Search Documents

By P. C. J. Gallagher

A number of recmt determinations for the ratio of extrinsic to intrinsic stacking fault energy in fcc solid solutions are examined. Some of these arise from incomplete analyses which can yield only approxi?nate values for the ratio. Reliable results, on the other hand, obtained using extrinsic-intrinsic fault pairs, show that the extrinsic and intrinsic fault energies are essentially equal in several materials. There is some reason to believe that this finding is of general applicability to fcc elements and alloys. A wide range of values has been obtained for the relative magnitudes of the extrinsic and intrinsic stacking fault energies (yext and yint, respectively) in recently published studies in a variety of materials. In contrast, Hirth and Lothe' using a central force model have shown that out to tenth nearest-neighbor interactions the perturbation in energy caused by both types of fault is the same. Although the model used is not completely valid in metals, there is nevertheless some indication that marked variations of yext/nnt should not be observed from one material to another. In early work in Cu-A1, Cu-Ge, Ni-Co, and stainless steel all the deformation faults observed in the electron microscope were found to be intrinsic in nature, which led to an attitude that the extrinsic fault energy must be considerably greater than the intrinsic. Extrinsic faulting arising from deformation has, however, more recently been directly observed in Au-4.8 at. pct n;~ Ag-6 at. pct Sn and Ag-8 at. pct sn; Ag-7.5 at. pct In and Ag-11.8 at. pct 1n;"' pure silwer and Ag-0.5 at. pct ~n;' and Cu-22 at. pct Zn, Cu-30 at. pct Zn, and Cu-7.5 at. pct ~1.l' Multilayer loops containing extrinsic faulting have also been observed in quenched aluminum." While peak asymmetries in X-ray faulting probability studies were generally attributed to the presence of twins,Lelel2 has recently reinterpreted earlier X-ray data in Ag-Sb alloysU in terms of the presence of extrinsic faulting. The determinations of yeXt/yint made from the above studies are shown in Table I, with a brief description of the techniques employed. A number of the methods utilized are deficient in one or more respects, and the reliability of the values listed will be discussed. ~ele'~ recognizes that his approximate determinations of yext/yint assumes equal numbers of extrin-sically and intrinsically faulted dislocations. It is well-known, however, that such an assumption is not at all justified since extrinsic faulting has but rarely been observed in samples studied in the electron microscope. The only conclusion that should be drawn from the X-ray results at present is that the total intrinsic scattering cross section (i.e., the product of the width of the intrinsically faulted dislocations with their density) is approximately ten times greater than for extrinsic faulting in these particular samples. An important point is that the relative magnitudes of the energies cannot be inferred from results of this type, unless the intrinsic and extrinsic faults form with equal ease. One must recognize that, although a formation barrier may restrict the amount of extrinsic faulting which occurs, this in no way implies that the extrinsic and intrinsic energies should be different. It is unlikely that a worthwhile estimate of the relative densities of extrinsically and intrinsically faulted dislocations can be made at the high deformations present in X-ray samples. ~oretto,'~ from a statistical argument applied to the nonobservation of extrinsically faulted tetrahedra out of a large sample, concluded that yeXt/yint could not be less than -4.5. However, the present author feels that a high-energy formation barrier as just supposed also explains this finding satisfactorily and that no conclusion can possibly be drawn concerning the actual extrinsic stacking fault energy. The same argument also serves to explain the fact that extrinsic faulting has been relatively little observed in the electron microscope. Extrinsic-intrinsic node pairs and isolated extrinsic nodes were first reported by Loretto~ and subsequently by Ives and Ruff,' Gallaher,' and Gallagher and Wash-burn.' Ives and Ruff' found a wide spread in the ratio of extrinsically to intrinsically faulted area in the node pairs they observed, and drew the very tentative conclusion that yeXt/yint 2 2. They recognized that a straightforward comparison of the size of the faulted areas could provide no more than a qualitative result without a theoretical analysis of the dislocation geometry associated with extrinsic faulting. A theoretical

Jan 1, 1969

By Frederic Dewey

HAVING shown1 the difficulty of assaying so-called cyanide bullion and the extreme variations often found in the results, an investigation was undertaken to discover if possible the causes of these variations by a series of tests upon the specific action of various metals during cupellation. Zinc.-In order to test the effect of zinc, 48 assays were made in sets of 6, 2 rows of 3. The charge for the middle cupels consisted of 500+ mg. Au, 1,125 mg. Ag, 10 mg. Cu. To the end cupels 50, 75, 100 and 125 mg. Zn were added, and a set of each proportion was cupelled with 4 and 8 grants Pb. The cupels were assayed and showed the following gold contents in milligrams, the figures being arranged as the cupels stood in the muffle: TABLE 1 50 Mg. Zn 75 Dig. Zn 100 Mg. Zn 125 Mg. Zn 4 grams, Pb 0.2S 0.25 0.2S 0:29 0.27 0.34 0.33 0.28 0.41 0.31 0:30 0.36 0.30 0.33 0.34 0.31 0.31 0.29 0.35 0.37 0.42 0.41' 0.34 0.38 8 grams, Pb 0.40 0.43 0.42 0.38 0.36 0.43 0.35 0.34 0.41 0.33 0.37 0.37 0.54 0.17 0.59 0.44 0.43 0.43 0.38 0.39 0.41 0.57 0.38 0.46 _ In many instances the zinc does not appear to affect the cupel gold, but various exceptions are apparent, generally in the cupels in the back row. With 100 and 125 mg. Zn, in some cases the Zn burned with its characteristic flame before it could alloy with the other metals. Also, less fusible oxidized lumps were observed during the cupellation and some cupels showed a scum. In order to lessen the premature burning out of the Zn, an alloy of 2 parts Ag to 1 part. Zn was used. A uniform charge of 500,+ mg. Au,

Jan 7, 1917

By Magnus Troilius

The heat-calculations of gas-analyses involve cumbrous multiplications, which are apt to lead into errors. The foliowing tables and formulae have been found useful as facilitating such calculations, and therefore I hope that they will be of interest to some of the members. By "heat-unit" will, in the following, be understood the amount of heat required to raise the temperature of 1 kilogram of water l° Cent. All the tables refer to cubic meters at O0 and 760 mm. pressure. The following gas is chosen as an example: C02, - 4.0 vol. per cent. co, = 20.0 " CHI, - 3.5 " H, - 7.0 " N, - 65.5 " " 100.0

Jan 1, 1884

By G. H. Fancher

Improving economic conditions are reflected in the statistical picture of the petroleum and natural gas industry for 1933. Prices were better, demand was greater and the volume of production increased. The increase in the production of gas has been due mainly to the utilization of outlets to the new prolific gas fields of Potter and Tioga counties; of oil, to the growing demand for Pennsylvania grade lubricants. It should be emphasized that nowhere is volume of production more subject to control due to the extensive use of secondary methods of recovery and regional peculiarities than in Pennsylvania. A summary of developments in production for Pennsylvania in 1933 of necessity is brief. The data listed in Table 1 are all too few in number and not all that is desirable from the standpoint of accuracy. No state agency for the collection of data exists, no reports are compulsory. Nevertheless, because of the hearty cooperation of many individuals and public spirited corporations, it is believed that the data are as reliable as are obtainable at the present time. Furthermore, records of the past too often are lost, were never in existence or are fragmentary, to say the least. Illustrative of the condition is the fact that no thorough study of the oil and gas-producing regions has ever been made. The publications of the Pennsylvania Topographic and Geologic Survey upon the subject are noteworthy and valuable, especially the most recent one.' The Survey has been handicapped in the work by lack of time, personnel and funds in addition to the difficulties mentioned previously. It is obvious, therefore, that Table 1 cannot be completed for Pennsylvania. The data simply are not in existence. Officially there are 328 oil and gas pools or fields known by name and 58 distinct sands or horizons, one or more of which are productive of oil and gas in the various pools, but reliable data for only three general regions could be assembled.

Jan 1, 1934

By M. Hayri Erten

In this research the possibility of pelletizing high grade fluorsoar fines or flotation concentrates with the use of calcined colemanite as binder is investigated, and the room temperature and elevated temperature strengths of these pellets are compared with those of pellets which are obtained by using bentonite as binder. Pellets of 10-12 mm. size and having 10% calcined colemanite showed a much higher room temperature strength than those containing 5% benonite, both being endurated at 1000°C for 15 minutes. However, when the same batch of pellets were tested at elevated temperatures of 250º to 500°C, bentonite gave better results. X-ray tests showed that in the pellets endurated at 1000°C for 15 minutes the original crystal structure of fluorite mineral is preserved.

Jan 1, 1977

By R. A. Graham, R. W. Rohde, J. R. Holland

In a shock wave compression study of a martensitic Fe-30 pct Ni alloy, Graham, Anderson, and Holland' found a region of unusual compressibility extending from a few kilobars up to about 20 kbars. This region was characterized by a continuously decreasing shock wave velocity with increasing stress. In this note, we report the results of a study initiated to determine the source of this unusual compressibility. In earlier shock-loading experiments on martensitic Fe-30 pct Ni, Loree et a1.' determined that a phase change occurred at about 80 kbars. Subsequently, Bowden and elly found that samples of a similar material shock-loaded at about 100 kbars experienced a martensite-to-austenite transition. Their crystal-lographic analysis showed the transition was a direct reversal of the established martensite system to the austenite phase. The shock loading in the present experiments was accomplished by precisely controlled plane impact between two discs of the sample material. This configuration created a state of uniaxial strain in the two the front of a projectile which was accelerated to various velocities. Planarity between the impacting discs was controlled to 5 x 10-4 rad, and impact velocities were measured to 0.5 pct. From a knowledge of the Hugoniot relationships of the material and the impact velocity, the shock-wave stress can be calculated. Samples were shocked at 18, 50, 70, and 100 kbars. The specimen discs shocked at 18 and 50 kbars were instrumented with quartz gages to observe the stress time profile. A more detailed description of the experiment has been given previously.4 The shock-loaded specimens were recovered intact by decelerating them in a catcher filled with soft wood. Discs of Fe-30 pct Ni nominally 12.7 mm thick and 64 mm in diam were cut from bar stock. Chemical analysis of the material provided the following composition in weight percents: 29.5 Ni, 0.50 Mn, 0.21 Si, and 0.10 C, with traces of Cr, Cu, Mo, Al, and Co. The discs were austenitized at 650° C for 2 hr at a pressure of less than l0-' torr, and furnace-cooled. Martensite was then produced by quenching the discs at -196" and holding 168 hr. The initial martensitic structure formed is shown in Fig. l(a). Typical microstructures of samples shock-loaded at 18 and 100 kbars are shown in Figs. l(b) and l(c). The banded structure with the austenite regions running parallel to the shock propagation direction was characteristic of samples shock-loaded at all stresses. No such banding was found in samples that were not shock-loaded. Comparison of Figs. l(b) and l(c) shows that, although under the optical microscope the two microstructures are quite similar, the martensite plates of the specimen shocked at 100 kbars etched in a distinctly different manner. This unique etching behavior of martensite in samples shock-loaded above the 80 kbar transition point has also been observed by Leslie el al.' These investigators determined from X-ray and electron microscope studies that fcc martensite, similar in appearance to normal bcc martensite, had been formed under shock loading. A quantitative determination of the amount of austenite present after shock loading was made by X-ray techniques. Both the methods of Lindren' and Miller' were utilized. The results are shown in Table I. The error limits are those experimentally observed from two independent analyses of each sample and represent the precision of the experiment. The absolute error, which should be similar for each sample, is believed to be about 10 pct. It is seen that as the shock stress increases the amount of austenite present also increases. On the basis of the X-ray and microscopic observations, we conclude that shock loading below the 80 kbar ersal will initiate a martensitic reversal: the amount of reversal that occurs increases with in-

Jan 1, 1969

By A. Beeby Thompson

ALTHOUGH the exclusion of foreigners and private owners from participation in the development of the Russian oil fields prevents first-hand information being obtained, both official and private news indicate a growing appreciation of the value of the country's oil resources. Notwithstanding the suppression of that initiative and energy which only ambition can adequately stimulate, the industry is progressing and exports of products are assuming an importance that cannot be disregarded as an economic factor in the world's oil business. The following notes and observations must be regarded mainly as the views of one who has closely followed the fortunes of Russian oil, when considering the changes that have taken place in geological knowledge and oil-field technique, which have so profoundly modified oil-fields methods. Russia is fortunate in having retained the services of a few scientists and technologists whose devotion to science has superseded their personal inclination, and to these few men must be attributed the slow, but nevertheless striking, progress that has been made. The productive oil fields of Russia are centered around the Caspian Sea which, with its connected river system, constitutes such an ideal means of internal distribution for products. From the group of oil fields of which the city of Baku forms a center, oil is pumped to Black town, a suburb of Baku, where all the refineries are situated. The next important group of oil fields is located in the Terek district near Grosny, where refineries are erected and the products are piped or carried by tank cars to Petrovsk for the internal Russian market, or sent to the Black Sea by rail. A third oil field is spread over the province of Uralsk, north of the Caspian Sea, the main port of outlet being Gourief, at the mouth of the River Ural. In Trans-Caspia there are two oil-field centers, one near. Krasnovodsk on Chelekan Island, and one in Central Asia at Ferghana. The product of the former fields is transported to Baku for treatment, while the output of the Turkestan field is refined and consumed locally, mainly by the railway.

Jan 3, 1925

By Ronald C. Whiting

SINCE the advent of what has been aptly called "chemical flotation," about 1920, the number and complexity of the various chemicals used in practice have increased enormously. Over 300 patents have been issued dealing exclusively with flotation reagents, and many of these embrace from two or three up to a score or more of specific compounds. The exact number of compounds actually finding a practical use in flotation would be difficult to determine, though the U. S. Bureau of Mines gives an annual list by groups.

Jan 1, 1938

By Persifor Frazer

The accompanying diagrams represent a lamp provided with certain improvements which render it more serviceable for the use of the engineer or other mining official who is often compelled to visit several mines a day remote from each other, and may be called on to use the magnetic needle in any or all of them. These requirements demand that the material of which it is made should be copper, and that it should be capable of being closed oiltight, for emptying and refilling the lamp at each mine would be a less expeditious as well as a less cleanly process, and transporting a lamp of the ordinary kind over rough roads on horseback or in wagon, would result in spilling the greater part of its contents. The general form of the lamp, including the false back to keep

Jan 1, 1882

By J. J. Kramer, G. W. Wiener, K. Foster

The effects of the primary grain size and sheet thickness on the secondary growth rates of grains with (100) surface planes were studied in 3 pct Si-Fe sheets. This secondary grain growth was carried out under conditions in which the {100} plane had the lowest surface free energy. The value of the surface energy difference, between the (100) plane and the random matrix planes was found to he only about 3 pct of the grain boundary energy, indicating that most of the driving force for secondary growth is supplzed by grain boundary energy. A method for obtaining cube texture in 3 pct Si-Fe sheets by a secondary recrystallization process has been reported.' It has been demonstrated that a difference in surface free energy between the (100) plane and other planes is responsible for this growth, where the (100) plane has the lowest surface energy. A semiquantitative relation has been derived for secondary grain growth in sheets where primary grain growth has proceeded until the grains have grown through the sheet and the average grain diameter in the plane of the sheet is from one to two times the sheet thickness. Then, the linear growth rate, G, for the secondary grains can be given by where M is the grain boundary mobility, is the grain boundary free energy, is the average primary grain radius, A is the average difference in surface free energy between the (100) plane and planes of other orientations, t is the sheet thickness, and C is a term first proposed by zener6 which acts as a negative driving force, the effect of inclusions in holding up grain boundary motion. Since the problem of grain growth being discussed is under conditions where the matrix grain size is at least equal to the sheet thickness, the radius r is, of course, a function of the sheet thickness. The term B/r is the grain boundary driving force normally associated with inclusion inhibited or texture inhibited secondary recrystallization. Here, however, the term is modified to account for the fact that growth occurs in thin sheets. The term is the additional driving force available because of the difference in surface free energy. The purpose of the present work has been to evaluate the driving force terms of the growth equation by studying growth rates of (100) secondary grains as a function of sheet thickness and primary grain size. From these data it has been possible to determine the relative values of grain boundary energy, surface energy difference, and the inclusion term, C. EXPERIMENTAL PROCEDURE A 3 pct Si-Fe alloy was melted and cast under a helium atmosphere using electrolytic iron and a pure commercial grade of silicon as raw materials. The alloy was hot and cold rolled to a thickness of 0.6 mm, and samples approximately 5 in. long by 1 1/4 in. wide were cut from the cold-rolled sheets. Four different primary grain sizes were obtained

Jan 1, 1963

By Rodolfo V. de la Cruz

The in situ deformability of rock masses is determined by relating the applied load to the radial displacements of points on the borehole wall that are outside of the loaded surfaces. The external displacement method includes the steps in which: a) radial displacement sensors are installed to measure the change in length of a diameter of a borehole; b) unidirectional self- equilibrating pair of forces perpendicular to the direction of radial displacement measurements are applied on opposite sectors of the borehole wall, and; c) using elastic theory, the in-situ deformability of the rock mass can be related with the applied loads and measured radial displacements. The displacements outside the loaded surfaces are comparatively smaller in magnitude than displacements inside the loaded surfaces. These displacements, however, are sufficiently large and can be measured precisely by commercially available linear displacement sensors. Loads are applied by a conventional borehole jack. Existing methods for measuring the in situ deformability of rock masses yields unreliable results due to complex boundary stresses, small and varying contact areas, and the existence of fractures. It was shown that in the external displacement method, the effect of boundary pressure distribution and contact area are negligible. Also, since the displacements measured in the external displacement method were due to materials that are deeper inside the rock mass, borehole fractures have less influence on the calculated deformation modulus.

Jan 1, 1982

University of Alaska College, Alaska Mining Society (Inactive) H. G. WILCOX, Faculty .Sponsor University of California Berkeley, California Mining Association. OLEG D. SCHERBININ. President CHARLES S. PRATT, Secrctary LESTER C. UREN, Faculty Sponsor

Jan 1, 1944

By Ernest Gayford

This is a nontechnical paper on flotation, subdivided under three general headings: (I) Definition of flotation; (2) what flotation is now doing in Utah; and (3) what is the future of flotation? Definition T. A. Rickard defines flotation' as "the act or state of floating," from the French flottaison, water-line and flotter, to float. The dictionary defines flotation as "the science of floating bodies." The flotation process is a method of concentrating ores by frothing. Weinig and Palmer,2 define flotation as follows: What is the flotation process? Briefly, it consists in the agitation of finely divided ore in water containing bubbles of air or gas, a small amount of oil and, usually, other reagents, soluble and insoluble; under these conditions the small particles of native metals, sulfides, arsenides, antimonides, selenides and tellurides show a tendency to attach themselves to the films of the bubbles, and are thus carried to the surface of the water. The oxidized gangue minerals, such as quartz, feldspar, limestone, hematite, etc., show much less affinity for the bubbles, are easily wetted by the water, and either remain in suspension in the water, or sink to the bottom of the vessel. If the bubbles are sufficiently stable they can be removed, carrying their load of sulfide-mineral particles with them. Thus there can be effected a separation of the two classes of minerals from each other, assuming that the grinding has been sufficient to unlock all of the particles of different composition. The separation does not depend upon differences in specific gravity of the various minerals; in fact, the sulfides are usually heavier than the oxides, and some of the heaviest sulfide minerals are the easiest to float. A particle of mineral may be so large, however, that its weight will counteract its affinity for the film of the bubble. In most cases the ore must be fine enough to pass a screen having at least 48 meshes to the linear inch. Taggart3 defines flotation as follows: Flotation is a method of wet concentration of ores in which separation of mineral from gangue is effected by causing the mineral to float at or above the surface of a body of liquid pulp while the gangue becomes or remains submerged. The method

Jan 1, 1928

By A. H. Daane, B. J. Beaudry

The Sc-Ti system was studied by thermal, metal-lographic, and X-ray methods. Scandium was found to transform at 1334 °C from a (hexagonal) to ß which was concluded to be bee since a continuous series of solid solutions is formed between ß scandium and ß titanium at elevated temperatures. There is a minimum in the solidus at 51 wt pet Ti and 1300°C, a monotectoid at 1050°C and 49 wt pet Ti, and a eutectoid at 875°C and 91.5 wt pet Ti. The maximum solubility of titanium in a scandium is 13.5 wt pet at the monotectoid temperature, while the maximum solubility of scandium in a titanium is 6.5 wt pet at 875°C. SCANDIUM, a member of Group 111 A of the periodic table, and now called a rare-earth metal,' has become of interest recently due to its low density (2.99 g per cc) and relatively high melting point (1539°C).Spedding,' et al. have described a method of preparation of pure scandium metal and have made a study of its basic properties. Since scandium is approximately 10 to 12 pet smaller in at. diam than the other rare earths while its electronegativity and valence are the same, a knowledge of its alloying behavior in contrast to these elements should be very helpful to fundamental alloy theory. Since scandium is quite scarce and difficult to prepare in pure form, its use as a structural material by itself seems quite unlikely. However, its use in special cases as an alloying addi- tive to other low-density materials is a possible application; the Sc-Ti system was chosen for this reason and for others of fundamental interest. Scandium was suspected of having a high temperature bee form as do some of the other rare-earth metals.3'4 Since titanium has a high-temperature bee form, a continuous series of solid solutions at elevated temperatures between ß scandium and ß titanium would prove the existence and structure of the high-temperature form of scandium. The existence of a continuous series of hexagonal solid solutions at room temperature was predicted by Burkhanov and Savitskiy,5 but Hias shown to be incorrect in early X-ray studies. EXPERIMENTAL METHODS Materials. The metals employed in this investigation were crystal bar titanium and distilled scandium prepared by the method described by Spedding,2 et al. The major impurities are listed in Table I in PPm. Alloy Preparation. All the alloys examined were initially formed in a nonconsumable electrode are-melting furnace under an atmosphere of purified helium or argon. A curve based on the observed weight loss of 0.6 pet* when titanium was melted

Jan 1, 1962

By K. Stout, L. Friel

Some rock mechanics theorists believe that if a hydraulically placed backfill can be introduced in a stoped out area, which will minimize wall closure by taking high stresses across the fill with minimum compaction, then heavy ground and rock burst phenomena will be minimized. The paper will discuss a large scale laboratory project when fill strength was increased over four times by the head vibrated method and up to well over 20 times by the double placed, cemented, vibrated head method when compared to conventionally placed fills. The only preconditioning of the 60% solids by weight slurry was the addition of cement in some tests.

Jan 1, 1983

By Henry M. Otte, Ralph P. I. Adler

The changes of line position and integral line breadth in the X-ray diffraction pattern of a polycvys-talline Cu-30Zn tensile test piece, incrementally loaded (and unloaded) up to fracture, have been an-alyzed in detail. The stacking-fault probahility, cv, increased linearly with increasing strain, E, wheveas the effective domain size, De(hkl), decreased with decreasing E-1 Over the greater part of the stress-strain curve the rate of work hardening was essentially constant (about 86 kg per sq mwz), and could be correlated with the slope of stage II of the single-crystal stress-strain curve. Consequently the theories of work hal-dening (particularly those parts relating to stage 11) as developed by Mott and Hivsch and others could be applied to the observations made on the polycrystalline brass. A relationship of the form Aa = Aao - MhklEhkl between the change, Aa, in the extrapolated lattice pararneter and the rvns strain, Ehkl, was derived and found to fit the results acceptably well. From this and other relationships developed in the papev it was estimated that the equilibrium stacking-fault energy of Cu-30Zn was between 8.4 and 12.5 ergs per sq cm, in fuirly close agreement with the (corvected) value obtained by Howie and Swann (1961)43 using transmission electron microscopy. The theory of work hardening in the jorm developed and recently presented by Hirsch (1964)3 successfully described all the pvesent observations. In order to test certain aspects of the theories of work hardening, as developed by Mott,1 Hirsch,2,3 Seeger et el,4-7 and others (for review see Nabarro, Basinski, and Holt8), several recent investigations have been concerned with relating the dislocation density, p, with the shear stress, 7 (and strain, y), applied to the specimen. The results of these investigations have shown that the square root of the dislocation density appears to be linearly related to the applied shear (or flow) stress for fcc as well as bcc metals and alloys. Furthermore, the relationship appeared to apply not only to the deformation of poly-crystalline specimens, but also to stages I and I1 of the deformation of single crystals. An expression of the form has thus come into wide use. Here b is the Burgers vector for a total dislocation, G is the shear modulus, and 70 and q are constants. A review9 of available values of q shows it to have values (at room temperature) in general between 0.3 and 0.6. Forms of Eq. [1] can be deduced from, or predicted by, the current theories, and the various constants adjusted so that they are compatible with the experimentally found value of q . No unique relationship has yet been found between the dislocation density and the applied shear strain. There are several serious objections to the use of Eq. 11]. In the first place, it relates the shear stress to the density of the dislocations without regard to their arrangement, type, or distribution; the significance of the relation may therefore be justly questioned.5 In the second place, the values of the experimental quantities usually substituted into Eq. [11 are those of the applied shear stress and the total dislocation density measured after unloaditzg. The dislocation density value that should in fact be used is that for the mobile dislocations present in the specimen when under the applied load.* Finally, in cases where the values used for p, the dislocation density, are those obtained by electron microscopy, p is subject to considerable error,' both systematic and random. The corrections to be applied are still controversial. Dislocation densities can also be measured by etch-pit and other techniques,'' each having their specific limitations. An objective of the present investigation has been to obtain information about the dislocation configyration and distribution by analyzing the changes in the position and shape of X-ray diffraction profiles as a function of deformation. The X-ray techniques employed, also open to criticism, have certain advantages, however. Thus, although the X-rays diffract only from the surface layers to an effective depth of about 20 p, the measurements can be made while the specimen is under load. The value of the dislocation density obtained by the X-ray method is also subject to errors, which are different from those of the electron microscope. Though a considerably larger volume of material is sampled by the X-rays, thereby reducing some of the statistical errors inherent in the electron microscope data, the information obtained is less detailed and is dependent on the method of analysis used to obtain a value for the dislocation density. Nevertheless, important observations can be made because the aforementioned advantages outweigh some of the limitations. In the present paper the X-ray method is briefly described and applied to a brass specimens deformed in tension. The results are then discussed in terms of some of the current concepts of work hardening. 1) EXPERIMENTAL PROCEDURE Details have already been extensively published elsewhere11-14 and therefore will only be dealt with briefly here. 1.1) Materials and Specimen Preparation. Commer-

Jan 1, 1968

By AIME AIME

FEW indeed are the sections of the country where trained or partly trained workers have not already been hired by a war industry plant or will be within the near future. Yet right in the midst of the heavily industrialized East lies the anthracite area, home of a million people, whose productive power has persistently been by-passed either by private industry or by the Government Plant Site Board. The chief reason given for not locating war plants in the area is that it is not within the strategic zone, but in numerous instances elsewhere this rule has been waived. Furthermore, the anthracite region is well protected on all sides by mountains and is at all points more than 100 miles inland. Continued depression in the anthracite industry and a crippling blow dealt by the war emergency to the production of silk and rayon goods, the chief manufacturing activity of the area, have resulted in a heavy migration, particularly of trained young workers, into near-by industrial areas. At least 50,000 people are currently unemployed, with the likelihood of an increase in coming months, and as many families are on relief.

Jan 1, 1942

(Members are urged to send in for this column any notes of interest concerning, themselves or their fellow-members.) Members and visitors who registered at institute headquarters during October A. Adiassewich, St. Petersburg, Russia. Charles W. Merrill, San Francisco, Cal. A. F. Lucas, Washington, D. C. Carl J. Trauerman, Butte, Mont. Allan J. Clark, Lead, S. D. Herbert B. Cox, Boston, Mass. Prof. Loewinson-Lessing, St. Peters- James W. Malcolmson, Kansas City, Mo. burg, Russia. A. E. Sunderhauf, Paramaribo, Dutch F. Maury Gillespie, Abangarez, Costa Rica. Guiana, S. A. M. Gardner Talcott, Irvington-on-Hudson, N. Y. D. W. Brunton, Denver, Colo. A. P. Watt, Newark, N. J. Dwight E. Woodbridge, Duluth, Minn. S. A. Taylor, Pittsburg, Pa. Alexander Fyfe, Boston, Mass. Ralph Wilcox, Miami, Ariz. Robert A. Seip, Wilkes-Barre, Pa. William J. Cox, Denver, Colo. A. J. Eveland, Boston, Mass. E. P. Ross, Duquesne, Pa. M. F. Sayre, Brewster, N. 1. H. Mortimer-Lamb, Montreal, Canada. Albert Sauveur, Cambridge, Mass. F. L. Grammer, Leesburg, Va. Robert H. Leach, Brockton, Mass. R. R. Moore, Mexico City, Mex. Steinar Foslie, Kristiania, Norway. Charles E. van Barneveld, San William A. Wong, Honolulu, Hawaii. Fran¬cisco, Cal.

Jan 11, 1913

By Effingham Humphrey

THE Lehigh Valley. Coal Co. finished the rebuilding of its Drifton No. 2 breaker at Drifton, Pa., in the summer of 1917. The new construction comprises an addition and the complete remodeling of the old breaker. It is of interest to note that the old structure was the first iron breaker erected in the anthracite region. THE OLD BREAKER This old breaker was built by the Cross Creek Coal Co., under the direction of the late Eckley B. Cole, in 1888-89, and was fully described by him in the Transactions.1 The columns were cast iron, 8,'10 and 12 in. square. The floors and partitions in pockets were cast-iron ribbed plates. The struts were cast iron of "H" section; the other members were of structural iron either rolled I-beams or built-up sections. The sizes of the rolled beams varied from 6 to 20 in. deep, while the built-up sections, made of plates and angles, varied from 6 to 63 in. in depth, so that there apparently was no rule to determine the type of section used. In the remodeling of the old structure, practically everything was taken clown excepting the columns and roof, and such beams as were necessary for temporary construction purposes, and, therefore, a close inspection of the old structural members could be made and the effect of the acid water oil them could be noted. The cast-iron members were but slightly attacked by the water, while the wrought-iron beams, in the wet places, were corroded almost to failure.

Jan 2, 1918

NEW MEMBERS The following list comprises the names of those persons who became members during the period Mar. 1 to 15, 1914: Members ADAMS, JOHN H., Cons. Engr First National Bank Bldg., Birmingham, Ala. ALEXANDER, WILLIAM H., Miner 80 Maiden Lane, New York, N. Y. AUSTIN, EDGAR TAYLOR, Asst. Smelter Supt., Mond Nickel Co., Ltd., Coniston, Ont., Can. BAKER, DANIEL, JR., Asst. Treas., Standard Lime & Stone Co. 524 Equitable Bldg., Baltimore, Md. BALL, MAX WAITE, Geologist U. S. Geological Survey, Washington, D. C. BARREN, HARRY B., Supt. Blast Furnaces, Inland Steel Co., Indiana Harbor, Ind. BAUMANN, HENRY N., JR., Amalgamator 365 Lynn St., Seattle, Wash. BLACK,, THOMAS B., Min. Engr Care Vulture Mines Co., Wickenburg, Ariz. BRADT, HARLAN H 429 West 111th_ St, New York, N. Y.

Jan 4, 1914