations as to the best way of obtaining the weight of rocks per unit volume. The use of mercury for rocks affected by water as there recom-mended may easily give too large volumes unless 1 to 3 atm. pressure is used. Thick machine oil is recommended for large lumps of clay.

Jan 4, 1928