Search Documents

By F. S. Young, K. E. Gray

Drilling tests with a 11/4-in. diameter roller bit were performed on Berea and Bandera sandstones and Leuders limestone using water and two conventional drilling muds as circulating fluids to evaluate the influence of dynamic filtration on penetration rate. The muds possessed widely differing API fluid-loss properties. Mud filtrate was constrained to flow beneath the bit; no filtrate flowed radially through the borehole wall. Rock pore pressure at three different locations ahead of the bit, cumulative filtrate volume, borehole pressure and bit location were monitored during drilling. The rock samples, cored in three orientations with respect to bedding planes, possessed a wide range of liquid permeabilities. and were drilled at borehole-to-formation pressure differentials of 0, 250, 500 and 1,000 psig. The effect on penetration rate of API fluid loss, borehole pressure and rock permeability was studied. Rock permeability damage and pore pressure gradients beneath the bit were evaluated. The importance of borehole-to-formation pressure differential was illustrated for each drilling fluid and rock permeability combination. Penetration rates decreased with increased borehole pressure and reduced fluid loss. The observed penetration rate reduction due to changing fluid Ioss was attributed to decreased filtrate flow and improved mud cake plastering hy the low fluid-loss mud. The reduction in filtrate flow could not be related to spurt-loss phenomena. Rock permeability influences penetration rate through particle invasion ahead of the hit, which damage leads to high pressure gradients. Penetration rate variance with sample orientation was evident for water-drZled samples but less obvious for mud-drilled rocks. Permeability damage beneath the bit ranged from 1 to 3 cm. Maximum damage occurred in the first 0.1 cm. Pressure gradients varied with API fluid 10.s.s and could be correlated with penetration rate. The pressure gradient was found to influence penetration rare in rocks of all permeabilities tested. INTRODUCTION Early microbit and small-scale drilling experiments proved to be invaluable contributions to understanding the mechanics of drilling at depth. For example, the effect of borehole-to-pore pressure differential on drilling rate was demonstrated conclusively by Murray and Cunningham', Eckel' and others .' However, the effects of various drilling fluid properties on drilling rate, particularly filtration, have not been studied extensively on a laboratory basis. Microbit correlations of penetration rate with different viscosity and API fluid-loss muds led EckelV o conclude that viscosity and density. more than API fluid loss, were the most important fluid properties in controlling drill bit penetration rates. Ferguson and Klotz6 studied filtration beneath the bit and stated that the maximum amount of filtrate which could conceivably flow beneath a drilling bit could be described by a potential function associated with flow from a moving disc source. and be characterized by a depth-of-filtrate invasion. Invasion depth is a function of penetration rate, formation porosity and permeability, flooding efficiency, pressure difference between borehole and formation and borehole radius, assuming that no filtrate flows through the borehole walls. Electric analog and experimental measurements were obtained, assuming no plugging of the formation pores. Theoretically, filtrate invasion was predicted to extend from 1- to 15-hole radii beneath the cutting surface; experimental results indicated that the extent of invasion was only Y2 in. Comparing these data with results of core-plugging experiments by Norwak and Krueger' led Ferguson and Klotz to state that the drilling operation apparently contributes to higher filtration rates than are observed in nondrilling core filtration tests in which the core face is jetted and scraped. Glenn and Slusser: in describing a linear filtering system in which a rotating bit continuously scraped mud cake from the surface but did not penetrate Alundum cores, stated that mud-solids invasion and permeability damage of the cores were most severe in the first 2 to 3 cm. The filtrate flow rate through the core was found to stabilize after sufficient time had elapsed for the formation of an internal mud cake whose effective permeability was estimated to be 50 to 300 times as high as that of bulk filter cake. Krueger and Vogel reported core permeability damage depths up to 12 in. during a 5-day exposure period in which filter cake buildup was prevented. Havenaar pointed out that the discrepancy between reported and calculated values of filtrate volume obtained in the experiments of Ferguson and Klotz was due, among other things, to failure of the reported API fluid loss to truly represent filtration beneath the bit. Williams," Pro-koplz and others"" have shown that dynamic filtration tests (where a flow of fluid parallel to the filter surface continually erodes the deposited filter cake until a dynamic equilibrium between wall-shearing forces and normally directed compaction forces is attained) yield higher filtration rates than do static tests. Cunningham and Goinss reported results of drilling tests in impermeable shales. They found that by reducing

By H. E. Wilborg

This chapter deals with those sands employed by the foundries for the manufacture of cores and molds used in the casting of such common metals as steel, gray iron, ductile iron, aluminum-based alloys, and copper-based alloys. Most metal is cast in "green sand" molds in which the sand mixture, consisting primarily of silica, clay, and water, forms a plastic material. This plastic material is rammed around a pattern in a split box called a flask, then the box is separated, the pattern is withdrawn, and the metal poured. These green sand molds are broken apart when the metal has solidified. The sand is then remixed and a new mold made for the next casting. To a lesser extent silica sand is mixed with resins or oils and, after forming, the mixture is hardened either by heat or chemical reaction. In any case, the foundry mold or core is used just once before being broken up and remixed for manufacturing another core or mold. By far the greatest consumption in the foundry is of those types of sand high in silica, low in clay (under 0.5%) and occurring in numerous locations thoughout the United States.

Jan 1, 1975

By F. C. Stanford

THE work of an engineer is to direct natural forces so that they bring about the results that he wishes to secure. Heretofore he has concerned himself chiefly with physical forces and inanimate objects, until he has secured a truly marvelous degree of control over them. The great problem of the present age is to secure a like degree of knowledge and control of the human factor. Progress has already been made along this line, but, it is only a beginning. Wilhelm Ostwald says that scientific knowledge enables a man to be a true prophet; but it must be remembered that a good many people do not seem to be able to maintain a high average in prophecy. In short, the average of knowledge is not equal to the average needs of the present time, but continually fails to keep pace with it. It has been aptly said that the really essential need of the period is for more brains; if we only had sufficient knowledge and sagacity we could not only solve all difficulties, but prevent them from arising. This generalization holds good for an industrial organization. The most vital need of the management is for more brains. The logical course for an engineer in charge of an industrial organization is, therefore, to direct whatever forces may be at his command toward the development, training, and guiding of all the brains in his organization. This is easier said than clone, for it involves the carrying on toward two objectives, the maximum of productive work, and the development of the individuals who perform it. This is essentially like the rebuilding and enlarging of a plant, keeping it in full operation the while. On the other hand, if the aim is merely for maximum production from an organization, without offering opportunity for development, the final outcome will necessarily be like that f a plant that is driven at full capacity without stopping for repairs or improvements; it eventually becomes so run down that either a complete rebuilding is necessary or else it has to be abandoned.

Jan 2, 1918

Jan 1, 1933

By J. Wesley Pullman

It is stated by Dr. Tuttle in a paper read before the New Jersey Historical Society, that the celebrated Dickerson mine at Succasunna, Morris Co., N. J., yielded ore, about as early as 1710, for use at the Whippany forge, on Rockaway River, between Rockaway and Boonton. The ore was, for some time, free to all who chose to dig it. The tract embracing the Dickerson mine mas taken up, on account of its minerals, in 1713 or 1714, by John Reading, who sold it in 1716 to Joseph Kirkbride. John Jackson built a forge in 1722 on the Rockaway River a mile west of Dover. The ore here worked was probably chiefly from the Dickerson mine, but a portion may have been Hibernia. Hon. E. D. Halsey, of Rockaway, K. J., writes me: It is quite possible that the ore was at first taken from the outcrop of Hibernia by anybody who wanted it. The property first had an owner, May

Jan 1, 1886

By J. O. Lewis

Oil wells usually reach their maximum daily output shortly after they are completed. From that time they decline in-production, the rapidity of decline depending on the output of the wells and on other' factors governing their productivity. The production curve of a well shows the mount of oil produced per unit of time for several consecutive periods; if the conditions affecting the rate of production are not changed by outside influences, the curve will be fairly regular, and, if projected, mill furnish useful knowledge as to the future production of the well. By the aid of this knowledge the value of a property may he judged, and proper depletion and depreciation charges may be made on the books of the

Jan 2, 1918

Andrew Carnegie, America's best-known ironmaster and philanthropist, died at his home at Lenox, Mass., Monday, Aug. 11, after a three days' illness. A pioneer in the steel industry, he introduced into this .country the Bessemer process And formed the plans that have resulted in this country's supremacy in the steel markets of the world. Known throughout the world for his, gifts, he is also known to engineers as the donor of the home of their National Societies and as the founder of the Carnegie Institute of Technology, of Pittsburgh. For many years, also, he was an honorary member of the American Institute of Mining and Metallurgical Engineers, the American Society of Mechanical Engineers, and of the Engineers Club of New York. What he considered the secret, of his success is shown by the epitaph he wrote for himself, "Here lies a man who knew how to enlist in his service better men than himself." He was buried Thursday, Aug. 14, in Sleepy Hollow Cemetery, Tarry-town, N. Y., the funeral services being private, in accordance with his wish.

Jan 9, 1919

By G. B. Kasik, George Sachs, George Espey

IT has been reported frequently that the hardness and strength vary over the cross section of cold-worked, particularly cold-drawn, material. Brass rod and wire usually has been found to possess a maximum strength and hardness near the surface.1,2 According to Sachs,1 the center fiber has about the same strength as a wire stretched by the same amount in a tensile-test machine, the strength increasing toward the surface (Fig. I). These differences are particularly large for wire given a small reduction on drawing through a die with a wide opening. However, with increasing reduction and hardness, a tendency to form a thin soft surface skin becomes apparent. On the contrary, copper wire has usually been found to possess a soft surface skin" and it has been reported by Harris3 that during the cold-drawing of hot-rolled wire the surface layer becomes increasingly softer than the core, while the layer of maximum strength moves toward the core, it being found near the surface at first. The increase of strength and hardness from the core to the skin is readily explained by the observation that, in addition to the stretching, the layers of a rod or wire are sheared more the closer they are to the surface.1,6-8 However, the presence of a soft surface layer can be attributed only to an annealing effect. The source of such a softening might be the extremely high temperature that originates from the friction between [ ]

Jan 1, 1941

Ninetecn papers and a round table. as follows: The Future of the American Iron and Steel Industry (Howe memorial Lecture), by Zay Jeffries; Rote of Carbon Elimination and Degree of Oxidation of metal Hath in Isasic Open-hearth Practice. 11, by ,Alexander L. Feild; A New Method for determining lron Oxide in Liquid Steel, by C. H. Herty. Jr., J. M. Gaines. Jr., H. Freeman and M. W. Lightner; I'racticsl Obarrvntions on Manufacture of basic Open-hearth, High-carbon Killed Steel, by W. J. Itcagan; Production of Gray lron from steel Scrap in the Electric Furnace, by T. F. Baily; reclaim ing Steel-foundry Sanda, by A. H. Dierker; Influence of Rate of Cooling on Dendritic Structure and Microstructure of Some Hypocutectoid Steel, by Albert Sauveur and C. H. Chou; Transformation of Austcnite at Constant Subcritiral Temprratures, by I?. S. Dnvenport and E. C. Bain; Progress Notes on the Iron-silicon Equilibrium Diagram, by Bradley stoughton and S. Greiner; Influence of Nitrogen on Special Steels and Some Experiments on Case-hardening with Nitrogen; by Shun-ichi Satoh; Production and Some properties of Large Iron Crystals, by N. A. Ziegler: Tensile Properties of Rail and Other Steels at Elevated Temperatures, by John R. Freeman, Jr. and G. Willard Quick; Endurance Properties of Steel in Steam, by T. S. Fullcr; Development of Casing for Deep Wells; a Study of Structural Alloy Steels, by F. W. Bremmer; Electrolytic Iron from Sulfide Ores. by Robert D. Pike, George H. West, L. V. Steek, Ross Cummings and B. P. Littlc; Sintering Limonitic Iron Ores at Ironton, Minnesota, by Perry G. Harrison; Concentration of the mesabi Ilematites, by E. W. Davia; Resistance of Iron Ores to Decrepitation and Mechanical Work, by T. L. Joseph and E. P. Barrett; Experiments Demonstrate Method of Producing Artificial Manganese Ore, by T. L. Joseph, E. P. Barrett and C. E. Wood; Iron Ore Round Table.

Jan 1, 1930

By G. Das, S. V. Radcliffe

The substructural features developed in tungsten as a function of annealing temperature (up to 2200°C) and type of material [undoped and doped powder metallurgy (PM) tungsten and electron beam melted tungsten] have been investigated by transmission electron microscopy. For doped PM tungsten wires, characteristic "par-ticulate" substructural features developed rapidly with increase in annealing temperature above 700°C. The features consisted of parallel rows of elongated or circular shapes (500 to 1000A diam) lying along the direction of the wire axis and were identified as internal voids by diffraction contrast experiments. In recrystallized doped PM rod, larger voids were observed and were identified by precision dark field analysis to be cubic in shape and bounded by (100) planes. In marked contrast with both the doped PM materials, recrystallized undoped PM rod exhibited only very occasional and randomly arranged voids. Furthermore, no voids were observed in either material after electron beam melting. The high concentration of voids in the doped PM materials is attributed primarily to vaporization of doping additions or their pvoducts situated at the original grain boundaries , whereas the few voids in undoped material are considered to be traces of microporosity which were not eliminated during sintering. A tentative mechanism is suggested for the dezlelopment of the voids in relation to the processing sequences (sintering and working) and to the subsequent annealing. In recent years, a characteristic substructural feature consisting of rows of small elongated or circular regions of light contrast lying along the direction of working has been seen in thin foil electron microscopy studies of annealed sheet, wire, and rod tungsten. These features were present in the published micrographs of sheet by Weissmann et al.1 and of wire by Meieran and Thomas2, although the authors did not draw attention to them. Wronski and Fourdeux3 observed similar features in sintered rod tungsten (it was not specified whether or not the material was doped*) and interpreted them on the basis of their ap- particles, based on extraction replica evidence from the fracture surface of the initial hot-rolled slab material from which the sheet was prepared. No diffraction contrast experiments on the features were reported in any of these studies. The present investigation was undertaken with the primary objectives of: a) identifying the nature of these substructural features in tungsten by electron diffraction contrast experiments, since the contrast for voids can be expected to differ from that for crystalline or glassy particles, and b) elucidating the origin of the features and their development. For the latter purpose, doped and undoped powder metallurgy tungsten was obtained as rod and wire to represent different stages of reduction during final processing. These materials were examined both in the as-processed condition and after annealing to successively higher temperatures. In addition, the same doped and undoped materials were examined after vacuum melting in rod form. I) MATERIALS AND PROCEDURE Doped powder metallurgy (PM) tungsten wire (commercial purity 99.9 pct W) was obtained in the as-drawn and surface ground condition (0.030 in. diam "ground seal rod"). Doped and undoped tungsten rod (0.075 in. diam) representing an earlier stage of final processing was obtained from the same commercial source (Refractory Metals Division, General Electric Co.). Lengths of both the doped and undoped rod materials were single-pass melted in an electron-beam zone refiner to examine the effect of vacuum melting on the substructure. Annealing was carried out in a tungsten crucible in a tantalum strip resistance furnace under a vacuum of l0-15 mm Hg. Longitudinal sections of the wire and rod materials were examined by light and electron microscopy. The preparation of thin foils suitable for electron transmission from 0.030 in. diam tungsten wire and the rod specimens was carried out by means of a high-precision microjet technique developed to provide lack of jet stability and precise control of the area thinned. The method is described in detail elsewhere.' The foils were examined in a JEM 6A electron microscope using a goniometer stage (±20 deg tilt, 360 deg rotation) and operated at 100 kV. To minimize contamination problems a 200 µ condenser aperture was used in conjunction with a useful beam current of 50 µA. II) RESULTS AND DISCUSSION A) Diffraction Contrast Analysis. In order to determine the optimum conditions for the development of the substructural feature, a series of isochronal 30 min annealing experiments were carried out on specimens of the doped PM tungsten wire. The transmission electron microscopy analysis showed that the as-drawn wire, Fig. 1(a), consists of 'fibers' whose long axis is closely parallel to the wire axis of (110). The fiber width averages some 0.5 µ. Dense disloca-

Jan 1, 1969

By S. W. Ross

In 1936 a description of the plant (Fig 1) and process employed by the Electrolytic Zinc Co. of Australasia Ltd. for the recovery of zinc from zinc concentrate by the electrolytic process was prepared. † During the twelve years which have elapsed since the preparation of the earlier paper, several major changes in the metallurgy of the process have been introduced. It is the purpose of the present paper to give a general description of these changes and thus to bring up to date the description of the plant and process. Summary The major changes in Risdon practice since 1936 have been: 1. Replacement of two stage roasting by a preliminary roast followed by the flotation of all the leach residue and the roasting of the flotation concentrate. 2. Screening of all calcine fed to the pachucas. 3. Continuous leaching of calcine and improved classification of pachuca discharge. 4. Close control of hydrogen ion concentration during purification for iron removal. 5. Recovery of cobalt as a good grade oxide. 6. Production of part of the zinc output in the form of "four nines" metal (99.99 pct purity). 7. Closer spacing of electrodes thus increasing the potential output of cathode zinc per cell by 50 pct. Changes which are in prospect and for which construction work is proceeding at the present time involve the starting up of: 1. Two suspension roasters. 2. A contact acid plant to produce 150 tons‡ of acid per day and replacing the existing Mills Packard chamber plant. 3. Extra power station capacity to permit greater current flow to existing cell room units. This will increase the output of cathode zinc from about 245 to 290 tons per day. Plans for the future envisage the building of an ammonium sulphate plant, the first unit of which will produce about 50,000 tons per year, and improved treatment of zinc plant residue for the recovery of zinc, lead and other metals. At the end of this paper tables of metallurgical data are presented relating to the year ending June 30, 1948. Details of Changed Practice Output In 1936 the production of cathode zinc amounted to about 200 tons per day. This has since been increased to about 245 tons per day while plant extensions are practically complete which will permit of an output of about 290 tons per day in the near future. Roasting Division ROASTING POLICY A major change has occurred in the roasting policy. Twelve years ago the method in use was to carry out a two stage roast in the first stage of which sulphide sulphur was reduced to about 6 pct. The pre-roast calcine was re-roasted in modified Leggo furnaces using coal as fuel, sulphide sulphur being reduced to about 0.8 pct. The whole procedure was described on pp. 482491 of the earlier paper. Although this roasting procedure had certain advantages it possessed some distinct disadvantages. For instance, it appeared uneconomical to heat up the entire input of pre-roast calcine to roasting temperature by the expenditure of fuel in order to oxidise a few percent of sulphide sulphur. It was argued that if the pre-roast calcine were leached and a process could be developed for the recovery of a zinc sulphide concentrate from the leach residue, this concentrate, small in weight compared with the pre-roost calcine, would probably roast autogenously, thus virtually eliminating the expenditure of fuel as well as greatly increasing the weight of sulphur oxidised per square foot of furnace hearth area. The obvious method of producing a suitable concentrate from leach residue was by flotation. It will be recalled (see p. 495 of the earlier paper) that when two-stage roasting was practised the leach residue was classified, the granular fraction was ground and floated while the slime fraction was thickened, filtered and dried ready for shipment to a lead smelter. This process worked quite successfully. However, when trials were made of leaching a calcine carrying several percent of sulphide sulphur the granular fraction still floated well, but the slime fraction carrying 8-10 pct sulphide sulphur yielded very poor results when subjected to flotation. This fact held up the application of "pre-roast" leaching for many years. However, successful flotation of the slime fraction of leach residue was finally achieved and in August 1940 the slime flotation plant began operation, while the leach-

Jan 1, 1950

By F. W. SUTTER

IN order to have ore available on the completion of the beneficiation plant at Clifton and to provide for continuous production while underground development was carried out, it was decided to develop an open-pit through the crest of a long hill in which the ore outcropped, using 40-ft. vertical benches.

Jan 1, 1943

Institute of Metals - Iron and Steel - Mineral Industry - Industrial Minerals Year ?Division - Petroleum Division ? Division - Coal Division - Education Division -Division 1918 W M CORSE 1919 1920 W. H BASSETT 1921 1922 W B PRICE RALPH ARNOLD 1923 E DEGOLYER 1924 G K ELLIOTT 1925 F JULIUS FOHS 1926 PAUL D MERICA 1927 JOHN M LOvEJOY 1928 S SKOWRONSKI A W AMBROSE RALPH H SWEETSER

Jan 1, 1952

By O. C. Ralston, William C. Hunter

DUring experimental study on the separation of a zinc concentrate from the heavy sulfide ores of Jerome, Ariz., a great deal of attention has been given to proper activation of the sphalerite content of the ore. The sphalerite at Jerome contains enough iron to class it as a marmatite, as picked specimens have only about 60 per cent. zinc, whereas pure zinc sulfide contains 67 per cent. zinc. This marmatite in large pieces is black in color, but in dry powdered state is brown. A flotation froth made from it has a silvery black luster in comparison with a brassy luster caused by chalcopyrite which occurs in the same ores. The sample used in most of the experiments described below consisted of about 3000 Ib. of diamond-drill core from the zinc-bearing orebodies of the United Verde mine, and had the following analysis: Per Cent. Per Cent. Oz. peR Ton Cu............... 0.695 Al2O3............ 0.83 Ag................. 1.30 Zn............... 6.17 S................ 43.35 Au................ 0.02 Fe...............36.23 CaO............. 0.46 SiO2............. 9.27 Mineralogically, this analysis is calculated to the following, which is in agreement with the microscopic examination: Per Cent. Per Cent. Chalcopyrite................... 2.0 Schist........................... 3.2 Marmatite..................... 10.32 Quartz........................... 8.2 Pyrite........................ 73.0 Calcite.......................... 0.9 All samples were ground in a laboratory ball mill in order to leave about 3 per cent. on a 200-mesh sieve, fine grinding being essential to liberate the minerals in the ore. Most of the Jerome ores are so intimately crystallized that reasonably complete unlocking by grinding does not take place until 800 mesh is approached. Therefore, the 200-mesh grind adopted contains a considerable amount of locked mineral grains, but not so much as to render impossible the preparation of commercial grades of concentrate.

Jan 1, 1930

By D. K. Bose, C. K. Gupta, K. U. Nair

A new approach to processing an indigenously available low made molysulfide concentrate by chlorination with elemental chlorine in presence of oxygen is reported. Recovery of nickel and copper values associated with the sulfide concentrate by suitably treating the residue obtained after chlorination is also reported.

Jan 3, 1978

TECHNICAL COMMITTEES Iron and Steel JOSEPH W. RICHARDS, Chairman. J. E. JOHNSON. Js., Vice-Chairman. ARTHUR S. CALLEN, Secretary, 453 Chestnut St., So. Bethlehem, Pa. SUB-COMMITTEES IRON ORE DWIGHT E. WOODBRIDGE. Chairman. ERNEST F. BURCHARD, WILLIAM KELLY. CHARLES F. RAND, FELIX A. VOGEL. BLAST FURNACES H. A. BRASSERT. Chairman. WILLIAM H. BLAUVELT, AMBROSE N. DIEHL, JAMES GAYLEY, RICHARD V. McKAY.

Jan 10, 1915

By Allen D. Garrison

THE chemistry of clays and shales has been assuming increasing importance in the petroleum industry, and two factors have greatly influenced this trend. The first has been the growing evidence that the marine shales are source beds, and that the petroleum compounds have migrated to the sand reservoirs overlying or underlying these shales: the second has been the demand for drilling fluids better adapted to penetrate these marine shales without difficulty and expense. ORIGIN AND GENERAL COMPOSITON OF CLAYS AND SHALES Clays, shales and surface soils are all closely related materials. They are mixtures of finely divided compounds formed during the weathering of the solid crust of the earth. Their nature is essentially colloidal; that is, their behavior is determined by the state of division of the materials and the surface reactions of the smallest grains. Many of their chemical changes affect only the exposed areas and do not involve the interior of the grains of matter. The extent of these reactions is more nearly proportional to the area of the substances than to their mass, therefore it is possible for a small amount of a material in an extremely fine state of division to completely dominate the character of the mixture. More than 83 per cent of the crust of the earth is composed of three elements-oxygen, silicon and aluminum. Consequently, the corrosion products of the crust are predominantly aluminosilicates, or compounds of aluminum, silicon and oxygen. If we add the compounds of six elements-iron, calcium, sodium, potassium, magnesium and hydrogen-more than 98 per cent of the crust has been accounted for. These six elements, together with the first three, also appear in soils, clays and shales. But direct chemical analysis is of little value in describing the nature of such materials. Many chemical individuals may be present in variable amounts, and the extreme subdivision of any one of the individuals may contribute qualities that dominate the mixture.

Jan 1, 1939

By Walter J. Johnson

The coals in northern Wyoming and Montana are free-burning and non-caking and range from lignite to bituminous C in rank. Strip and underground mining are employed to supply railroad, utility, industrial, and domestic fuel. The market area includes Iowa, Nebraska, Minnesota, North and South Dakotas, Wyoming, Montana, the Pacific Northwest, and western Canada. THE larger producing coal mines in northern Wyoming are located in the Powder River Basin lying between the Black Hills region of South Dakota, eastern Wyoming, and the Big Horn Mountains in north central Wyoming, see Fig. 1. The mines are located particularly in the area along the route of the Chicago, Burlington & Quincy Railroad from Gillette, Wyo., to a point approximately 15 miles northeast of Sheridan, Wyo. Fig. 2 is a graph of coal production in the state of Wyoming from 1918 to 1951. Across the Big Horn Mountains lies the Big Horn Basin, situated between the Big Horn Mountains and the Rocky Mountains proper. Mining in the Big Horn Basin is almost entirely confined to a small area known as the Gebo Field, near the town of Kirby, which is located on the Chicago, Burlington & Quincy Railroad. This paper will describe present operating areas, making only brief reference to the history of mining and marketing primarily because of the large area to be discussed. The coal beds presently mined in the Powder River Basin are all of Tertiary age and are of Fort Union and Wasatch formations of Paleocene and Eocene ages, see Fig. 3. The Fort Union formation, consisting of 2000 to 3200 ft of alternate sandstone, shale, and coal, is divided from oldest to youngest into the Tullock, Lebo Shale, and Tongue River members. Most of the mineable coal is in the Tongue River member, which is 500 to 800 ft thick. The Carney coal bed, varying from 7 to 20 ft in thickness, is considered the base of the Tongue River member. About 85 ft above the Carney is the Monarch bed, ranging from 18 to 42 ft in thickness. At approximately 210 ft above the Monarch is what is locally known in the Sheridan district as Dietz No. 3 bed, which varies from 12 to 30 ft in thickness. One hundred feet above the Dietz No. 3 is Dietz No. 2 bed, which is 7 to 12 ft thick. At about 100 ft above the Dietz No. 2 is Dietz No. 1 bed, 7 to 15 feet in thickness. Two hundred and fifteen feet above Dietz No. 1 is the Smith bed, approximately 5 ft thick. One hundred twenty-five feet above the Smith is the Roland bed, which is estimated to be approximately 13 ft thick. The Roland bed is considered the base of the Wasatch formation, which in the Powder River Basin is 1000 to 3500 ft thick and is composed largely of shale, sandstone, and coal. The foregoing measures are the only ones above the Tongue River member that have been mined in the Sheridan field. To the east of the Sheridan field, particularly in the area of Gillette, the Roland bed is considerably thicker and is considered the thickest and most extensive coal bed in Wyoming, reaching a maximum thickness of 106 ft. From 125 to 225 ft above the Roland lies the Arvada bed, average thickness 9 ft. Three hundred seventy-five to four hundred feet above the Arvada is the Felix bed, which reaches its maximum thickness of 30 ft near Echeta on the Chicago, Burlington & Quincy Railroad. East of the Powder River the bed averages more than 10 ft in thickness, but it thins in a northwesterly direction. The highest mineable coal in the Powder River field is the Healy bed, about 400 ft above the Felix bed and exposed only in the highest parts of the area where much of it has been burned along the outcrop. Where it has not been burned, the thickness at most of the outcrops is 10 to 15 ft.

Jan 1, 1954

A method has been developed to remove calcite from the leaching circuit in the uranium in situ leaching system. The process involves injecting the leachate and a pH control agent tangentially into an inverted cone reactor containing calcite seed catalyst. The leachate can be treated at high throughput to obtain clear effluent containing 5 ppm or lower Ca. Both lime and ammonia are effective pH control agents and consumed according to stoichiometry.

Jan 1, 1985

By A. M. Turkalo

IT is a well-known fact that martensitic steels show a greater resistance to brittle fracture than do pearlitic and bainitic steels. It was, therefore, thought worthwhile to investigate the mode of brittle fracture with respect to structure by studying the effect of various austenite decomposition products on the propagation of brittle fracture in steel by means of electron microscopy. Newly developed replication techniques together with the advantages of the electron microscope such as great depth of field, available high magnification and easy adaptation to stereophotography make electron microscopy very suitable for fracture studies. EXPERIMENTAL PROCEDURE An essentially plain carbon steel containing 0.56 pct C, 1.30 pct Mn, 0.02 pct P, 0.03 pct S and 0.22 pct Si was used in this investigation. The following table gives the heat treatments used to obtain the various austenite decomposition products: The resulting austenite grain size from the 870°C austenitization treatment was about an ASTM No. 7 grain size. The specimens which were 2 in. long, 1/4-in. diam bars were austenitized in a tube furnace through which argon gas was blown. The tube was not, however, air-free and the specimens were not completely oxide-free. Isothermal treatments were done in a lead bath. With the exception of the fully hardened specimen and the one as-isothermally transformed at 300°C the heat treated specimens were notched in the following fashion with a jeweler's saw. A cut about 0.08 in. deep was made perpendicular to the length of the bar. The specimen then was rotated about 45 deg and another cut about 0.08 in. deep was made. In the case of the hard martensitic and bainitic specimens, only one cut was made and the depth was not controlled. The design of the two-cut notch caused fracture to initiate at the point of intersection of the two saw cuts. The specimens were broken at -196°C in a Charpy impact testing machine. In order to hold the specimens securely in the impact machine two square pieces of mild steel were made about 5/8 in. long having the same cross section as that of a standard Charpy specimen but containing a hole 1/4 in. diam through the center of the cross-section. These adapters were slipped over the ends of the test specimen which was then secured tightly by means of set screws in the adapters. The specimen with the adapters was cooled to -196°C in liquid N,, then placed in the impact machine and broken within 3 sec. One half of the broken specimen was used for the electron microscope study of the actual fracture surface. The other half was nickel-plated and a cross section through the notch and fracture was polished for electron microscope examination. Carbon replicas of the fracture specimens for the electron microscope study were made essentially according to Bradley's evaporation technique.' Both direct carbon and two-stage carbon replication techniques were used. In the case of the direct carbon technique, a thin layer of carbon was evaporated first at an angle of about 45 deg to the mean fracture surface and then another film of carbon was evaporated normally to the fracture surface. The carbon replica was freed electrolytically.2 The specimen was made an anode in a 10 pct Nital polishing solution. It was etched intermittently by shutting off the power now and then. The freed replica was washed in 40 to 50 pct water solution of nitric acid for 10 min or so, then washed in water and picked up on a screen for examination. The two-stage carbon replication technique involved first making a primary replica of cellulose * acetate from which a carbon replica was then made. One side of a strip of cellulose acetate wet with acetone was pressed lightly against the surface of the specimen, allowed to dry and then stripped. Prior to the deposition of carbon, which was done at 90 deg to the cellulose acetate replica surface, chromium was evaporated at 45 deg. After the carbon evaporation the cellulose acetate was dissolved in acetone according to the Jaffe method3 leaving the carbon replica preshadowed with chromium for examination.

Jan 1, 1961